Condition: used, Year of construction: 2021, Exhibition unit (little used) Lubrication: Grease Max. output speed n2: 4,000 rpm Gear ratio (n1:n2): 1:0.8 Weight: approx. 8 kg Machine connection: HSK F63 Tool holder Usable width: 24 Storage location: Garbsen Djln T Aovvi Iwj Ufokl

Condition: used, Year of construction: 2022, in a sturdy galvanized sheet steel construction. Work surface with special folding cardboard filter, an additional post-filter and a filter cassette for extraction in the floor area. All filters can be changed quickly and easily. The internal radial fan, in explosion-proof design, is equipped with a blade wheel made of galvanized sheet steel. The explosion-proof drive motor (EEx nA II) is located outside the air flow and drives the fan directly. A 10 m long supply cable and a plug-circuit breaker combination with a built-in on/off switch are included in the scope of delivery. CAUTION! The switch is not explosion-proof and is only approved for use outside of potentially explosive areas. The fan pressure nozzle is located at the top. The air outlet is vertically upwards. Our paint mist extraction wall complies with the latest regulations of the Immission Control Act. The paint mist extraction wall is designed for installation in Zone 2 painting areas, where the average calculated concentration of flammable solvents is limited to < 25% of the lower explosion limit. Technical data: Max. volume flow: 3500 m3/h Exhaust air nozzle: 300 mm diameter. Work surface: 2000 x 1000 mm Space requirement: 2600 x 920 x 1420 mm high Motor: 1.50 kW, EEx nA II T3, IP 55 1500 min-1, B5, 400 V, 50 Hz ATEX marking Ex II 3 G Sound pressure level: 75 dB(A) Weight: 220 kg Fan: right Folding cardboard filter: 1000 x 2000 mm - 1 piece 2072090518 Filter cut-out for Paint-Star - 1 piece 2072091473 Cassette filter for Paintstar - 1 piece Floor tray PBA 20/24 1 piece Length A: 1984 mm, width B: 2378 mm Access ramp for PBA 20/24 1 piece Energy saving flap pn 300mm Each unit includes an air cylinder, 10 m air hose, and a lever valve with a bracket for hanging a spray gun. The energy-saving flap allows approximately 80% of heat energy and approximately 30% of electrical energy to be saved during setup time. Storage location: Garbsen Dkoljvvizdjn T A Ufsl

Condition: used, Total height 6500 mm Floor space 2000 x 2000 mm Outdoor installation Compact filter series Model PKFP – 1 element – 1.92 x 1.92 Shaking filter Overpressure operation Filter hose length 2500 m long – 180 mm diameter - then 105 m2 filter area 2 raw air fans – 2 pipes (diameter 300 mm) 1 x fan KT 300, 15 kW power 6361 m³/h built in 1999 1 x fan S 25 / 300, 7.5 kW power 7400 m³/h, built in 1993 1 x transport fan 6.1 kW, power 57 m³/min, built in 1996 Total approx. 14,000 m3/h volume flow Briquette press Höcker Polytechnik type BrikStar C 3 - 12. 1225 Motor 3.0 kW, briquette diameter 65 mm, output approx. 40-45 kg/h depending on the specific weight of the material. Deln Tovviyte A Ufjkl Storage location: Nattheim

Condition: used, Year of construction: 2001, Cutting width: 3300 mm Cutting length: 3350 mm Weight: approx. 4000 kg Saw blade projection: 100-(115) mm Saw carriage: Feed speed: 100-(130) m/min. Return speed: 100-(130) m/min. Main saw blade: 400-(430) mm Motor: 7.5-(11-13.2) kW Scoring unit: 215 mm Motor: 2.2 kW Pusher: Rapid feed: 160 m/min. Return speed: 60 m/min. Extraction: Air speed: 30-35 m/sec. Extraction nozzle: 200 mm / 115 mm Compressed air: Pressure: 5-6 bar Consumption: 20-30 l/min. Storage location: Nattheim Dkslevvkqgon T A Ufol

Condition: used, Year of construction: 1992, Max. cutting width: 5300 mm Max. cutting height: 2200 mm Saw blade diameter: 300 mm Max. processing thickness: 80 mm Saw blade bore: 30 mm Bottom support: Fixed rollers Saw head pivoting: Manual Saw feed: Automatic Extraction: External extraction Approx. weight: 1500 kg Motor power: 5.5 kW Storage location: Nattheim Djln T A Uovvkq Tsfekl

Condition: used, Year of construction: 2001, Baffle width: 4000 mm. Baffle height: 1000 mm. External dimensions: 4600 x 1500 mm. 2 x 1.5 kW motors. Total nominal flow rate: 7000 m³/h. Right and left exhaust nozzles with 300 mm diameter. Dsljvvizken T A Ufekl Storage location: Garbsen

Condition: used, Year of construction: 2002, Machining dimensions (tool diameter 25mm): X=3015 mm Y=1483 mm Z=325 mm Max. travels: X=3268 mm Y=1483 mm Z=325 mm Max. programming speed: X/Y = 75 m/min / Z = 30m/min Tool holder HSK 63F Drilling unit 7964, 14 vertical drilling spindles with 32 mm grid (10 in x / 4 in y) Sawing unit 7946 3.6 kW, 90° pneumatically pivotable Milling unit 7933 9 kW Wood Her Vector axis (C-axis) Tool magazine (6 disk places) Hand control unit Laser device (positioning of the suction cups) PC control panel with 17" monitor Operating system Windows 2000 Software: TwinCAM32 - office version Vacuum pump 100 m³/h Dry running Selective safety mats (3-field division) Storage location: Nattheim Deljvvi Nbsn T A Ufskl

Condition: used, Year of construction: 2022, Plus freight 4,000.00 € and installation and commissioning 5,000.00 € Grinding system B Sand 5 with partial lathe Working principle The panel is placed on the infeed table. It goes into the partial lathe and centered. It is ground in the grinding system, through and back. The panel is turned in the partial lathe. It is ground on the other side in the grinding system. Then there are two options: either the panel goes onto the outfeed table and unloaded or it comes back onto the infeed table and is unloaded there (the second option extends the working time). Grinding system equipment 1 upper grinding lamella roller suitable for surfaces. Power 3 kW; D 420 mm; L 1300 mm. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. 3 upper sanding discs for perfectly trimming the longitudinal and transverse wood fibers. Power 1.5 kW each; D 400 mm. Disc brush for beveling edges. The unit functions as a deep brush. After detecting the panel edges, it will follow the door edges. Power 0.75 kW; D 250 mm. Machine features: -The unique sanding system of this machine guarantees perfect wood sanding and/or intermediate sanding of the panels. -All tools are controlled by frequency converters. -All brushes are equipped with quick-release sanding strips without replacing the hub. -The discs are equipped with air bladders to optimize cleaning and service life. -Sanding discs are equipped with a Velcro fastening system. -The feed and rotation speed are PLC-controlled to prevent edge breakage. -High-quality sanding on 4 sides thanks to the system's constant removal rate. -Automatic and rapid unit changeover. - Constant throughput height, PLC and industrial software enable interlinking in a surface line. - Continuously variable speed of the discs, brushes and feed thanks to the fully equipped frequency converter. - Right/left rotation of the discs and brushes with different abrasive grits. - Individually driven feed of the discs, rollers and belts. - Additional adjustment of the brushes and discs to balance the use of the abrasive and to allow for changing the grinding pressure on the surfaces. - Strong support bed made of tubular steel guarantees the best rigidity, stability and flatness. - Planed upper support bed to ensure the best parallelism of the working surface for the grinding discs. - All unit carriages are designed with linear recirculating ball bearing guides, thus high load capacity and high precision. - Motorized feed belt controlled by a frequency converter, 0.55 kW. Machine doors equipped with safety devices. - Machine doors equipped with windows to observe the workpieces during operation. - Under the units, there are 80 mm rubber-coated pressure rollers to hold the workpieces in place during processing. · Low follow-up costs thanks to individual blade replacement. · Low running noise thanks to the enclosed system housing. · All units have suction housings with their respective suction supports. Cover plate with suction nozzle. · Completely encapsulated machine housing for a clean environment. Doln T A Ujvvkipsfekl

Condition: used, Year of construction: 1997, Number of belts: 1 belt, max. clearance height: 150 mm, max. working width: 1100 mm. 1st unit: Combination unit. 1st roller diameter: Steel roller. 1st unit design: Roller/shoe unit. 1st sanding shoe design: Electronic individual links. Segment width: 50 mm. 1st sanding belt length: 1900 mm. 1st sanding belt width: 1120 mm. Motor: 1 kW. Feed speed: 4 and 8 m/min. 2nd unit: Dust brush. Approx. weight: 2000 kg. Dimensions: 1800 x 1450 x 2120 mm. Storage location: Nattheim Dslovvkkasn T A Ufekl

Condition: used, Year of construction: 2014, Speed: 1450 rpm Motor: 2.4 kW Suction capacity / Flow rate: 70 m³/h Suction pressure: 3 mbar Tank: Operating pressure: 0.99 bar Capacity / Liters: 90 Operating temperature: 50°C Year of manufacture: 1989 No. 400 100 Djlnjvvi Nns T A Ufekl Storage location: Supplier

Condition: used, Year of construction: 2003, Working height: 2300 mm, Working width: 3500 mm, Motor: 1.5 kW, 3 pressure cylinders from above, 2 from the side, Pressure per cylinder: 3000 kg, Cylinder stroke: up to 200 mm, Hydraulics: 10-150 bar, Space required: 3950 x 900 x 2550 mm, Weight: 670 kg Dkeln T A Uovvkmbsfjl Storage location: Nattheim

Condition: used, Year of construction: 1998, Saw blade diameter: 180 mm. Saw blade bore: 30 mm. Maximum cutting length: 3100 mm. Weight approx.: 450 kg. Dimensions: 3600 x 900 x 1600 mm. Motor power: 2.2 kW. Wood dust tested: HO971001. Delevvkauon T A Ufokl Storage location: Nattheim

Condition: used, Year of construction: 1985, Cutting length: 3100 mm Cutting height: Adjustable from 0-45 mm Saw unit: Powerful three-phase motor 220/380 volts, 1.8 kW power Clamping bar at the top with a handwheel Storage location: Nattheim Dkeln T A Usvvkazofol

Condition: used, Year of construction: 1981, Roller diameter: 800 mm, maximum blade length: 5600 mm, minimum blade length: 5450 mm, maximum cutting height: 500 mm, maximum cutting width: 780 mm, table tiltable: Yes, column side: left, automatic motor brake: Yes, saw blade guide position: top and bottom, saw blade guide: roller guide, design: stationary, working height or feed table height: 950 mm, weight approx.: 720 kg, dimensions: 1480 x 900 x 2440 mm, motor power: 4.0 kW, extraction diameter: 125 mm Djlovvkmnon T A Ufekl Storage location: Nattheim

Condition: used, Year of construction: 1973, With a left-hand circular saw that can be swiveled to 45°. Cutting size: 2200 x 2500 mm. 3 motors, each with 4.5 kW. Both cross-cut saws can be swiveled to 45° - 90°, each with a scoring motor. All three saws can be driven up to 400 mm in diameter. Minimum cutting width: 210 mm. Both scoring saws are pneumatically displaced forward and backward. With vacuum suction cups for panel securing. Dkslsvvkm Ijn T A Ufol Storage location: Nattheim

Condition: used, Year of construction: 1973, Storage location: Nattheim Dksln T Asvvkt Uo Ufsl

Year of construction: 2018, Condition: used, Effective flow rate: 660 L/min. Motor: 4.0 kW. Max. pressure: 10 bar. Tank capacity: 270 L. *Compressor only. Storage location: Nattheim Delevvkhrsn T A Ufskl

Condition: used, Year of construction: 1996, Vacuum system with rotary valve. Nominal flow rate: 12,500 m³/h. Filter area: 62.5 m². Weight: 1,350 kg. Maximum vacuum: 4,000 Pa. Maximum air pressure: 8.5 bar. Dkjln T Asvviyge Ufsl Storage location: Customer.

Condition: used, Year of construction: 1997, 4-axis machine with 18 kW water-cooled main spindle. HSK F63 chuck X = 4750 mm Y = 1250 mm Z = 200 mm. Maximum speed: 18,000 rpm. 12-station X-axis grooving saw. 4-station drilling head in a 17-spindle spindle. Central lubrication. 17 vertical drilling spindles, completely renewed in 2019. Smooth table. Positioning aid. Stop rows. Pendulum machining. 2 vacuum pumps. All plug-in cards for the control system replaced in 2022. WoodWOP 4.0 tools. Optional: lock case cutter unit, door hinge drilling unit, saw blade unit, 4-spindle unit. Very well-maintained condition. Dksln T Ajvvi D Ej Ufjl Storage location: Customer

Condition: used, Year of construction: 2001, Max. edge band thickness: 0.2 - 12 mm Min. workpiece thickness: 8 mm Max. workpiece thickness: 42 mm Min. workpiece width: 70 mm Feed speed 1: 12 m/min Heat-up time: approx. 8 min Joining unit: Yes, with 2 milling units Automatic roll magazine: Yes Trimming shears up to: 3.0 mm Solid edge magazine: Yes Gluing: Glue pot with granulate on top Trimming saw: Yes, double trimming unit Flush trimming unit: pneumatically adjustable Chamfer and radius milling unit: pneumatically adjustable with interchangeable motors Rounding unit: pneumatically adjustable (corner rounding) Profile scraper: pneumatically adjustable Flat scraper: Yes, scanning Buffing unit: oscillating Unit display: Digital Control type: Section control/PLC Operation: Screen/PC control Extendable Roller support: Yes. Protective cover: Yes. Working height or feed table height: 800 mm. Approx. weight: 2100 kg. Dimensions: 5300 x 950 x 1300 mm. Motor power: 12 kW. Dsln T A Uovvkdaefskl Storage location: Customer.

Condition: used, Year of construction: 1988, Working width: 1100 mm, 2-belt machine Deln T Asvvkkgo Ufskl Storage location: Nattheim

Year of construction: 2021, Condition: used, Air flow rate: 900 l/min. Air flow rate: 54 m³/h. Maximum pressure: 16 bar. Air connection: 1/2. Power consumption: 0.18 kW. Dimensions: Length: 325 mm. Width / Depth: 430 mm. Height: 445 mm. Weight: 24 kg. Storage location: Garbsen Dkeln Tjvvkhxo A Ufsl

Condition: used, Storage location: Nattheim Doln T A Uevvkrdjfskl

Condition: used, Max. blade length: 5600 mm Roller diameter: 800 mm Max. cutting height: 520 mm Max. cutting width: 770 mm Table tiltable: Yes Stand side: Left Stop ruler: Yes Saw blade guide: Roller guide Design: Stationary Weight approx.: 800 kg Storage location: Nattheim Dkeln T Aevvkmue Ufel

Condition: used, Year of construction: 1994, Design: swiveling Swivel angle forwards: + 45° Swivel angle backwards: -10 degrees Table length: 2500 mm Table width: 870 mm Extendable frame support: Yes Number of speeds: 5 Speeds: 3000/4500/6000/7000/10000 rpm Speed selection: Belt shifting + pole switching Speed display: LED Cone of the milling spindle: with 25 pneumatic interchangeable spindles Clamping length of milling spindle: 120 mm Diameter of milling arbor: 30 mm Material of stand: steel Control panel position: above Height adjustment of spindle: electric Swivel adjustment of spindle: electric Spindle locking: manual Spindle brakes: yes Extraction diameter of milling stop: 120 mm Extraction diameter of machine: 120 mm Spindle direction: left/right Motor power: 5.5 kW Electric axes: Spindle height & swivel Table opening closing: Insert segment Stop jaw design: Aigner stop system Stop adjustment: Motorized Milling jaw adjustment: Manual Feed mechanism: Yes Feed adjustment: Fixed speeds Feed: 4 rollers Weight approx.: 1000 kg Dimensions: 2500 x 1500 x 1400 mm Dsln T A Uovvkufofjkl Storage location: Nattheim