Used eccentric presses single column over 100t for sale (110)

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece Bedpfxsu Rwa Ij Aknjlp - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, Year of construction: 1980, Technical details: Pressure: 160 t stroke: 20-160 mm throat: 400 mm ram adjustment: 120 mm no. of strokes: 71 Hub/min daylight dimension : table/slide up: 720 (bei Hub 160mm) mm daylight dimension : table/slide low: 560 (bei Hub 160mm) mm ram surface area: 900 x 660 mm distance between columns: 500 x 450 mm table surface area: LxBxØ: 1200 x 750 x 100 mm total power requirement: ca. 23.0 kW weight of the machine ca.: ca. 15,0 t dimension machine xH: 2,7 x 1,5 x 3,45 m dimensions electric cabinet LxWxH: 2,0 x 0,65 x 2,15 m Operation via control panel/operator stand/foot control and hand-held control unit The press can be offered with two options. Bedpou N A U Ijfx Aknelp 1st option: Sold as is, not connected, not complete, not functional. 2nd option: The baler will be refurbished, all parts will be exchanged, replaced and puddled. The press will be set up again. For inquiries about this press, please select your offer option! in progress. *

Condition: as good as new (ex-display), Year of construction: 2026, Machine to be exhibited at EUROBLECH 2026: Trade fair – special price! Bljdpfez Hkh Hox Aknop Press force: 1600 kN Stroke: 15 – 110 mm Stroke rate: 30 – 65 /min Ram adjustment: 95 mm Table: 1,100 x 700 mm Ram: 900 x 500 mm Installation height: 460 mm Weight: 12,000 kg Connection: 15 kW Includes: - Fully automatic stroke adjustment, hydraulic overload protection, motorized ram adjustment - Frequency inverter, central lubrication, light curtain - Control system: SIEMENS S7/1500

Condition: good (used), Year of construction: 1974, pressing force: 100 t, Model: OB1 Pressing force: 100Tm Torque: 3500kg Plate thickness: 10mm Pusher slider: 5-159mm Distance between table and spindle/pusher: 530mm Max. spindle/pusher travel: 130mm Strokes per minute: 53 Bedpfx Aksudwr Uonolp

Condition: used, Year of construction: 1980, Technical details: Bjdsu N A Uuopfx Aknjlp pressure: 400 t stroke: 40 - 140 mm strokes / minute continous: 32 throat: 400 mm dayligth: min/max: 450/590 mm ram adjustment: 125 mm table-size: 1250x750 mm height over floor: 1130 mm total power requirement: ca. 31,5 kW weight of the machine ca.: 23,0 t machine dimensions LxWxH: 3,7 x 1,7 x 3,9 m dimensions electric cabinet LxWxH: 1,0 x 0,7 x 2,1 m further details: - clamping plate : L x W x H : 1260 x 760 x 100mm - with draw cushion device force 250kN, travel approx. 83mm - control via panel i.D. *

Condition: good (used), Year of construction: 2002, functionality: fully functional, power: 12 kW (16.32 HP), pressing force: 120 t, table width: 610 mm, table length: 850 mm, total length: 19,000 mm, total width: 19,000 mm, overall weight: 8,500 kg, installation height: 300 mm, to visit under power Blsdpforwlxtsx Aknsp

Condition: used, Year of construction: 1983, Technical details: Bsdpou Nfizefx Aknslp pressure: 100 t stroke: 20 fest mm no. of strokes: 55 Hub/min throat: 355 mm mortise hole in ram: Ø 36 mm table surface area: 900x640 mm ram adjustment: 150 mm clamping surface ram: 500x415 mm height over floor: 800 mm biggest distance between table & ram: 390 mm passage opening in table: Ø 330 mm total power requirement: 11 kW weight of the machine ca.: 7,5 t dimension machine xH: 1,46x1,58x2,57 m transport dimensions LxWxH: 1,9x1,6x3,1 m Press is without electric cabinet, optional construction of electric cabinet possible. *

Condition: used, Year of construction: 2018, Nominal pressing force: 4,000 kN Ram stroke, adjustable in increments: 30 ... 160 mm Ram adjustment: 180 mm Throat depth: 515 mm Strokes per minute (idle): 45 / min Option: Infinitely variable stroke rate: 10 … 60 / min Die installation height at maximum stroke, bottom dead center, and ram fully raised: 660 mm Table clamping surface (W x D): 1,700 x 1,000 mm Table height above floor: 1,005 mm Ram clamping surface (W x D): 1,100 x 800 mm Pin bore in ram: 65 mm Main motor power: 45 kW Approximate machine height: 4,325 mm Bsdpfx Akow Rbxzjnjlp Machine weight: 33,000 kg Control system – Press safety control with redundant design and self-diagnosis, featuring plain text status and error display Infinitely variable stroke rate in the range of 10 ... 60 strokes/minute via ABB frequency inverter Control variant: TFT color touchscreen including electronic cam controller with die management and die protection, with color touchscreen visualization, SIEMENS PLC S7-300, die data management, counting systems, data transmission via Profibus Fully automatic stroke adjustment / ram adjustment Rigidly welded tie rods, clear distance between tie rods: 1,345 mm Swiveling main control console Non-contact safety guard – BWS brand LUMIFLEX, mounted at the front of the machine table or die area, installed on the tie rods

Condition: used, Year of construction: 1983, Technical details: pressure: 100 t stroke: 20 fest mm no. of strokes: 55 Hub/min table surface area: 900x640 mm throat: 355 mm ram adjustment: 150 mm mortise hole in ram: Ø 36 mm clamping surface ram: 500x415 mm height over floor: 800 mm Blodpfx Akeu Nfi Ujnep biggest distance between table & ram: 390 mm passage opening in table: Ø 330mm mm total power requirement: 11 kW weight of the machine ca.: 7,5 t transport dimensions LxWxH: 1,9x1,6x3,1 m Press is without electric cabinet, optional construction of electric cabinet possible. *

Condition: used, Year of construction: 2007, pressure 200 t throat 510 mm stroke 16 - 160 mm ram - range of adjustment 120 mm table surface area 1500 x 1000 mm table height over floor 900 mm hole in the table 800 x 250 mm ram surface 1000 x 700 mm tool hole in ram 65 x 110 mm T-slot - width 28 mm number of strokes adjustable 30 - 120 min oil volume Hydraulikaggregat 5 l daylight, max. stroke above - ram adjustment above 600 mm daylight (stroke down, ram adjustment above) 440 mm total power requirement 32,2 kW Bsdpfx Akevbk Rwenjlp weight of the machine ca. 24 t dimensions of the machine ca. BxTxH 2,85 x 3,1 x 3,65 m - hydraulic clutch - fixed table - hydraulic overload protection in the ram - hydraulic connecting rod clamping - Motorized ram height adjustment 120 mm with digital display set ram height, rapid and slow speed - fully automatic stroke adjustment, adjustment range 16 - 160 mm - Ram weight compensation - electronic OT correction - Planetary gears - Oil circulation central lubrication - Separate control panel with SIMATIC S7/300 screen control - Press force measuring device - Reversing switch (return) - additional operating mode “set-up-creep speed” - electric stroke counter - electrical preset counter - electrical travel limitation of the connecting rod journal - electronic cam switch - continuously variable drive (frequency controlled) - 2 sockets - Clamping plate - Temperature monitoring main bearing / support bearing / connecting rod bearing - Operating hours counter - Oil cooler - Set of oscillating elements Additional equipment: Electronic roller feed ebu EVX 500 Passage width: 10 - 500 mm Material cross section: max. 1,600 mm² Material thickness: 0.2 - 5.0 mm Number of reels: 2 Roller diameter: 100 mm Intermediate ventilation: up to over 300 l/min Feed length: 1.0 - 9,999.9 mm Feed speed: max. 150 m/min

Condition: used, Year of construction: 1981, Technical details: pressure: 250 t slide stroke: 36...126 mm throat: 400 mm ram adjustment: 110 mm surface area of ram: 630 x 500 x 100 mm dayligth: 400 mm Table dimensions: 1000 x 750 x 100 mm Bodpfxsu Nfkle Aknslp table height over floor: 1000 mm total power requirement: 23,0 kW weight of the machine ca.: 13,5 t dimensions electric cabinet LxWxH: 1,1 x 0,7 x 1,3 m dimension machine xH: 3,0 x 1,3 x 3,3 m further details: - control via 2 hand control console or with foot pedal - foot plates Ø 220mm accessory: - column punch device *

Condition: used, functionality: fully functional, ERFURT PRESS 250t Blodpfov Hqacex Aknep

Condition: used, Manufacturer: Müller Stanz- und Umformtechnik GmbH & Co. KG Type: PMLE250x1700 R-HK Machine No.: A05036-02 Year of manufacture: 2006 Machine type: Eccentric press Press force: 2500 kN Press force: 250 t Stroke rate: 20–120 min⁻¹ Stroke: 25–125 mm Ram adjustment: 100 mm Voltage: 400 V Motor power: 55 kW Connected power: 100 kW Bodpfx Akozrz Ecsnolp Weight: 47,000 kg Draw cushion: No Condition: Used Machine is leaking hydraulic oil Several leaks are present in the hydraulic system Tension pins for the ram adjustment have been deactivated due to the hydraulic leaks Sold without conveyor system Videos available upon request Location: Freiburg

Condition: used, Year of construction: 1985, Technical details: pressure: 100 t no. of strokes: 35-100 Hub/min throat: 360 mm ram adjustment: 20-130 mm ram surface area: 750x550 mm clamping plate on table: 1000x640 mm adjustment of stroke: 90 mm Bledpfxou Nfh Dj Aknsp passage between the columns longitudinal/sideways: 610x500 / 440x550 mm daylight dimension : table/slide low: 300 mm total power requirement: 17,5 kW weight of the machine ca.: ca,7,0 t dimension machine xH: 1,9x1,4x2,7 m - there are 5 T-slots lengthwise on the ram plate - centre hole = 50mm This press is currently for sale without controls. Optional on customer request completion possible. i.D. *

Condition: used, Year of construction: 1972, machine/vehicle number: 1171, Capacity: 160 ton Throat depth: 350 mm Ram stroke: 20 - 140 mm Slide adjustment: 75 mm Shut height (stroke down, adjustment up): 740 mm Table surface area : 1000 x 680 mm Slide area: 600 x 300 mm Number of strokes: 50 s.p.m. Bedpouqdwxjfx Aknelp Required power: 15 kW Weight of machine approx.: 12 ton Standard configuration Machine included: - Fence HS decoiler M 15 / 500 - built in 2009Material width 15 - 500 mmCoil weight 1,5 tCoil exterior diameter 1400 mmCoil interior diameter  380 - 530 mm HS straightener RME 40 - 9 - built in 2009 Material thickness 0,4 - 2 mmNumber of feeding rolls 2 piecesNumber of straightener rolls 9 piecesDiameter of straightener rolls 61,9 mmDiameter of feeding rolls 61,9 mmFeeding speed 40 m / minFeeding length  0 - 9999,99 mm Extended machine accessories The machine was converted to SIEMENS S7 in 2009.

Condition: refurbished (used), Year of construction: 2000, functionality: fully functional, Equipment: documentation/manual, TECHNICAL CHARACTERISTICS: Press Model: T160 CNR6 Serial number: 160/0/46/00 Year of construction: 2000 Nominal force: 1600 kN Weight: 13,800 kg Nominal number of strokes: 55 C/min. Min./max. number of strokes: 10/55 C/min. Max. number of insertions: 17 C/min. Min./max. clutch pressure: BAR 4.0÷5.5 Max. stop time: 0.22 s Safety distance: 355 mm. Energy (i=15% nominal strokes): 14,500 KJ Min./max. stroke: 10/200 mm Ram adjustment: 110 mm. PMI high adjustment: 430 mm Maximum extraction stroke: 60 mm Work surface dimensions (H, D, L): 78/750/1250 mm Ram dimensions (D, L): 600/850 Shank diameter: 60 mm Protrusion from the center: 370 mm Maximum mold size: 600/850 mm Maximum mold head weight: 344 daN Operating air pressure: BAR 5.5÷6 Stop position: TDC Voltage: V 380 Frequency: 50Hz Auxiliary voltage: V 24 Bjdpfxewaiw Se Aknslp NEW COMPONENTS INSTALLED: • Safety guards with safety keys; • Clutch plates; • Clutch pins and brite; • Flywheel bearings; • Flywheel oil seals; • Stroke change nose; • Balancing cylinder gasket kit; • Air pressure gauges; • Electrical panel; • Inverter (speed variator); • Motor; • Motor pulley; • Work surface revived on CNC machine Supplied with six (6) months warranty, technical documentation and CE conformity Twelve (12) months electrical panel warranty.

Condition: used, Year of construction: 1978, pressure 125 t throat 340 mm stroke 20 - 160 mm no. of strokes 55 /min distance table/ram, max. stroke up, adjustment up 480 mm table surface area 1000 x 660 mm table height over floor 730 mm ram surface 600 x 300 mm Bsdpjzrpqaefx Aknolp ram adjustment 75 mm power requirement 8,5 kW weight 7,8 t dimensions (WxDxH) 1,4 x 2,8 x 2,7 m with motor, back gears, pneumatic clutch, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, fix table, two-hand and foot operation

Condition: used, Year of construction: 1976, pressure 400 t stroke 30 - 300 mm no. of strokes 55 /min throat 500 mm passage to the back 800 mm dayligth 950 mm table surface area 1580 x 1000 mm Blodpozrpqgefx Aknsp hole in the table 400 x 400 mm table height over floor 800 mm ram surface 1000 x 720 mm ram adjustment 125 mm power requirement 37,0 kW Weight 25,0 t dimensions (WxDxH) 2,5 x 3,1 x 5,1 m with motor, pneumatic clutch/brake combination, hydraulic overload protection in ram, semi-automatic stroke adjustment, motorized ram adjustment, pneumatic counterbalance in ram, fix table, motorized central lubrication, two-hand operation

Condition: used, Year of construction: 1983, pressure 100 t throat 375 mm stroke 20-125 mm no. of strokes 60 Hub/min ram - range of adjustment 80 mm table surface area 920x660 mm ram surface 700x450 mm Bodpfsxh Swhex Aknslp hole in the table Ø90 mm tool hole in ram Ø50 mm weight of the machine ca. 8 t dimensions of the machine ca. 2100x1500x3300 m

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, pressing force: 4,000 t, stroke length: 180 mm, throat depth: 500 mm, overall weight: 28,000 kg, controller model: Siemens S7-300, The machine underwent a major overhaul in 2007! The following modifications were carried out on the single-column eccentric press PEE 400: Conversion of the press drive to an adjustable drive with 15-45 strokes of the press ram Conversion of the clutch and brake to a pneumatically actuated Ortlinghaus clutch-brake combination Adjustment of the pinion shaft, flywheel, and bearing cover to the pneumatically actuated clutch-brake combinations Replacement of the rolling bearings for the pinion shaft and flywheel bearing Replacement of all sealing elements and wear parts for the drive Replacement of the seals for the compensator cylinder Replacement of the V-belts for the flywheel drive Replacement of the entire electrical control system Installation of a stroke adjustment mechanism Modification of the safety device Mounting of a tie rod to reduce frame deflection under press force Replacement of the worm gear for ram adjustment, pressure spindle, spindle nut, and pressure ring Refurbishment of the ram guide rails Replacement of the die plate and its support Hydraulics Pneumatics Lubrication Hydraulic pull-down cushion in the press table Tool mounting arms for attaching the press tool Tool lever strips in the table TECHNICAL DETAILS Pressing force: 4,000 kN Adjustable stroke: 30–180 mm Adjustable stroke rate per minute (continuous operation): 15–45 /min Ram adjustment: 150 mm Overhang: 500 mm Ram area (width × depth): 1,200 × 800 mm Table area (width × depth): 1,600 × 1,000 mm Maximum distance between table and ram area: 625 mm MACHINE DETAILS Control: Siemens S7-300 Motor power: 55 kW Motor speed: 1,500 rpm Hydraulic pull-down cushion Piston diameter: 110 mm Piston rod diameter: 90 mm Effective piston area: 95 cm² Pull-down cushion diameter: 230 mm Adjustable counterforce: 10–250 kN Usable pull-down cushion stroke: 90 mm Speed of the pull-down cushion during extension: max. 65 mm/s Bodpfx Aszmfnqeknolp Hydraulic system Flow rate of the pull-down cushion pump: 29 l/min Drive power of the main pump: 7.5 kW Oil capacity in the tank: 250 l Flow rate of the circulation pump: 65 l/min Drive power of the circulation pump: 1.5 kW Operating pressure for clutch and brake: 5 bar Operating pressure for ram weight compensation: 5 bar Total machine weight: 28,000 kg

Condition: used, Year of construction: 1980, Pressure capacity 1,250 kN Adjustable stroke 20 - 140 mm Stroke rate 70 1/min. Bjdpform Ntpjx Aknelp Further data and pictures on request the press is currently not functional and must be mechanically and electrically overhauled

Condition: good (used), Year of construction: 1988, functionality: fully functional, power: 11 kW (14.96 HP), input voltage: 400 V, pressing force: 160 t, total length: 2,310 mm, total width: 1,270 mm, total height: 2,590 mm, overall weight: 10,150 kg, year of last overhaul: 2023, For sale: Used ZTS LE 160 C eccentric press, year of manufacture 1988. The machine is in good technical condition, except for the paint coating. All control solenoid valves were replaced in February 2023. The machine has been seldom used for a long period and has been in our possession for 20 years. Machine number: 2291286 Machine type: LE 160 C Year of manufacture: 1988 Maximum pressing force: 1600 kN Power: 11 kW Bjdpfx Akex Rcgzenolp Voltage: 400 V Weight: 10,150 kg Total length: 2310 mm Total width: 1270 mm Total height: 2590 mm If you have any questions or need further information, please send a message or contact us by phone.

Condition: used, Year of construction: 1990, EBU 160t TYPE HK160F PRESSURE: 160t UP TABLE DIMENSIONS: 1000x500mm DOWN TABLE DIMENSIONS: 1200x800mm STROKES PER MINUTE: 80 STROKE LENGTH: 20-200mm DAYLIGHT: 600mm POWER: 15kw WEIGHT: 17,500 kg Bedpfozktzyox Aknelp THE MACHINE IS IN EXCELLENT CONDITION AND READY FOR LOADING.

Condition: used, Year of construction: 1990, ECCENTRIC PRESS GIZELIS 200t PRESSURE 200t TABLE DIMENSIONS 1000x660 mm STROKE 17-230 mm POWER 11 kW WITH HYDRAULIC CLAMPING SYSTEM Bjdpfsx N Sqysx Aknolp

Condition: used, Year of construction: 1982, pressure 150 t throat 520 mm stroke 30 - 200 mm no. of strokes 15 - 60 /min distance table/ram, max. stroke up, adjustment up 650 mm table surface area 1600 x 1000 mm hole in the table 1040 x 140 mm Blsdpfx Aezrprkjknop table height over floor 1000 mm passage to the back 1000 mm ram surface 1400 x 800 mm ram adjustment 120 mm power requirement 20,0 kW weight 27,5 t dimensions (WxDxH) 2,3 x 2,75 x 4,5 m with infinitely variable drive, pneumatic clutch/brake combination (make Ortlinghaus), hydraulic overload protection in ram, pneumatic counterbalance in ram, semi-automatic ram adjustment