Year of construction: 1973, Condition: like new (used), Used BRONX Heavy Duty Initial Pinch Pyramid bending rolls. Year of manufacture : 1973. Fgsb Emyeh U Rzge I Tsb MACHINE FORMERLY INSTALLED AT ROLLS ROYCE PLC IN DERBY UK. IMMEDIATELY FOR SALE AND NOW LOCATED IN BELGUIM WHERE IT CAN BE INSPECTED. SPECIFICATION CAPACITY Two sets of dimensions which are shown below as "Prebending & Rolling" and then "Rolling only". Material Mild Steel Mild Steel Tensile strength 28/32 tons/sq.in 28/32 tons/sq.in Maximum width 11’(3350mm) 11’(3350mm) Maximum thickness at this width 2” (50mm) 2½” (63.5mm) Minimum inside diameter of rolled cylinder at maximum capacity 30’ (762mm) 37 ½’ (953mm) Maximum thickness of plate when hot rolling (finished rolling temperature 850° C.) 4” (102mm) 5” (127mm) Minimum inside diameter of rolled cylinder at maximum capacity hot rolling 40” (1016mm) 50” (1270mm) MAIN PARTICULARS Diameter of all rolls - 27” (686mm) Body length of rolls - 11’2”(3403mm) Rolling speed - 12 f.p.m. (3600mm/min) Main drive motor - 150 H.P. Slip Ring Type Two bottom roll adjusting motors, each - 50 H.P. Slip Ring Type Combined operation of swing down bearing and top roll counterbalance - Hydraulically applied Hydraulic power pack motor - 10 H.P. Electrical equipment to be suitable for operation on a supply of - 400/440 volts, 3 phase, 50 cycles CONE ROLLING ATTACHMENT: To facilitate the rolling of taper or conical forms, a skid plate is fitted to the inside of the non-drive end housing. ELECTRICAL EQUIPMENT Motors: Main Drive - 150 H.P. half hour rated – slip ring screen protected – foot mounted type. Bottom Roll Adjustments - 50 H.P. half hour rated – slip ring screen protected – foot mounted type. Hydraulic Power Pack Motor - 10 H.P. continuously rated – Squirrel cage – screen protected – foot mounted type. Control Gear: Main Drive - Drum type reversing control gear with 5 minute rated wire wound resistances, designed to pass 100% full load on the first notch or operating position in each direction. The controller will be fitted with off position interlock and limit switch rings where necessary. Bottom Roll Adjustments - Drum type reversing control gear with 5 minute rated wire wound resistances designed to pass 100% full load on the first notch or operating position in each direction. The controllers will be fitted with off position interlock and limit switch rings where necessary. Hydraulic Power Pack - Direct-on-line contactor type starter, operated from a maintaining type push button station. Solenoid valves for operating cylinders are push button operated. Note: Full protection to be provided for all the above control gear by a circuit breaker, incorporating overload and no-volt protection. FEATURES AND EQUIPMENT Spare Roll included with the machine. LENGTH TBA MM WIDTH TBA MM HEIGHT TBA MM WEIGHT 95 tonnes NOTE: The information contained herein is provided in good faith, but however due to unforeseen errors or omissions cannot be binding as to accuracy.

Condition: ready for operation (used), Year of construction: 2015, General Data Measurements width 4800 mm Measurements depth 8800 mm Fgjb Emev Svzcsy I Tjb Measurements height 2400 mm Machine weight 12000 kg Control Unit Brand SIEMENS Model Sinumerik 840 D Main Drive Laser power 5000 Watt Laser type TruDisk 5000 fiber Number of axis 3 Movement X-Axis Movement 3000 mm Y-Axis Movement 1500 mm Z-Axis Movement 115 mm The TRUMPF TruLaser 5030 (L56) fiber 5kW, manufactured in 2015, is a precise and efficient laser cutter. Its 3-axis system handles work dimensions of 3000 x 1500 x 115 mm. Powered by a 5000 Watt TruDisk 5000 fiber laser, it achieves high-speed cuts up to 265 m/min. The machine, measures 8800 x 4800 x 2400 mm. It is controlled by a Siemens Sinumerik 840 D for accuracy and ease of use. Contact us for more information about this machine. Application Types Cutting

Condition: used, Year of construction: 1989, Functionality: fully functional, FASTI 2040x3 folding machine with a wide range of accessories, including various upper and lower bending beams and various special bending tools. Fobswav Ahs Emy I Tegb Please refer to the images for technical specifications.

Condition: used, pressure 125 t chamfer lenght 3050 mm distance between columns 2550 mm ajustment speed 90.0 mm/sec working feed 10.0 mm/sec return speed 75.0 mm/sec stroke 140 mm dayligth 375 mm column arm 250 mm table width 90.0 mm work height max. ca. 950 mm Number of working hours 14.100 h total power requirement 13.5 kW weight 8500 kg range L-W-H 3630 x 2300 x 2505 mm From a maintenance workshop Good / well-maintained condition With only approx. 14.100 operating hours (!!) Equipment: - CNC electro-hydraulic press brake - DELEM CNC control - model "DA 58" * Swiveling control panel, front left * 2D graphic programming & product display * Tool & program library - CNC-controlled axes: * Y1+Y2 / X1+X2 / R1+R2 / Z1+Z2 / CNC crowning - CNC electro-motorized backgauge (X axes) * Stop system with 2x CNC-controlled gantries - CNC electro-motorized height adjustment of the backgauge (R axes) - CNC electro-motorized adjustment of the stop fingers (Z axes) - Manual upper tool clamping - Manual lower tool clamping - Various split upper and lower tools - 2x stable, movable Front support arms - 1x freely movable 2-hand/foot control - Side guard (swinging doors) - Rear guard (swinging door) Fgeb Emyjv Svals I Tob - Original operating instructions + control unit - Manufacturer's CE declaration

Condition: ready for operation (used), sheet thickness steel (max.): 6 mm, total height: 1,800 mm, total length: 3,480 mm, power: 75 kW (101.97 HP), workpiece length (max.): 3,100 mm, net weight: 6,200 kg, total depth: 1,500 mm, CNC Elgo backgauge Strokes/min: 12 > 32 str/min Backgauge: Elgo - 1000 mm Fob Emy Isv St H Ae Togb

Condition: used, Fasti 2095-32-2 folding machine In good condition Receive a completely new PLC control from the manufacturer Schröder-Fasti in 2022 Machine number: 95 295 020 operating voltage: 400V frequency: 50 Hz Control voltage: 230 V Connection power: 4,25 kW Rated current: 16.8A usable length: 3240 mm Sheet thickness: 2 mm Lift of the superstructure: 350 mm Adjustability of the lower and bending beams: 80 mm Fsb Eswavndsmy I Tegb Important NOTE: the machine got a new PLC control in 2022 Control brand: Schröder-Fasti Type: CFP120 Total weight: 6000 Installation dimensions: 4500x3000x2000 (mm) Operating hours: 4574

Condition: used, Year of construction: 1998, Laser cutting system Amada LC 2415 A2 Fsb Emov Stc Doy I Tjgb Year of manufacture: 1998 Laser power: 1.5 kW Control system: Fanuc Series 16l Travel ranges: X 2520 / Y 1550 / Z 300 mm Max. table load: 330 kg Overall dimensions (L x W x H): 450 x 250 x 230 cm Weight: 6800 kg The laser cutting system is currently still powered and can be demonstrated.

Year of construction: 2017, Condition: ready for operation (used), General Data Measurements width 2265 Measurements depth 4880 Measurements height 3230 Machine weight 28300 Main Drive Number of axis 6 Febev Svzie Emy I Tjgb Additional Equipment ByVision Bending operator terminal with 22 inch Full HD touchscreen OPC Interface Bending Bending curve generator Automatic kickstand suspension compensation by means of dynamic pressure reference Crown 4: Reactive hydraulically dynamic crowning of the lower cheek Automatic tool overload protection Compensation of the temperature-induced stator expansion Automatic dynamic pressure control with crowning 4 Material thickness measurement Fast Bend - safety system manually adjustable in height This 6-axis Bystronic Xpert 400/4100 press brake was manufactured in 2017. It offers precision bending with enhanced control and flexibility. Ideal for complex metal forming, this machine represents a significant asset for any fabrication setting. Contact us for more information about this machine. Application Types Bending

Condition: as good as new (ex-display), Year of construction: 2020, machine/vehicle number: 12999, Electroic servo break - 40t x 1300mm - ESA control (network-compatible) - 4 Axis (Y1, Y2, X, R,) - Save up to 50% Engergie - Highspeed bend 20mm/sec. - Precise bending 0.001mm Fgob Emy Ish Eip Ij Teb - No hydraulics = lower service costs

Condition: as good as new (ex-display), WEIKA 3200x10mm Guillotine Shear - Display machine / Unused - Cutting length 3200mm - Max. cutting thickness - steel 10mm - Max. cutting thickness - stainless steel 6mm - Max. cutting thickness - aluminum 12mm - Electric digital backgauge - Foot switch - Light barrier / right-left - Front support with ball transfer rollers - Drive power 11kW Dimensions: Fgjb Emy Iowatxgj Teb LxWxH 4x2x1.9 meters / Weight 8000kg Errors / input errors excepted

Condition: ready for operation (used), Elgo CNC controlled machine, very easy and user-friendly max tube cap: dia 76 mm x 4 mm thickness Feb Eov St Hpjmy I Tsgb max square tube: 70 x 70 mm max radius: 600 bending angle: 180° Standard tooling 3D Special tooling on request Length: 1200 mm Width: 800 mm Height: 1300 mm

Condition: excellent (used), Motorized Guillotine Shear (used) Manufacturer: RAS Model: 82.10 Max. cutting length: 1040 mm Max. sheet thickness for ST 40: 2.5 mm Distance between columns: 1040 mm Continuous hold-down clamp Backgauge travel: 5 – 500 mm Motor power: 2.8 kW Machine weight: 750 kg Fgeb Ejwardbomy I Tjb Space required: Depth: 2000 mm, Width: 1400 mm, Height: 1100 mm Foot switch Backgauge manually adjustable from the front Angle stop Support arms (front) The machine is in very good condition and ready for immediate use. Forklift available, truck loaded free Favourable shipping available Machine location: 48324 Sendenhorst

Condition: excellent (used), Year of construction: 2010, Functionality: fully functional, machine/vehicle number: 662210191, total height: 2,000 mm, overall weight: 1,300 kg, total width: 820 mm, total length: 1,380 mm, The DURMA P 55 hydraulic metal slotting machine was manufactured in 2010 by the renowned DURMAZLAR brand. Technical parameters: - table dimensions: 550x510 mm - reach: 510 mm Feb Esvb Ia Aemy I Tjgb - hole diameter fi 40 mm in 10 mm thickness - hole diameter fi 20 mm in 20 mm thickness - stroke: 60 mm - cycles per minute: 37 - engine power: 5.5 kW - tank capacity: 76 l - machine dimensions (length x width x height): 1340x1850x930 mm - machine weight: 1300 kg

Condition: good (used), Year of construction: 2012, Functionality: fully functional, For sale: 1 piece used hole punch Fgob Emy Ijuihvze Teb Manufacturer: Geka type: Puma 110 2HI Punching force: 110t incl. documentation Dimensions see type plate Machine can be inspected in our warehouse in 09599 Freiberg.

Condition: new, Year of construction: 2022, A compact design sheet fiber laser metal cutting machine with complete protection Small occupied space balances complete protection and higher safety. Each frame of the cutting machine bed is welded after mortise-and-tenon joint to achieve perfect mechanical property and better stability and firmness. The pull-out cutting machine table, with the electric table optional, saves space occupation and freshen up the user operation experience. Convenient and fast open&close with one click; The laser cutter door is safe and reliable, by using rack-pinion transmission mode combined with self-locking cutting machine system Fiber laser heads are able to detect jutting obstacles to effectively reduce the damage rate and save the maintenance cost of a laser cutter. Applicable Material: metal Condition: New Laser Type: Fiber Laser Febehwrg Ne Emy I Togb Laser Power: 1500W, 2000W, 3000W, 6000W, 12000W Cutting Area: 3048*1524mm Cutting Speed: 0-100m/min Positioning accuracy: ±0.05mm Repositioning accuracy: ±0.03mm Graphic Format Supported: AI, BMP, Dst, Dwg, DXF, DXP, LAS, PLT CNC or Not: Yes Cooling Mode: WATER COOLING

Condition: ready for operation (used), LVD PP 100/30 Fsb Emy Isv Skgyo Tjgb hydraulic press brake

Condition: ready for operation (used), total height: 3,000 mm, total length: 4,160 mm, throat depth: 330 mm, operating speed: 7 mm/s, retraction speed: 80 mm/s, travel distance Z-axis: 250 mm, controller manufacturer: 2D Touch, power: 18.7 kW (25.42 HP), net weight: 15,000 kg, opening height: 500 mm, passage width: 3,150 mm, total depth: 2,100 mm, 6 axes controlled: Y1 / Y2 / Z1 / Z2 / X / R / V (manual) -X-R-Z version with assymmetric fingerwidth - Manual bombation Systemtooling 2 plate supports Fiessler BendGuard Capacity: 250 ton x 3600 mm Backgauge: CNC Locking speed: 80 mm/sec Fsb Ejv St Exsmy I Togb

Condition: new, Year of construction: 2025, Technical specifications: Press force: 22 tons Bending capacity: 150 x 10 mm Stroke: 200 mm Tool height: 160 mm Table dimensions: 630 x 1100 mm Working height: 925 mm Motor power: 1.5 kW CE mark Dimensions (length x width x height): approx. 1200 x 950 x 950 mm Fgob Emyewamdco I Teb Weight: approx. 650 kg Accessories: 60° pressing tool Universal die 85°: V-16 – 22 – 35 – 50 The seller is not liable for typographical or data transmission errors.

Condition: ready for operation (used), Year of construction: 2005, Functionality: fully functional, total height: 4,320 mm, pressing force: 500 t, total width: 2,500 mm, total length: 10,000 mm, working length: 9,100 mm, power: 37 kW (50.31 HP), Model: PFO-PS Brand: F.lli Farina Year of Construction: 2005 Power: 500 Ton Control: CNC Delem DA65W Working hours: 3000 Fgeb Emy Iotv Nbns Teb CE certified Axes: Y1 - Y2 - X1 - X2 - R Register stroke: 800 mm Distance between uprights: 8000 mm Useful bending length: 9100 mm Adjustable stroke: 320 mm Swan neck: 500 mm Motor power: 37 kW

Condition: good (used), Year of construction: 2008, sheet thickness steel (max.): 4 mm, cutting length (max.): 1,530 mm, For sale: 1 piece used motorized guillotine shears Manufacturer: Schröder Model: MHSU 1500/4.0 YEAR OF MANUFACTURE: 2008 Effective length: 1.530mm Working height: 800mm Cutting capacity steel 400N/mm²: 4.0mm Mass: 940Kg Fsb Emy Iotumbyo Togb Incl. back gauge, sheet lifting device, light barriers, protective housing and documentation. The guillotine shear can be inspected in our warehouse in 09599 Freiberg.

Condition: new, Year of construction: 2024, Attention!! Special Offer!! Warranty inspection free of charge—only for Customers who have taken part in the demonstration at the machine showroom in Bydgoszcz. Hydraulic press brake PBO-2563-CNC OT-41 Specifications - Maximum bending thickness (S235): up to 4.0 mm - Nominal bending force: 630 kN - Maximum bending length: 2500 mm - Throat depth: 250 mm - Maximum stroke: 120 mm - Daylight: 370 mm - Distance between side frames: 2000 mm - Backgauge travel distance: 600 mm - Motor power output: 5.5 kW - Length: 2600 mm - Width: 1400 mm - Height: 2200 mm - Weight: 3700.0 kg Tools - Front supports: 2 pcs. - Backgauge drive (travel along the X-axis): servo motor - Ram drive (travel along the Y-axis): servo motor - Backgauge fingers positioning (R-axis): manual - Punch quick change tooling system form AMADA Otinus CNC OT-41 control The CNC controller Otinus is featured with convenient and intuitive menu. The software calculates the bending angle on its own. The large color touchscreen is readable from any angle. The controller can store up to 2,000 programs of 30 steps each. Fgebegi Dphs Emy I Teb Top quality components - Rexroth hydraulic valve - Schneider electrical components - Omron and Schneider safety circuit parts. - Steel hydraulic line tubings - Hydraulic lines made of steel instead of rubber reduce the risk of future leaks. Safety We attach great importance to the safety of our Clients and their employees; therefore our press brakes are equipped with visible safety labels, side guards, rear safety doors, easily accessible safety switches and light curtains that protect the operator against inserting their hands between the upper and lower dies. The machines comes with carefully prepared instructions manual. The machine has a CE marking and EU declaration of conformity. Oil cooling system The Oil Cooling System guarantees the stability of the machine's performance even after long, continuous operation. Assistance by a specialist We strive to maintain constant communication with our Customers. To support this, every machine purchase includes a specialist support package with hours of expert guidance. Within the service, our technicians may: - Specify the bending steps for intricate parts. - Advise on material and gas selection - Assist in the selection of operating parameters for different materials Included in the machine price 2-day training including installation of the machine - 1st day (up to 8 hours) - installation of the machine and learning to use the controller. - 2nd day (up to 8 hours) - independent work on the machine under the supervision of our technician with the possibility of programming specific parts manufactured by the Client. Telephone consultation with a specialist - 7.30 a.m. to 9 p.m. (Mon-Sat) - package of 8 hours to be used within 12 months - Free lending of transport rolls and two lifting jacks for easier positioning of the machine at Clients' facilities. The rollers and jack will be delivered after prior notification (no less than 7 days before delivery of the machine). Terms of cooperation - 24 month warranty - The machine is brand new - Warranty and post-warranty service provided by the seller - The Client is responsible for the machine during unloading and transporting on-site

Condition: good (used), Functionality: fully functional, machine/vehicle number: 804, sheet thickness steel (max.): 16 mm, sheet thickness (max.): 16 mm, overall weight: 12,500 kg, bending length: 2,500 mm, roller length: 2,550 mm, 3-roll bending machine 2500 x 16 mm Manufacturer: KUMLA Type: PV 7 H Number: 804, overhauled in 1987 The machine has a very sturdy construction and was only used for one shift. Max. bending length: 2500 mm Max. sheet thickness: 16 mm Conical bending device Top roll diameter: 324 mm Bottom roll diameter: 305 mm Fjbjvxbm Ro Emy I Tsgb Hydraulic roll adjustment Dimensions: L x W x H = 5000 x 1600 x H 1900 mm Working height: 1000 mm A step frame for the machine is also available for purchase.

Condition: good (used), Year of construction: 1991, machine/vehicle number: 0217 + 1285, Offer 23112 Technical specifications: - Motor-driven unit + travelling unit - Total load capacity approx. 5000 kg - Load capacity per container device approx. 2500 kg - Load capacity per wheel 1250 kg - Smallest tank diameter 300 mm - Largest tank diameter 3250 mm - Distance adjustment adjustable in increments - Roller diameter approx. 400 mm - Roller width 80 mm - Electric remote control Fgob Emewakufsy I Teb - Space requirement for driven unit approx. W 2000 x H 650 x D 450 mm - Space requirement for intermediate unit approx. W 1800 x H 450 x D 450 mm - Weight 450 kg

Condition: excellent (used), Year of construction: 2007, operating hours: 64,000 h, Functionality: fully functional, machine/vehicle number: 20306061, pressing force: 100 t, throat depth: 415 mm, distance between stands: 2,700 mm, bending length: 3,110 mm, stroke distance: 200 mm, Amada Astro II 100 NT bending cell. Fsb Emyowakice I Tjgb Includes loading robot, bending robot, repositioning device with extra support, loading table, conveyor for unloading pallets (currently disconnected), safety fence. Comes with multiple loading and bending grippers, both clamp and vacuum type. Worksheet loading both as stack or vertical loading unit. Bending force: 980kN Table length: 3110 mm Stroke: 200 mm Open height: 500 mm Worksheet thickness min: 0.6 mm Worksheet dimensions min: 150 x 150 mm Worksheet dimensions max: 800 x 1000 mm/ 300 x 1800 mm Worksheet mass max: 20 kg (including bending robot gripper/ loading robot gripper) Serviced by local Amada representative.

Condition: excellent (used), Year of construction: 1993, operating hours: 53,000 h, Functionality: fully functional, total height: 3,350 mm, pressing force: 160 t, bending length: 4,050 mm, throat depth of stand: 3,550 mm, stroke distance: 500 mm, For sale: 1 used hydraulic press brake Manufacturer: Weinbrenner type: GP160 YEAR OF MANUFACTURE: 1993 Pressing force: 1.600kN working length: 4.050mm Clear stand width: 3,550mm Stroke: 500mm Fsb Emork Aadey I Tjgb Control system: Cybelec Operating hours: 52,300 Incl. extensive tools, see contents blue shelf (shelf itself is not sold). Several folders of documentation available for the machine, Elt plans, Cybelec control,... Very well maintained condition. Machine can be inspected in our warehouse in 09599 Freiberg.