Used Centering for sale (12,553)

Year of construction: 1981, condition: used, Type: BMC 5B Manufacturer: Toshiba Year: 1981 Pallets: 2 pcs 500x500mm pallet changer Tools: 30 pieces in magazine BT50 Hsdpfx Afsbhn Nmeijnu Speed: 28 - 3150 1/min Travel: X=630mm y=500mm z=500mm table pitch: 1° table load: 800kg General: Machine is in a good condition technically o.k. optically i.O.

Year of construction: 1985, condition: used, Drilling capacity in ST 60 20mm Hsdpfjb Hf I Tsx Afienu Tapping capacity M16 Milling capacity in ST 60 up to 20 cm³/min Milling capacity in AL up to 80 cm³/min. Tool holder SK30 Spindle motor - direct current 5.7 kW Speed range/max. torque i 1:1 20 to 6000 rpm with 40 NM Step change 1.12 Spindle bearing diameter 50mm Tool clamping mechanical Pull-in force 3000 N feed of the Z-axis 200mm rapid traverse speed of the Z-axis 15m/min feed force of the Z-axis 6000 N feed path of the X- and Y-axis 500 x 250mm clamping surface 630 x 400 mm rapid traverse rate of the X- and Y- axis 15 m / min feed force of the X- and Y- axis 6000 N Programmable feed rate in all three axes 1 to 4000 mm/min Projection spindle to guide 300 mm Distance spindle support to table surface 190 to 390 mm (stroke 200mm) and 190 to 615 mm (stroke 400mm) Number of magazine positions (tools) 12 Tool shank steep taper shank 30 max. tool diameter at full occupancy 63mm max. tool diameter with free secondary places 100mm max. permissible tool weight 5 kg tool change time approx. 1 sec. Cut to cut time approx. 3.2 sec. Total connected load approx. 15 kW (but only needs approx. 5~10 kW in operation) Machine weight approx. 3,5 to. Requires commercial compressed air connection

Year of construction: 1985, condition: used, Technical manuals and tool holders available; further technical data: Drilling capacity in ST 60 20mm Threading capacity M16 milling capacity in ST 60 up to 20 cm³/min Milling capacity in AL up to 80 cm³/min. Tool holder SK30 Spindle motor - direct current 5,7 kW Speed range/max. torque i 1:1 20 to 6000 rpm with 40 NM step jump 1,12 spindle bearing diameter 50mm Tool clamping mechanical Pull-in force 3000 N feed of the Z-axis 200mm rapid traverse speed of the Z-axis 15m/min feed force of the Z-axis 6000 N feed path of the X- and Y-axis 500 x 250mm clamping surface 630 x 400 mm Hnodpfx Afobwn Rhjisu rapid traverse rate of the X- and Y-axis 15 m / min Feed force of the X- and Y- axis 6000 N Programmable feed in all three axes 1 to 4000 mm/min Spindle overhang to guide 300 mm Distance between spindle and table surface 190 to 390 mm (stroke 200mm) and 190 to 615 mm (stroke 400mm) Number of magazine positions (tools) 12 Tool shank steep taper shank 30 max. tool diameter with full occupancy 63mm max. tool diameter with free secondary places 100mm max. permissible tool weight 5 kg tool change time approx. 1 sec. cut to cut time approx. 3,2 sec. total connected load approx. 15 kW (but needs only approx. 5~10 kW in operation) Machine weight approx. 3,5 to. needs commercial compressed air connection distance measuring systems = glass measuring scales spindle conveyor with ejection height 850 mm; make: KNOLL type: 240 S-1/150; incl. documents Shifting table for

Year of construction: 1992, condition: used, Dear Sir or Madam ! Below we offer without engagement: Make : Steinel Designation : H. - Machining Center Type : BZ 20 Year of manufacture : 1995 Technical data : travels 400 x 300 x 320 mm tool changer 60 times Control Siemens 880 M mounting SK 40 (Further data also on request) Please let us know if you are still interested in purchasing such a machine. If you are looking for other objects, or if you intend to sell yourself, we also ask for your non-binding information. If you are interested, we would like to hear from you. With kind regards, gez. Andree Hnjdpfx Aobcbf Tjfisu

Year of construction: 1978, condition: good (used), Ravensburger, type KT 45, year 1978 Center height over bed 600 mm Center distance face plate to support 450 mm Face plate diameter 1,000 mm turning diameter in the recess max. 1.350 mm with digital display Hnodpfx Afskyukdeiju Power 18,5 kW

Condition: good (used), Technical data: - Center height 220 mm - Turning diameter over bed 440 mm - Center height over bridge 330 mm - Turning diameter in the offset 630 mm - Center height / turning diameter over support 135 / 270 mm - Center distance 1000 mm - Spindle bore 52 mm - Taper of the tailstock quill MK 4 - Travel of the tailstock quill 310 mm Hnsdpfoqff D Iex Afieu - 18 spindle speeds 25 - 2000 rpm - feeds longitudinal + plane - metric thread / Withworth thread / modular thread / DP thread - Drive 400 V / 6 kW - 4-jaw chuck with interchangeable jaws and center point, new Multifix size B with 3 inserts

Condition: good (used), Year of construction: 1998, CNC MACHINING CENTER ALZMETALL BAZ 15, Year of manufacture: 1998 Technical specifications: Hnedpfov Rnyzjx Afisu X: 600 mm Y: 400 mm Z: 600 mm Table: 750 x 450 mm Main spindle: 10,000 RPM Control: Siemens Sinumerik

Condition: good (used), Used V. Machining Center, Homa, Type Ecocenter V350 Hnsdpfx Afewaakceisu X-travel 450 mm Y-travel 350 mm Z-travel 350 mm Table size 650 x 350 mm Speed 6000 rpm Fanuc 0M control system

Condition: good (used), Turning diameter over bed (mm) 365 Hsdpov U Uvwefx Afienu Turning length (mm) 1000 Spindle bore (mm) 42.5 Max. turning diameter over slide (mm) 205 RPM / speed 38 - 1600 (16x) Accessories: Digital readout, 2 axes 3rd spindle chuck 250 mm, 4th spindle chuck 200 mm, documentation, and Multifix tool holder

Condition: good (used), Year of construction: 2003, Hurco VMX 24, year of manufacture 2003 Travel X/Y/Z: 610 mm/508 mm/610 mm Rapid traverse X/Y/Z: 35 m/35 m/30 m Feed rate: 7,600 mm/min Table dimensions X/Y: 760 mm/510 mm Hnedpswya Unsfx Afiou Max. table load: 700 kg Tool holder: SK40 Tool positions: 24 Spindle speed: 10,000 rpm Power: 7.5 kW Dimensions approx.: 2,200 mm/2,400 mm/2,500 mm Weight approx.: 5,000 kg Control: Ultimax 4 (Documentation available)

Condition: used, Year of construction: 2008, Argo A51, year of manufacture 2008 Hedpfx Asxbz Uijfisnu Travel paths: X 510 mm, Y 350 mm, Z 300 mm Table: approx. 600 × 300 mm Control: FANUC Dimensions: 2,610 × 1,720 × 2,460 mm. Weight: approx. 2,700 kg.

Condition: good (used), Centre height: 175 mm Distance between centres: 800 mm Swing diameter over bed: 350 mm Swing diameter over cross-slide: 310 mm Spindle bore: 46 mm Speed range: 25 - 2000 rpm With digital readout Hnsdpjxc Ewwjfx Afiou

Year of construction: 1999, condition: excellent (used), DMU80E with hard disk storage Control Heidenhain 426M Hnedsgwt U Dopfx Afiou Year 1999 2014 axes and spindle revised Speed 18000 Since the revision approx. 1200 hours run Accuracy according to a new machine Chip conveyor available Accessories would be available at extra cost.

Condition: excellent (used), functionality: fully functional, Make: Colchester Type / Model: Student Tip width: 500 mm aperture: 42 mm Center height: 175 mm Turning diameter over bed: 350 mm over slide: 200 mm Speed range: 34 to 1,500 mm Longitudinal feed: flat: 0.04 to 0.25 mm/rev Connection: 1.1 / 2.2 kW Hodpfx Aou T Iwysfienu Accessories: steel holder, 3-jaw chuck, 4-jaw chuck, steel holder Weight: approx. 800 kg Dimensions: 1,550 x 900 x 1,200 mm

Condition: excellent (used), Mechanical/mechanical clamping system with force transmission, manually operated: Clamping system mechanical/hydraulic - Deformation-resistant design for very high clamping accuracy - For use on machining centers with high quality and production output - Drive spindle with clamping force presetting - Lubrication nipples on both sides for lubricating all guides and the spindle thread subject to wear - M12 fastening thread for workpiece stop guides subject to wear and the spindle thread - M12 mounting thread for workpiece stop - sturdy chip guard prevents chips from entering the interior of the body - all guides hardened and ground - height dimension base body/workpiece support -0.02 - important for paired use - supplied with reversible stepped jaws, hardened and ground. Further technical features: - Design: Model RKE - 3-sided clamping option - can be clamped horizontally, vertically or laterally - base body made of steel - hardened and ground - with power transmission RÖHM brand Jaw width 125 mm Material steel Jaw height 40 mm Model RKE Hsdpsqff Syjfx Afijnu Clamping force approx. 40 kN Clamping width 0 - 216 mm / 97 - 312 mm Total length 463 mm

Condition: good (used), Heckert CWK 400 Year of construction 1995 Control Siemens 840 Travel X/Y/Z 650/650/680 mm Spindle speed up to 10,000 rpm HSK 40 Hnsdpfx Ajru H T Iefiju Tool changer Rotary table 400 x 500 mm, chip conveyor Weight 12.5 tons.

Condition: good (used), Year of construction: 2004, OKUMA Euro Center V50, year of construction 2004 Control unit: OSP-10M Hnedpouh Skaofx Afiou Travels: X-1020 Y-510 Z-525 Table load 680kg Clamping surface 1200x510 Tool changer 20 times

Condition: good (used), Year of construction: 1967, Technical data: Centre height: 140 mm Turning length: 500 mm Accessories (included): Steady rest Multifix 'A' Collets 0.5 – 24 mm Milling attachment (Y axis) 3-jaw chuck 125 mm Faceplate 260 mm Live centre Drill chuck Die holder 4-jaw chuck Coolant pump Operating manual (German) Hsdsxlr Hkopfx Afijnu

Condition: good (used), various quills / center punches in sizes MK3 - MK6 (different manufacturers) Hnedpsipibxefx Afiou rotating and fixed quills

Condition: used, Year of construction: 1995, Fanuc ROBODRILL ALFA T10 B, year of construction 1995 Hjdevfpqwepfx Afijnu Revolutions 8000 rpm Pick-up Sk 30 Fanuc 16 M control Tool changer 10-fold

Condition: used, Year of construction: 1990, branded milling machine, Maho 1000 S x-path: 1000 mm y-path: 600 mm z-travel: 800 mm Spindle holder ISO: 50 Control is the Philips 432 Hjdpfx Afotrnrpeijnu with pallet changer, functional condition, recently overhauled rotary table

Year of construction: 1984, condition: good (used), Güdel G100 CNC with new Siemens control system working range - max. circulation Ø:260 [mm] - max. machining Ø:120 [mm] - traversing of the longitudinal slide:200 [mm] - traverse of the facing slide:120 [mm] Main spindle - spindle nose:A4 DIN 55021 - spindle bore for collets:type F38 - Power chuck Ø:165 [mm] - Bar passage Ø:32 [mm] - Speed range:50 - 60 000 [rpm] Main drive - DC motor:7 [kW] Feed drives (DC motors) - feed speed:0,01 - 6 000 [mm/min] - rapid traverse rate:6 [m/min] Tool carrier - 8-sided flat table turret Tool carrier plate interchangeable:210 [mm] - tool clamping surface:110 [mm] - Selectable for 2, 4 or 8 positions indexing:0.8 [sec.] - Repeat accuracy or linear system:0,001 [mm] Main dimensions - length:1 700 [mm] - Width:1 100 [mm] Hnedpsf Tpcxsfx Afiju - Height:1 850 / 1 600 [mm] - Height spindle center above floor:1 120 [mm] - Weight:approx. 1 300 [kg]

Condition: good (used), Used V. BAZ, DMG, type DMU 70 (3 axes) X-axis travel: 710 mm Hjdpfowa Dansx Afienu Y-axis travel: 520 mm Z-axis travel: 520 mm

Condition: good (used), Year of construction: 2013, DMG, Type DMC 635 Ecoline, Year 2013 Travel: X 635 mm Hjdpfxjwa A Rls Afienu Y 510 mm Z 460 mm Spindle speed 0-10,000 rpm Controlled axes: 3 Spindle mount: SK 40. L x W x H 3,500 x 4,000 x 2,700 mm Machine weight: 4,500 kg

Condition: good (used), Year of construction: 1991, CNC lathe, Emag USC-2 Built in 1991 Hnjdpfx Afswbu A Aeiou Center distance: 1000 mm Turning diameter over bed: 600 mm Maximum spindle speed: 2800 rpm Power: 46 kW