Used paint finishing systems for sale (94)

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. Kdedpfewzl Hxsx Ahbju • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: good (used), Airless sprayer, painting device, spray pack, paint sprayer, paint spray system, paint pump, electrostatic sprayer, airless complete system, pneumatic piston pumps, airless high-pressure pump, air motor, AIR MOTOR Kdodpew U T Atsfx Ahbou -Manufacturer: Wagner, Airless sprayer type: 33-70 with transport trolley and spray gun -Material flow: max. 12.6 l/min -Air inlet pressure: max. 8 bar, operating pressure max. 264 bar -Individual components: see photos -Dimensions: 830/680/H1140 mm -Weight: 50 kg

Condition: new, Year of construction: 2025, total height: 4,000 mm, total length: 7,000 mm, total width: 3,000 mm, warranty duration: 24 months, temperature: 80 °C, air demand: 36,000 m³/h, input voltage: 380 V, heating capacity: 345 kW (469.07 HP), power: 40 kW (54.38 HP), fuel: liquid petroleum gas (LPG), energy consumption: 40 kWh, insulation material: Mineralwolle, insulation thickness: 50 mm, nominal power: 345 kW (469.07 HP), Equipment: lighting, MAIN STANDARD Our paint booths are designed to meet all necessary requirements for paint application, including air filtration, extraction, lighting, and a controlled environment. Booth processes are managed via a PLC system, ensuring that desired values are maintained consistently. OPERATING PRINCIPLES OF THE BOOTH The booth’s processes are managed through a control panel, which oversees the following steps: PAINTING PROCESS During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled through the extraction unit. Floor filters (paint stop filters) collect paint particles, and the air passes through final exhaust filters before being discharged. FLASH-OFF PROCESS After painting, the booth continues operating for approximately 15 minutes to purge residual solvents and thinners. During this phase, fresh air circulates from outside into the booth. DRYING PROCESS In this stage, 80% of the air passing through the booth is heated to 60°C and introduced via a distribution system. Since 20% of the solvent is released during drying, it is expelled with the exhaust air. Industrial coatings are typically dried at 60°C, but the booth temperature can be adjusted as needed via the control panel. COOLING PROCESS After the 30-minute drying cycle, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the subsequent 5-minute cooling phase, fresh air from outside circulates through the booth, after which the system shuts down automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT These control panels govern the functions and operation of machines and devices housed within the booth. The panel is made of durable galvanized sheet and steel profiles and is fully enclosed to protect against dust and moisture. Electrical Equipment and Control Panel: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. Kdedpewzmcbefx Ahbsu • Heat-resistant cables are used for command and control connections between the control panel and motors or other electrical devices. • Electrical wiring is designed to accommodate booth relocation if needed. • Operating equipment uses 380 V 50 Hz, while control devices operate at 220 V. • The booth’s operation time can be monitored on the electronic control panel, enabling straightforward maintenance scheduling. • Temperature and time settings for booth ventilation (solvent flash-off), intermediate drying, and final drying can be easily adjusted to required values on the digital display of the electronic control panel. • Users can monitor and adjust the drying time using the heating thermostat and time relay.

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 3,500 mm, total length: 7,050 mm, total width: 4,100 mm, volume flow: 36,000 m³/h, temperature: 80 °C, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), Equipment: cabin, lighting, Paint and Drying Booth It is the centerpiece of your entire painting operation: the combined paint and drying booth. (Alternatively available as a separate paint booth with a dedicated dryer.) Our solutions feature full-surface ceiling filters and, optionally, full-surface floor extraction with drive-over grating or wall extraction at the position of your choice. Kjdsxa H Ewspfx Ahbodu If you wish to further increase the efficiency of the system beyond heat recovery and infinitely variable control via frequency converter, we can also offer you a sectional control system. This enables you, for example when doing spot repairs or partial booth loading (such as painting only add-on parts), to activate only the section where the parts are located. This allows you to operate with a reduced air volume, save energy, and minimize costs, all without compromising quality. Feel free to contact us – we would be happy to demonstrate these options in detail. Do you have any questions or suggestions? We are happy to assist you.

Condition: new, functionality: fully functional, machine/vehicle number: G30C25, overall weight: 33 kg, operating pressure: 207 bar, compressed air connection: 7 bar, Air-assisted 30:1 Merkur complete system: - Incl. Airmix spray gun PerformAA 50 - Chassis mounting - Incl. spray gun air-material hose, material filter - Permissible material operating pressure: 207 bar - Max. air inlet pressure: 7 bar - Max. material flow rate: 1.5 l/min. Graco spray guns in our clearance sale: We need space and are therefore offering this and other selected Graco Merkur pumps at particularly attractive clearance prices. If you are interested, we will be happy to assist you. Sales notes: Sales exclusively to business customers. No sales to private customers. Sales and delivery exclusively within the EU – no sales to third countries. Delivery conditions and shipping costs based on individual effort and agreement. The sale is made with the exclusion of any warranty. Are you looking for other machines or similar products? Kedpfezv S T Esx Ahbsdu Please do not hesitate to contact us. At Oltrogge, we regularly have a wide range of new and used machines as well as other products from our technical product range available. We will gladly check if we can offer you a suitable alternative.

Condition: used, Year of construction: 2015, machine/vehicle number: 315031/02, working width: 1,800 mm, workpiece length (max.): 3,000 mm, workpiece height (max.): 25 mm, TECHNICAL DETAILS Workpiece dimensions Maximum length: 3,000 mm Minimum length: 400 mm Maximum width: 1,800 mm Minimum width: 200 mm Maximum thickness: 25 mm Minimum thickness: 3 mm Maximum deflection: 1 mm Maximum paper roll diameter: 500 mm Paper web width: 1,980 mm Maximum working width: 1,800 mm MACHINE DETAILS Minimum temperature: -5 °C Operating speed: 0.8–2 m/min Voltage: 400 V Frequency: 50 Hz Pressure: max. 6 bar Ksdpfxjzypm De Ahbsdu EQUIPMENT Roller conveyor TVR18/2000 Working width: 1,800 mm Speed: 0.35–6.1 m/min Roller diameter: 66 mm Roller spacing: 125 mm

Condition: new, functionality: fully functional, machine/vehicle number: G36W05, overall weight: 39 kg, operating pressure: 248 bar, compressed air connection: 7 bar, 36:1-Mercury Pump: - Wall-mounted - Includes suction hose, material filter - Permissible material operating pressure: 248 bar Kdjdpfjzwb Nrex Ahbju - Max. material flow rate: 6 l/min. Graco spray guns in our clearance sale: We need space and are therefore offering this and other selected Graco Mercury pumps at particularly attractive clearance prices. If you are interested, we will be happy to assist you. Notes on the sale: Sale exclusively to business customers. No sale to private customers. Sale and delivery exclusively within the EU – no sale to third countries. Delivery conditions and shipping costs will be determined individually based on effort and agreement. The sale is made with the exclusion of any warranty. Are you looking for other machines or similar products? Please feel free to contact us. At Oltrogge, we regularly have a wide range of new and used machines as well as other products from our technical range available. We will be happy to check if we can offer you a suitable alternative.

Condition: new, functionality: fully functional, machine/vehicle number: G30W55, overall weight: 34 kg, operating pressure: 207 bar, compressed air connection: 7 bar, 30:1 Merkur pump: - Wall-mounted - Includes suction hose and material filter - Permissible material operating pressure: 207 bar - Max. material flow rate: 4.5 l/min. Ksdpfxszwb Hwo Ahbsdu Graco spray guns in our clearance sale: We need space and are therefore offering this and other selected Graco Merkur pumps at particularly attractive clearance prices. If you are interested, we will be happy to assist you. Notes on the sale: Sale exclusively to business customers. No sale to private customers. Sale and delivery exclusively within the EU – no sale to non-EU countries. Delivery terms and shipping costs will be determined individually based on effort and agreement. The sale is made without any warranty.

Condition: new, Year of construction: 2021, functionality: fully functional, machine/vehicle number: M166011 01 G21C, The LineLazer V 250SPS model with paint guns is a self-propelled solvent painting machine with reflective beads designed for large and heavy striping jobs, including painting parking lots and roadways. Pressurised bead system:  Excellent bead application performance  Ensures proper flow of beads Automatic paint gun system  Quality solenoid driven system Remote control control box  Easy to use and highly visible in all conditions 25 gallon paint tank  Less refills  Extended stripping time with high capacity hopper Honda® GX engine  Reliable and easy to start Kjdpfx Ajt Dlmbohbodu  Oil alarm stops engine to prevent damage if oil level drops too low Electric start  Quick start EasyMark gun adjustment system  Easy gun adjustments  Easy gun adjustment every time  2 gun capability with QuikSelect gun selector Use of front or rear holster Self-centering front wheel  Simple operation  Foam-filled, three-wheel design for stability Additional features  Easy steering adjustment  Durable Chromex pump  High efficiency hydraulic motor  High capacity cooling system  Easy Out pump filter

Condition: new, Year of construction: 2027, POWDER COATING SYSTEM FOR CAR WHEELS AND RIMS Oven contains 4 pieces of 22’ wheel rims in 1 batch COMPONENTS OF THE PLANT: * 1.5x1x1.3m POLYMERIZATION OVEN, 18KW ELECTRICAL * VFK-2 ONE-SIDED POWDER COATING CABINET * OVERHEAD CONVEYOR AND LOAD TROLLEYS Kodpfx Ahsvv Rfdebjdu Delivery: 6-8 weeks EXW Istanbul factory Assembly and training included We offer the best technical solutions and competitive prices Contact us for more information and quotations

Condition: new, Year of construction: 2027, TALC POWDERING MACHINE FOR ELECTRICAL CABLES Kjdpfovxfg Isx Ahbsdu EXTERNAL DIMENSIONS Powdering unit : L450 W450 H1500mm Filtration unit : L750 W750 H1825mm Both units are connected to each other with Ø80mm air hose and clamp system CABLE PASSAGE Size : 100 mm diameter Height from ground : Manually adjustable, from 1.000 mm to 1100mm Cable insulation material : PVC, PE, XLPE to be used Cable size to be powdered: 5–70 mm diameter HIGH VOLTAGE UNIT Input voltage : 14V 16kHZ Output voltage : 100 kV Max. current : 120 µa Polarization : Negative TECHNICAL SPECIFICATIONS OF THE MACHINE Input : 220V 50 Hz Installed power : 1 KW Extraction fan : 3.000 m³/h 0,75KW Vibration : 0,15KW 220V Compressed air : 6-10 bar Air consumption : 300 lt/min Filtration : 320x300mm polyester filter Filter cleaning : Automatic Powder recycling : Vibration sieve Powdering method : Application by 2 electrodes, electro static application • Cable passage height from the ground adjustable, according to your extrusion line • Coating and filtration unit can be combined or separately

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 7,000 mm, total width: 4,000 mm, total height: 3,130 mm, inner dimension height: 2,700 mm, inner dimension length: 6,900 mm, inner dimension width: 3,900 mm, Equipment: cabin, The automotive spray booth is a fundamental device in paint repair technology, enabling painting work to be carried out in safe and comfortable conditions while minimizing the negative impact on the surroundings and the environment. Specifications: - External dimensions: 7000 × 4000 × 3130 mm - Internal dimensions: 6900 × 3900 × 2700 mm - Entrance door: 3000 × 2600 mm (three-wing design) - Service door: 640 × 1800 mm - Structure: standard steel - Heat exchanger: standard steel - Panels: EPS polystyrene - Total power: 7 kW - Installation: indoor only Cabin Wall Structure: - Thickness: 50 mm - Insulation: EPS polystyrene - Color: white Cabin Base: - Cabin mounted directly on floor/concrete surface - Installation possible only indoors Double Roof: - Upper external layer: corrugated steel panels - Inner structure: partially grated Air Circulation System (Supply System): - Jet turbine 5.5 kW – 1 unit - Airflow capacity: 20,000 m³/h - Belt-driven system - Air recirculation control: none Lighting (Side Lights): - 20 side-mounted lamps - No option for ceiling lighting Air Heating System: - Single-stage Riello G10 oil burner, 54–120 kW - Manual burner control - Heating time: approx. 20 minutes Cabin Access: - Main Doors: - Dimensions: 3200 × 2600 mm - Three-leaf door system - Service Door: - Equipped with a separate service door - Pressure locks installed Filtration System: - Air intake: Pre-filter - Ceiling filter: Main high-flow filtration Filter Specifications: - Weight: 600 g/m³ - Thickness: 50 mm - Airflow: 900 m³/h - Capture efficiency: 97% - Air velocity: 0.25 m/s - Dust holding capacity: 650 g/m³ - Max temperature: 100°C Kdjdpfoxnbf Uex Ahbju - Filtration class (EN 779): M5 - Fire resistance (DIN 53438): F1

Condition: new, total height: 31 mm, total length: 46 mm, total width: 37 mm, overall weight: 23 kg, HIGH-PRESSURE PAINT HEATER, ATEX COMPLIANT, VISCOUNT 2 - Brand: GRACO - REF. 245863 - 123 - Viscount 2 Graco, 220 V, 276 bar, 250°C, EEX compliant. - Suitable for general industry, metal, and wood applications. Kedjzy U Slepfx Ahbodu - NEW, UNUSED PRODUCT - VAT not included.

Condition: new, Year of construction: 2026, The illustrative photos show the realizations for the customer of the 4x7 cabin The offer applies only to the painting booth without the preparation area (possibility to purchase a preparation zone at the customer's request) - External dimensions: 7000x4000x3500 mm - Internal dimensions: 6900x3900x2650 mm - Entrance gate: 3000x2600 mm (three wings) - Service door: 640x1800 mm - Construction: high-grade steel - Heat exchanger: high-grade steel - Panels: filled with mineral wool - Total power: 16 kW - Floor fully grated - Air supply system: Jet turbine 4.0kW - 2 pieces - Exhaust system: Stream turbine 5.5kW - 1 piece - Ceiling lights: Coffers with LED fluorescent lamps 32pcs. - Side lights: LED panel 120x30cm - 8 pcs. Power: 48W - one piece 1000 lumens - Burner Riello 40 G20 95-213 KW - The cabin is available in different colors Kdsdpfxor Ha Ehe Ahbsu

Condition: new, Year of construction: 2027, DESIGN VFDK powder booths are designed as an open wall cartridge filtered for manual powder coating use from one side. Powder booths are manufactured of externally powder coated sheet metal structure with castor wheels at the ground. The system consists of filtration system with automatic cleaning, ventilation and electrical control panel. Long lasting 100% polyester cartridge filters are used for high efficiency. WORKING PRINCIPLE Air flow generated by the extraction fan carries overspray powder coating particles to the filter unit and collects them at the outer surface of the filters. Filters are cleaned by pulse valve operated pull-reverse system during the operation. Powder coatings accumulated by this way at the ground of powder booth are collected manually in the drawer and can be reused after sieving. A hopper with vibrated sieve can be added optionally for powder recycling. Kodpfsvv H Hdex Ahbjdu ADVANTAGES Saves space in the workshop Easy and fast cleaning Made in Türkiye CE Mark We offer the best technical solutions and competitive prices Contact us for more information and quotations

Condition: new, Equipment: cabin, Stationary small parts spray booth Dixi █████ Achieve perfect and uniform coating of small parts. The extraction system ensures optimal results even in the smallest spaces. Optionally equipped with a turntable or a wheel holder, as well as a compact yet powerful extraction unit, it is perfectly suited for processing small workpieces and wheels. The side panels effectively limit the distribution of overspray, allowing work to be carried out in confined spaces without contaminating surrounding areas. Integrated lighting is also available as an option. Additionally, thanks to its low weight and minimal connections, the booth can be relocated to a new site in no time, ensuring your flexibility at all times. The system comes fully pre-assembled and ready for immediate use. Your Benefits Thanks to its compact design, flexible dimensions, and versatile accessories, this booth offers a broad range of applications. The sophisticated modular system requires minimal space and is therefore suitable for use in virtually any premises. Different filter media and stages enable highly efficient operation, while filter changes can be performed in just a few minutes. Application and Safety Processing of both water-based and solvent-based coating materials is enabled by the use of ATEX-certified explosion-proof motors. Kdedpfoxa Hx Rjx Ahbeu It can also optionally be used for spraying adhesives. The large filter surface ensures uniform extraction throughout the process.

Condition: new, Year of construction: 2026, functionality: fully functional, total length: 5,000 mm, total width: 3,500 mm, total height: 2,950 mm, inner dimension height: 2,650 mm, inner dimension length: 4,900 mm, inner dimension width: 3,400 mm, Equipment: cabin, Automotive Spray Booth Kdedpfx Aexnpczehbju The automotive spray booth is a fundamental device in paint repair technology. It enables painting operations to be carried out in safe and comfortable conditions while minimizing the negative impact on the surrounding environment and the workspace. Specifications: - External dimensions: 5000 (+ air handling unit 1350 × 2900 mm) × 3500 × 2950 mm - Entrance door: 3000 × 2600 mm (three-wing design) - Service door: 700 × 2000 mm - Structure: made of steel sheets - Heat exchanger: standard steel - Panels: steel panels with mineral wool insulation in the walls Cabin Wall Structure: - Thickness: 50 mm - Insulation: EPS polystyrene - Color: white Cabin Base: - Cabin mounted directly on floor/concrete surface Double Ceiling: - External ceiling paneling - Full-surface plenum chamber for air supply Air Exchange System: - Supply system: - Jet turbine 4 kW – 2 units - Airflow capacity: 26,000 m³/h - Airflow system: - Jet turbine 5.5 kW – 1 unit - Airflow capacity: 18,000 m³/h Lighting: - 8 side-mounted lamps - Ceiling lighting: 24 LED tubes Air Heating System: - Single-stage oil burner Riello model 40 G20 - Burner control: manual - Heating time: 8–15 minutes Filtration System: - Double-layer filtration structure - High-capacity air purification system with filtration efficiency up to 99%

Condition: new, Year of construction: 2027, functionality: fully functional, TRANSFER TYPE POWDER COATING LINES The transfer type conveyor consists of a combination of conveyor rails. The effective powder coating system layout is designed by our project department according to your workshop dimensions based on the products to be coated and daily quantities. Workpieces are loaded onto the bars which are moved manually or automatically to bring the products to the needed, booth or oven. The advantage of this system is that the products are loaded on the conveyor and do not tire the operator as they move on the conveyor until the end of the process, so it is an efficient system. The movement of the bars can be automated at any point in the system, making the entire conveyor line a cost-effective alternative to power&free conveyors. Kdodpfxovv H Uue Ahbju In the painting system, automatic coating can be achieved by adding a conveyor system above the powder or paint booth and adding a reciprocator and automatic gun to the coating booth. We offer the best technical solutions and competitive prices * Office in France and Germany, Contact us for more information and quotations

Condition: good (used), A series of machines for a complete UV coating line. Kedpfx Aheg T U Unobodu

Condition: new, Year of construction: 2026, functionality: fully functional, total height: 5,850 mm, total length: 12,125 mm, total width: 5,150 mm, overall weight: 8,000 kg, warranty duration: 12 months, inner dimension height: 5,000 mm, inner dimension length: 12,000 mm, inner dimension width: 5,000 mm, Equipment: cabin, lighting, PAINT BOOTH 12x5x5M EZ Series Model: - LED ceiling lighting - LED side lighting - RIELLO oil burner - Four fans, including: ‎ ㅤ- 2x supply fans ‎ ㅤ- 2x exhaust fans TECHNICAL PARAMETERS: - External dimensions: 12125x5150x5850 mm - Internal dimensions: 12000x5000x5000 mm - Entrance doors: 4000x4800 mm (2 units, four leaves, reinforced hinges) - An additional BOX 1650 mm x 8000 mm should be included in dimensions – can be placed on either the right or left side. - Structure: galvanized steel frame - Heat exchanger: high-grade stainless steel - Panels: filled with mineral wool insulation - Drive-on ramps – 2 units - Fully grated floor The reinforced frame construction prevents vibration and the air surge effect from the main supply duct. Double Roof Design: - Upper outer layer - Inner truss structure with V600 ceiling filter Air Circulation System: - Supply system: Jet turbine 7.5 kW – 2 units - Exhaust system: Jet turbine 7.5 kW – 2 units Air Filtration System: - Pre-filter collects particles larger than 10 μm - Ceiling filter collects particles larger than 5 μm - Floor filter: Paint Stop - Carbon filter Lighting: - Ceiling lights: 52 LED tubes (14 angled fixtures with 4 tubes each) - Side lighting: 26 LED panels integrated into the right, left, and rear walls Burner: Riello – 2 units, oil model 40 G20, approx. 200,000 Kcal/h - Heat exchanger: high-quality stainless steel - Heating time: 8–15 min (max. 80°C) Kjdpfx Aexm U Exohbsdu Optional Features: - Roof-mounted boxes - Insulated roof - Pass-through doors - Water curtain - Color according to RAL palette - Explosion-proof (EX) version available

Condition: new, Year of construction: 2026, - External dimensions: 8125x4650x4600 mm - Internal dimensions: 8000x4500x3800 mm - Entrance gate: 4000x3800 mm (four wings) - Service door: 640x1800 mm - Construction: high-grade steel - Heat exchanger: high-grade steel - Panels: filled with mineral wool - Total power: 22kW - Seating: inside/outside Kdedpfxenbdlbj Ahbou (after prior roofing of the cabin by the customer on his own) - Floor fully grated - Air supply system: Jet turbine 5.5kW - 2 pieces - Exhaust system: Jet turbine 7.5kW - 1 piece - Ceiling lights: Coffers with LED fluorescent lamps 36pcs. - Side lights: LED panel 120x30cm - 12 pcs. Power: 48W - one piece 1000 lumens - Burner Riello RG5S 160-310 kW - The cabin is available in different colors

Condition: new, Year of construction: 2026, - External dimensions: 7200x5200x3800 mm - Internal dimensions: 7100x5100x3100 mm - Entrance gate: 4000x3100 mm (four wings) - Service door: 640x1800 mm - Construction: high-grade steel - Heat exchanger: high-grade steel - Panels: filled with mineral wool - Total power: 21kW - Seating: inside/outside Kjdpfx Aem Tv I Ajhbsdu (after prior roofing of the cabin by the customer on his own) - Floor fully grated - Air supply system: Jet turbine 5.5kW - 2 pieces - Exhaust system: Jet turbine 7.5kW - 1 piece - Ceiling lights: Coffers with LED fluorescent lamps 32pcs. - Side lights: LED panel 120x30cm - 12 pcs. Power: 48W - one piece 1000 lumens - Burner Riello RG5S 160-310 kW - The cabin is available in different colors

Condition: good (used), Paint roller machine, roller coating machine, powder coating system -Drying and exhaust air: used for slat/blind production -Dimensions: 2950/800/H1920 mm Kdsdpfx Aogal Agehbju -Weight: 484 kg

Condition: new, Year of construction: 2027, VFK MANUAL POWDER COATING BOOTH WORKING PRINCIPLE The extraction fan is located at the top of the booth, at the end of the system. The pressurized air flow created by the fan carries the powder coating particles towards the filters and collects them on the outer surface of the filters. Powder coating filters are cartridge type and are cleaned during operation by a pull-reverse filter cleaning system. The pull-reverse system consists of pulse valves and a compressed air tank, controlled automatically or operated using manual buttons on the control panel. Kdjdpevv Rfkjfx Ahbou POWDER RECYCLING As a result of the filter cleaning system, powder coating particles fall down and are manually collected in a bucket at the bottom of the filter unit. This bucket can optionally be a simple drawer or can be with a sieve having a vibration motor with a powder pump to sift the powder coatings collected on it and transfer the sifted powders for reuse and send it to the powder recovery system for reuse. The powder coating booth is designed as single-sided open type for manual powder coating. There is an electrical panel on the system and the electrical wiring up to the motors has been done. Made in Türkiye CE Mark We offer the best technical solutions and competitive prices Contact us for more information and quotations

Condition: new, Year of construction: 2026, -External dimensions: 6058x2438x2591 mm -Internal dimensions: 5538x2170x2485 mm - Sea container: 20DV - Door: integrated into the cabin door - Windows: with metal protective mesh - Lighting: 2 LED panels -No assembly required - ready to go Steering - Automatic from the central block located outside; Power - 400V Kdedpfx Aonbd Ilshbju Supply: -Fan - 3 Kw - Flow velocity - 0.7 m/s -Air flow: 9500 m3/h -Recirculation - closed circuit Heating - heating supply 12kW Filters - preliminary, cardboard, carbon Security: -Emergency stop -Pressure lock on the door Equipment: -16A socket -Air preparation team - Pneumatic retractor