Plate shears - mecha. over 3mm plate thickness for sale
Your location was not identified (Edit)
|
4
4000x3,0 mm. 4.0 mm aluminium, 2.0 mm stainless steel, in good condition, with plate holding device to the rear, with motor stop, with lateral angular stop and front supports, depth stop 1000mm, with manual cutting gap adjustmentNote: Machine is currently under revision, the illustrations were made before the revision. Machine is repaired, tested, cleaned by a specialist and is then fully functional.test run is carried out.colour: grey/bluetotal power requirement: 400 Vmachine weight approx.: 60... more
|
|
8
All-purpose, electromotive impact/table shears of the Schuler brand for trade and industry. Robust and extremely stable cast iron construction. Large cast iron worktable and backgauge system with scale (open design: suitable for endless cuts). Triggering of the impact/table shears by operation of the skirting board. The guillotine shears were still in use until recently and are in an operational and clean condition. Maximum sheet thickness: iron: 1.5mm steel: 1mmDimensions impact shear:Cutting/w... more
|
|
2
Jelenia Góra, Poland
17500 km
1984
good (used)
Guillotine shears STROJARNE PIESOK CNTA 3150/25 A built in 1984 in Czechoslovakia by the well-known brand STROJARNE PIESOK. Be78szsjtr Technical data : - maximum length of cut sheet: 3150 mm - maximum thickness of cut sheet: 25 mm - dimensions of the machine (length x width x height): 4250 x 2140 x 3120 mm - weight: 25,000 kg more
|
|
8
Gütersloh, Germany
17923 km
excellent (used)
Max. Cutting length: 1040 mm Bflp0rl3ni Max. sheet thickness: 4 mm steel Manual backgauge with handwheels up to 1000 mm Side stop and table extensions Knife sharpened more
|
|
2
Menden, Germany
dealership location
17988 km
1972
good (used)
Cutting knife length: 2600 mm. Staender passage: approx. 2100 mm. Lkjol Cutting capacity: max. 4 mm. Extension: approx. 200 mm. Rear stop ( Mechanical with handwheel ) Foot loess and front support strips Weight: approx. 3000 kg. Dimensions, LxWxH: 2800 x 1400 x 1400 mm. The machine can be inspected and demonstrated in consultation under electricity and is immediately available. Please also note my other advertisements. more
|
|
4
Sheet width 2000 mm Sheet thickness 4 mm Total power requirement kW Gvxeis Machine weight approx. t Space requirements approx. m more
|
|
6
plate width: 2000 mm plate thickness: 6,3 mm distance between columns: 2280 mm cutting angle - upper blade: 1°30` ° back gauge - adjustable: [...] manuell mm number of cutting strokes max.: 60 Hübe/min height over floor: 900 mm voltage: 380/50 V / Hz S8wquomak total power requirement: 11,8 kW Weight approx.: 4,3 t space requirement of the machine approx.: 3,0x0,7x1,55 m Crank Guillotine Shear - continous + single stroke possible - driven by electric motor - down (force = 940kp) with guard - lim... more
|
|
8
All-purpose, electromotive impact/table shears of the Schuler brand for trade and industry. Robust and extremely stable cast iron construction. Large cast iron worktable and backgauge system with scale (open design: suitable for endless cuts). Triggering of the impact/table shears by operation of the skirting board. The guillotine shears were still in use until recently and are in an operational and clean condition. Maximum sheet thickness: iron: 1.5mm steel: 1mmDimensions impact shear:Cutting/w... more
|
|
4
Jelenia Góra, Poland
17500 km
1985
good (used)
The guillotine shears STROJARNE PIESOK NTA 3150/10A were built in 1985. Beyie0jklm Technical parameters : - cutting length: 3150 mm - maximum cutting thickness: 10 mm - minimum cutting thickness: 1 mm - weight: 14,000 kg more
|
|
7
Rotthalmünster, Germany
17739 km
1981
ready for operation (used)
Electro-mechanical sheet metal shears NTC 2500 - 4 Manufacturer: Piesok CSSR MANR. N 74 -005 built in 1981 Performance according to the operating book: Cutting capacity: 4 mm / 400 N / mm² Cutting length: 2550 mm Cutting angle: 1.33 ° Projection in stand: 200 mm Performance d. Electric motor: 5.5 KW Dimension: 3100 x 1600 x height; 1420 mm Weight: approx. 3,800 kg Bc7djvz0ab deal with accessories, operating book The electrical cabinet was modernized in 2003 with various ele... more
|
|
|
|
3
. Cut length 1000 mm Cut strength 1-6 mm without cutting cleavage! Exoffload 130 mm . Lift number 50/min Drive power 4 kW Weight estimated 3 to Yr7vn8 . Width about 2.3 m Depth without arms about 1.7 m Depth with arms about 2.4 m . Niederhalter with rubber pieces Backstroke manually 500 mm Side attack 1200 mm . ..... more
|
|
3
sheet width 2500 mm plate thickness 10 mm distance between columns 2550 mm throat 400 mm total power requirement 18 kW weight of the machine ca. 10,5 t dimensions of machine L x W x H 3,82 x 2,11 x 1,9 m Dwlj2q Accessories: back gauge, table extensions more
|
|
6
sheet width: 2000 mm 7nypprzbi plate thickness: 4 mm throat of pillar: mm distance between columns: 2230 mm cutting gap adjustment: ja / jes mm table-size: L: 2350 x B: 500 mm height over floor: 960 mm knife length: 2180 mm down holder: ja mm back gauge: 680 manuell mm strokes per minute: 56 Hübe/min weight of the machine ca.: 3,25 t dimension machine [...]: 2,22 x 2,75 x 1,54 m dimensions electric cabinet: 0,60 x 0,25 x 0,75 m further details: - control via foot switch - table has support arm... more
|
|
1
sheet width:3150 mm plate thickness:6,3 mm distance between columns:3150 mm motor back gauge area:0-600 mm Bexyduasns nose angle of upper knife:1,3° number of strokes :25-50 U/min Number of holddown units:13 total power requirement:11 kW dimensions of the machine ca.:3800 x 2160 x 1700 mm weight of the machine ca.:8500 kg more
|
|
2
Jelenia Góra, Poland
17500 km
good (used)
Guillotine shears ZAMECH NG 13. Technical data : - the largest thickness of cut sheet: 13 mm - the largest length of cut sheet: 3080 mm - length of knives: 3250 mm - spacing of side walls: 3200 mm - power demand: 21.5 kW Fwz3dan - number of knife strokes per minute: 12 - flywheel diameter: 1100 mm - number of revolutions of the flywheel per minute: 500 - overhang: 600 mm - stand extension: 600 mm - dimensions of the machine (width x length x height): 3300 x 4300 x 3050 mm - sciss... more
|
|
10
Motorized impact scissors Hezinger-CutLine model A04-3000 Cutting length 3,060 mm Sheet thickness 400 N/mm2 4.0 mm Sheet thickness 750 N/mm2 2.0 mm Drive power 7.5 kW Table height 800 mm Dimensions (L x W x H) 3,770 x 2,250 x 1,400 mm Bdhioitydb (for dimension B without CE-grid in case of rear stop 750 mm) Machine weight 4,000 kg with pneumatic tin holding either backwards or forwards. Front removal from the sheet metal tray.up to section length 750 mm more
|
|
4
Leopoldshöhe, Germany
17902 km
1969
ready for operation (used)
Mechanical sheet metal shears make Stückmann + Hillen, Brackwede/ Bielefeld, Old. Model,Y.J., power 1500 x 4.5 mm, with front Bff0dz8t9r Material pads and stop, MOTORIC LÄNGENVERD, Mech. Holder, motor 380 V/ 5.5 KW,solid design,accessory 1 spare Pair of knives, kl. Repair point, machine in use can be used, immediately from stock, freely charged on truck/ABHOLFAHRZEUG, short-haul delivery Possible! Sales on behalf of the customer ! Price € 999,--+MW tax net/if applicable VB by arrangement... more
|
|
6
Tatabánya, Hungary
dealership location
17372 km
1976
good (used)
Cut length: 3150 mm Cut thickness: 16 mm Dvifle Weight: 19500 kg more
|
|
4
Trittau, Germany
17716 km
1996
excellent (used)
Make: Schroeder Built: 1996 Sheet width: 2040 mm Sheet thickness: 4 mm Dimensions: approx. L 3.00 x W 1.60 x H 1.50 m Weight: approx. 3.5 t Facilities: Iqg7wez • Man. Back stroke • Pneum. Hold • Man. Cutting gap adjustment All information without guarantee. A demonstration of the machine is possible at any time in our exhibition. more
|
|
8
Table shears Fabr. FASTI type 507 20/3.25 Masch.# 95527023 year of manufacture 1995 Technical data: Cutting length 2040 mm maximum sheet thickness 3.25 mm Ss9ku8 Number of strokes per minute 50 Shear angle 1° 20 x 125 mm projection Lower holder force 13000 N the smallest remaining section on the table 30 mm the smallest remaining section behind the table 10 mm adjustment range of the backgauge 10-750 mm Motor power 7,5 kW Electricity 380 V / 50 Hz Weight approx. 2,6 t External d... more
|
|
5
Jelenia Góra, Poland
17500 km
1987
good (used)
Guillotine shears H 3222 produced in 1987 by Kuźnia Zakłady Prasonożyceowe USRR. Shear plates for sheet metal with an inclined knife 16 x 3150 mm are designed for straight metal cutting in the form of sheets and flat bars with an immediate strength of not more than 500 MPa and with a thickness of up to 16 mm. Mdmmv8x2 more
|
|
7
Motor-driven shears Hezinger CutLine model A04-2000 Cutting length 2,060 mm Sheet strength 400 N / mm² 4.0 mm Sheet strength 750 N / mm² 2.0 mm 7.5 kW Table height 800 mm Dimensions (L x W x H) 2,800 x 2.250 x 1,400 mm (the measure B without CE grilles for back gauge 750 mm) Machine weight: 3.000 kg Bdhinvrm09 more
|
|
7
Stable small table scissors from a training with a high cutting performance Manufacturer Stückmann & Hillen Cutting length 1.020mm Be3rbflm8w Sheet thickness max 4.5mm more
|
|
5
Factory: DURMA Type: MS 3004 Built: 2019 – demonstration machine Cut length: 3100 mm Sheet strength: 4 mm Control: EZM9910 Engine hours: 0 Cut angle: 1 ° 30 Lift count per min: 42 Ikh7877 Engine power: 7.5 kW Back attack area: 750 mm Table width: 450 mm Table height: 800 mm Dimensions L/B/H: 3700x2300x1350 mm Weight: 3780 kg Standard Control unit EZM9910 Backstroke area 750 mm programmable via control unit Plastic inserts for keepers 1 side stroke and 2 sheet metal chargin... more
|
|
5
sheet width 3060 mm plate thickness 5,0 mm no. of strokes 35 Hub/min total power requirement 7,5 kW weight of the machine ca. 5,37 t range L-W-H 4,4 x 2,3 x 1,7 mm Ben8q3j0fl more
|
|
2
Motorized plate scissors Fabr. SCHECHTL Type SMT 100 Masch. 3950 built in 1990 Technical data: Cutting length 1040 mm max. cutting thickness 3.5 mm Shear angle 2° 15 Cuts per minute 35 Drive power 3 kW Dimensions 1360 x 850 x 1155 mm Weight 760 kg with - hand-adjustable rear stop 0-500 mm - extendable table extension - Foot switch Be3zqlzmte used, in very good condition more
|
|
4
Jelenia Góra, Poland
17500 km
1971
good (used)
Guillotine shears WFO NG 5/2500 built in Poland by WFO. Technical parameters : - sheet thickness: 5 mm - cutting length: 2500 mm - overhang: 200 mm - number of jumps: 50 1 / min. - main engine power: 7.5 kW - main engine speed: 1420 1 / min. - bumper motor power: 0.4 kW - the number of revolutions of the bumper motor: 1400 1 / min. G9g9g9 - machine weight: 4350 kg - Overall dimensions (length x width x height): 3200 x 2070 x 1370 mm - foot control - DTR - technical and operationa... more
|
|
9
Boxmeer, Netherlands
18087 km
1959
ready for operation (used)
KB-1701 Fischer 3000/6 Mechanical panel scissors, used machine, 3000 x 6mm (max 6.8mm) Item number: KB-1701 Brand: Fisherman Model: 3000/6 Built: 1959 Series nr: 634051 Capacity (Kw): 8 Be03z2jopo Voltage: 380 Frequency (Hz): 50 Dimensions LxBxH (mm): 3750 x 1800 x 1750 Stucco number in stock: 1 Weight (kg) approx: 6500 Made in: Germany Capacity length (mm): 3000 Capacity strength (mm): 6.0 (max 6.8mm) Hintenanschlag: Manual Comments: As/is condition, untested, extra set of spa... more
|
|
1
Oberschweinbach, Germany
17891 km
ready for operation (used)
Batting scissors Bevo92bi3h 6mm x 2m more
|
|
4
Technical data: Built: 2000/2001 Nmgax Max. Tin thickness: 6.3mm Cut length: 3100 mm Weight: 6.5 to Accessories: Light barrier, pn. High-maintenance more
|
|
5
sheet width 1040 mm plate thickness 4,0 mm total power requirement 7,5 kW W3tr0 weight of the machine ca. 2.200 kg more
|
|
1
Böheimkirchen, Austria
dealership location
17558 km
used
sheet length: 2540sheet thickness: 4total power requirements: 7,5 kwweight approx.: ca 4,5 to Nhhnd more
|
|
2
3100 x 3, 5 mm with tin coating, cutting gap adjustment, Engine rear gauge front adjustable, cut stroke counter Color: grey Dimensions: 3800 x 2000 x 1600 mm with Schnittspaltverstellun Bdzcytydux Supply voltage: 16 A adjustable with holders without cutting angle adjustment without Backgauge Machine repaired by a qualified technician, tested, clean and is fully functional. Test run is performed. more
|
|
13
Gießen, Germany
17976 km
1982
good (used)
used, good condition from clearance 1 x AMADA M-2045 mechanical table shears with motor-driven Backgauge Dwebhy Year of construction: 1982 equipped with AMADA length indicator and mororischem Backgauge Working width: 2000 mm Cutting capacity: 4.5 mm Stroke: approx. 60 RPM Space Lxwxh: 3200 x 2000 x 1800 mm Weight: approx. 4600 kg Price is plus VAT free loaded bearing casting - shipping agreement and costs possible. Changes / errors in the specifications and subject to prio... more
|
|
3
Lambsborn, Germany
dealership location
18110 km
excellent (used)
Fisherman Kragarm Regal Wall assembly + stand assembly 6 stands 2000 x 3000 long 8j3nmhw 2500 mm high Exoffload 600 mm more
|
|
4
sheet width 2000 mm sheet thickness 6,3 mm gap 215 mm adjustability of backgauge 0 - 600 mm size of machine 2800 x 2160 mm Tuo8qum7f height of machine 1600 mm weight 7350 kg connected load 11,25 kVA voltage 380 V motoric backgauge pneumatic clutch hydraulic hold downs electrical cabinet more
|
|
1
Voest Alpine BT8x2500 - plate shear 22qmiohn Sheet thickness: 8 mm cutting length: 2500 mm throat depth: 400 mm stroke rate: 21 / min main motor: 7,5 kW dimensions WxHxD: approx. 3100 x 2300 x 2500 mm weight: approx. 8000 kg more
|
|
1
2030 x 2, 5 mm, 3.5 mm aluminium, with cutting line illumination, with front pull pad with Backgauge and sheet metal high locking mechanism forward ablegend, good and stable design Machine repaired by a qualified technician, tested, clean and is fully functional. Test run is performed. Note: Z2fbuxwp Machine is located currently in the revision, the pictures originated before the revision. The engine was disassembled for repair work. more
|
|
7
Sonneberg, Germany
17820 km
1959
good (used)
Machine number: 060-017/59 Cutting length: 2,540 mm Cutting thickness: 3,15 mm Table: 2,700 x 330 mm Trailing stop: 500 mm G0rrbvnk Pads front: 550 mm (4 pieces) Condition: good, newly polished, tested knife, ready to use Accessories: extra set of blades Connection: 4,5 kW Weight: 4,5 t Mass: 3,300 x 1,600 x 1.600 mm more
|
|
5
Motor-driven table shears Fabr. IRLE type TSU Masch.# 671250 built in 1968 Ii0lhhyt Technical data: Max sheet width 1250 mm maximum sheet thickness 6.0 mm Projection 280 mm Working height 800 mm Weight approx. 1,3 t External dimensions approx. 2100 x 2000 x 1600 mm needed, despite year of manufacture in good condition more
|
|
2
Dortmund-Wambel, Germany
dealership location
17999 km
1961
good (used)
1 used well preserved motor plate shear maximum cutting length 3050 mm maximum sheet thickness 6 mm Mpzpt Dimensions L x W x H 3900 x 2380 x 1800 mm weight approx. 6000 kg Accessories / special features: • Manually adjustable rear Backgauge • Protection grille at the rear of the back gauge with electrical circuit protection • 1 angle stop • 3 PCs. Auflegearme • Electric foot switch Siegfried Volz machine tools Rueschebrinkstr. 151-153 D-44143 Dortmund - Wambel more
|
|
2
Length: 2040 mm Maximum sheet thickness: 4 mm Bebwiofzve Cutting gap adjustment, manual back gauge more
|
|
3
working width: 2500 mm metal sheet thickness: 4 mm throat: 70 mm rear stop: 520 mm power: 380 V, 6,3 kW space needed: 3200 x 2300 x 1270 mm Rhlnr0ibq weight: 4600 kg more
|
|
4
8g8umebsi Shears Make: Darley 3.050 x 16 Type: GS3100x16 Capacity: 3.050 x 16 mm Year of make: 1996 With electr. backstop With security Stock Number: sch291 more
|
|
1
Motor. mechanical table shears Fabr. HUTTENLOCHER & Saeed type HSK / S Masch.# 3108 530/10, built in 1985 Technical data: Length 530 mm Cutting performance d. 40 kg / strength 10 mm 7.5 kW Weight 1.8 t Outer dimensions 1600 x 2150 mm Uoqfnj2r with -Counter -hand male rear gauge 0-600 mm T-slots on the table -Angle stop left 1000 mm -hand-operated lubrication -Cut gap setting on fine-thread spindle -1 set spare blades -Support arms more
|
|
6
C707qptce Shears Make: Mengele GWF 4050x20 Type: S20-4000 Capacity: 4.050 x 20 mm Year of make: 1988 Workpressure: 260 bar Weight Machine: 37.500 kg With unloading conveyor Stock Number: sch247 more
|
|
6
Shears Make: Irle Type: KS 10 S Capacity: Max. 10 mm Diam. of round: 3.000 mm Mzb9x Diam. of cutterblades: 220 mm Cutting speed standard: 12 m/min Power of main drive: 7,5 kW Round cutting shear Look also at Shipbuilding press van de Graaf (pers307) Stock Number: sch253 more
|
|
2
sheet width:1560 mm Bjd2dqc9 plate thickness:4 mm cutting angle:2° 25' strokes per minute:41 U/min back stop - range:750 mm table width:455 mm table height:800 mm total power requirement:7,5 kW weight of the machine ca.:2500 kg dimensions of the machine ca.:2100 x 2250 x 1400 mm more
|
|
|
Didn't find what you were looking for? Please contact our partners for this category :
Dealer for Sheet metal working
Dealer for Sheet metal working
