Year of construction: 2025, condition: new, Vacuum membrane press VPR-3500 is a universal Press for the wood processing and thermoforming. The VPR-3500 press is also adjustable and mobile. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components Vakkumsystem: work surface with vacuum channels for a uniform Unterdruckauch for large workpieces. Hpsdpjd Ecc Tjfx Ad Toa Becker Vakkumpumpe / oil free / tank capacity 100 l Work surface: 3500x1500mm Pump output: KW 0.75 Vacuum pump flow rate: 40 m3/h Rubber membrane Dimensions exterior: 3600 x 1650 x 1000 mm Weight: 400 kg Location: Off the shelf 54634 Bitburg -free load-

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Hsdpfx Aswp Rqfod Tepa Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: used, Year of construction: 2003, Working height: 2300 mm, Working width: 3500 mm, Motor: 1.5 kW, 3 pressure cylinders from above, 2 from the side, Pressure per cylinder: 3000 kg, Cylinder stroke: up to 200 mm, Hydraulics: 10-150 bar, Space required: 3950 x 900 x 2550 mm, Weight: 670 kg Hpjdpfovvkmbjx Ad Tea Storage location: Nattheim

Condition: like new (used), Year of construction: 2019, functionality: fully functional, feed length X-axis: 3,000 mm, feed length Y-axis: 1,500 mm, Lightly used ORMA MEMBRANE PRESS, model DUPLEX 30/15 vacuum press with preheating oven/table for acrylic and thermoform plastics. Has only seen occasional light project use. Suitable, for example, for processing Corian sheets. An alternative to buying a new machine. Pressing area: 3000 x 1500 mm Vacuum pressing force across the entire work area: 44 tons 11 tons/m2 Maximum pressing height: 500 mm ORMA HEATING OVEN/TABLE 30/15 FOR ACRYLICS AND THERMOFORM PLASTICS • Heating by electric resistors and air circulation • Heated area: 3000 x 1500 mm • Max height of workpiece: 100 mm • Heating power: 18 kW • Maximum temperature: 200°C • Digital temperature control from the control panel The unit's frame is made from welded thick steel beam structure and welded steel sheets. There is an insulation layer between the galvanized steel sheets of the oven’s inner and outer surfaces. Manual oven opening, guided rails, and transport wheels. Membrane press bed is phenolic-coated plywood featuring a grid pattern for improved vacuum distribution. The top section, where the membrane film is mounted, opens 45 degrees and is equipped with gas springs. Hjdpfx Asxz Rhfjd Tjpa Quick and easy upper section locking. Manual membrane film quick-mount system. Vacuum system with a single 25 m3/h vacuum pump. Control panel, installed on the left side of the machine, includes: • Main switch • Control voltage indicator lamp • Emergency Stop button • Temperature monitoring/control • Vacuum pump status light on/off • Heater status light on/off

Condition: used, functionality: fully functional, TECHNICAL SPECIFICATIONS: - Working height: 970 mm (+100 mm) - Press width: 1300 mm - Pneumatic pressure: 1 unit Hpjdsxxuwljpfx Ad Tsa - Cylinder stroke: 200 mm - Applied pressure: 0.3 MPa

Condition: excellent (used), total width: 1,300 mm, total length: 3,500 mm, overall weight: 7,000 kg, operating pressure: 300 bar, transport width: 1,600 mm, transport height: 2,350 mm, transport length: 4,350 mm, Simimpiantin Shelf Press for Veneering 3500×1300 Shelf length: 3500 mm Shelf width: 1300 mm Two loads Press with 8 cylinders Shelves heated with water from central heating Max. working pressure: 300 bar Piston diameter: 80 mm Machine weight: 7000 kg Hodpsxxpgbofx Ad Tspa Machine dimensions: 435×160×235 cm (H)

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 1 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Hedetnz Ttjpfx Ad Topa Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Condition: used, For sale: Salmatec Maxima 700 pellet press in full working condition, installed in a Rematec container with electrical cabinet and a tent shelter. Capacity – up to 3 t/h. The line includes: - Press and hammer mill: Salmatec – reliable German quality with high efficiency and durability. - Conveying and dosing equipment: Rematec – robust and precise material handling at every stage. - Additional equipment: cyclones, sieves, cooler, control cabinet, etc. - Tent shelter. Key advantages: - High production capacity – up to 3 t/h. - High-quality European manufacturer components. - Suitable for professional pellet production from wood biomass, agro-biomass or other raw materials. - Fully operational line – demonstration possible. - Available immediately. Dismantling and transport are to be arranged by the buyer. We can recommend a company to assist with this process. The equipment can be inspected in full working order in Sweden. All foundation drawings and DWG files are available. Price: EUR 600,000 Hpodoit I Rtopfx Ad Tsa

Condition: used, Year of construction: 1992, Dimensions: 5700 x 1300 x 2400 mm Hpedevvkl Depfx Ad Tsa Storage location: Nattheim

Condition: excellent (used), Catalogue number 7811 TECHNICAL DATA - Compression force: hydraulic - Briquette shape: round - Briquette diameter: 60 mm - Hopper diameter: 990 mm - Throughput: approx. 70 kg/h - Automatic machine operation - Inspection window - Motor: 5.59 kW - Max. operating pressure: 150 bar - Dimensions (L/W/H): 1700x1350x1550 mm - Weight: approx. 1100 kg ADVANTAGES – Italian manufacture Hsdpfx Ajxxlb Ujd Tjpa – Used briquetting press – Inspection window – Very good condition Net price: 35,900 PLN Net price: 8,550 EUR based on an exchange rate of 4.2 EUR (Prices may change due to exchange rate fluctuations)

Condition: good (used), Code: 0163 Brand: ITALPRESSE Model: MEC 4/B Hydraulic hot press with water heating for veneer, panels, furniture, custom-made furniture, doors in wood, composite materials, aluminium and various Technical data: Platen dimensions mm 2500 x 1300 Opening mm 300 Hjdpfjwzbfwex Ad Tepa N° 4 cylinders Total pressure ton 60 Motor power Hp 1,5 Platen heating by water Boiler Perimeter emergency rope Overall dimensions mm 3100 x 1610 x 1830 h Weight kg 3000

Condition: used, Year of construction: 2023, functionality: fully functional, CLT Cross-Laminated Timber (CLT) production line with CNC machining center Capacity: approx. 25,000 m³/year (2-shift operation) Functional Description / Scope of Supply: - Longitudinal lamella feeding: Loading – Singulation - Cross lamella feeding: Loading – Vacuum destacking – Feeding to planer - Formation and buffering of longitudinal layers: Longitudinal layer preparation and discharge station - Formation and buffering of cross layers: Two-stage cross layer buffer – Cross layer discharge station - Layup and gluing area: Vacuum layup gantry – Adhesive application gantry – Layup table - CLT press: TimberPress X331 - Outfeed area after CLT press: Cross transfer carriage to buffer stations, Reichenbacher system and discharge station with flipping unit - Reichenbacher CNC machining center CLT blanks (LxWxH): Hedoxzy N Sspfx Ad Topa Min.: 6,000 x 2,000 x 60 mm Max.: 12,040 x 3,140 x 350 mm 3–9 layers Raw material: Longitudinal layers (LxWxH): Min.: 6,000 x 100 x 20 mm Max.: 12,040 x 280 x 50 mm Cross layers (LxWxH): Min.: 2,000 x 105 x 23 mm Max.: 3,140 x 285 x 53 mm Price and further information available on request.

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Lamella - carcass press with rapid traverse Technical data: Lamella carcass press from our showroom; Working range: width from 150 - 2.500mm , height from 150 - 1.400mm; depth 700mm; Hjdpfjiidm Nsx Ad Tspa - lamella press beam top with 6 elements, lamella press beam side with 5 elements - lamella press beam with practice-proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are 40 mm thick, coated continuous support plates - The pressing force of the pressing bars is infinitely variable electronically controlled by 2 potentiometers and adjusted via frequency converter, therefore the torque transmission is absolutely wear-free. - Pressing force for horizontal press bars min. 500 daN (kg) to infinitely variable max. 2200 daN (kg) - Pressing force for vertical press bars min. 300 daN (kg) to stepless max. 2200 daN (kg) - Including option: Rapid traverse speed for fast positioning of the press bars, controlled by automatic workpiece recognition with sensors in the press bars, press speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Jog mode for precise positioning of the two pressing beams e.g. for low pressing forces, drawers and carcasses 45 degrees. Simple operation via 6 separate pushbuttons, freely adjustable pressing time preselection with automatic opening, loading height 300 mm. Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Condition: ready for operation (used), Year of construction: 1996, Used Comafer 50/40 briquetting press. The briquetting press has undergone a complete overhaul. Hpedpjxzu Rdefx Ad Tja

Condition: ready for operation (used), Offered is an ODMI molded part press, year approx. 1980. 4 hydraulic cylinders, 1-4 cylinders, hydraulic pressure max/min 250bar/30bar, pressing force up to 50t per cylinder, 2 pressing stations, automatic operation, opening height 1120mm, cylinder stroke approx. 800mm, piston diameter 160mm, piston area per cylinder 201cm². Table size X/Y 745mm/2140mm, known defects: pull cord not correctly wired according to press inspection, emergency stop not up to current standard. Right cylinder with slightly leaking piston seal. Dimensions X/Y approx. 3200mm/1300mm, weight approx. 8000kg. Inspection possible by arrangement. Hjdpfx Asxzt Dvod Topa

Condition: used, Technical data: Number of pistons: 4 Piston diameter: 45 mm Connection to central heating: NO Shelf dimensions: 2500x1200 mm Clearance: 460 mm Hydraulic pressing Hsdoxzrt Ajpfx Ad Tjpa Motor power: 2 kW Power supply: 380 V Overall dimensions: Length: 2900 mm Width: 1370 mm Height: 2150 mm

Year of construction: 2025, condition: as good as new (ex-display), Vacuum membrane press VPR-3500 is a universal Press for the wood processing and thermoforming. The VPR-3500 press is also adjustable and mobile. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components Hpsdpfxjdvldae Ad Tja Vakkumsystem: work surface with vacuum channels for a uniform Unterdruckauch for large workpieces. Becker Vakkumpumpe / oil free / tank capacity 100 l Work surface: 3500x1500mm Pump output: KW 0.75 Vacuum pump flow rate: 40 m3/h Rubber membrane Dimensions exterior: 3600 x 1650 x 1000 mm Weight: 400 kg Location: Off the shelf 54634 Bitburg -free load-

Condition: used, Technical specifications: Briquette diameter: 60 mm Briquette length: 50 mm Hopper diameter: 1100 mm Hopper height: 910 mm Hopper capacity: 0.89 m³ Throughput: 60-80 kg/h Power supply: 400 V Motor power: 7.5 kW Safety switch Hpedjxzqmzspfx Ad Toa Overall dimensions: Length: 1670 mm Width: 1100 mm Height: 1500 mm

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - series are the ideal solution for the wood processing industry. VP 3000 is equipped with heating technology, which reduces the drying time of the adhesive so that the performance is higher. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components Hsdjdvltyspfx Ad Tspa The heating system is equipped with temperature control Rubber membrane 2.5 mm Table top is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of vacuum / Tankinhalr 15 l Work surface: 3000x1500mm Heating system temperature: Max 60 degrees C Heating system: KW 4,5 Pump output: KW 0.75 Vacuum pump capacity: 25 m3/h Rubber membrane Dimensions exterior: 3100 x 1650 x 1600 mm Weight: 450 kg Location: Off the shelf 54634 Bitburg -free load-

Condition: new, Year of construction: 2024, your benefits Sturdy press mechanism with low-wear, chrome-plated tongs Pressing chamber wear bush Pre-compressor with end-position-sensed cylinder and screwed cover Control box with SPS-control Screw channel with discharge screw Separate oil tank with pump motor and valve control Safety switch for oil temperature Mounting on stable base frame with rubber feet Briquette quantity monitoring Robust construction, low-maintenance technology, little space requirement: The machines of the C-series are particularly suitable for small and medium-size enterprises, whose required throughput does not exceed 50-80 kg/h or 200 to 400 kg/day. Practically any suitable material can be briquetted, e.g. wood, polystyrene, foam, paper or biomass. All machines are available as left- or right-hand version. The mounting on a stable base frame ensures a quick installation and makes mobile use possible. Briquette diameter (mm) 50 Hodpfx Ajcnz U Esd Tjpa Throughput capacity up to (kg/h) 50 (depending on material) Hydraulic motor (kW) 5,5o Screw motor (kW) 0,55 Oil quantity (litres) 100 Weight (kg approx.) 800 Outstanding features at a glance Hydraulics with separate oil tank: temperature-controlled hydraulic unit, complete valve control, pump motor for long running times Briquette length monitoring: regulates the length of the briquette to a constant level Pressing area wear bush: Prevents wear in the pressing area Location: Ex works - free loading

Condition: new, Year of construction: 2024, Weima Briquetting Press TH 714 The TH 714 machines are designed for plants with required throughput rates of up to 150 kg/h. The stable press housing enables the production of high-strength briquettes - from materials such as wood, polystyrene, foams, light metals, paper or biomass. Numerous additional options can be implemented, e.g. oil cooling for multi-shift operation. All machines are available as left- or right-hand version. Mounting on a stable base frame ensures fast installation and makes mobile use possible. User-friendly operation thanks to Siemens PLC control In order to live up to our performance promise, we design and produce all control cabinets ourselves at our Ilsfeld site and equip them with well-known international components. This guarantees highest quality with compact design. The used PLC-control from Siemens is perfectly adapted to the requirements of the briquetting process. Impurity-resistant screw conveyor due to cardanic suspension The screw conveyor, which transports the material into the pre-compressor of the briquetting press, is suspended on a cardan joint. This prevents interfering materials from causing damage to the screw conveyor. As is so often the case, however, it always depends on the specific application which suspension is chosen. For metal applications, for example, we often recommend rigidly mounted screws. Briquette diameter (mm): 70 Throughput capacity up to (kg/h): 150*1 Hydraulic motor (kW): 11 Oil quantity (liters): 250 Weight (approx. kg): 1100 Location: Ex stock 54634 Bitburg - immediately available - Hpedpfx Asil Hggsd Tja subject to prior sale

Condition: excellent (used), Year of construction: 2020, New hydraulic heating platen press Manufacturer: ITALPRESSE, Type XL/6 30-13 with gold-anodized plates Touch display control system - Electric heating platens 3,000 x 1,300 mm - Total pressing force: 90 tons - Number of heating plates: 2 pcs. - Number of levels: 1 - Cylinder stroke: 350 mm - Daylight opening: 350 mm - All-around loading possible - Number of hydraulic cylinders: 6 pcs. - Cylinder diameter: 85 mm - Hydraulic unit power requirement: 3 kW - Electric heating plates made of solid hard aluminum with built-in heating wires - Heating capacity: 22 kW - High-pressure insulation plates - Working temperature: 90° C - Max. temperature: 120° C - Operating voltage: 400 V, 50 Hz - Safety specifications according to CE standard Standard equipment: - Movement of the press table with rack-and-pinion and parallel guides at 2 corners of the press table made from self-lubricating material - Electronic control unit with touch screen for machine control and monitoring - Digital timer for adjusting pressing time and automatic opening - Digital input and monitoring of pressing pressure - Digital timer for adjusting pressing time - Digital diagnostics and fault display - Safety circuit with two-hand operation - Safety pull cord - Safety support for lower press table Accessories included: - Touch Screen TS/400 - EFC electronic flatness control - Gold-anodized heating plates (Busse) Hodpjxgbxfsfx Ad Topa Location: Ex stock - Immediately available -

Condition: new, Year of construction: 2024, Compact design, high reliability and an excellent price-performance price-performance ratio: these are the advantages of this machine machine, which is perfectly suitable for briquetting materials such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a sturdy base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044x1044 mm hopper height: 1010 mm hopper capacity: 1,1 m³ driving power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil capacity (l) 100 Weight (kg) 530 Equipment: Press Powerful press mechanism with low-wear, chrome plated tongs Precompressor with end-position-suspended cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Tank with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette quantity monitoring Automatic On - Off Location: 54634 Bitburg Hpedpfjbtnf Ejx Ad Tsa

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - Series are the optimal solution for woodworking. VP 3000 is equipped with the heating technology, which shortens the drying time of the glue, so that the efficiency is higher. Possible applications: Veneer / form gluing / wrapping... Coating of different profiles (veneer,paper, plastic...) Hsdpfx Aodwh E Aed Tspa Wood bending: production of bent and layer-glued components The heating system is equipped with temperature control Rubber membrane 2,5 mm Table top is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of the vacuum / tank capacity 15 l working area: 3000x1500mm Heating system temperature: Max. 60 degrees C heating system: KW 4,5 Pump capacity: KW 0,75 Vacuum pump flow rate: 25 m3/h Rubber membrane Dimensions outside: 3100 x 1650 x 1600 mm Weight: 450 kg Machine is equipped with a chassis. Location: From warehouse 54634 Bitburg - free on truck -

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 2 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Hodpfx Adjtnz Hbs Tspa Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg