Condition: ready for operation (used), functionality: fully functional, TECHNICAL DETAILS Briquetting Machine Iedpfx Abezr Efaeneba Diameter of briquetting drums: 800 mm Working width of briquetting drums: 900 mm Rotational speed of briquetting drums: 8 rpm Number of working rollers: 4 pieces Mixer Drum diameter: 1,500 mm Number of mixing blades: 4 pieces Rotational speed of mixer: 17.8 rpm Screw Conveyor Length: 4,000 mm Width: 850 mm Rotational speed of screw shaft: 36.6 rpm MACHINE DETAILS Suitable materials: anthracite coal, lignite, wood, bulk materials Design: Supporting structure including base housing for briquetting unit, mixer, and screw conveyor EQUIPMENT Belt conveyor for separating fine particles and non-briquetted material Single-shaft paddle mixer Driven screw conveyor 4 additional jackets for preparing further dies

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, Weinig Dimter Profipress C 2800 P - 6 m gluing press Manufacturer: Weinig Dimter Model: Profipress C 2800 P - 6 m Year of manufacture: 2009 Condition: Very good Machine description: For sale: Weinig Dimter Profipress C 2800 P - 6 m wood gluing press, year 2009, designed for the production of glued wooden panels and elements made of soft timber. The machine was developed for efficient production using PVAC glue in D2 / D3 class and allows processing of material within specified width, thickness and input length ranges. According to the documentation, this model can process timber with widths from 30 to 80 mm, thicknesses from 15 to 40 mm and input lengths from 2100 to 2800 mm. The machine allows the production of panels with variable widths from 600 to 1200 mm. For short lengths, the collecting distance range is 700 to 1400 mm. The output is up to 10 to 15 infeeds per minute, depending on the entrance width. The Profipress C 2800 P - 6 m is intended for processing soft timber. The permitted bending tolerance is maximum 5 mm per meter. The documentation also specifies recommended operating conditions, including room temperature from 15 to 30 degrees Celsius and air humidity in the range of 40 to 65 percent. Technical data: - Model: Profipress C 2800 P - 6 m - Year of manufacture: 2009 - Performance: max. 10–15 infeeds/min, depending on entrance width - Timber width: 30–80 mm - Timber thickness: 15–40 mm - Timber entrance length: 2100–2800 mm - Collecting distance for short lengths: 700–1400 mm - Panel width: 600–1200 mm - Timber type: soft timber - Permitted bending: max. 5 mm/m - Glue type: PVAC D2 / D3 - Recommended room temperature: 15–30°C - Recommended air humidity: 40–65% Features and advantages: - Press designed for glued panel production - Machine from the renowned Weinig Dimter brand Ibodpsyvgiaofx Abnoa - Output up to 10–15 infeeds per minute - Possibility to produce panels with variable width - Suitable for processing soft timber - Works with common PVAC D2 / D3 glue - Industrial application for woodworking and production plants

Condition: excellent (used), Year of construction: 2007, Catalog number: 7809 TECHNICAL DATA - Pressing force: hydraulic - Briquette shape: round Ijdpszu Sxxefx Abnsba - Briquette diameter: 70mm - Hopper diameter: 900mm - Automatic machine operation - Inspection window in the machine hopper - Equipped with an additional oil heater - Motor: 5.5kW - Dimensions (L/W/H): 1600x1200x1500mm - Weight: 685kg ADVANTAGES - Unpainted - Made in Italy - Equipped with an additional oil heater - Used briquetting machine - Very good condition Net price: 36,900 PLN Net price: 8,786 EUR, depending on the exchange rate of 4.20 EUR (Prices may vary due to exchange rate fluctuations)

Condition: used, Dimensions: approximately 2500 x 1200 x 600 mm, semi-hydraulic, with electro-motorized adjustment of the press wall. Ibsdozd Hm Nepfx Abnja Storage location: Nattheim.

Year of construction: 2007, condition: used, Membrane press with Becker pump Manufacturer: Columbus Type: Vakuform Standard Iodpfx Abezu Am Hensba Year of manufacture: 2007 Technical data - 750 watts, 230/380V, 50 Hz - Tank capacity: 200 l - Suction capacity: 25 m3/h - Vacuum: max. 0.85 bar - Working area: 2980 x 1350 mm Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is not binding.

Year of construction: 2013, condition: used, Membrane press Manufacturer: Columbus Type: Vacuum forming Year of manufacture: 2013 Technical data Ibjdpfx Aozu Amyebnja - Working area: 1980 x 1350 Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2015, condition: used, Membrane press Manufacturer: Columbus Type: Multimat Year of manufacture: 2015 Technical data - Press table: 3000 x 1400 mm Ibjdpezu Ammefx Abnja MULTIMAT - Membrane press table Mobile table with a pivoting heating hood and membrane frame High-performance vacuum pump TF 40, final pressure adjustable up to a maximum of 900 mb (9 t/m²) Pneumatically pivoting film fixing frame Usable membrane frame incl. highly elastic silicone membrane (700% elongation) Aluminum heating hood, fully insulated, continuously adjustable from 0 to 140 °C Digital differential pressure control Entire system (incl. vacuum pump) maintenance-free Electrical connection (incl. heating hood): 10 kW, 400 V, 50/60 Hz Dimensions: External dimensions: 3200 mm x 1600 mm Usable area (without membrane frame): 2800 mm x 1200 mm Usable area (with membrane frame): 2750 mm x 1150 mm Table / working height: 900 mm Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Year of construction: 2012, condition: used, Membrane press with Becker pump Manufacturer: Columbus Type: Vakuform Standard Year of manufacture: 2012 Technical data - 750 watts, 230/380V, 50 Hz - Boiler capacity: 200 l - Suction capacity: 25 m3/h - Vacuum: max. 0.85 bar - Working area: 2980 x 1350 mm Ijdpezu Amgofx Abnoba Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2018, condition: used, - Heating plate format (mm): 2850 x 1550 - Total pressing force (kN): 2400 - Maximum operating temperature: 180 degrees Celsius Vacuum press with 3 paternoster magazines Manufacturer: Wemhöner Type: Variopress - Basic 1000S Year of manufacture: 2018 Technical data Heating plate format (mm) 2850 x 1550 Design of the electric heating plate: Aluminum heating plate on top Total pressing force (kN) 2400 Ibsdozuz Euopfx Abnea Maximum chamber pressure (bar) 6 Maximum operating temperature 180 degrees Celsius Maximum batch or workpiece size (mm) approx. 2460 x 1180 Thermoplastic film as roll stock, film width: approx. 1430 mm Film thickness (mm) approx. 0.25 - 1 Chamber height (mm) max. up to 180 Connection values: Installed power (kW) approx. 46 Required air pressure (bar) approx. 8 Including 3 x paternoster magazines for film rolls Note: The technical data and descriptions are a copy of the order confirmation from that time. The data is for informational purposes only and is not binding.

Year of construction: 2013, condition: used, Membrane press table Ijdozuz Ehjpfx Abnsba Manufacturer: Columbus Type: Vacuum forming Year of manufacture: 2013 Technical data - Working area: 1980 x 1350 Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2012, condition: used, Membrane press Manufacturer: Columbus Isdozuz Ebopfx Abnsba Type: Vakuform Sonder Year of manufacture: 2012 Technical data - Must be connected to an external vacuum pump - 750 watts, 230/380V, 50 Hz - Boiler capacity: 200 l - Suction capacity: 25 m3/h - Vacuum: max. 0.85 bar - Working area: 2000 x 1350 mm Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 1996, condition: used, Baling press Manufacturer: HSM Type: 55.1VL Ijdpfszuz D Rox Abnsba Year of manufacture: 1996 Technical data - 4.0 kW motor - 18 t pressing force - 400 V / 50 Hz Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Year of construction: 2007, condition: used, Membrane press with Becker pump Manufacturer: Columbus Ibedozuz D Depfx Abnja Type: Vakuform Standard Year of manufacture: 2007 Technical data - 750 watts, 230/380V, 50 Hz - Tank capacity: 200 l - Suction capacity: 25 m3/h - Vacuum: max. 0.85 bar - Working area: 2980 x 1350 mm Note: The technical data and descriptions are copies of the original order confirmation. The information provided is for informational purposes only and is not binding.

Year of construction: 1997, condition: used, Baling press Manufacturer: HSM Type: HSM 75 VL Year of manufacture: 1997 Technical data: - 2.2 kW motor - 9 t pressing force - 400 V / 50 Hz Note: Iodpfx Ajzuz Dwjbnoba The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Year of construction: 2013, condition: used, - Press table: 3000 x 1400 mm Membrane press Manufacturer: Columbus Type: Multimat Year of manufacture: 2013 Technical data - Press table: 3000 x 1400 mm Iodpfezuz A Tex Abnsba Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2007, Heating plate press Manufacturer: OTT Iodpfx Abezuzxnonoba Type: Solid 16-32 Year of manufacture: 2007 Technical data Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Continuous press Manufacturer: Ligmatech Type: Optimat MDE 10 Year of manufacture: 2001 Ibedpfxjzuzxbj Abnoa Technical data Body dimensions - Length: 300 - 2500 mm - Height: 300 - 1300 mm - Depth: 120 - 600/800 mm - Pressing forces are generated electrically, both horizontally and vertically, and can be varied independently - Pressing forces are applied vertically via a pressure plate and horizontally via 3 pressure jaws each - Pressing takes place centered and on a zero line on the operator side Positioning of the pressure jaws: - Top pressure jaw with forced guidance on the top press, optionally lowerable via cylinder - Middle pressure jaw freely programmable and motor-driven - Bottom pressure jaw freely programmable and movable via a common drive with the middle pressure jaw Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. The press plates Ibjdpfx Abozuzw Djnsa consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1996, Continuous press Isdozuzwwjpfx Abnsba Manufacturer: OTT Type: 300-K-D0 Year of manufacture: 1996 Technical data Plate dimensions: 2550 x 1350 mm Hot water heating 6 pressure cylinders Total pressing force: 135 t Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is non-binding.

Condition: used, Year of construction: 2007, Lamination press Manufacturer: Dimter Type: PROFIPRESS L2500 Year of manufacture: 2007 Technical data Wood dimensions to be processed Wood width, panels: 30 - 150 mm Wood thickness: 11 - 60 mm Wood inlet length: 800 - 2500 mm Panel widths, variable: max. 1300 mm Specific pressing pressure for cross-sections of 2500 x 60 mm: up to 1.6 N/mm2 The pressing surface per press cycle must not be smaller than 100 cm2 Filling width of the press per cycle: min. 650 mm / max. 1300 mm Max. filling area of the press per cycle: 3.25 m2 (The max. usable press width depends on the widths of the individual lamellas.) Wood type Softwood/hardwood Press without options Electrical connection, press: 7 kW Electrical connection, 40 kW generator: 56 kW Operating voltage: approx. 400 Volt / 50 Hz (C/s) Collection table extended to 3700 x 1300 mm, with stainless steel wood support Motor-driven multi-function slider Lamination press Profipress L 2500 Press bed area approx. 2500 x 1300 mm Sturdy base frame with lower press table made of stainless steel as a grounding electrode Quick-change stop guide sets for panel thicknesses of 19 - 40 mm, which can be hydraulically adjusted to the current filling width Hydraulic special pressure elements ensure uniform pressure distribution over the entire joint length and compensate for tolerances In multi-lane operation, filling widths may vary by a maximum of 15 mm Upper pressure plate with hydraulic drive generates high vertical pressing pressure for minimal displacement Integrated hydraulic unit for generating pressing force and driving the hydraulic motors Control cabinet and control panel Protective cladding Additional individual pressure elements from above Automatic gluing station with precision gluing head Infeed for different widths Camera Washing and rinsing device for gluing head Modem incl. software for online connection Note: The technical data and descriptions are copies of the order confirmation from that time. The information is provided for informational purposes only and is non-binding. Isdpjzuzwqofx Abnoba

Condition: used, Year of construction: 2019, Corpus press Manufacturer: LINYI JIANZHONG WOOD MACHINERY Type: JJZ-CP Year of manufacture: 2019 The JJZ-CP press is suitable for the production of plywood, doors, and MDF panel joints. The feeding and removal of the glued elements are carried out automatically via powered roller conveyors. Technical data - Max. pressure 500 t (adjustable) - Max. filling height 1300 mm - Min. filling height 900 mm - Max. filling size 1300 x 2500 mm - Press dimensions 3600 x 1370 x 4500 mm - Press placement approx. 500 mm below floor level - Feeding table 2000 x 1960 mm - Receiving table 2350 x 2500 mm - Max. power 13.2 kW Isdezuzwkspfx Abnoba - Weight 12000 kg - CE marking - Capacity: 6 batches per hour 2 corpus presses are available for sale. Note: The technical data and descriptions are transcriptions from the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 1998, Continuous body press Manufacturer: LIGMATECH TYPE: MPP 15 Year of manufacture: 1998 The MPP 15 is a flexible press for batch-related production without setup times. The MPP 15 can be used individually or in various combinations in an assembly line. The pressing forces are applied pneumatically. The separately adjustable vertical and horizontal pressure allows for pressing both horizontal and vertical bodies. The vertical forces are transmitted through a plate, while the horizontal forces act on the body via press cheeks. The position of the center press cheeks can be adjusted using adjustable stops, allowing for different heights of bottoms and sides. During the infeed process, the body is measured photoelectrically, which automatically positions the horizontal pressure bar. Technical data: Body dimensions: Length: min. 300 mm / max. 2300 mm Height: min. 300 mm / max. 1220 mm Depth: max. 600/800/1000 mm (depending on the press type) Pressing pressure: vertical max. 17 kN horizontal max. 16 kN Isdpfx Aszuzv Tsbnsba Working height: 500 mm Transport speed: min. 8 m/min. / max. 37 m/min. Pressing time: selectable up to 999 s Operating voltage: 400 V, 50 Hz Control voltage: 24 V DC (according to VDE) Required air pressure: 5...8 bar Air consumption: 120 NL/cycle Total connected load: 3 kW Weight: approx. 4 tons Required room height: 3000 mm Extended infeed belt as a staging area Note: The technical data and descriptions are a transcript of the original order confirmation. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2000, Corrugated board press Manufacturer: Hüttenhölscher Year of manufacture: 2000 Technical data Voltage: 400 V Current: 32 A Ibsdpozuzvmjfx Abnsa Frequency: 50 Hz Compressed air: 6 bar Note: The technical data and descriptions are a transcript of the order confirmation from that time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2001, Thermo-lamination system Manufacturer: BÜRKLE Type: FFAII 1300 Year of manufacture: 2001 Technical data: Working width: 1300 mm Panel dimensions Width: 200 - 1300 mm Length: 400 - 3000 mm Thickness: 8 - 40 +/- 0.2 mm Film dimensions Width max. 1320 mm (lateral overhang up to 20 mm) Roll diameter 76 or 152 mm (3" or 6") Working height above floor: 940 mm Ibsdpfezuzt Sex Abnja System speed: 15 - 45 m/min Three-phase drive with vector control Operating side: right Panel feed: centered System configuration FFAII 1300 - Brush machine DBM (chain brushes) - Preheating and smoothing calender GKL, D = 500 mm - Thermo-oiler heater 36 kW - Hardener application machine DAH + complete hardener circulation system with monitoring - Transport section + IR zones with temperature sensors - Adhesive application machine DAK + automatic level sensing - Cooling unit for DOW cooling - Adhesive supply - Conical transport section TKE - Lamination calender EKM, D = 500 mm + film unwinding station + separating station + belt transport section with operator platform for FVE - Expansion shafts - Smoothing calender GKL, D = 500 mm at the inlet of the conveyor belt - Thermo-oiler heater 96 kW for lamination calender and smoothing calender - Central control cabinet - I.S.E. Optimat ISL 111 (year of manufacture 2004) Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Condition: used, Year of construction: 2016, Laminate Coating System Manufacturer: Type: Master PUR-1400 Year of manufacture: 2016 Technical data Professional PUR hot-melt laminating system for acrylic, PET, PVC, HPL, and CPL sheets General description The MASTER PUR-1400 is a professional, high-performance laminating system designed for single-sided lamination of sheets with PUR hot-melt adhesive. The system is suitable for continuous industrial production and offers excellent surface quality with low adhesive consumption. It is designed for the production of high-quality furniture panels, interior design components, wall panels, and decorative panels. Suitable substrates The machine is suitable for laminating: MDF Chipboard Plywood PVC sheets Gypsum boards Other wood-based panels Compatible surface materials The system is designed for processing the following materials: Acrylic sheets (high gloss & super matte) PET film PVC film HPL laminate CPL laminate Decorative paper Technical data Working width: 1,400 mm Maximum sheet size: 2,800 x 1,300 mm Sheet thickness: 2-40 mm Production speed: 5-17 m/min Throughput: 3-5 sheets/min Maximum productivity: up to approx. 1,200 sheets per 8-hour shift Ibjdjzuzkqjpfx Abnsa Installed motor power: 21.49 kW Heating power: 51.7 kW Overall dimensions of the machine: approx. 16 x 2.5 x 2 m Required installation area: at least 6 x 22 m System configuration The production line includes: Automatic feeding system with roller conveyor Brush cleaning system for sheets Infrared preheating oven (IR) 3-roller PUR adhesive application system Feeding station for decorative material Laminating press with pressure rollers Take-away conveyor 208-liter melting tank for PUR hot-melt adhesive Advantages Excellent laminating quality Uniform PUR adhesive application Suitable for high-gloss and super-matte acrylic surfaces Low adhesive consumption Stable and reliable operation in industrial series production High production efficiency Easy operation and maintenance Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.