Condition: good (used), Eccentric press / Punch press Inv. no. 3513 Made by WMW Type PEE 80 Pressing force: 80 tons Fehxsvkgfpez Hhrogb * Stroke adjustment: 10 to 100 mm * ram adjustable mm * Stroke rate stroke/min * Installation height 355 mm * 520 mm throat depth!!! * Table surface 920 x 700 mm * Clamping plate * Central lubrication Accessories: * Foot control / control panel with Dimeco control cabinet * Dimeco roll feed / belt width max. 600 mm * Sheet metal shears Machine weight approx. 7000 kg.

Condition: used, Year of construction: 1996, machine/vehicle number: 14.194, Pressure total: 80 - 800 ton Ram stroke: 1600 mm Free frontal opening L-R: 2850 mm Free lateral opening F-B: 1000 mm Daylight: 1900 mm Table surface area : 2800 x 2000 mm Slide area: 2800 x 2000 mm Die cushion capacity in table: 32 - 320 ton Die cushion stroke: 400 mm Die cushion pad area: 2500 x 1700 mm Approach speed: 400 mm / sec Working speed: 5 -42,7 mm / sec Return speed: 420 mm / sec Required power: 246 kW Height over floor approx.: 7785 mm Fgjhxz Hheu Saaasrjb Weight of machine approx.: 100 ton No. of moving bolster: 1 pcs.

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Fgohxzou Rwa Ij Hhreb Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: good (used), Year of construction: 1977, Pressure 160 t Ram adjustment 75 mm Fgjhxevi Ikqjz Hhrjb Strokes/min. 30-90 Stroke adjustment 20-130 mm Power requirement 15 KW Electrical system 380 V

Condition: excellent (used), Year of construction: 2015, With a view to optimized and energy-saving drives in the vehicle industry, significantly higher demands are placed on the components of the drive system. Higher power transmission and higher torques combined with smaller size are the challenges. This development has increased the demand for cold-formed splines. With the Vertical Splines Press (VSP) Sack & Kiesselbach provides the customer with a solution that offers technological and also logistical advantages compared to conventional technologies (such as roller burnishing or broaching). The relatively small and very user-friendly press can be configured both manually and as an automated system. In addition to the splines press, the customer can also obtain the appropriate die system and process technology from a single source. 1 used Vertical Splines Press make Sack & Kiesselbach type VSP 50/30 Year 2015 Technical data: Pressing force 500KN ram stroke 450 mm Closing speed 200 mm/s pressing speed 5,5 mm/s opening speed 120 mm/s table dimension 500 x 400 mm Fehxz Hsgtty Tshrsgb installation height 1000mm width between columns 530 mm splines cylinder speed 3-9,5 mm/s Dimensions height 2900 mm width 3100 mm depth 1400 mm Drive power 8 KW Special equipment Digital measuring system Splines tool for internal splines

Condition: used, clamping plate, clamping table, clamping cube, press table -Clamping table: clamping plate for hydraulic press eccentric press -Clamping surface: 365 x 305 mm Fohxz Hhou N Sinorjgb -Dimensions: see photo technical drawing -Dimensions: 365/305/H150 mm -Weight: 57 kg

Condition: ready for operation (used), Eccentric Press, Eccentric Press Machine, Eccentric Press, Digép SD-63, Used Machine Manufacturer: Digép Fshxz Hjr D Nb Iohrsgb Type: SD-63 Dimensions: 1400 x 1800 x 2450 mm Table Size: 740 x 555 mm Stroke: 10-110 mm Strokes per Minute: 60 Pressing Force: 63 tons

Condition: good (used), I sell Fein MSfv 649 Angle grinder with long neck. In bdb condition Fehxeuhm I Hez Hhrogb

Condition: used, Hydr. differential stroke press, toggle lever hydraulic press, automatic punching press BRUDERER - LEINHAAS type AR 11-100.H Fine blanking press, knuckle-joint press Machine. No. P247 Year of construction 1991 Pressing force 100 ton (1000 kN) Installation height max. 380 mm Table surface 1100 x 700 mm Outlet hole 800 x 220 mm ram surface 690 x 315 mm Frame width 1150 mm Lateral upright width 410 mm Stroke rate 45 and 80 strokes/min. Clamping pin bore Ø 50 mm Compressed air requirement 8-10 bar Hydraulic tank capacity approx. 700 liters Motor power main drive 22 kW Mains connection 400 Volt, 50 Hz, 28 kW - 2 speed settings for the number of strokes (45 and 80 strokes/min.) - electronic cam controller BALLUFF, type Minicontroller BMC4K - electronic tool monitoring EBERLE, type PLS 509S - KISTLER press force monitoring system - table surface with 22 mm T-slots and ram surface with 14 mm T-slots - Electronic stroke counter - motorized height adjustment for the ram - central oil lubrication - Work area shielding through pneumatic opening protective screen - adjacent control cabinet and electrical cabinet - 2 oil coolers with FLUTEC cooling fan (oil-air cooling) - Electrical circuit diagram and printout of PLC program available - Two-hand operation on the machine Space requirement (control cabinet) L x W x H 700 x 700 x 2100 mm ( approx. Space requirement (electrical cabinet) L x W x H 1700 x 650 x 2100 mm Space requirement (press) L x W x H 2350 x 1700 x 3300 mm Weight of the press 8500 kg Very good condition Fjhxz Hhegp T Eujrsgb

Condition: good (used), Year of construction: 1982, Table width 1.8 m Strokes per min. 30 - 150 Weight 47.000 KG Fgehxzjvi Iime Hhrob

Condition: used, clamping plate, clamping table, clamping cube, press table -Clamping table: clamping plate for hydraulic press eccentric press -Clamping surface: 500 x 280 mm Fgjhxz Hsu N Siushrob -Dimensions: see photo technical drawing -Dimensions: 500/280/H180 mm -Weight: 53 kg

Condition: good (used), Press machine, hydraulic press, used machine Manufacturer: SEJFO Model: 7051-3 Fohxz Hhjt A U Irjrogb Overall dimensions: 800 x 1400 x 2480 mm Weight: 996 kg Stroke length: 300 mm Maximum hydraulic pressure: 140 Bar Year of manufacture: 1997 Hydraulic power supply: 380 V; 50 Hz

Condition: excellent (used), pressing force: 5 t, I sell a Schling DUO 5T pneumatic press. Fshxz Hjudph Ujhrogb

Condition: used, Single column eccentric press WEINGARTEN type ERV 40 Machine No. 537 / 65 Year of construction 1965 Compressive force 40 ton. throat 230 mm table size 570 x 470 mm ram surface 250 x 200 mm clamping spigot bore Ø 40 mm installation height max. approx. 520 mm stroke adjustment 8 - 88 mm slide adjustment travel 63 mm Stroke rate 70 strokes per minute Drive power 3 kW Mains connection 380 Volt, 50 Hz - Table height adjustment - Overload protection by crushing plate - clutch-brake combination by WEINGARTEN friction thread clutch - electric 2-hand operation and foot switch - central lubrication via hand pump space requirement L x W x H 1600 x 1150 x 2300 mm Fgjhxz Hjffm Hhshrob weight approx. 2,6 ton.

Condition: good (used), Year of construction: 1972, pressing force: 160 t, Engine power 20 hp Fgshovi Iiaoxz Hhrsb

Condition: used, Single-column hydraulic press, straightening press, punching frame ECKOLD Press frame with hydraulic cylinder, mobile press, punching unit Type RSD 1500 - 125 Machine. No. 317 / 690 Year of construction approx. 1986 Compressive force 150 ton. throat 125 mm ram stroke 35 mm Table size 280 x 210 mm Plunger surface Ø 125 mm Installation height (ram to table) max. 265 mm Table height above floor 403 mm Hydraulic operating pressure max. 500 bar - without hydraulic unit - Plunger surface with 4 M16 threads and 20 mm guide groove, central centering hole Ø 15 mm Fshxjd Swtasz Hhrjgb - 1 high-pressure hydraulic hose with external thread M30x1.5 mm, hose length 4 meters - 1 high-pressure hydraulic hose with union nut M30x1.5 mm, hose length 4 meters Space requirement L x W x H 700 x 300 x 1450 mm Weight 1250 kg Good condition

Condition: good (used), Year of construction: 1977, Functionality: fully functional, Pressure: 16-40 t Fgehjvi Igxjxz Hhrob

Condition: used, Single-column hydraulic press HYDRAP type HPSK 25 No. 6312 Year of construction 1989 Pressure force 25 ton. Ram stroke 500 mm throat depth 300 mm Installation height 700 mm Table surface 1000 x 500 mm Table bore Ø 210 mm Plunger surface 400 x 360 mm Clamping pin bore Ø 40 mm Fehxohrakvsz Hhrogb Table height above floor 855 mm Feed speed in rapid traverse 280 mm/sec. Pressing speed 3.5 mm/sec. to 25 mm/sec. Return speed 280 mm/sec. Hydraulic tank capacity 240 liters Drive power 7.5 kW Mains connection 400 Volt, 50 Hz. - Operation and programming via SIEMENS S5 with OP1 control system - Measuring system for stroke adjustment - Pressing speed infinitely variable via potentiometer - Pressure setting infinitely adjustable manually via pressure regulator - Short stroke device - Mechanical tool clamping on ram with T-slots and clamping pin hole - Switch cabinet with electrical control on the machine - Two-hand operation and electrical connection for foot control - Control provided for electrical mold monitoring - Hydraulic diagram and electrical diagram available Space requirement L x W x H 1800 x 1200 x 2930 mm Weight approx. 4 tons good condition

Condition: used, Single column eccentric press MÜLLER GEFREES type 60 SV DK (identical in construction ExP60) Machine No. 5250686 Year of construction 1986 As good as new condition pressure force 60 ton. throat 280 mm table surface 740 x 560 mm ram area 385 x 200 mm drop-through hole in table 300 x 200 mm table surface intermediate table plate 740 x 560 mm drop-through hole in table intermediate plate Ø 103 mm thickness of intermediate table top 70 mm clamping spigot hole 40 mm Table height above floor 815 mm (with intermediate table top) Installation height max. 275 (with intermediate table top) Installation height max. 345 (without intermediate table top) Stroke adjustment 10-90 mm Plunger adjustment 60 mm Stroke rate 100 strokes/min. Motor power 3 kW drive power 380 Volt, 50 Hz - mechanical rotary wedge clutch with pneumatic control - spring-loaded single-jaw brake controlled via cam disk - stroke release via pneumatic foot switch - overload protection with crushing plate in ram - table height adjustment via 2 threaded spindles Fjhji A A Tboxz Hhrogb - manual grease central lubrication BEKA Schmiertechnik - Operating instructions and pneumatic diagram available space requirement L x W x H 1400 x 1100 x 2200 mm weight 3,4 ton. very good condition, as new

Condition: used, Single column eccentric press MÜLLER GEFREES type PDET 5 S/EK Machine No. Year of construction 1988 pressure force 5 ton. throat 125 mm head clearance 170 mm table area 280 x 220 mm waste hole Ø 90mm ram surface 160 x 100 mm stroke adjustment 4 to 40 mm ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Fjhxjik Srwez Hhrogb Clamping spigot bore Ø 25 mm Table height above floor 900 mm motor power 0,55 kW mains connection 380 volt, 50 Hz - pneumatic clutch-brake combination - electric foot switch - switch cabinet at the machine space requirement L x W x H 900 x 600 x 1700 mm weight 530 kg very good condition

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. Fjhxz Hhjdzp Tcorsgb From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: used, Single-column eccentric press EBU Type 75 SKU Fgjhsdzqltexz Hhrsb Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Double column eccentric punching press BLEMA Gotha type PEZ 160-50 MHSY-ES Eccentric press with roller feed ALBA Machine no. No. 88151005 Year of construction 1988 / 92 Pressure force 160 ton. Frame width 970 mm Stand width sideways 560 mm Table size 900 x 900 mm ram surface 900 x 700 mm Tool installation height 560 mm, max. 700 mm Stroke adjustment 8-160 mm Ram adjustment travel 125 mm Stroke rate 25 to 70 strokes/min. Belt width in roller feed max. 400 mm Motor power approx. 15 kW Mains connection 380 Volt, 50 Hz - Infinitely variable stroke rate via frequency control - Automatic stroke adjustment - ram weight compensation cylinder with compressed air - Hydraulic overload protection in the ram - Pneumatic clutch/brake combination - Central oil lubrication - Precisely guided press ram with oil-lubricated guides - UNIDOR press control - Swiveling control panel - Press and feed control cabinets, together on one platform, adjacent Platform dimensions 3400 x 2250 mm, height without feet 2950 mm Width of the press without feed 2100 mm Fjhedzqlvsxz Hhregb Depth of the press with drive motor 2300 mm Overall height of the press 4150 mm Weight of punching press approx. 18 tons. For transportation, the drive motor is removed and the machine is placed on its face. In addition: NC roll feed straightening machine ALBA type GGVHY400 Apparatus no. 1405 and 1406, order no. 910708 (year of manufacture 1992) - ALBA PSS 300 feed control - Feed length infinitely programmable from 0.1 to 6500 mm per stroke - Belt thickness at 400 mm width max. 3 mm - Belt thickness for 300 mm width max. 4 mm - Belt cross-section max. 1200 mm2 - Roller drive hydraulically controlled by the feed - Height-adjustable feed unit on the press to adjust the material infeed height - Hydraulic unit opposite - Drag straightener with hydraulic opening and closing Weight of the complete system approx. 24 tons Space required for transport a mega trailer with an internal height of 3 meters and a loading length of 13.6 meters good condition

Condition: used, Double column hydraulic press ALPHA TEC -- ALPHATEC type RPS 5000 fabric. no. 300487 year of construction 2006 pressure force 500 ton. stand width front and rear 2520 mm table area 2500 x 2500 mm ram surface 2500 x 2500 mm ram stroke 600 mm installation height max. 600 mm Table height above floor approx. 900 mm tank capacity approx. 1000 liters ram retraction force approx. 22 ton. Feed speed adjustable 100-800 mm/s Fgehodzqptexz Hhrob pressure build-up to 5000 kN approx. 0,7 sec. return stroke speed approx. 300 mm/s Motor power main motor 75 kW Motor power control pump 2,2 kW Mains connection 400 Volt, 50 Hz - 8-fold flat guide for the ram - Hydraulic ram locking at TDC - adjacent control cabinet (200 x 50 cm) - Electrical control SIEMENS SPS S7-314 - Operation via SIEMENS OP 170-B (5,7") - 2-hand control panel adjacent - ground level installation - table top 2510 x 2530 x 135 mm (approx. 6700kg) - central lubrication - operating instructions with circuit diagrams space requirement L x W x H 372 x 260 x 460 cm Space requirement for horizontal transport L x W x H 460 x 372 x 260 cm Weight approx. 50 ton. The machine was used for straightening of red-hot steel flanges. From insolvency - in good condition

Condition: used, Pneumatic press, compressed air press BOSCH Type No. 041 Year of manufacture 1980 Compressive force 18 KN = 1.8 tons at 5 bar 15 kN = 1.5 ton. at 4 bar 12 kN = 1.2 ton. at 3 bar 8 kN = 0.8 ton. at 2 bar 6 kN = 0.6 ton. at 1.8 bar Projection 100 mm Plunger stroke 70 mm Table surface 245 x 200 Plunger surface Ø 45 mm Installation height max. 235 mm Clamping pin bore Ø 20 mm with clamping screw Compressed air requirement 5 bar - Pressing force infinitely adjustable via pressure regulator - Pneumatic cylinder with ram height-adjustable by 90 mm - Pneumatic 2-hand operation - Mounted on metal base frame with wooden plates Fgehxz Hhjh U Dtujrjb Space requirement L x W x H 1050 x 700 x 1600 mm Weight of pneumatic press 82 kg Weight with table base 140 kg good condition