Auction

5

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical turning lathe

Gildemeister DMG CTV 250

€4,000

Condition: defective spare-parts repository (used), Year of construction: 2003, Functionality: not functional, TECHNICAL DETAILS Chuck diameter: 250 mm Face displacement stroke X: 800 mm Longitudinal stroke Z: 300 mm Rapid traverse speed X: 100 m/min Rapid traverse speed Z: 45 m/min Pymmrt9t0 Spindle head (flat flange): 170h5 mm Spindle diameter in front bearing: 120 mm Spindle bore: 79 mm Power of the three-phase mainlan drive: 22 kW Torque ED 100%: 210 Nm Speed range: 20 - 5000 rpm Speed range: 0-100 rpm Torque (holding torque brake): 240 Nm Accuracy of the point rest: < 0.02 degrees Number of tool stations: 12 Tool holder: according to DIN 69880 Cylindrical shank diameter: 40 mm Drive power (40% ED): 10.8 kW Torque: 28 Nm Speed: 6000 rpm Hydraulic capacity, complete: approx. 25 L Pressure: 80 bar Pressure for clamping device: 70 bar Cooling capacity: approx. 25 l Pump output: 1.7 kW Flow rate at 6 bar: 20 l/min Lubrication capacity: 1.8 l Rapid traverse speed Y: 10 m/min Feed force: 20000 N Hub: ±50 MACHINE DETAILS Net weight of the machine without chip conveyor: approx. 7500 kg Gross weight of the machine with truck transport: approx. 7800 kg Machine without chip conveyor L x W x H: approx. 2600 x 2200 x 2800 mm Total connected load: 50 kVA Voltage: 400 V Frequency: 50 Hz Fuse protection (slow-blow) according to VDE 0100: 80 A Permissible voltage fluctuation at 400 V: +/- 10% Machine acceptance: according to DIN 8605 Permissible ambient temperature: from +15 to +35°C Relative humidity: 75%. Installation altitude: 1000 m above sea level Fixed pick-up date of the machine on 27.12.23 or 09.12.23. Bidder is obliged to pick-up the machine on time.

more

Auction

8

Ends in

 d  Hrs  Min  Sec Auction ended

Tube bending machine with bar loader

BLM Dynam 0 MR200

€5,500

Condition: good (used), Year of construction: 2002, machine/vehicle number: 605030601009, Functionality: fully functional, TECHNICAL DETAILS Number of axes: 5 Average output: ~ 2400 bends/h Bending capacity round tube R=45 kg/mm²: 4 - 18 x 1.5 mm Bending capacity round tube R=35 kg/mm²: 4 - 20 x 1 mm Bending capacity round tube Al/Cu/Ms: 4 - 25.4 x 1.25 mm Bar feeder: BLM Carm 7 (BJ 2007) Positioning speed X-axis: 2000 mm/s Bh0d82cu7zu Bending speed H/Z Y-axis: 400 °/s Turning speed Z-axis: 900 °/s Turning speed Z-axis: 100 °/s Positioning speed T-axis: 500 mm/s Measuring tolerance X/T axis: ± 0.1 mm Measuring tolerance Y/Z/Q axis: ± 0.1° Maximum range at maximum acceleration X-Y-Z: 1000 mm - 90/90/0° - 0/180/0° with tube 18 x 1.25 mm MACHINE DETAILS Voltage: 380 V, 50 Hz Hydraulic pressure: max. 120 bar Machine weight: 1500 kg Control system: Cybelec DMC 80

more

Auction

9

Ends in

 d  Hrs  Min  Sec Auction ended

11-axis sliding headstock automatic lathe

STAR Micronis ECAS 32 T

€25,000

Condition: excellent (used), Year of construction: 2007, machine/vehicle number: 0179 (033), Functionality: fully functional, 11-axis sliding headstock automatic lathe from STAR in very good condition and with bar loader and bar magazine -> ready for immediate use! The bar feeder fills the bars automatically to the bar magazine FMB turbo 3-36. Machine is delivered with tool holders and spare parts. TECHNICAL DETAILS Number of axes: 11 Yfshh3ps Axes: X 1-3, Y 1-3, Z 1-3, C1-2 Turning diameter over bed: 32 mm Spindle clearance: 32 mm Turning length: 125 mm Control: YASKAWA SIEMENS 840 DI V2 Spindle speed: 7000 rpm Workpiece length: max. 150 mm Clamping diameter: 32 mm Feed rate: 0 - 2000 mm/min Bar feeder: available Bar magazine: FMB turbo 3-36 MACHINE DETAILS Machine weight: approx. 5.7 t Space requirement: approx. 10.5 x 2 x 1.9 m Supply voltage: 200 V, 3 phases Frequency: 50 / 60 Hz Connected load: 8.0 kVA

more

Auction

6

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical machining center

Hurco VMX24

€6,800

Condition: excellent (used), Year of construction: 2001, Functionality: fully functional, Machine interior repainted, covers new wipers TECHNICAL DETAILS x-path: 610 mm y-path: 508 mm z-path: 610 mm Speed range: max. 10000 rpm Control: UltiMax 4 Tool holder: SK 40 Tool positions: 24 (magazine) Table load: max. 1 t MACHINE DETAILS Machine weight: 5 t Wwcj2mpu Space requirement: 2.2 x 2.4 x 2.5 m

more

Auction

9

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical machining center

Mazak VARIAXIS i-700

€150,000

Condition: excellent (used), Year of construction: 2016, Operating hours: 9,760 h, Functionality: fully functional, 5-axis vertical machining center with simultaneous machining and comprehensive accessories - Gressel zero-point clamping system (5-axis vice), 100 tool holders and more! Machine was in use until the beginning of 2023 and has only 2,542 h of pure machining time - as good as new! Built in December 2016, but only commissioned in March 2018. TECHNICAL DETAILS X-axis: 630 mm Y-axis: 1,110 mm Z-axis: 600 mm A-axis: -120° - 30 ° C-axis: 360 ° Control: Smooth X, 5-axis simultaneous machining Table size: Ø 700 x 500 mm Table load: max. 700 kg Spindle speed: max. 18,000 rpm Rapid traverse X/Y/Z: 60/60/56 m/min Spindle motor: 35 kW Tool holder: HSK-63 Tool magazine: 40 tool positions Cooling system: IKZ MACHINE DETAILS Operating hours: 9760 h Machining time: 2542 h Dimensions: 2400 x 4121 x 3457 mm Weight: 15.5 tons EQUIPMENT Ljfqbebbnx Mayfran ConSep 2000 II chip conveyor with filter 70 bar high-pressure pump, 3 pressure stages Mazak Monitoring System B, Renishaw RMP measuring probe Removable handwheel Air through the spindle Air at the workpiece Coolant on the workpiece Synchronous thread cutting Program memory extension 32 MB Cylinder interpolation G07.1 Tool input compensation G54.1 Tool radius compensation 5-axis package for Smooth X Oil mist extraction 100 pieces HSK63 tool holder 1 piece zero point clamping plate, Gressel 1 piece 5-axis vice, Gressel

more

Auction

10

Ends in

 d  Hrs  Min  Sec Auction ended

Welding robot

IGM RTI330S

€20,000

Condition: excellent (used), Year of construction: 2013, Operating hours: 700 h, Functionality: fully functional, Commissioning 2014 TECHNICAL DETAILS Number of axles: 9 Dmwdth Arm radius: 1500 mm Working height: approx. 820 - 2500 mm Table: rotary tilting table Welding source: Fronius Extraction hood: Slide-on roof Functions: Gas nozzle search, seam search, extraction MACHINE DETAILS Height: 3041 mm Footprint: 4250 x 6250 mm

more

Auction

7

Ends in

 d  Hrs  Min  Sec Auction ended

CNC turning and grinding center

EMAG VSC 400 DDS

€8,000

Condition: excellent (used), Year of construction: 2002, Functionality: fully functional, TECHNICAL DETAILS Working range Diameter of the legs:  350 mm Rotation diameter:  360 mm X-trajectory:  725 mm Z-trajectory:  547 mm Y-trajectory:  307 mm Main spindle Spindle flange in accordance with DIN 55026:  size 8 Spinning bearings - Ø front:  120 mm Maximum speed:  6000 rpm Main drive AC motor 40% ID: 45 kW Maximum power:  58 kW Full power from spindle speed:  480 rpm Moment 40% ID:  480 Nm Maximum moment:  620 Nm Bijbuutlwsw Transport drive High speed X/Y/Z:  45/45/30 m/min Transport force in X/Y/Z:  5,5/11/11 KN Ball roller spindle in X/Y/Z:  40 mm Revolver star Intake cylinder shaft DIN 69880: 4 gang Shaft Ø: 40 mm Grinding spindle 1:  HSK C63, 9,000 rpm, 19 kW Grinding spindle 2:  HSK C32, 42,000 rpm, 7.5 kW hydr. Grinding spindle: 32,000 rpm, 0.9 kW Electrical equipment Operating voltage:  400 V Control voltage – DC:  24 V Control voltage – AC:  230 V Frequency:  50 Hz MACHINE DETAILS Length:  5,060 mm Width:  1,960 mm Height:  2,900 mm Weight:  12,000 kg Fixed pick-up date of the machine on 27.12.23 or 09.01.24. Bidder is obliged to pick-up the machine on time.

more

Auction

6

Ends in

 d  Hrs  Min  Sec Auction ended

Tube bending machines

BLM Dynam 0

€5,000

Condition: good (used), Year of construction: 1997, machine/vehicle number: 605970300001, Functionality: fully functional, TECHNICAL DETAILS Number of axes: 5 Average output: ~ 2400 bends/h Bending capacity round tube R=45 kg/mm²: 4 - 12.7 x 1.5 mm Bending capacity round tube R=35 kg/mm²: 4 - 14 x 1 mm Bending capacity round tube Al/Cu/Ms: 4 - 18 x 1.25 mm Bar feeder: BLM Carm 7 (year of manufacture: 2004) Positioning speed X-axis: 2000 mm/s Krf3faz Bending speed H/Z Y-axis: 500 °/s Turning speed Z-axis: 900 °/s Turning speed Z-axis: 100 °/s Positioning speed T-axis: 500 mm/s Measuring tolerance X/T axis: ± 0.1 mm Measuring tolerance Y/Z/Q axis: ± 0.1° Maximum range at maximum acceleration X-Y-Z: 1000 mm - 90/90/0° - 0/180/0° with tube 18 x 1.25 mm MACHINE DETAILS Voltage: 380 V, 50 Hz Hydraulic pressure: max. 120 bar Machine weight: 1500 kg Control system: DOC 85C

more

Auction

6

Ends in

 d  Hrs  Min  Sec Auction ended

Universal machining center

DMG DMU 60 monoBLOCK

€15,000

Condition: excellent (used), Year of construction: 2008, Functionality: fully functional, Machine including measuring probe TECHNICAL DETAILS X-path: 630 mm Y-path: 560 mm Z-path: 560 mm Number of axles: 4 pieces Control: Heidenhain MillPlus Table dimensions: 1000 x 600 mm Spindle speed: 12,000 rpm Rapid traverse: 30 m/min Tool changing device: 24-fold 3hnwdxp Spindle hours: approx. 12,500 h

more

Auction

13

Ends in

 d  Hrs  Min  Sec Auction ended

Gear hobbing machine

Liebherr LCV 180

€20,000

Condition: good (used), Year of construction: 2001, machine/vehicle number: 9600, Functionality: fully functional, No minimum price - guaranteed knockdown to the highest bidder! TECHNICAL DETAILS Bhwsrpnzzh0 Chuck diameter: 250 mm Circulation diameter: 265 mm x-path: 170 mm z-path: 200 mm Workpiece diameter: max. 180 mm Milling module: max. 3 mm Number of teeth: min. 4 Milling head swivel angle: ± 45° Resolution accuracy: 0.1° Spindle flange according to DIN 55026: 6 Front spindle bearing: Ø 100 mm Speed: 1500 mm Rapid traverse z-axis: 30 m/min MACHINE DETAILS Dimensions: 2950 x 1600 x 2360 mm Weight: 8000 kg Operating voltage: 400 V Frequency: 50 Hz Rated current: 45 A Ambient temperature: 15 - 38 °C Rel. humidity: max. 50/90 % at 40/20 °C Operating noise: 78 dB (A)

more

Auction

8

Ends in

 d  Hrs  Min  Sec Auction ended

Gear hobbing machine

Liebherr LCF 180

€5,000

Condition: good (used), Year of construction: 2000, Functionality: fully functional, Right of first refusal for the highest bidder: in the event of a knockdown, a higher number of items can be arranged No minimum price - guaranteed knockdown to the highest bidder! TECHNICAL DETAILS Chuck diameter: 250 mm Circulation diameter: 265 mm x-path: 170 mm z-path: 200 mm Workpiece diameter: max. 180 mm Milling module: max. 3 mm Number of teeth: min. 4 Milling head swivel angle: ± 45° Resolution accuracy: 0.1° Dmwc9r Spindle flange according to DIN 55026: 6 Front spindle bearing: Ø 100 mm Speed: 1500 mm Rapid traverse z-axis: 30 m/min MACHINE DETAILS Dimensions: 2950 x 1600 x 2360 mm Weight: 8000 kg Operating voltage: 400 V Frequency: 50 Hz Rated current: 45 A Ambient temperature: 15 - 38 °C Rel. humidity: max. 50/90 % at 40/20 °C Operating noise: 78 dB (A)

more

Auction

7

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical lathe

EMAG VSC 200

€5,000

Condition: good (used), Year of construction: 1997, Functionality: fully functional, Equipped with workpiece conveyor belt No minimum price - guaranteed knockdown to the highest bidder! TECHNICAL DETAILS Turning diameter: 260 mm turning length: 200 mm Dmwcpt Control: Siemens 840 C Spindle bore diameter: 50 mm Dimensions (L x W x H): 3,160 x 1,200 x 2,650 mm Machine weight: approx. 6,000 kg

more

Auction

3

Ends in

 d  Hrs  Min  Sec Auction ended

Laser engraving machine

Eutomation & Scansys

€12,000

Condition: excellent (used), Year of construction: 2016, Functionality: fully functional, TECHNICAL DETAILS Code reader:  SIEMENS MOBY E with profibus connection to the PLC for reading the code on the pallet Laser:  Trumpf TruMark 3020, 1064 nm Beam quality:  < 1,5 Pulse frequency:  1 kHz - 100 kHz Focus diameter:  30 µm with a focal length 100 mm Focus position control:  +/- 60 mm with focal length 330 mm Field size:  290 x 290 mm with focal length 330 mm Gu8bdu3hn Cooling:  Active air cooling (can be used up to 40°C) Code:   6-digit numeric code 2D-Code height:  approx. 8 x 8 mm Memory:  The code to be written is a 6 digit numeric code. The number of this code is written digitally 1 time and encoded 5 times 2D matrix on the circumference of approx. 70mm of the disc. The code itself is transmitted by the PLC to the laser. MACHINE DETAILS Laser dimenstion:  138 x 138 x 380 mm Supply unit dimensions:  445 x 465 x 420 mm Fixed pick-up date of the machine on 27.12.23 oder 09.01.24. Bidder is obliged to pick-up the machine on time.

more

Auction

16

Ends in

 d  Hrs  Min  Sec Auction ended

Two-spindle vertical lathe

EMAG VSC 200 DUO

€15,000

Condition: good (used), Year of construction: 1999, Functionality: fully functional, Right of first refusal for the highest bidder: in the event of a knockdown, a higher number of items can be arranged No minimum price - guaranteed knockdown to the highest bidder! TECHNICAL DETAILS X-path: 725 mm Z-path: 200 mm Chuck diameter: 160/200 mm Rotation diameter: 725 mm Bhwq9gdmrw8 Main spindle: 2 pieces Control: Siemens 840D Spindle flange (DIN 55026): 5 size Spindle bearing: 80 Ø - front Maximum speed: 6500 min-1 Spindle distance: 955 mm

more

Auction

14

Ends in

 d  Hrs  Min  Sec Auction ended

Gear shaping machine

Liebherr LS 82

€25,000

Condition: good (used), Year of construction: 1999, Functionality: fully functional, No minimum price - guaranteed knockdown to the highest bidder! TECHNICAL DETAILS Wheel diameter: max. 80 mm Wheel width: 44 mm Module: max. 5 Control: LIEBHERR Bhwq8ck9ows Stroke length: max. 55 mm Angle of inclination: max. 45 ° Tool diameter: 180 mm Dimensions (L x W x H): 4,200 x 2,600 x 2,600 mm Machine weight: approx. 8.5 t

more

Auction

18

Ends in

 d  Hrs  Min  Sec Auction ended

Tooth flank grinding machine

Liebherr LCS 182

€20,000

Condition: good (used), Year of construction: 2001, Functionality: fully functional, Right of first refusal for the highest bidder: a higher number of items can be arranged in the event of a knockdown No minimum price - guaranteed knockdown to the highest bidder! TECHNICAL DETAILS Wheel diameter: max. 180 mm Module: max. 5 Gkqt3bwnr Module: min. 1 Control: LIEBHERR Number of teeth: min. 7 Tool length: max. 210 mm MACHINE DETAILS Dimensions (L x W x H): 4,500 x 2,840 x 2,800 mm Machine weight: approx. 14 tons

more

Auction

14

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical lathe

EMAG VSC 200

€9,000

Condition: good (used), Year of construction: 1999, Functionality: fully functional, Right of first refusal for the highest bidder: a higher number of units can be procured in the event of a knockdown No minimum price - guaranteed knockdown to the highest bidder! TECHNICAL DETAILS Turning diameter: 260 mm turning length: 200 mm Control: Siemens Bhwqxuwufmn Spindle bore diameter: 50 mm Dimensions (L x W x H): 3,160 x 1,200 x 2,650 mm Machine weight: approx. 6,000 kg

more

Auction

12

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical machining center

Kitamura Mytrunnion-1

€16,000

Condition: good (used), Year of construction: 2007, machine/vehicle number: 15014, Functionality: fully functional, TECHNICAL DETAILS X-axis: 325 mm Y-axis: 510 mm Z-axis: 460 mm A-axis: 140° (-110° to +30°) C-axis: 360° Speed: 150 - 15,000 rpm Control: Fanuc 300i Tool positions: 60 Tool holder: BBT30 Tool diameter x length: 60 x 200 mm Tool weight: max. 2 kg Table size: 120 mm MACHINE DETAILS Footprint: 2189 x 3122 mm Height: 3119 mm Weight: 6850 kg Bhhcishgmxc EQUIPMENT Chip conveyor double-deck type with filter system Cooling through the spindle Nurbs interpolation High-precision contour control with 64-bit Risc processor High-speed machining with 2,500 blocks/second The control reads 600 blocks in advance 16 MB data server Nano interpolation: Positioning command to the server from the control is calculated in nanometers 5-axis programming support: tool center point machining for 5-axis machining + tool radius compensation for 5-axis machining Spatial movement of the coordinate system for 5-axis machining

more

Auction

9

Ends in

 d  Hrs  Min  Sec Auction ended

Lathe with superfinishing device

DMG MORI CTX alpha 500

€28,000

Condition: excellent (used), Year of construction: 2017, Operating hours: 2,947 h, machine/vehicle number: 0040001262C, Functionality: fully functional, 2-axis universal lathe modified with SUPFINA mod. 202 superfinishing device without superfinishing belt and with intermediate interface in the X-axis TECHNICAL DETAILS Swing diameter over guide way protection:  500 mm Clamping chuck diameter:  170 (210) mm Transverse stroke (X axis):  190 mm Longitudinal stroke (Z axis):  525 mm Control:  SIEMENS SINUMERIK 840D solutionline operation with CELOS und ShopTurn 3G, Linux operating system. Rapid feed, X/Z axes:  30/30 m/min Y axis:  22.5 m/min Spindle nose size:  140 h5 mm Spindle diameter in front bearing:  100 mm  Spindle bore diameter: 73 mm AC main drive power (100 % - 40 % ED):  13 - 14 kW Torque (100% - 40% ED):  171.5 - 192 Nm Speed range:  20 - 6000 rpm MACHINE DETAILS Electrical connection:  5 conductor system, L1, L2, L3, N, PE Connected load:  total approx. 30 kVA Voltage:  400 V Frequency:  50 Hz Protection (slow-blow) acc. to VDE 0100: 63 A Permissible voltage fluctuation:  at 400 V: ±10 % Bhwvef3cyds Dimensions without chip conveyor L x W x H:  approx. 3330 x 2583 x 1829 mm Weight:  approx.. 4400 kg Fixed pick-up date of the machine on 27.12.23 or 09.01.24. Bidder is obliged to pick-up the machine on time.

more

Auction

15

Ends in

 d  Hrs  Min  Sec Auction ended

3-axis vertical machining center

Deckel Maho DMP 45 V Basic

€16,500

Condition: new, Year of construction: 2006, Operating hours: 0 h, machine/vehicle number: 15225450054, Functionality: fully functional, Cover Maho DMP 45 V linear Basic - 100% mechanical / 95% electrical finished as part dispenser or for prefabrication Last modernized with parts in 2016 and maintained to this day - unused Highlights: - unrivalled chip-to-chip time of 1.8 s thanks to modified double gripper principle (synchronized stroke and rotary movement) - Guaranteed shortest tool change times - workpiece change in 3 s thanks to 180° swivel/changing table - generously dimensioned machine bed - Compact machine design - maximum precision and quality due to high rigidity and vibration stability thanks to traveling column design - Linear drive for maximum productivity TECHNICAL DETAILS Travel X / Y / Z: 450 / 270 / 280 mm Option package 4th axis: NZ; dividing head and counter bearing Center height: 130 mm from FTW (provision without servo motor) Accuracy: 0.008 mm Feed rate: 1 - 15,000 mm/min Rapid traverse X / Y / Z: 80 / 72 / 72 m/min Control: Siemens 840 D Powerline Table: 2 pcs. 660 x 300 mm Workpiece weight: max. 200 kg Table changeover time: 3 s Spindle speed: 20 - 18,000 rpm Torque: 40.5 Nm Tool holder: HSK-A40 Tool length: 180 mm Chip-to-chip time: 1.8 s MACHINE DETAILS Weight: approx. 6500 kg Installation dimensions: 4065 x 3280 x 2466 mm Transport dimensions: 4065 x 1845 x 2412 mm Voltage: 400 V 3-phase / 230 V 50 Hz Control voltage: 24 V Power consumption: 50 kVA Compressed air: 6 bar Cooling liquid: 200 l Cooling flow rate: 40 l/min Pressure: 2.5 bar Bhhax8rmzwy Internal cooling: IKZ through spindle Internal cooling liquid: 600 l Internal cooling flow rate: 23 l/min Pressure: 40 bar EQUIPMENT - Chip conveyor - Coolant tank

more

Auction

10

Ends in

 d  Hrs  Min  Sec Auction ended

Milling machine - as good as new

Millstar VH 450

€19,000

Condition: new, Year of construction: 2021, machine/vehicle number: GM16080202201, Functionality: fully functional, HIGHLIGHTS Very stable machine construction made of gray cast iron with hardened flat guides in the X Y Z axes Conventional control with digital display Linear measuring systems in the X Y Z axes Stepless feed of the axes X Y Z 2-stage gearbox for the main spindle drive - infinitely variable Vertical and horizontal work spindle - BT 50 - manual tool clamping TECHNICAL DETAILS X-axis: 1,100 mm Y-axis: 720 mm Z-axis: 780 mm Speed: 1,600 rpm Cone spindle: BT 50 Milling table clamping surface: 1,500 x 450 mm Workpiece weight: 1,000 kg Number of T-slots: 5 T-slots: 18 mm Feed rate: 25 - 1,500 mm/min Rapid traverse: max. 6,000 mm/min MACHINE DETAILS Motor power: 7.5 kW Machine weight: 4,200 kg Space requirement: 3.5 x 3.1 x 2.75 mm EQUIPMENT Gkgmb0oed Control panel Electronic handwheel for the X Y Z axes Central lubrication system - bed track lubrication - automatic Coolant device Chip guard and splash guard mounted on the milling table CE marking Documentation in English

more

Auction

3

Ends in

 d  Hrs  Min  Sec Auction ended

Lathe

Benzinger TNI B8

€15,000

Condition: repair required (used), Year of construction: 2000, Functionality: not functional, Error: Machine starts up, but the axis module of the Y-axis reports an error Special feature: the main spindle is a special spindle (71916 with short taper 5 holder and a special cylinder 4371 made by Röhm) TECHNICAL DETAILS Control: 2-channel Siemens 840 D, Turret 1: X1-, Z1- and Y1-axis Lvm7msblir Counter spindle: X2-, Z2- and Y1-axis Tool positions turret: 1x 12-fold pneumatic Tool positions counter spindle: 1x 12-fold pneumatic Holder: VDI25 with single-position drive Additional counter spindle tool positions: Spindle turret around the counter spindle with 7 VDI 16 positions Main spindle belt drive: Pneumatic hollow clamping cylinder D42 Counter spindle belt drive: pneumatic hollow clamping cylinder Unloading device: with unloading belt Coolant system: with heat exchanger Chip collection container: available

more

Auction

7

Ends in

 d  Hrs  Min  Sec Auction ended

C-Y-axis lathe

DMG MORI CTX alpha 500

€60,000

Condition: excellent (used), Year of construction: 2008, Operating hours: 355 h, machine/vehicle number: 0045000018C, Functionality: fully functional, No minimum price - the highest bid is guaranteed to win! Biizviz2wna The machine is in a vocational school and has hardly been used - very few spindle hours! TECHNICAL DETAILS Turning length: 500 mm Y-axis stroke: ±40 mm (for cross slide) Speed: 6000 rpm C-axis: available Disk turret: Sauter 12-fold VDI 30 (driven) CNC control: Siemens 840D solutionline with ERGOline Programs: DMG MACHINEcheck, DMG AUTOshutdown and ShopTurn Drive power (100/40 % ED): 20/27 kW Drawtube inner diameter: 52 mm MACHINE DETAILS Connected load: 25 kVA Operating voltage: 400 V EQUIPMENT Tailstock Spindle brake Chip conveyor with coolant device Coolant spray gun Three-jaw power chuck with BBD 210/66 bore (made by SMW-Autoblock) Bar gripper, axial, complete, VDI 30 Workpiece pick-up device with automatic gripper arm, conveyor belt, protective flap

more

Auction

8

Ends in

 d  Hrs  Min  Sec Auction ended

Horizontal machining center

Matsuura MAM 600HG PC-8

€12,000

Condition: good (used), Year of construction: 1999, Functionality: fully functional, Machine is equipped with 8 pallets and 4 axes. TECHNICAL DETAILS Travel X/Y/Z: 600/600/6250mm B-axis: 0.001º Rapid traverse X/Y/Z: 24 m/min Feed X/Y/Z: 10 m/min Spindle speed: 30-10,000 rpm Control: Yasnac J300 Pallets: 8 pieces, 400 x 400 mm Spindle bearing diameter: 80mm Spindle power: 22/15KW Bhhbwwau3rc Mounting: BT 40 taper EQUIPMENT - 240 tools prepared - Paper belt filter - Chip conveyor - IKZ 50 bar - Blum laser tool monitoring - many control options: e.g. Advanced Zee-Lag G function

more

Auction

6

Ends in

 d  Hrs  Min  Sec Auction ended

Lathe

DMG MORI ecoTurn 450

€24,000

Condition: excellent (used), Year of construction: 2015, Operating hours: 13,115 h, machine/vehicle number: 0031000209A, Functionality: fully functional, TECHNICAL DETAILS Swivel range: max. 650 mm Movement via cross slide: 465 mm Turning diameter: max. 400 mm Transverse travel (X): 267.5 mm Longitudinal travel (Z): 600 mm Maximum speed: 4000 rpm Ljew3o0nvj Controls: SIMline with operation on SIEMENS 840D solution line Rapid traverse (X/Z): 30/30 m/min Spindle head (flat flange): 170 h5 mm Bar capacity: Ø 65 / 75 mm Spindle diameter in front bearing: 130 mm Drill chuck: 250/315 Drive power (40/100% ED): 17.5 / 12.5 kW Maximum torque (40/100% ED): 370 / 280 Nm According to ISO 230-2 in X/Z axes (indirect measuring system): 8/8 μm According to ISO 230-2 for C-axis: 20 μm Number of tool positions: 12 Driven tool stations: 12 Shank diameter: 40 mm Drive power (40% ED) at 2000 rpm: 4.2 kW Maximum torque (40% ED): 20 Nm Maximum speed: 4000 rpm MACHINE DETAILS Weight: 5800 kg Fixed pick-up date of the machine on 27.12.23 or 09.01.24. The bidder is obliged to pick up the machine on time.

more

Auction

15

Ends in

 d  Hrs  Min  Sec Auction ended

3-axis vertical machining center

Deckel Maho DMP 45 V linear High-End

€15,000

Condition: like new (used), Year of construction: 2006, Operating hours: 5,214 h, machine/vehicle number: 15225460024, Functionality: fully functional, Maho DMP 45 V linear high-end cover - 100% finished and ready for use after commissioning routine for longer service life Last modernized with parts in 2016 and maintained to this day - few operating hours Highlights: - unrivalled chip-to-chip time of 1.8 s thanks to modified double gripper principle (synchronized stroke and rotary movement) - Guaranteed shortest tool change times - workpiece change in 3 s thanks to 180° swivel/changing table - generously dimensioned machine bed - Compact machine design - maximum precision and quality due to high rigidity and vibration stability thanks to traveling column design - Linear drive for maximum productivity TECHNICAL DETAILS Travel X / Y / Z: 450 / 270 / 280 mm Option package 4th axis: NZ; dividing head and counter bearing Center height: 130 mm from FTW (provision without servo motor) Accuracy: 0.008 mm Feed rate: 1 - 15,000 mm/min Rapid traverse X / Y / Z: 80 / 72 / 72 m/min Control: Siemens 840 D Powerline Table: 2 pcs. 660 x 300 mm Workpiece weight: max. 200 kg Table changeover time: 3 s Spindle speed: 20 - 22,000 rpm Torque: 40.5 Nm Tool holder: HSK-40E Tool length: 180 mm Chip-to-chip time: 1.8 s MACHINE DETAILS Weight: approx. 6500 kg Installation dimensions: 4065 x 3280 x 2466 mm Transport dimensions: 4065 x 1845 x 2412 mm Voltage: 400 V 3-phase / 230 V 50 Hz Control voltage: 24 V Power consumption: 50 kVA Compressed air: 6 bar Cooling liquid: 200 l Cooling flow rate: 40 l/min Krfvx8j Pressure: 2.5 bar Internal cooling: IKZ through spindle Internal cooling liquid: 600 l Internal cooling flow rate: 23 l/min Pressure: 40 bar EQUIPMENT - 1 table - divided into set-up room and work area side - INTERLIT 600 l IKZ system - Chip conveyor - INTERLIT 600 l paper belt filter system - Special equipment 2 x dividing head and 2 x counter bearing, spare motor spindle

more

Auction

12

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical machining center

Samsung SMEC LCV 380 S

€19,000

Condition: as good as new (ex-display), Year of construction: 2015, Operating hours: 989 h, machine/vehicle number: 15L390029, Functionality: fully functional, TECHNICAL DETAILS X-path: 520 mm Y-path: 380 mm Z-path: 350 mm Spindle speed: max. 12,000 rpm Control name: FANUC OI-MF Table load: max. 300 kg Clamping surface: 600 x 570 mm Rapid traverse: 36 / 36 / 30 m/min Feed rate: 1 - 20,000 mm/min Drive power: 7.5 / 5.5 kW Number of tool magazine positions: 20 Tool holder: BT30 Tool change time: 0.85 sec Chip to chip: 2.2 s Dm0hkh MACHINE DETAILS Internal cooling: 20 bar Machine weight: 4000 kg Dimensions L x W x H: 2800 x 2500 x 2500 mm Operating hours: 989 h

more

Auction

8

Ends in

 d  Hrs  Min  Sec Auction ended

Band saw machine

Kaltenbach KBR 371NA

€3,000

Condition: good (used), Year of construction: 2002, machine/vehicle number: 122590, Functionality: fully functional, TECHNICAL DETAILS Cutting range 90° round: 400 mm Square: 371 x 371 mm square: 400 x 370 mm Saw blade: 5,920 x 34 x 1.1 mm ( 5,920 x 41 x 1.3 mm) Feed: 10 to 760 mm multiple times MACHINE DETAILS Connection: 9.2 kW Weight: 4.2 tons Bicxl2pn2oz Dimensions: 4,000 x 2,200 x 1,850 mm

more

Auction

16

Ends in

 d  Hrs  Min  Sec Auction ended

5-axis universal machining center

DMG MORI DMU 65 monoBLOCK

€115,000

Condition: good (used), Year of construction: 2014, Operating hours: 57,846 h, machine/vehicle number: 12140011573, Functionality: fully functional, No minimum price - the highest bid is guaranteed to win! Spindle replaced at 45,000 h in June 2022 Machine interface for automation available TECHNICAL DETAILS X axis: 735 mm Y axis: 650 mm Z axis: 560 mm B axis: +120° / -120° C axis: 360 ° Control: Heidenhain ITNC 530 3-D Speed: 10,000 rpm Tool magazine: Vertical chain magazine with 120 pockets Tool holder: HSK-A63 Measuring probe: Heidenhain TS 649 Biix2xazljw Table load: 1,000 kg T-slot table top C-axis: 1 x 14 H7 (alignment slot); 8 x 14 H12 (clamping slots); Drilling pattern: 8 x M12 Spindle power (40% ED): 46 kW Torque (40% ED): 200 Nm MACHINE DETAILS Weight: 12.7 t Operating time: 67408 h Processing time: 57846 h Supply voltage: 400 V / 50 Hz Connected load: 53 kVA EQUIPMENT Chip conveyor (scraper belt) Blum laser tool measurement MPC IKZ 40 BAR Paper belt filter Rotating viewing window Flushing gun with pump Oil mist separator Electric handwheel iTNC 530 ATC - programmable feed rate parameter setting for machining task Active chatter suppression ACC Safety package for power failure Infrared touch probe, Heidenhain TS 649 3D quickSET extension package MPC machine protection through quick shutdown Documentation in German

more

Auction

17

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical machining center

Matec 30HV

€12,000

Condition: good (used), Year of construction: 2001, Operating hours: 63,953 h, machine/vehicle number: 0363, Functionality: fully functional, Large vertical machining center with 4 axes TECHNICAL DETAILS X-axis: 4,000mm Y-axis: 800mm Z-axis: 1,000mm B-axis: 1 degree swivel Spindle speed: 12,000min Vw0a0zz Control: Heidenhain TNC 430 iTNC Tool holder: SK 40 Number of magazine positions: 48 MACHINE DETAILS Switch-on time control: 11342 h Machine switch-on time: 63953 h Program run: 30055 h Installation volume: 8.17 x 536 x 4.50 m Operating voltage: 400 V Connected load: 42 kW Transport length: approx. 6780 mm Transport width: approx. 3120 mm Transport height: approx. 3200 mm

more

Auction

8

Ends in

 d  Hrs  Min  Sec Auction ended

Internal and surface grinding machine

Buderus CNC 235 IA-T-L

€60,000

Condition: excellent (used), Year of construction: 2017, machine/vehicle number: 9469, Functionality: fully functional, TECHNICAL DETAILS Largest workpiece diameter:  150 mm Max. Workpiece diameter:  250 mm Maximum workpiece length:  350 mm Largest swivelling diameter above the table:  310 mm Height of the workpiece spindle above the floor:  1150 mm Workpiece spindle speeds:  0 - 3000 rpm (NC-programmable) Control:  Siemens SINUMERIK 840D SL Z-axes:  885 mm X-axes:  300 mm Rapid traverse Z-Achsen:  0 - 60 m / min Rapid traverse X-Achsen:  0 - 30 m / min Infeed speed infinitely variable:  0.01 - 15 mm / min Infeed depending on the stroke:  0.0005 - 0.1 mm Workpiece spindle positioning:  C-axis Bhwtt2emn2l MACHINE DETAILS Connected load of the machine:  approx. 45 kW Weight:  16500 kg Fixed pick-up date of the machine on 27.12.23 or 09.01.24. Bidder is obliged to pick-up the machine on time.

more

Auction

35

Ends in

 d  Hrs  Min  Sec Auction ended

3-axis vertical machining center

Deckel Maho DMP 60 V linear

€15,000

Condition: reconditioned (used), Year of construction: 2016, Operating hours: 9,874 h, machine/vehicle number: 560028, Functionality: limited functionality, Vertical machining center from Deckel Maho's special series: Deckel Maho DMP 60 V linear - high-end milling with preparation for automation solution (robot interface, unmanned production) Built in 2002 and last modernized with parts in 2016 and maintained to this day - few operating hours Functionality: conditionally functional, due to the development of an automation solution Automation: - Robot loading - the two rear cabin parts were removed to accommodate the cladding elements of the robot cell - Wiring simulated with Euchner safety switches - the cable ducts in the switch cabinet are open Highlights: - unrivalled chip-to-chip time of 1.8 s thanks to synchronized stroke and rotary movement - Shortest tool change times - workpiece change in 3 s thanks to 180° swivel/changing table - maximum precision and quality due to high rigidity and vibration stability thanks to traveling column design - Linear drive for maximum productivity TECHNICAL DETAILS Travel X / Y / Z: 600 / 400 / 425 mm Option package 4th axis: NC dividing head + counter bearing Center height: 160 mm from FTW (provided without servo motor) Feed rate: 1 - 20,000 mm/min Rapid traverse X / Y / Z: 80 / 65 /65 m/min Bhhavfemcf0 Control: Siemens 840 D Powerline Table: 2 pcs. 660 x 400 mm Workpiece weight: max. 300 kg Table changeover time: 3 s Spindle speed: 20 - 18,000 rpm Torque: 130 Nm Tool holder: HSK-A63 Tool length: 250 mm Chip-to-chip time: 1.8 s MACHINE DETAILS Voltage: 400 V 3-phase / 230 V 50 Hz Control voltage: 24 V Power consumption: 50 kVA Cooling liquid: 200 l Cooling flow rate: 40 l/min Internal cooling: IKZ through spindle Internal cooling liquid: 600 l Internal cooling flow rate: 23 l/min EQUIPMENT - 1 table, set-up area and work area side - INTERLIT 900 l IKZ system (high pressure with 40/80 bar pump and pump circuits, spray gun, level compensation pump, near-spindle chip flushing, IKZ) - Chip conveyor - INTERLIT 600 l paper belt filter system - Robot base as a connection to the machine bed - 2x precision dividing heads from FTW, center height 160 mm with counter bearing without servo motor - Workpiece palletizing (1x removal, 1x deposit) - Headstock with Kessler spindle according to DMG service - used compact filter system / 3 x chip conveyor IKF400 -Special equipment: headstock, compact filter system, tool magazines, spare parts, robot cladding

more

Auction

7

Ends in

 d  Hrs  Min  Sec Auction ended

Universal machining center

TOS KURIM FSQ 100

€50,250

Condition: excellent (used), Year of construction: 2001, Functionality: fully functional, TOS KURIM FSQ 100 Universal BAZ with HEIDENHAIN TNC 426 control TECHNICAL DETAILS X-path: 1,600 mm Y-path: 1,000 mm Z-path: 780 mm WORKING RANGE -CUBIC - Number of machining axes (without parallel axes) 5 - X-axis travel: 1,600 mm - Y-axis travel: 1,000 mm - Z-axis travel: 780 mm TABLE - Clamping surface (left-right): 1,000 mm - Clamping surface (front-rear): 1,000 mm - Workpiece weight (max): 6,000 kg - Rotation axis: C > Positionability 0.001 ° Dmxiib MILLING SPINDLE / HEAD - Spindle type: Swivel head > Positionability 2.5 ° - Speed range: up to 2,500 /min - Tool holder: ISO SK 50 - Drive power: 22 kW TOOL MAGAZINE - Number of tool positions 60 WORKPIECE AUTOMATION - Number of storage locations: 2 - Pallet length: 1,000 mm - Pallet width: 1,000 mm - Number of pallets: 2 DIMENSIONS / WEIGHTS - Space requirement (left/right): 6,400 mm - Space requirement (front/rear): 6,900 mm - Total height: 4,000 mm - Total weight approx. 26,000 kg Control HEIDENHAIN TNC 426

more

Auction

12

Ends in

 d  Hrs  Min  Sec Auction ended

Cylindrical grinding machine

KELLENBERGER KEL-VARIA UR 175/1000

€20,000

Condition: excellent (used), Year of construction: 2004, machine/vehicle number: 650542, Functionality: fully functional, The workpiece spindle and tailstock were replaced in 2022 and the machine was completely overhauled by Kellenberger - cost calculation of approx. 50,000 euros is available. TECHNICAL DETAILS Control: Heidenhain Center width: 1,000 mm Table travel: 1,150 mm Center height: 175 mm Rotation diameter: 350 mm Swivel range: -10° to + 100° Speed: 8 to 800 rpm infinitely variable S9torh03 Work weight between centers: 150 kg Table feed: 1 - 394 mm/min Table speed: max. 15 m/min Grinding wheels left: 500 x 80 x 203.2 mm Sanding headstock: fixed base frame, cannot be swiveled Micro-adjustment with correction range: 150 μm Tailstock holder: MK 5 Quill stroke: 50 mm MACHINE DETAILS Weight: approx. 6 tons Dimensions: 4,000 x 2,300 x 2,200 mm Connection: approx. 10 kW Supply voltage: 400 V EQUIPMENT Paper filter Full enclosure Sanding mist extraction Cooling unit

more

Auction

13

Ends in

 d  Hrs  Min  Sec Auction ended

5-axis horizontal machining center

Deckel Maho DMC 80 H

€145,000

Condition: good (used), Year of construction: 2013, Operating hours: 43,419 h, machine/vehicle number: 1222 0000033, Functionality: fully functional, No minimum price - the highest bid is guaranteed to win! Machine in a more powerful version and with comprehensive accessories TECHNICAL DETAILS Travel: 800 x 1,095 x 1,050 mm Rotation B-axis: 360 Swivel range A-axis: 25° / - 200° Speed: 18,000 rpm Control: Siemens 840D solutionline Operate Table load: 600 kg Tool holder: HSK-A63 according to DIN69893 Tool clamping: hydromechanical Tool changer: Double gripper Tool magazine: Wheel magazine, 123 places HSK-A63 Rotary table: NC with pallet carrier Pallet size: 2 x 630 x 630 mm T-slot clamping surface: DIN55201 - A2 T-slots: 14 mm Motor spindle power (40% / 100% ED): 34 / 28 kW Gkrrv7mh2 Torque (40% / 100% ED): 110 / 84 NM MACHINE DETAILS Switch-on time: 57,876 h Operating hours: 43,419 h EQUIPMENT Horizontal milling head Rotary pallet changer 3D path control Control language: German Clamping hydraulics 2/4 for work table and set-up station Preparation of hydraulic connection 2/4 for additional pallet Cone cleaning station with rotating brushes for HSK tool holder Tool magazine Wheel magazine (2 wheels) Tool breakage control MPC - machine protection through quick shutdown Signal lamp in 4 colors (red, yellow, green, blue) Rotating viewing window Work area door Flushing gun with pump Oil and emulsion mist separator MCIS_TDI tool management system Siemens 840D electronic handwheel Complete documentation, German

more

Auction

5

Ends in

 d  Hrs  Min  Sec Auction ended

Lathe

FAT Haco FTM165

€70,000

Condition: as good as new (ex-display), Year of construction: 2018, machine/vehicle number: 170803, Functionality: fully functional, Power - Precision - Performance This machine model is the most compact model from FAT Haco in the field of turning and milling centers. The machine has only been used a little and is therefore in mint condition! Gpewoivph Including parts catcher for main and counter spindle and tool. TECHNICAL DETAILS Spindle distance: 1000 mm Turning diameter over bed: 550 mm Turning diameter: 350 Speed: 6000 rpm Control system: Siemens 840 D SL Y-axis: ± 35 mm Longitudinal travel: 210 mm Rapid traverse X/Z: 35 m/min Torque: 275 Nm Spindle nose according to DIN 55026: A2-6 Spindle taper: 1:20 Counter spindle speed: 6000 rpm Counter spindle rapid traverse: 30 m/min Counter spindle torque: 95 Nm Counter spindle nose: A2-6 Tool holder: VDI 40 Tool positions: 12 Tool holder diameter: 20 mm Index time: 0.2 s Speed: 4000 rpm Quill taper: MT 4 Traversing method: automatic positioning Diameter of quill: 55 mm Tailstock stroke: 15 mm Thrust force: 4,400 N MACHINE DETAILS Dimensions: 1940 x 1860 x 3750 mm Weight: 6600 kg Power: 57 kW

more

Auction

10

Ends in

 d  Hrs  Min  Sec Auction ended

Internal and surface grinding machine

Buderus CNC 235 MA

€90,000

Condition: excellent (used), Year of construction: 2018, machine/vehicle number: 9473, Functionality: fully functional, TECHNICAL DETAILS Largest workpiece diameter:  150 mm Max. Workpiece diameter:  280 mm Largest swivelling diameter above the table:  200 mm Height of the workpiece spindle above the floor:  1250 mm Workpiece spindle speeds:  NC-programmable Control:  Siemens SINUMERIK 840D Z-Axis 1: 600 mm Z-Axis 2: 400 mm Z-Axis 3: 400 mm X-Axis 1: 280 mm X-Axis 2: 280 mm X-Axis 3: 280 mm Rapid traverse Z-Achsen:  0 - 30 m / min Rapid traverse X-Achsen:  0 - 30 m / min Infeed speed infinitely variable:  0.01 - 15 mm / min Bhwtr3rvqsw Infeed depending on the stroke:  0.0005 - 0.1 mm Workpiece spindle positioning:  C-axis MACHINE DETAILS Connected load of the machine:  approx. 50 kW Weight:  9000 kg Fixed pick-up date of the machine on 27.12.23 or 09.01.24. Bidder is obliged to pick-up the machine on time.

more

Auction

12

Ends in

 d  Hrs  Min  Sec Auction ended

Laser cutting machine

Deckel Maho DML 40 SI

€10,000

Condition: excellent (used), Year of construction: 2003, Operating hours: 1,930 h, machine/vehicle number: 11150001077, Functionality: fully functional, DML 40 SI laser machine with filter unit and laser cooler Comprehensive maintenance last carried out in 2020. TECHNICAL DETAILS x-axis: 400mm y-axis: 300mm z-axis: 500mm Load of the table: max. 50kg Laser class: 4 Wavelength: 1064 μm Nominal power: 100 W cw with 4 mm aperture MACHINE DETAILS Nominal power: 27 kVA Laser operating hours: 1046h Machine operating hours: 1930h Machine dimensions: 2.30 x 1.40 x 195 m Bilqmzwc8ak Filter unit dimensions: 0.66 x 0.36 x 1.38 m Laser cooler dimensions: 0.85 x 0.55 x 1.02 m Weight of machine: 2560 kg Weight filter unit: 82 kg Weight laser cooler: 185 kg EQUIPMENT Laser cooling with Termochiller P607 Filter unit type MKF LC1(year 2003) Lasersoft 3D software

more

Auction

4

Ends in

 d  Hrs  Min  Sec Auction ended

Tube bending machines

Hirschmiller und Höhn NCB 4000

€10,000

Condition: used, Year of construction: 1997, Functionality: fully functional, Contrary to the provision described above, the machine is provided EXW free loaded Dm3v9n DESCRIPTION Fully automatic, numerically controlled machine For bending hydraulic lines and car brake lines of various lengths. Variable number of bends possible 2 different, independent bending modules. Each module has 2 NC axes with program memory for Program memory for 250 lines the loading unit consists of a manually fillable drum magazine Loading takes place by means of an insertion swivel arm TECHNICAL DETAILS Tube diameter: 4.75 - 8.0 mm Bending angle: max. 180 ° Travel speed: max. 2.0 m/s Max. Max. number of bends: 100 per tube Functions: "Longitudinal bending" (axis 1 + axis 3), "Turning the bending head" and "Bending" (axis 2 + axis 4) Control unit: Bundy GHF 60134 Drum magazine capacity: 500 - 1000 pieces MACHINE DETAILS Compressed air: min. 4.5 bar Total power requirement: approx. 10 kW Machine weight: 6.0 t Machine dimensions: 6.3 x 3.7 x 2.0 m Control cabinet dimensions: 1.8 x 0.5 x 2.7 m Control panel dimensions: 0.85 x 0.68 x 1.65 m EQUIPMENT Various individual and add-on parts

more

Auction

6

Ends in

 d  Hrs  Min  Sec Auction ended

Vertical lathe

Titan Umaro SC 43 - F01

€90,000

Condition: refurbished (used), Year of construction: 2010, Functionality: fully functional, Contrary to the provision described above, the machine is provided EXW free loaded TECHNICAL DETAILS Table diameter: 4000 mm Faceplate diameter: 4000 mm Turning diameter: approx. 4300 mm Rotation diameter: 4300 mm Control for program: Siemens Sinumerik 840D Cb9ts08 Vertical adjustment of supports right Z1: 705 mm Vertical adjustment of supports left Z2: 990 (+200) mm Workpiece height: max. 2580 mm Workpiece weight: 18.0 t Speed: 50 - 100 rpm Height above floor to top edge of table: 1090 mm Distance between side uprights inside up to a height of 500 mm: 4,300 mm Distance between side uprights inside from a height of 500 mm: 2,580 mm Height lower edge of support/table: max. 2,250 mm Distance left support Z 2 to table: max. 2,560 mm Distance right support Z 1 to table: max. 2,550 mm Distance left to right support Z2 to Z1: max. 4,830 mm Carrier lift adjustable in height on side stand: approx. 2000 mm MACHINE DETAILS Total power requirement: 150 kW Machine weight: approx. 88.0 t Machine dimensions: 6,000 x 8,000 x 6,400 mm Footprint: 8.0 x 10.0 x 6.8 m EQUIPMENT 4x clamping elements approx. 1200 mm (additional clamping jaws optionally available) Various supports for alignment (height) lying on pallet Chip conveyor (6.9 x 1.25 x 1.1 m)

more

Auction

6

Ends in

 d  Hrs  Min  Sec Auction ended

4-axis horizontal machining center

FEELER FMH 500

€20,000

Condition: good (used), Year of construction: 2009, Functionality: fully functional, TECHNICAL DETAILS Gp8y7k9b9 Control system: Fanuc 18i-MB Working area: 762 x 710 x 710 mm Table size: 500 x 500 mm Speed: 8000 rpm Tools: 40-fold Pallet changer: 2-fold Cooling system: IKZ Feed: 30 m/min Rapid traverse: 20 m/min MACHINE DETAILS Weight: approx. 13,500 kg

more

Listing

Unanderra

2,228 km

High Speed Stamping Press

BRUDERER BSTA 30II (BSTA25)

US$25,000

ONO plus VAT

Sales inquiries Send inquiry Already requested Call

Condition: excellent (used), Year of construction: 1982, All offers will be considered! BRUDERER BSTA 30II (BSTA25) Precision high speed punching press. Nominal capacity: 250 [kN]; 25 [tons]. Min./Max. number of strokes: 100/1500. Year of manufacture: 1982. Max width of strip: 203 [mm]. Variable stroke: 13, 16, 19, 25, 32, 38 [mm]. Fitted with one roll feeders BBV 202/120. on the left Feed length variable up to 120 [mm] max. C33gg8qxa Optional: Sound insulating cabin. Condition: good working and visual order. Oil pump. Oil cooler. Execution: 4 supports. Front and rear safety guards. Fitted with spring feet dampers. Table dimensions: 530 x 530 [mm]. Passage between the supports: Longitudinal 540 [mm]; Lateral 203 [m Slide adjustment 51 [mm]. All technical documentation in English language included. Press weight. 5000 [kg]. Press height: 2520 [mm]. Fully refurbished under licence by Bruderer Singapore in 2002

Send inquiry Send inquiry Already requested more

Listing

Request more images Request more images Already requested

2

Gold Coast

2,427 km

DOOSAN LYNX 220LC

DOOSAN LYNX 220LC

US$26,090

EXW Fixed price plus VAT

Sales inquiries Send inquiry Already requested Call

Condition: excellent (used), Year of construction: 2007, Doosan LYNX 220 LC CNC Lathe PRICE REDUCTION -Reliable and high-performance CNC lathe, perfect for a variety of applications. This machine is in excellent condition and has been well-maintained. Features: Max turning diameter: 12.6" Max turning length: 20.7" Swing over bed: 20.1" 8l9ryi3dt3 Spindle speed: 4000 RPM 12-station automatic turret Fanuc CNC control Benefits: Accurate and precise machining Fast and efficient production Easy to operate and maintain Durable and reliable This lathe is on offer from the same company as the following high pressure water jetting equipment Price is in USD, and does not include taxes.

Send inquiry Send inquiry Already requested more

Listing

Request more images Request more images Already requested

5

Australien

4,162 km

Lathes

Mazak QUICK TURN NEXUS 450 II

Price info Price info Already requested Call

Condition: ready for operation (used), Year of construction: 2008, Control Unit Brand Mazatrol Model Matrix Nexus Main Drive Spindle speed range 2000 Spindle motor power 50/40 HP Movement X-Axis Movement 308 mm B29vxb0u Y-Axis Movement 1070 mm Z-Axis Movement 1025 mm This MAZAK QUICK TURN NEXUS 450 II lathe was manufactured in the year 2008 in Japan. It is equipped with a Mazatrol Matrix Nexus control unit. The machine has a spindle speed of 2000 rpm. Application Types Turning

Price info Price info Already requested more

Listing

Request more images Request more images Already requested

5

Taiwan

9,094 km

Cylindrical Grinding Machine

Kraft/Praise TT60-30L-C2-H

Price info Price info Already requested Call

Condition: new, grinding diameter:600 mm grinding length:3000 mm centre height:320 mm max. workpiece weight:3000 (zwischen Spitzen) kg max. workpiece weight:6000 (m. Lünetten) kg grinding wheel diameter:760 mm grinding wheel width:304,8 mm grinding wheel speed:45 (stufenlos) m/sec table travel:3400 mm table speed -stepless-:10~6000 mm/min Rotation speed of workhead :8~80 1/min tailstock quill stroke:100 mm taper in tailstock-quill:6 MK spindle drive:22,5 kW Weight approx.:13 t dimensions:13000x2900x1800 mm CNC controller:Siemens 840D mit Schleifzyklen Scales:in X-Achse von Heidenhain B9yx8hvrxv open steady:optional live center:optional Stk./pc workpiece drive:variable 4 jaw chuck:optional CE-design:verlängert die Auslieferung um ca. 3 Wochen warranty: None payment: 100% before loading

Price info Price info Already requested more

Listing

Request more images Request more images Already requested

1

Gold Coast

2,427 km

CNC MILLING MACHINE

DOOSAN DNM 650

US$48,900

EXW ONO plus VAT

Sales inquiries Send inquiry Already requested Call

Condition: excellent (used), Year of construction: 2008, Doosan DNM 650 CNC Milling Machine 8l9lbwnrru PRICE REDUCTION - Reliable and high-performance CNC milling machine, perfect for a variety of applications. This machine is in excellent condition and has been well-maintained. Get in touch today to learn more!

Send inquiry Send inquiry Already requested more

Listing

Request more images Request more images Already requested

8

Thailand

9,874 km

Laser cutting machines

Mitsubishi ML3015eX F60

Price info Price info Already requested Call

Condition: ready for operation (used), Year of construction: 2017, Control Unit Brand Mitsubishi Main Drive Bgloocj327b Laser power 6,0 kW This Mitsubishi ML3015eX F60 Laser cutting machine was manufactured in the year 2017 in Japan. It is equipped with a Mitsubishi control unit. The machine has a laser power of 6,0 kW. Application Types Laser Cutting

Price info Price info Already requested more

Listing

Taiwan

9,094 km

Double Column Milling M/C - Gantry Type

KRAFT HDT-18|HDT-21|HDT-24

Price info Price info Already requested Call

Condition: new, :HDT-18|HDT-21|HDT-24 x-travel:2000/4000/6000/8000/10000/12000/14000/16000/18000/20000 mm y-travel:1800|2100|2400 mm z-travel:800/1000 mm distance between columns:1850|2150|2450 mm w-axis:N/A table width:1200|1500|1800 mm table length:= X-Weg distance spindle nose and table:555~1355 mm spindle cone:SK 50/BT 50 turning speeds:6000 U/min (mehr auf Anfrage) spindle drive:18,5/22 kW (mehr auf Anfrage) 9uecccke feed speeds:X/Y/Z: 15/15/12 m/min machine length:6,5~23,5 m machine width:5,9|6,2|6,5 m Weight approx.:20t+2t/m|22t+2t/m|24t+2,5t/m automatic tool changer:32-fach CNC controller:Siemens/Heidenhain/Fanuc Telescope cover for guideways:für die X-Achse Scales:in X- und Y-Achse (W-Achse) cloth cover:für die Y-Achse (JAVARA) CNC controls from:Siemens/Fanuc/Heidenhain different kind of milling heads:90°/5-Achs simultan/5-Seiten/Universal etc. CTS:40-70 bar heavy duty ram:550x550mm/650x650mm ATC:60/90/120

Price info Price info Already requested more

Listing

Request more images Request more images Already requested

6

South Korea

9,811 km

Lathes

Hyundai Wia E 200A

Price info Price info Already requested Call

Condition: ready for operation (used), Year of construction: 2017, General Data Machine weight 3800 kg Control Unit Brand Fanuc Knzrdbiq Model i-SERIES Main Drive Spindle speed range 6000 This Hyundai Wia E 200A Lathe was manufactured in the year 2017 in South Korea. It is equipped with a Fanuc i-SERIES control unit. The machine has a spindle speed of 6000 rpm. Application Types Turning

Price info Price info Already requested more

Listing

Request more images Request more images Already requested

5

Taiwan

9,094 km

Facing Lathe

KRAFT FB-15 | FB-20 | FB-25 | FB-30

Price info Price info Already requested Call

Condition: new, :FB-15 | FB-20 | FB-25 | FB-30 turning diameter:1500|2000|2500|2500 mm faceplate diameter:1500|2000|2500|2500 mm turning length:330 mm max. workpiece length:450 mm bed width:450 mm max. workpiece weight -without tailstock:3000 kg width of cross cariage:250 mm spindle bore:155 (230 opt.) mm spindle nose:A2-11 (A2-15 opt.) spindle cone:7 MK spindle speed:4-600|4-600|4-400|4-400 1/min spindle speed steps:4 cross way of carriage:330 mm 3gevssq2g movement longitudinal:1000|1000|1500|1500 mm spindle drive:22 (29 opt.) kW servo motor X-axis:ß12/3000i 1.8kw |ß12/3000i 1.8kw|1FL6067 2.0kw|1FL6067 2.0kw servo motor Z-axis:ß22/3000i 3kw |ß22/3000i 3kw |1FL6092 3.5kw|1FL6092 3.5kw ball screw:Ø25mm x P5 x C3 (X-Achse) ball screw:Ø40mm x P10 x C5 (Z-Achse) mm rapid power traverse in X-and Z direction:6/8 m/min number of tools:4 tool post size:32x32 mm weight of the machine ca.:7000|7500|8000|10000 kg Machine size (LxWxH):2200x2200x2500|2200x2600x2750|25003000x3000x3100|3000x32 00x3350 mm tool holder:4-fach CNC controls from:Siemens/Fanuc/Fagor

Price info Price info Already requested more

Save search query