Condition: excellent (used), functionality: fully functional, Description of the device Pump motor power - 1.35 kW 10 hydraulic cylinders for pressure - spring return 17 upper hydraulic cylinders for pressing the beam Maximum working dimensions 7x1.5m Hsdpjvy Uqfofx Ag Defr

Condition: good (used), Year of construction: 1983, functionality: fully functional, Bürkle U60 veneer press hydraulic Year of manufacture: 1983 Hsdpfx Aex Af Sbog Djfr The press comes from a training workshop and is in good condition. Press area: 2200 x 1250 mm Opening height: 400 mm 4 cylinders, pressing force: 600 kN Connected load per heating plate: 7 kW Weight: 3000 kg Dimensions: 2750x1380x1785 mm

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Hfodpfxewp Rqfo Ag Dsr Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: as good as new (ex-display), Year of construction: 2024, new heating plate press, hydraulic ITALPRESSE type XL/6 30-13 with gold anodized plates Touch display control - electric heating plates 3.000 x 1.300 mm - Total pressure 90 to. - Number of heating plates 2 pcs. - Number of shelves 1 pc. - Cylinder stroke 350 mm - Shelf opening 350 mm - Loading from all sides - Number of impression cylinders 6 pcs. - Diameter of pressure cylinders 85 mm Hfedpsdx R Tfjfx Ag Dor - Power requirement of hydraulic unit 3 kW - Electric heating plates made of solid hard aluminum with built-in heating wires - Heating capacity 22 KW - High-pressure insulating plates - Working temperature 90° C. - max. temperature 120° C. - Operating voltage 400 V/50 Hz - Safety regulations according to CE standard Standard equipment: - Movement of the press table with rack and parallel guides at 2 corners of the press table made of self-lubricating material - Touch screen electronic control unit for controlling and monitoring the machine - Digital timer for setting the pressing time and automatic opening - Digital input and monitoring of the pressing pressure - Digital timer for setting the pressing time - Digital diagnosis and display of fault messages - Safety circuit with two-hand operation - Safety rip cord - Safety bracket for lower pressing table Integrated accessories: - Touch Screen TS/400 - EFC electronic flatness control - Gold anodized heating plates (Busse) Location: From stock 54634 Bitburg - immediately available-

Condition: used, Year of construction: 2003, Working height: 2300 mm, Working width: 3500 mm, Motor: 1.5 kW, 3 pressure cylinders from above, 2 from the side, Pressure per cylinder: 3000 kg, Cylinder stroke: up to 200 mm, Hydraulics: 10-150 bar, Space required: 3950 x 900 x 2550 mm, Weight: 670 kg Storage location: Nattheim Hodpfx Asvvkmbsg Defr

Condition: used, For sale: Salmatec Maxima 700 pellet press in full working condition, installed in a Rematec container with electrical cabinet and a tent shelter. Capacity – up to 3 t/h. The line includes: - Press and hammer mill: Salmatec – reliable German quality with high efficiency and durability. - Conveying and dosing equipment: Rematec – robust and precise material handling at every stage. - Additional equipment: cyclones, sieves, cooler, control cabinet, etc. - Tent shelter. Key advantages: - High production capacity – up to 3 t/h. - High-quality European manufacturer components. - Suitable for professional pellet production from wood biomass, agro-biomass or other raw materials. - Fully operational line – demonstration possible. - Available immediately. Dismantling and transport are to be arranged by the buyer. We can recommend a company to assist with this process. The equipment can be inspected in full working order in Sweden. All foundation drawings and DWG files are available. Price: EUR 600,000 Hodpfx Asit I Rtsg Dsfr

Year of construction: 2008, condition: excellent (used), Electric heating element Shock- and impact-proof plug-in heating system with heating conductors embedded airtight in silicone.No wear, no corrosion, operational safety even in continuous operation and in case of impacts and shocks. Temperature adjustment via integrated controller with insulated control knob. Permanently connected industrial cable, no vulnerable plug connections. High-strength special aluminum profile for high load capacity and flat pressing surfaces on all sides. Gold anodized finish as standard, scratch and abrasion resistant, easy to clean. Size:Type: EST 21 Length: 2100 mm Connected load: 1100 Watt, 230 Volt Temperature: 0 / 40 / 70 / 100 / 170 / 200 degrees Hodpolcd Szofx Ag Dsfr Location: ex stock 54634 Bitburg - immediately available -

Condition: used, Year of construction: 1992, Dimensions: 5700 x 1300 x 2400 mm Hsdjvvkl Dspfx Ag Dsfr Storage location: Nattheim

Condition: excellent (used), Hess Corpus Press Type: Export, Pneumatic Manufacturer: Hess Type: Export Maximum workpiece size: 2,500 x 1,500 mm Press force: 1,400 kp pressing capacity per pressure unit at 15 bar Vertical cylinders: 2 + 2 pressure cylinders Horizontal cylinders: 2 + 2 pressure cylinders Dimensions: 3,900 mm x 2,500 mm x 600 mm Weight: 1,060 kg Hfsdpfexgvwpjx Ag Dor Hess Corpus Press Export, pneumatic 2 vertical pressure assemblies, each with 2 pressure cylinders, 80 mm cylinder diameter, 110 mm stroke, 1,400 kp pressing force per pressure unit at 15 bar 2 horizontal pressure assemblies, each with 2 pressure cylinders, 80 mm cylinder diameter, 110 mm stroke, 1,400 kp pressing force per pressure unit at 15 bar; the upper unit is easily adjustable thanks to weight compensation Pressing operation is controlled via 2 rotary slide valves with positions Press – Stop – Release Maintenance unit consisting of pressure regulator (0–15 bar), pressure gauge, and oil mist lubricator Anodized measuring scales, detachable feet Location: Ex works customer site - Immediately available -

Condition: excellent (used), Year of construction: 2016, LAMELLA – CASE CLAMP PRESS GANNOMAT “CONCEPT 70 ECO” Complete in standard configuration including: - Sturdy, torsion-resistant steel frame, constructed with welded and bolted assemblies - UPPER lamella pressure beam with 6 elements, SIDE lamella pressure beam with 5 elements - Lamella pressure beams feature the tried-and-tested tolerance compensation system (Ganner system) for tightly pressed carcass joints - Counter-pressure surfaces (side pressure wall, bottom) are 38 mm thick, coated, continuous support plates - Continuous pressing surface with a height of 95 mm on the lower vertical pressure beam - Electromotive adjustment of both pressure beams via precision trapezoidal thread spindles (with increased pitch and concentricity accuracy) and high-performance lead nuts with grease reservoir - Clamping is electromotor-driven, with two separate worm gear motors (2 x 0.75 kW) - The pressing force of the pressure beams is continuously adjustable electronically using two potentiometers and regulated via frequency inverters, providing a completely wear-free press force control - Pressing force for horizontal beam: min. 500 daN (kg) up to stepless max. 2200 daN (kg) Pressing force for vertical beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) Hsdjw Td A Iopfx Ag Dsfr - Press and adjustment speeds of the pressure beams with fine positioning, switchable via 3-stage selector: 5 / 10 / 25 mm/sec - Extremely user-friendly operation - Working height/loading height: 300 mm - Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm - Machine No. 563.624 - 400V, 3Ph, 50Hz (3.2 kVA, 16 A) Set of machine feet for 500 mm working height Operating manual in German Overhauled by Ganner, with 6-month parts warranty Location: ex stock 54634 Bitburg - Immediately available -

Condition: new, Year of construction: 2024, Super special price, as it was on display at our in-house exhibition. Hodpfjlht H Eex Ag Djfr Operating hours: 2 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg

Year of construction: 2025, condition: new, Vacuum membrane press VPR-3500 is a universal Press for the wood processing and thermoforming. The VPR-3500 press is also adjustable and mobile. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components Vakkumsystem: work surface with vacuum channels for a uniform Unterdruckauch for large workpieces. Becker Vakkumpumpe / oil free / tank capacity 100 l Work surface: 3500x1500mm Pump output: KW 0.75 Vacuum pump flow rate: 40 m3/h Rubber membrane Dimensions exterior: 3600 x 1650 x 1000 mm Hjdpod Ecc Tsfx Ag Defr Weight: 400 kg Location: Off the shelf 54634 Bitburg -free load-

Condition: as good as new (ex-display), Year of construction: 2024, Technical data: Slat carcass press from our showroom; Working range: width from 150 - 2.550mm, height from 150 - 1.400mm; depth from 150 - 700mm; Variable pressing force adjustment 300/700/1100/1400/1800/2200 dN(kg) of the lateral pressing beam; Hfedpob Eln Dsfx Ag Dor Variable pressing force adjustment 500/800/1200/1500/1900/2200 dN(kg) of the upper pressing bar Simple operation via 6 separate push buttons, Freely adjustable pressing time preselection with automatic opening, Charging height 300 mm Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg

Condition: excellent (used), Year of construction: 2013, LAMELLAR - CASE CLAMP GANNOMAT "CONCEPT 70 ECO" Complete in standard configuration with: Case joints. - Counter-pressure surfaces (side pressure wall, base) are 40 mm thick, coated, continuous support plates - Electrically operated adjustment of both press beams via precision trapezoidal-thread spindles (with increased lead and concentricity accuracy) and high-performance running nuts with grease reservoir. - Clamping is performed electrically using two separate worm gear motors (2 x 0.75 kW) - Pressing force: 2000 daN (kg) per press beam. - The pressing force of the press beam is electronically regulated and set via frequency converter, thus torque transmission is completely wear-free. - Pressing and adjustment speed: 25 mm/sec. - Very simple operation via 6 separate push buttons; 6 movement operations can be selected via the controller. - Freely adjustable pressing time preselection with automatic opening: 0-30 min (switchable to seconds or hours). - Working height/feeding height: 300 mm - Working dimensions: Length min: 150 mm, max: 2550 mm; Height min: 150 mm, max: 1400 mm. Depth: 700 mm 1 selector switch for variable pressing force: 1000 / 1500 / 2000 daN (kg) Machine No. 380.324 400V, 3Ph, 50Hz (2.5 kVA, 16 A) Set of machine feet for working height 500 mm Hfjdpfsw Tdymex Ag Dor Machine used: Year of construction: 2013, fully overhauled by Ganner, 6-month parts warranty Special price: ex-stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Hsdpfsw Sgnksx Ag Dsfr Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 1 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Hsdpfxstnz Ttj Ag Dsfr Location: 54634 Bitburg

Year of construction: 2025, condition: as good as new (ex-display), Vacuum membrane press VPR-3500 is a universal Press for the wood processing and thermoforming. The VPR-3500 press is also adjustable and mobile. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components Vakkumsystem: work surface with vacuum channels for a uniform Unterdruckauch for large workpieces. Becker Vakkumpumpe / oil free / tank capacity 100 l Hfsdpfxsdvldas Ag Dor Work surface: 3500x1500mm Pump output: KW 0.75 Vacuum pump flow rate: 40 m3/h Rubber membrane Dimensions exterior: 3600 x 1650 x 1000 mm Weight: 400 kg Location: Off the shelf 54634 Bitburg -free load-

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - series are the ideal solution for the wood processing industry. VP 3000 is equipped with heating technology, which reduces the drying time of the adhesive so that the performance is higher. Usage possibilities: Veneers / form gluing / wrapping... Coating of different profiles (veneer, paper, plastic...) Wood bending: Production of bent and glued components The heating system is equipped with temperature control Rubber membrane 2.5 mm Table top is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of vacuum / Tankinhalr 15 l Work surface: 3000x1500mm Heating system temperature: Max 60 degrees C Heating system: KW 4,5 Pump output: KW 0.75 Vacuum pump capacity: 25 m3/h Rubber membrane Dimensions exterior: 3100 x 1650 x 1600 mm Weight: 450 kg Location: Off the shelf 54634 Bitburg Hfjdpfx Aedvltyeg Der -free load-

Condition: new, Year of construction: 2024, your benefits Sturdy press mechanism with low-wear, chrome-plated tongs Pressing chamber wear bush Pre-compressor with end-position-sensed cylinder and screwed cover Control box with SPS-control Screw channel with discharge screw Separate oil tank with pump motor and valve control Safety switch for oil temperature Mounting on stable base frame with rubber feet Briquette quantity monitoring Robust construction, low-maintenance technology, little space requirement: The machines of the C-series are particularly suitable for small and medium-size enterprises, whose required throughput does not exceed 50-80 kg/h or 200 to 400 kg/day. Practically any suitable material can be briquetted, e.g. wood, polystyrene, foam, paper or biomass. All machines are available as left- or right-hand version. The mounting on a stable base frame ensures a quick installation and makes mobile use possible. Hfsdpfx Agecnz U Eo Djr Briquette diameter (mm) 50 Throughput capacity up to (kg/h) 50 (depending on material) Hydraulic motor (kW) 5,5o Screw motor (kW) 0,55 Oil quantity (litres) 100 Weight (kg approx.) 800 Outstanding features at a glance Hydraulics with separate oil tank: temperature-controlled hydraulic unit, complete valve control, pump motor for long running times Briquette length monitoring: regulates the length of the briquette to a constant level Pressing area wear bush: Prevents wear in the pressing area Location: Ex works - free loading

Condition: excellent (used), Year of construction: 2020, New hydraulic heating platen press Manufacturer: ITALPRESSE, Type XL/6 30-13 with gold-anodized plates Touch display control system - Electric heating platens 3,000 x 1,300 mm - Total pressing force: 90 tons - Number of heating plates: 2 pcs. - Number of levels: 1 - Cylinder stroke: 350 mm - Daylight opening: 350 mm - All-around loading possible - Number of hydraulic cylinders: 6 pcs. - Cylinder diameter: 85 mm Hfsdpfx Ajxgbxfeg Dor - Hydraulic unit power requirement: 3 kW - Electric heating plates made of solid hard aluminum with built-in heating wires - Heating capacity: 22 kW - High-pressure insulation plates - Working temperature: 90° C - Max. temperature: 120° C - Operating voltage: 400 V, 50 Hz - Safety specifications according to CE standard Standard equipment: - Movement of the press table with rack-and-pinion and parallel guides at 2 corners of the press table made from self-lubricating material - Electronic control unit with touch screen for machine control and monitoring - Digital timer for adjusting pressing time and automatic opening - Digital input and monitoring of pressing pressure - Digital timer for adjusting pressing time - Digital diagnostics and fault display - Safety circuit with two-hand operation - Safety pull cord - Safety support for lower press table Accessories included: - Touch Screen TS/400 - EFC electronic flatness control - Gold-anodized heating plates (Busse) Location: Ex stock - Immediately available -

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Lamella - carcass press with rapid traverse Hsdjiidm Njpfx Ag Defr Technical data: Lamella carcass press from our showroom; Working range: width from 150 - 2.500mm , height from 150 - 1.400mm; depth 700mm; - lamella press beam top with 6 elements, lamella press beam side with 5 elements - lamella press beam with practice-proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are 40 mm thick, coated continuous support plates - The pressing force of the pressing bars is infinitely variable electronically controlled by 2 potentiometers and adjusted via frequency converter, therefore the torque transmission is absolutely wear-free. - Pressing force for horizontal press bars min. 500 daN (kg) to infinitely variable max. 2200 daN (kg) - Pressing force for vertical press bars min. 300 daN (kg) to stepless max. 2200 daN (kg) - Including option: Rapid traverse speed for fast positioning of the press bars, controlled by automatic workpiece recognition with sensors in the press bars, press speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Jog mode for precise positioning of the two pressing beams e.g. for low pressing forces, drawers and carcasses 45 degrees. Simple operation via 6 separate pushbuttons, freely adjustable pressing time preselection with automatic opening, loading height 300 mm. Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2024, Weima Briquetting Press TH 714 The TH 714 machines are designed for plants with required throughput rates of up to 150 kg/h. The stable press housing enables the production of high-strength briquettes - from materials such as wood, polystyrene, foams, light metals, paper or biomass. Numerous additional options can be implemented, e.g. oil cooling for multi-shift operation. All machines are available as left- or right-hand version. Mounting on a stable base frame ensures fast installation and makes mobile use possible. User-friendly operation thanks to Siemens PLC control Hfodpfx Agsil Hgge Dor In order to live up to our performance promise, we design and produce all control cabinets ourselves at our Ilsfeld site and equip them with well-known international components. This guarantees highest quality with compact design. The used PLC-control from Siemens is perfectly adapted to the requirements of the briquetting process. Impurity-resistant screw conveyor due to cardanic suspension The screw conveyor, which transports the material into the pre-compressor of the briquetting press, is suspended on a cardan joint. This prevents interfering materials from causing damage to the screw conveyor. As is so often the case, however, it always depends on the specific application which suspension is chosen. For metal applications, for example, we often recommend rigidly mounted screws. Briquette diameter (mm): 70 Throughput capacity up to (kg/h): 150*1 Hydraulic motor (kW): 11 Oil quantity (liters): 250 Weight (approx. kg): 1100 Location: Ex stock 54634 Bitburg - immediately available - subject to prior sale

Condition: new, Year of construction: 2024, Compact design, high reliability and an excellent price-performance price-performance ratio: these are the advantages of this machine machine, which is perfectly suitable for briquetting materials such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a sturdy base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044x1044 mm hopper height: 1010 mm Hfedpfx Asbtnf Ejg Djr hopper capacity: 1,1 m³ driving power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil capacity (l) 100 Weight (kg) 530 Equipment: Press Powerful press mechanism with low-wear, chrome plated tongs Precompressor with end-position-suspended cylinder and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Tank with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette quantity monitoring Automatic On - Off Location: 54634 Bitburg

Year of construction: 2025, condition: as good as new (ex-display), Vacuum - membrane press VP - Series are the optimal solution for woodworking. VP 3000 is equipped with the heating technology, which shortens the drying time of the glue, so that the efficiency is higher. Possible applications: Veneer / form gluing / wrapping... Coating of different profiles (veneer,paper, plastic...) Wood bending: production of bent and layer-glued components The heating system is equipped with temperature control Rubber membrane 2,5 mm Table top is made of plastic 12 mm Oil-free Becker vacuum pump 25 m3/h The control system of the vacuum / tank capacity 15 l working area: 3000x1500mm Heating system temperature: Max. 60 degrees C heating system: KW 4,5 Pump capacity: KW 0,75 Vacuum pump flow rate: 25 m3/h Rubber membrane Dimensions outside: 3100 x 1650 x 1600 mm Hfsdpsdwh E Aefx Ag Der Weight: 450 kg Machine is equipped with a chassis. Location: From warehouse 54634 Bitburg - free on truck -

Condition: like new (used), Year of construction: 2025, operating hours: 1 h, Super special price, as it was on display at our in-house exhibition. Operating hours: 2 Available immediately - subject to prior sale If gone - then gone Compact design, high reliability and an excellent price-performance ratio excellent price-performance ratio: these are the advantages of this machine, which is perfect for briquetting materials such as wood such as wood, polystyrene, foam or paper. Special feature: the screw pre-compaction, which guarantees a guarantees high briquette quality. For quick and easy installation, the C 140 is mounted on a stable base frame. mounted on a stable base frame Overall dimensions: 1900 x 1410 mm Hopper opening: 1044 x 1044 mm Hopper height: 1010 mm Hopper capacity: 1.1 m³ Drive power: 4 kW Briquette diameter (mm) 40 Throughput capacity (kg/h) 30-40 Hydraulic oil volume (l) 100 Weight (kg) 530 Equipment: Press Powerful pressing mechanism with low-wear, chrome-plated tongs Pre-compressor with end-sensitive cylinder Hsdpfotnz Hbex Ag Dofr and screwed cover Control box with PLC control Hydraulics Separate oil tank with pump motor and valve control Safety switch for oil temperature Container with agitator and gear motor Screw channel with discharge screw and gear motor gear motor Accessories: Briquette length monitoring Automatic on - off Location: 54634 Bitburg