Eccentric Press - Single Column

EBU HK 200 FR

Condition: used, Year of construction: 1984, turning diameter over cross slide: 1,600 mm, turning diameter: 2,000 mm, turning diameter over bed slide: 2,000 mm, turning length: 35,000 mm, workpiece weight (max.): 63,000 kg, Center Lathe SKODA - SUT 200 TD MACH-ID 9446 Manufacturer: SKODA Model: SUT 200 TD Year of manufacture: 1984 Tandem construction on one bed, with left and right headstocks Faceplate double tailstock left and right Double carriage Steady rest included Roller rest included Operator panel with scales requires attention and replacement Motorized tailstock for each side (left and right) 3-bed way design Torque on chuck: 160,000 Nm Minimum turning diameter: Ø 315 mm Industries served: - Shipyards - Propeller shaft manufacturing - Hydraulic cylinder shafts - Camshafts - Defence & Aerospace - Rolls and shafts for steel mills - Crankshafts Specifications Metric / Imperial Turning length: 35,000 mm Swing over bed: Ø 2,000 mm Swing over carriage: Ø 1,600 mm Fedeynky Aspfx Ad Iepi Spindle power: 75 kW Bed width: 1,600 mm Quill diameter: Ø 400 mm Quill stroke: 250 mm Max spindle speed: 180 rpm Feed X-axis: 5,000 mm/min Feed Z-axis: 5,000 mm/min Workpiece weight: 63,000 kg Approximate dimensions: Length: 42,000 mm Width: 3,250 mm Height: 3,250 mm Weight: 158,000 kg Please note: The information on this page has been provided to the best of our knowledge and, where possible, obtained from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, they do not constitute representations or contractual terms. We recommend verifying all important details.

Condition: used, cone distance min./max. 0-108 mm Pitch angle min/max 5°/84° Control GE Fanuc Series 0-GC Pitch diameter (1:1 ratio) 152 mm pitch diameter (10:1 ratio) 216 mm Diametral pitch (finest/coarsest) 1.3/8.5 Mod. Fjdpfsyh Rmmsx Ad Ijpi Face width gear wheel max. 35 mm Knife spindle - Speed range 41-121 U/min working spindle speed range 0-33.33 U/min weight 9025 kg dimensions of the machine ca. 2707 x 2720 x 2200 mmxmmxmm Equipment/accessories: - 18-piece cutter set - Chip conveyor - Technical documentation

Condition: good (used), CHARACTERISTICS Fedpfxsr I Aykj Ad Iopi Plate diameter ⌀; 3200 mm Maximum turning/turning diameter ⌀; 3300 mm - With upright forward; 3300 mm - With upright set back; 5600 mm Min. turning/turning diameter ⌀ - With advanced upright; 800 mm - With upright set back; 3100 mm Max turning height; 750 mm Control; FAGOR 8025 Spindle RPM (2 ranges); - 0,5 - 10 rpm - 10 - 40 rpm Motor Power; 80 hp Maximum table load; 30.000 kg

Condition: good (used), Year of construction: 1995, machine/vehicle number: 0540/98, functionality: fully functional, Manufacturing number: 0540/98. Year of manufacture: 1998 ,. Capacity: 400 tons. Stroke length: 300 mm. Stroke: 10-40 / min. Slide adjustment 300 mm. Installation height: 700 mm. The table measures 1600 x 1300 mm Net weight: 45 tons. Gable opening: 1600 mm. Exterior dimensions 2 x 3 x 6 meters. Control system MEAB. Coil feeder / straightener iRON RNE 50B / 11. Decoiler iRON SA6000 max 700 mm. Fpodoicbbzepfx Ad Iji

Condition: new, Year of construction: 2026, Recirculating chamber furnace, electric, brand new, delivery time 16 weeks - Maximum temperature: 300°C - Internal dimensions (W x D x H): 2100 x 2100 x 2000 mm - Capacity: 8,820 liters - Eurotherm Nanodac controller/recorder with color touch display - 2 circulating air fans - Double door with safety door sensors - Over-temperature protection, Eurotherm 3216i - 2 fresh air fans - Automatic dampers - Electrical configuration: 400 V / 50 Hz / 3NPE - Increased heating capacity of approx. 70 kW - Temperature accuracy: +/- 6 K in the empty oven - Documentation and CE declaration of conformity - Electrical schematic with spare parts list Note: The oven floor is not insulated but is covered with stainless steel sheet. This allows unrestricted access with all track widths. Alternatively, an insulated floor can be offered (with entry rails to be defined by the customer). Fedpfxev Hg Eus Ad Iopi We offer new and used industrial furnaces, which we can also modify and upgrade according to customer requirements. Keywords: oven, ovens, drying oven, industrial furnace, drying cabinet, heating oven, heat cabinet, recirculating oven, chamber oven, heating chamber, chamber recirculating oven, tempering oven, annealing oven.

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm Fodpfjfx Hv Hex Ad Iopi clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: used, fuel type: diesel, Manufacturer: CATERPILLAR Type: V 250 Capacity: 12000 kg Lift Height: 3710mm Boom height: to insert moulds of fork length: 1400mm width: 2550mm Fedpfxec Urcis Ad Ispi Overall length: 6400mm

Condition: new, Year of construction: 2025, turning diameter over cross slide: 250 mm, turning length: 730 mm, turning diameter: 500 mm, spindle speed (max.): 1,800 rpm, CNC lathe machine CK 6150 with flat bed Fodpfx Adexdmgvo Ispi We offer a new CNC lathe machine model CK6150. We use this machine in our production and you can see it in operation before ordering. The CK 6150 lathe has a flat bed and hardening guides, which ensures a long period of operation of the equipment. The machine is equipped with a CNC system, the GSK CNC system is installed as standard. Optionally, the machine can be equipped with a Fanuc or Siemens CNC system. The machine can have a tool holder for 4-6 or 8 tools, depending on the customer's wishes. It is possible to install a hydraulic chuck on the machine, which will greatly simplify the process of installing parts on it and a hydraulic tailstock. The CK 6150 lathe can be equipped with additional supporting frame for more accurate manufacturing of long parts. Technical specifications: Model CK 6150 x 1000 Maximum workpiece diameter over bed 500 mm Maximum workpiece diameter over support 250 mm Maximum workpiece length 1000 mm Maximum turning length 730 mm Spindle bore diameter 82 mm Spindle speed 150-1800 rpm Engine power 7.5 kW Mechanical chuck (hydraulic optional) Chuck size 250 mm. 4-position tool holder (6 or 8 optional) Maximum tool size for tool holder 25x25 mm Machine weight 2700 kg Machine dimensions 2650×1700×1820 mm We can also supply lathes CK 6140, CK 6150 and CK 6160 with other dimensions of the working part: CK 6140 dimensions of the working part 550/750 mm CK 6150 dimensions of the working part 1000/1500/2000 mm CK 6160 dimensions of the working part 1000/1500/2000 mm CK 6152E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6185E dimensions of the working part 1000/1500/2000/3000/4000 mm CK 61100E dimensions of the working part 1000/1500/2000/3000 mm CK 61125E dimensions of the working part 1000/1500/2000/3000 mm

Year of construction: 2017, condition: ready for operation (used), - USED - FIBER LASER CUTTING MACHINE FOR TUBES WITH LOADING/UNLOADING SYSTEM MIN CIRCULAR SECTION: ø 25 mm MAX CIRCULAR SECTION: ø 355 mm MAX SQUARE SECTION: 260 X 260 mm MAX RECTANGULAR SECTION: 300 X 200 mm MAX ADMITTED LOAD: 100 Kg/m Fpsdpfx Adsx E Eiho Isi SOURCE: IPG YLS-4000 ; 4000 W CONTROL UNIT: SIEMENS 840D WEIGHT: 12500 Kg NOTE: AUTOMATIC LOADING 3-12.5 mt; AUTOMATIC UNLOADING 12.5 mt; 3D CUTTING HEAD; CAPACITIVE SENSOR; AUTOMATIC ADJUSTMENT

Condition: good (used), Year of construction: 1976, Centre lathe ZERBST - DPS 1800 MACH-ID 581 Make: ZERBST Type: DPS 1800 Year: 1976 Swing over bed Ø 1600 mm Swing over cross slide Ø 1250 mm Swing in the gap Ø 2100 mm Bed width 1400 mm Fjdpfswvir Isx Ad Ijpi Power 35 kW Speeds / ranges 180 Rpm