Eccentric presses single column 0-24t for sale
Your location was not identified (Edit)
Compressive force: 15.0 t
Xzg3o
Projection: 120 mm
Table: 460 x 255 mm
Installation height: 250 mm
Drive: 1,6 kW
Remark: infinitely variable speed adjustment
Weight: 750 kg more
.
- with height-adjustable table :
Output 10 to
Number of strokes 120 strokes
Throat 160 mm
ram stroke 8 - 80 mm
Tappet adjustment 40 mm
table adjustment approx. 120 mm
Installation height max. 290 mm
table 420 x 300 mm
Bmwo9gfudk
Width x depth approx. 0.7 x 0.8 m
Height approx. 1.7 m
Engine power 1 HP
Weight estimated approx. 0,7 to
.
..... more
pressure:10 T
throat:180 mm
stroke:8-60 mm
no. of strokes:180 Hub/min
table surface area:400 x 340 mm
Ltc0etyf
table height over floor:935 mm
hole in the table:80 mm
ram - range of adjustment:40 mm
ram surface:180 x 110 mm
total power requirement:1,1 kW
weight of the machine ca.:0,6 t
dimensions of the machine ca.:1,2 x 1,5 x 2,0 m more
new
pressure: 20throat depth: 200stroke: 0-50total power requirements: 2,2weight approx.: 1250messurements (LxWxH): 970 x 740 x 1.730
Bdf3jbmbw2 more
pressure 16 t
throat 250 mm
stroke 100 mm
table surface area 500x400 mm
Ben28bc8ev
ram surface 470x250 mm
hole in the table Ø 90 mm
table height 850 mm
tool hole in ram Ø 40 mm
weight of the machine ca. 2,5 t
dimensions of the machine ca. BxTxH 1200x1600x2200 mm more
Sold are 2 pcs. Eccentric presses. One eccentric press has an additional frame for lift truck transport. Pressing force 100kN, connected load 0,75 kW, 400 V.
Bmrcj08cp8
Further data can be seen in the photos. more
.capacity 16 tostrokes 125/min Mechanical foot release.outreach 200 mm ram adjustment 50 mmstroke adjustment 8-60 mm installation height with clamping plate approx. 220 mm.dimensions , width x depth x height approx. 0.7 x 1 x 2 mWeight approx. 1.1 to.....
Ihf0magc8 more
pressure:12 t
throat:220 mm
stroke:6-66 mm
no. of strokes:160 Hub/min
sheet thickness - max.:2 mm
ram adjustment:42 -12 mm
table::585 x 400 mm
clamping plate thickness:60 mm
ram surface:170 x 170 mm
Hole in clamping plate:Ø 80 mm
clamping plate:600 x 400 mm
Gxkcnzmti
flywheel machine equipped with DITTMER type PSK 103/B UVV-protection shield, manual central lubrication, foot switch, additional clamping plate 600 x 400 mm (thickness 60 mm), height-adjustable table (+/- 170 mm) more
new
pressure: 15throat depth: 200stroke: 0-40total power requirements: 1,5weight approx.: 840messurements (LxWxH): 970 x 740 x 1.730
Bdf3j79ss8 more
Single column eccentric press
Manufacturer BERRENBERG
Type EPG 12.5 / 300 N
Machine No. 14249 built in 1968 (12.5 tons press)
Pressure force 12.5 ton.
Projection 140 mm
Table size 495 x 285 mm
Ram surface 130 x 170 mm
Ofckj
Clamping pin bore ø 40 mm
Stroke adjustment 8-60 mm
Slide adjustment 30 mm
Installation height max. 185 mm
Stroke rate approx. 120 strokes / min
Table height above floor 850/750 mm
Table opening 170 x 105 mm
Mains connection 380 volts, 50 Hz
Motor power 1.5 kW
- mechanical fo... more
pressure 15 t
throat 200 mm
stroke 40 mm
table surface area 320 x 500 mm
Odfd2
no. of strokes 200 Hub/min
air pressure 4 - 6 bar
total power requirement 1,6 kW
weight of the machine ca. 0,8 t
dimensions of the machine ca. 1,0 x 0,8 x 1,8 m more
pressure 75 t
Qztrhiu7
stroke verstellbar mm
table size 650 x 650 mm
weight of the machine ca. 5 t more
pressure 20 t
throat 155 mm
stroke 6-60 mm
no. of strokes 84-210 Hub/min
ram - range of adjustment 50 mm
300 mm
table surface area 300x450 mm
table height 840 mm
hole in the table Ø 90 mm
ram surface 190x278 mm
tool hole in ram Ø 25 mm
total power requirement 1,5 kW
Npkvl
weight of the machine ca. 1,0 t
dimensions of the machine ca. BxTxH 1100x1100x1900 mm more
Eccentric press make DANGELMAIER type EP 2
Year of manufacture 1956
Technical data:
punching force 2,0 t
strokes per minute 200
stroke 25 mm
B7bv77y2
Bearing width 110 mm
Bearing depth 35 mm
Table size 215 x 135 mm
Throat 90 mm
Installation height 145 mm
Power 0,3 PS
Power supply 380 V / 50 Hz
with
- Swivel wedge coupling
- Foot disengagement
used, in good condition more
new
pressure: 10throat depth: 160stroke: 0-40messurements (LxWxH): 980 x 950 x 1670total power requirements: 0,75weight approx.: 600table diamension: 270 x 370
Dwefla more
Year 1961
Model: EPt
Od3b7
Size: 8/112N
Printing capacity: 8 to
Cut surface at Mat. 45kg festkt. 180mm
Adjustable stroke: 8 to 70mm
Adjustability of the ram: 30mm more
1990
ready for operation (used)
Manufacturer Czechoslovakia Smeral Trnava
The machine is disconnected, stored machine, without el. energy and compressed air supply hall - can not be tested
Machine weight 2.5 t
Ebf8ayr
Disassembly, removal and loading are not included. more
pressure 20 t
throat 155 mm
stroke 6-60 mm
no. of strokes 84-210 Hub/min
ram - range of adjustment 50 mm
300 mm
table surface area 300x450 mm
table height 840 mm
Iwfxffn
hole in the table Ø 90 mm
ram surface 190x278 mm
tool hole in ram Ø 25 mm
total power requirement 1,5 kW
weight of the machine ca. 1,0 t
dimensions of the machine ca. BxTxH 1100x1100x1900 mm more
eccentric press make AMBOLD type 10 t
Technical data:
Pressure force approx. 10 t
Plunger stroke approx. 60 mm
distance table ram surface approx. 280 mm
Clamping surface of the table 430 x 350 mm,
table height adjustable via 2 spindles
Engine power 1 kW
External dimensions L x D x H 900 x 1100 x 1600 mm
Weight approx. 730 kg
with
- mechanical two-hand engagement
- Foot indentation
used, in good condition
Bkbnlvbc more
Machine type: Eccentric press
Gqku7gwrs
Manufacturer: DANGELMAIER
Model: EP8
condition: good
Type of offer: used machine
Technical data:
Compressive force: 8.0 t
Projection: 115 mm
table: 315 x 230 mm
Installation height: 250 mm
Drive: 0,6 kW
Weight: 500 kg more
1979
good (used)
Stand eccentric press
Manufacturer: Paul Müller
Series No. 14430179 with test book
Type EXP 10
Built: 1979
Technical data:
Pressing force max. 110 KN
Discharge 160mm
Clamping area 520x325mm BxT
with cross grooves
Diarrhoea hole 125x125 mm
Pestle strokes 130 rpm
Pusher adjustable 40 mm
Stroke adjustable 8-80 mm
Table adjustable 160 mm
Engine power 0.75 kW
Operating voltage 380/220 V
Protection control with emergency emergency
faceted tools
pneumatically encapsulated
Test books available, last t... more
Power: 12 to
Size of bolster: 290 x 260 mm (w x d)
Size of additional plate: 600 x 300 mm (w x d), thickness 30 mm
Opening in bolster: 100 x 70 mm (w x d)
Size of ram: 120 x 100 mm (w x d)
Overhang: 150 mm
Blgjhq8hcd
Daylight: app. 250 mm above additional plate
Frequency: 50 - 250 1/min, manuel adjustable
Stroke: 6...60 mm
Ram adjustment: 80 mm
Motor power: 1,1kW
• pneumatic clutch
• manuel grease lubrication
• Stöber gering for stroke speed adjustment
• Herion valve
Working only ... more
pressure 75 t
Bnc3ohk7ra
stroke verstellbar mm
table size 700 x 580 mm
weight of the machine ca. 3,5 t more
1. SCOPE OF SERVICES
- EBU H 12 FT Eccentric press
- Siegfried SPC control unit
2. DOCUMENTATION
- Complete operating documentation available
3. TECHNICAL DATA
Year of construction: 2013
Type: Eccentric press
Bkqsamrbrk
Nominal force: 120 kN
Max. mould installation height: 170 mm
Max. weight of upper mould part: 25 kg
stroke adjustment range: 30 mm
ram height adjustment: 40 mm
Stroke rates: 40-200 1/min
Pneumatic operating pressure: 5.5/10 min/max bar
Electrical connection: 400 VAC, 50 Hz
Weight... more
Horizontal forging machine.
Fylqkubt
We are a metalworking company looking to sell its used machines. more
Eccentric press
Fabr. ter Hart
Type EP 6
Press force: 6 ton
Bktmrfv8bc
* Table: 280 x 190 mm
* Plunger stroke: 5 to 42 mm
* Tappet adjustment 35 mm
* Through hole: 90 mm
* Projection: 100 mm
* Installation height 170 mm
* Foot control
* Connection: 1.5 kW
* Weight :320 kg.
* PKZ with emergency stop
Very good condition !! more
Eccentric press make MABU type 12 TF
probably year of construction 1984
Technical data:
pressing force 12 t
Stroke adjustment 6 - 60 mm
Table size 380 x 270 mm
Through hole 100 mm
Bear size 120 x 100 mm
Installation height 210 mm
Throat 145 mm
Drive power 1,1 kW
Outer dimensions approx. 800 x 900 x 1750 mm
with
N7dut
- pneum. friction clutch
Control BA 1.1 for "with/without movable safety device
Movable protection not available!
- Height-adjustable table
- Foot switch
- Stroke counter
used, ... more
1969
ready for operation (used)
Eccentric press EBU SK 12 FU 1969 serial number P4989/69
Pressure 12 tons stroke adjustment 12 - 130 mm impact stroke creation
80 mm power approx. 11 hp
F9syu8p2o
Freely loaded into containers or trucks more
Plunger stroke 4 -40 mm
maximum distance table - ram 215 mm
Adjustability plunger down 32 mm
Number of strokes in throughput 160 mm
Bkedhkv82h
Mass ca.250 Kg more
presadora puente cnc de 3+2 ejes- control CNC FIDIA M2 (x-y-z+a+b) cabezal ortogonal UAG automatico indexado cada 2.5°.Superficie de la mesa 3000x1250- peso sobre la mesa: 10000kgs- Paso entre montantes: 1750mm- recoridos X-Y-Z: 2500x2000x1000mm - husillo: ISO-50 / 5000rpm /22kw- avance rapido : 15m/min-cabezal. Mandrino vertical- mando remoto- electro -mandrino externo "Faemat" de 30000 RPM - 2 mesas ranuradasde fundicion adicionales- hermantal dicerso.
Ukpsf32v more
All information without guarantee.
The machine is located in a very good condition. A demonstration is at any time possible in our showroom.
Cinijff9 more
Eccentric presses
Fabr. ter Hart
Type EP 13
Press force: 13 tons
* Table: 330 x 330 mm
* Plunger stroke: 5 to 50 mm
* Tappet adjustment 35 mm
Fv8asz9p
* Projection: 115 mm
* Installation height 200 mm
* Foot control
* Connection: 1 kW
* Weight : approx. 550 kg.
* New painting !!!
* PKZ with emergency stop
Eccentric press
Fabr. ter Hart
Type EP 25
Press force: 25 tons
* Table: 360 x 320 mm
* ram stroke: 6 to 60 mm
* Tappet adjustment 35 mm
* Through hole: 120 mm
* Projection: 175 mm
* Installatio... more
Eccentric press fabr. HELMERDING type PEP 12/15 B
machine # 831184, year of construction 1988
Technical data:
Nominal force 12 t
max. ram stroke 60 mm
Throat 160 mm
table clamping surface 315 x 400 mm
Adjustability of the ram 40 mm
max. stroke rate 180 rpm.
ram surface 100 x 125 mm
Drive power 1,1 kW
Bjwrvyfsmp
with
- 2-hand release
- Foot switch
- sep. switch cabinet
- Ortlinghaus additional brake and hydraulic multiple disc clutch
- according to UVV
used in good condition more
Eccentric press Make V & O Press Type FO 43 built 1980
Bkjhd8j3zf
Serial number 25ST-593 Pressing force approx. 25 tons more
pression: 12,5 t
throat: 150 mm
table size: 300 x 490 mm
clearance hole in the die:
Dglbi8x
table adjustment: 180 mm
tappet area: 130 x 170 mm
tappet adjustment: 40
stroke adjustment: 8 - 60 mm
number of strokes: 120 /min
engine: 380 V kW
space needed: 1070 x 1000 x 2020/2200 mm
weight: 955 kg more
Manufacturing origin Swiss
Voltage 380/50/3
Netweight with motor, without pillar 245-295 kg
Netweight of standard pillar 95 kg
Custom position 8462.9930
80eh39
TECHNICAL DATA TYPE D-8 / D8-200
Pressure exerted (maximum) 8 tons
Max. cross section area of blank (shearing strength
40 kg/mm2 200 mm2
Standard fixed stroke 20 mm
Variable stroke, standard range 4-36 mm
Variable stroke, extra wide range 8-50 mm
Distance from underside of slide to table, slide up 220 mm
Thickness of bolster plate ... more
Machine number: 7551
Type / Model: PEDV 10/II-S
Pressing force: 10 t
Table: 450 x 300 mm
Nm2v2
Pestle: 190 x 140 mm
Stroke stroke: 6 to 50 mm
Impact adjustment downwards: 45 mm
Table adjustment upwards: 140 mm
Diarrhoea hole: 140 mm
Extension: 170 mm
Distance table pestle max. 320 mm
Stroke capacity: 160 /min
Plate thickness single stroke: 2 mm
Sheet thickness Continuous stroke: 1 mm
Connection: 1.2 kW
Accessories/Equipment:
Condition: good
Weight: 1.0 t
Dimensions: 1,200 x 1,200 x 2,400 mm more
Eccentric press make ACOMA GEORG ACHTERMANN Stuttgart type TEP 10/160
comm. no. 61/80351
Technical data:
pressing pressure 10 t
Table size 380 x 300 mm
Installation height 250 mm
Throat 175 mm
Stroke of the ram 8 - 80 mm
Tappet play 40-120 /min
Power requirement 2,2 PS /900 rpm
External dimensions L x W x H 700 x 750 x 1750 mm
Weight approx. 800 kg
with
- Foot switch
T3kshtxf
used, in good condition more
Air clutch and two-hand indentation with foot switch.
Power / pressure 14 t
Strokes per min. approx. 100
56 mm max stroke adjustment
Table size 420 x 290 mm
maximum mounting height approx. 200 mm
Bdgqbx3jvg
Passage back 175 mm
Hole in the table 110/120 mm
0.73 kW
Weight approx. 1.5 t more
Built 1950 shield conversion of Schuler 1976.25 tonnes. Pressure of Schuler
maintained and checked last check July 2014. Closed in the July 215.
Dxugk2ln more
machine number: 99758
Type: AMP 22
Press force: 22 t
Table: 500 x 330 mm
ram: 400 x 150 mm
Through hole: mm
Hdqwfot
Throat: 175 mm
stroke adjustment: 6 to 60 mm
stroke rate: 120/min
Tappet adjustment:
condition: good
Equipment: Foot release
Connection: 1,47 kW (2PS)
Weight: approx. 1.2 t
Dimensions: 800 x 1,100 x 1,800 mm more
CCCP-Mockba eccentric press offered.
Press power: 16000 KG
Bbxgxbxd2j
Punch/min: 120
Ram stroke: 5-55 mm
Table: 420 x 280 mm
Dimensions: 100x110x210 cm (LxWxH)
For more information call us or send an e-mail. more
This may be of interest to you
Machineseeker becomes biggest sponsor of the 2nd Bundesliga in Germany
Photo gallery: the 10 strongest forklift trucks in the world
Machineseeker now also sponsering Greuther Fürth
New Machineseeker.com TV commercial with Michael van Gerwen
10 valuable tricks for buying used machines online
Photo gallery: The World's 10 biggest excavators
Didn't find what you were looking for? Please contact our partners for this category :
Dealer for Presses
Dealer for Presses
