Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, Functionality: fully functional, pressing force: 100 t, bale weight: 1,400 kg, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 36,000 kg, oil tank capacity: 1,300 l, nominal current: 238 A, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a Cgobvmjvf E Avek Ifst bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, Technical data for the bale loosening drum: Manufacturer not known Type of bale loosening drum Year of manufacture not known Dimensions of the drum 6000 x 3000 mm (l x d) Height of the welded-in helix 300 mm Dimensions of the drum frame 4900 x 3400 x 2200 mm (L x W x H) Drive power 2 x 4 kW Functional description: Cgsbvju Thx Remk Ifjt The bale loosening drum was fed with pressed paper bales from which the binding wire had previously been removed. The pressed and compact bale is broken up and loosened by the baffle plates welded into the drum parallel to the conveying direction. The helix, which is welded in with an incline to the conveying direction, transports the loosened material further to the drum outlet. Here it falls through a hopper onto a conveyor belt for further processing. Scope of delivery: Bale loosening drum Frame with drive and roller bearings for the bale loosening drum Comments: Documentation (operating instructions, CE declaration, electrical/hydrical circuit diagram) is not available and cannot be supplied. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 2011, Functionality: fully functional, power: 9.7 kW (13.19 HP), Technical data cardboard shredder: Manufacturer Presto GmbH & Co. KG Type PZA Cjbju Tha Ijvmk Ifjgt Year of construction 2011 (38.761 h), 2007 (52.386 h), 2007 (52.998 h) und 2007 (55.325 h) stand operating hours counter November 2021 Throughput volume 130 m³/hour Speed 37/9 rpm Motor power 7,5 / 2,2 kW Electrical connection 32 A Dimensions shredder inside 1,490 x 1,320 x 530 mm (L x W x H) Dimensions shredder outside without cover 2,308 x 1,320 x 685 mm (l x w x h) Machine weight 0,45 tons Use of the systems: The four PZA cardboard shredders were in use in a Dutch logistics centre until 15 December 2021 to pre-shred loose, erected cardboard boxes from the returns department and then press them into bales. The cartons were fed manually onto the infeed conveyor and transported directly to the cardboard shredder by a sliding belt conveyor and shredded. The pre-shredded cardboard boxes were then transported over hundreds of metres to the baler where they were pressed. Scope of delivery: 4 pieces Presto cardboard shredder (2-shaft shredder) type PZA Comments: The cardboard shredders were an elementary part of the disposal line and therefore good maintained to ensure high availability of the returns department. The machines are in good condition and ready for immediate use. The price is per piece exw. our warehouse in Siddeburen, the Netherlands. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Technical data single-deck ballistic separator for three separation fractions: Manufacturer Lubo Screening & Recycling Systems B.V. Type Elliptical 10EBB05 Year of construction 2015 Screening area 12.5 m², consisting of 6 screen paddles 400 x 5000 mm Weight 7,100 kg Cgobvmou Tg A Iek Ifjt Note on the separation process: The Lubo Elliptical is a state-of-the-art ballistic separator. It separates the material stream into three fractions, heavier 3D fractions such as tin cans or PET bottles, lighter 2D fractions and screened fines. This ensures high separation quality for various waste streams such as mixed waste, packaging, mixed paper, film and cans. Condition of the machine: The Elliptical 10EBB05 ballistic separator is still in use at a large recycling company separating mixed waste until the 18th calendar week, when it will be replaced by a larger machine with a higher throughput capacity. The machine is in a well-maintained condition and works perfectly. On request, various spare parts can be purchased for a separate, additional fee. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2015, Condition: reconditioned (used), Technical data Feed hopper with hydraulic moving floor and bag opener: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Csbsu R Rtbsvmk Ifogt Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was in use at a large recycling company, where waste in bags was tipped into the hopper with wheel loaders and the bags were opened via the bag opener and the waste was conveyed in doses for further processing. The system worked perfectly until it was dismantled and was replaced by a larger system with a higher throughput capacity. The machine is in good working condition. On request, various spare parts can be purchased for a separate, additional fee. The buyer would have to dismantle the elevation for removal, as the machine is otherwise too high. Comments: The machine is currently being overhauled in our workshop. The photos show the machine in the current overhaul phase, so the system has not yet been fully reassembled. Once the overhaul work has been completed, probably in February 2025, the machine will be tested in operation without the use of materials. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2010, operating hours: 56,748 h, Functionality: fully functional, overall weight: 5,400 kg, rotor width: 1,600 mm, power: 45 kW (61.18 HP), rotational speed (max.): 107 rpm, rotor flight circle: 380 mm, working width: 1,600 mm, blade width: 40 mm, Technical data shredder: Cgsbvmsu Thabsk Ifjt Manufacturer ZENO Zerkleinerungsmaschinenbau Norken GmbH Type ZTLL 1400 x 1600 Year of construction 2010 Operating hours 56,748 hours Inlet cross-section 1400 x 1600 mm Main drive power 45 kW Rated current 81 A Hydraulic slide gate drive 2.2 kW Rotor flight circle 380 mm Rotor speed approx. 107 rpm Number of cutting tools 52 knives, 40 x 40 mm, with tool holders Screen perforation 40 mm Weight approx. 5400 kg Scope of delivery: Only the shredder with control cabinet is for sale. The discharge conveyor belt and the air conveyor system are not included in the scope of delivery. Remark: The shredder was used for shredding nonwovens and needle felts etc. and is in good, immediately usable condition. The machine is being replaced by a larger shredder due to its low throughput capacity. The machine is currently still assembled and can be inspected under power. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2014, operating hours: 5,059 h, Functionality: fully functional, pressing force: 48 t, bale weight: 550 kg, filling opening width: 1,020 mm, filling opening length: 1,250 mm, total height: 2,800 mm, bale height: 750 mm, bale width: 1,100 mm, overall weight: 12,000 kg, transport height: 2,800 mm, oil tank capacity: 300 l, power: 30 kW (40.79 HP), net weight: 12,000 kg, volume flow: 332 m³/h, nominal current: 59 A, Technical information baler: Manufacturer HSM GmbH + Co. KG Typ VK 4812 Year of construction 2014 Hours of operation 5,059 hours, stand November 2024 Press power main press 48 tons Specific press capacity 58,2 N/cm² Feed channel 1,250 x 1,020 mm Theoretic cycle time 11.2 sec. Theoretic throughput rate 332 m³/hour Bale size 1,100 x 750 x 600 up to 1,200 mm Driving motor 30 kW Connected load 32 kW Rated current 59 A Tying system 4-fold horizontal, fully automatic Throughput rate at a bulk weight of 20 kg/cbm up to 6 tons/hour bulk weight of 50 kg/cbm up to 13 tons/hour Bale weight up to 550 kg, depends on material SPS controller Siemens SIMATIC S7-200 Operating panel Siemens HMI Touch Panel Filling quantity hydraulic oil tank 300 L Oil type HVI 46 Machine installation dimensions with bale chute 10,046 x 4,387 x 2,705 mm (l x w x h) Transport dimensions baler 8,500 x 2,500 x 2,750 mm (l x w x h) Machine weight press approx. 12 t Cgsbvmevtpq Hjk Ifjt Scope of delivery: Baler HSM VK 4812, without hydraulic oil, without conveyor system. Two wire reel boxes for 8 pieces 40 kg wire reels, without wire Bale chute Machine documentation in German Comments: The press is equipped with an oil cooler and potential-free contacts for external control. The control cabinet is operated from the left in the direction of pressing, the needle unit is located on the right-hand side and can be folded back for transport. The press is in good condition, is currently still in operation and is used in a distribution warehouse for film compaction. In the 14th calendar week, the baler will be dismantled and replaced with a new, larger machine and will then be available for loading. A truck with an effective internal height of 2,800 mm is required to transport the baler. The press is loaded without hydraulic oil. The conveyor technology shown in the photos is not for sale and is not included in the scope of delivery. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagrams) is available in German. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: good (used), Year of construction: 2010, operating hours: 3,641 h, Functionality: limited functionality, pressing force: 36 t, filling opening width: 1,100 mm, filling opening length: 1,080 mm, bale height: 750 mm, bale width: 1,100 mm, power: 15 kW (20.39 HP), net weight: 4,000 kg, volume flow: 90 m³/h, Technical data baler: Manufacturer Presto GmbH & Co. KG Typ CC 36 M Year of construction 2010 Hours of operation 3,641 h Press power main press 36 t Specific press capacity 467 N/cm² Feed channel 1.080 x 1100 mm (l x w) Cjbju Thh Esvmk Ifogt Cycle time 34 sec. Capacity per cycle time 0,85 m³ Theoretic throughput rate 90 m³/h Throughput rate under operating conditions with a material bulk density of 35 kg/m³ approx. 51 m³/hour Bale size 1100 x 750 mm (w x h), length variable Driving motor 15 kW Tying 4-fold vertical, semi-automatic, with polyester synthetic yarn Throughput rate at a bulk weight of 35 kg/cbm 1,8 to/h bulk weight of 60 kg/cbm 2,5 to/h bulk weight of 100 kg/cbm 3,1 to/h Transport dimensions only baler 4.200 x 1.640 x 2.200 mm Machine weight baler approx. 4 to Comments: The press was checked for function in our workshop, then stored and is therefore available at short notice. The machine documentation (operating ins3.641tructions, CE, electrical and hydraulic circuit diagram) is available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2015, operating hours: 19,173 h, Functionality: fully functional, pressing force: 150 t, filling opening width: 1,100 mm, filling opening length: 2,000 mm, bale height: 750 mm, bale width: 1,100 mm, overall weight: 35,800 kg, oil tank capacity: 4,300 l, Technical data baler: Manufacturer Europress Umwelttechnik GmbH, Germany Type EP5 150 V5 Year of construction 2015 Operating hours 19,173 hours Number of pressed bales 282,961 bales Number of press strokes from the press ram 1,895,112 press strokes Pressing force of main press 150 t Specific pressing force 181.8 N/cm² Dimensions of feed chute 1,000 x 2,000 mm (w x l) Bale dimensions 750 x 1,100 mm (h x w), length variable Drive power 2 x 55 kW + 15 kW + 2 x 0.75 kW Rated current 230 A Cgsbvmk Iju Thfdofet Cable cross-section supply 120 mm² Tying 5-fold vertical, fully automatic Hydraulic oil tank capacity 4,300 l PLC control Siemens S7 / ET200S Transport weight press 35,800 kg Special equipment: Base plates and side walls made of HARDOX steel Free tamper in front of the counter blade, with cleaning cycle Scope of delivery: 1 piece baler 1 piece control cabinet 1 set of oil collecting pans under the baler 1 piece maintenance platform on the baling channel 1 piece Feed hopper 1 piece Drop chute 10 pieces wire reel stands 2 pieces wire drawing stations with deflection rollers 1 set of machine documentation (operating instructions, electrical circuit diagram, hydraulic circuit diagram, CE confirmation) Remarks: The machine is still completely assembled and available at short notice. Dismantling and loading is the responsibility of the buyer. The documentation (operating instructions, electrical circuit diagram, hydraulic circuit diagram, CE confirmation declaration) is available in German. An inspection is possible by arrangement. We do not assume any liability for the technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, Functionality: fully functional, pressing force: 50 t, bale weight: 550 kg, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale height: 720 mm, bale width: 1,100 mm, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Cgjbvmksu Thhrs Ifjt Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partially overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 1996, Functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2024, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with whirlulator, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Cgjbvsu Th D Romk Ifot Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: used, Overview of the equipment of a used sorting plant, year of construction 2009, with a sorting capacity of 25,000 t/year For sale is a complete used sorting plant for deinking paper, which can also be used for other materials. The plant consists of the following components: 1 piece sorting cabin with an integrated office (control room), external dimensions 14,200 x 11,400 x 4,350 / 8,170 mm (l x w x h), with 3 sorting belts and 10 sorting places, air-conditioned (heated). 1 piece ventilation system for the sorting plant with 17,600 m³/hour, manufacturer VTS Ventus, type VS-120-R-H/S 1 piece infeed conveyor belt, right, no. 10, dimensions 7,360 x 1,200 mm, drive power 3 kW 1 piece infeed conveyor belt, centre, no. 11, dimensions 7,360 x 1,200 mm, drive power 3 kW 1 piece infeed conveyor, left, no. 12, dimensions 6,360 x 1,200 mm, drive power 3 kW 1 piece sorting belt, long, right, no. 15, dimensions 8,350 x 1,200 mm, drive power 2.2 kW 1 piece sorting belt, short, right, no. 17, dimensions 4,350 x 1,200 mm, drive power 1.5 kW 1 piece sorting belt, long, centre, no. 14, dimensions 8,350 x 1,200 mm, drive power 2.2 kW 1 piece sorting belt, short, center, no. 16, dimensions 4,350 x 1,200 mm, drive power 1.5 kW 1 piece sorting belt, left, no. 13, dimensions 5,360 x 1,200 mm, drive power 2.2 kW 1 piece reversing belt, below sorting belts 14 and 15, no. 18, dimensions 5,200 x 1,000 mm, drive power 2.2 kW 1 piece discharge belt (short), no. 17, dimensions 4,350 x 1,200 mm, drive power 1.5 kW 1 piece discharge conveyor, no. 23, dimensions 8,300 x 1,000 mm, drive power 3.0 kW 1 piece bunker belt BB1 (from Hartner ballistic separator) dimensions 25,400 x 2,000 mm 1 piece bunker belt BB2, dimensions 24,000 x 2,000 mm 1 piece bunker belt BB3, dimensions 24.000 x 2.000 mm 1 piece bunker belt BB4, dimensions 11,000 x 2,000 mm 1 piece long discharge conveyor to the warehouse, No. 22, dimensions 28,200 x 1,000 mm, drive power 9.2 kW Technical data of the ventilation system for the sorting cabin: Manufacturer VTS Ventus, Poland Type VS-120-R-H/S Cebvou Tg Tyjmk Ifogt Min. air capacity 5,815 m³/hour Max. Air flow rate 17,610 m³/hour Connected load 108 kW Static pressure 837 Pa Stand-by pressure 600 Pa Filter designation VS 120 B.FLT F5, type EU5 Filter size 592 x 287 mm Remark: The plant is located in Germany, is still fully assembled, connected to electricity and could be inspected in operation (without material input) if required. The sale of the plant takes place ex location, Germany. The dismantling and loading of the entire plant as well as the broom-clean handover of the hall is at the risk and expense of the buyer. Technical documentation for the system and the components is only available in German. An inspection of the plant is possible by arrangement. We do not accept any liability for the technical details or any errors.

Condition: good (used), Year of construction: 1994, operating hours: 51,551 h, Functionality: fully functional, pressing force: 78 t, bale weight: 850 kg, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale height: 720 mm, bale width: 1,100 mm, overall weight: 24,000 kg, oil tank capacity: 900 l, A complete baling system is for sale, consisting of a conveyor belt with feed hopper, the baling press with bale chute and wire pulling stations, without wire. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Type HBC 80 AF Year of construction 1994, overhauled by the manufacturer Bollegraaf 2003 Operating hours 51,551 hours, as of December 2024 Number of pressed bales 613,446 pieces, as of December 2024 Main press pressing force 78 tonnes Pre-press pressing force 45 tonnes Dimensions of feed chute 1,500 x 1,100 mm (l x w) Filling volume / pressing cycle 2.9 m³ Theoretical cycle time 22 seconds Throughput capacity under operating conditions 300 - 450 m³/hour Bale dimensions 1,100 x 720 mm (w x h), the length is variable Drive power 45 kW Connected load, total 60 kW Tying 5-fold vertical, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 10 tonnes/hour Bulk weight of 50 kg/cbm approx. 18 tonnes/hour Bulk weight of 100 kg/cbm approx. 30 tonnes/hour Throughput in whirling mode approx. 20 tonnes/hour Bale weights with a bale length of approx. 1.2 m approx. 550 - 850 kg Hydraulic oil tank capacity 900 litres SPS control manufacturer Schneider Electric Transport weight of baler approx. 24 tonnes Accessories: Conveyor belt with feed chute, bale chute and wire pulling stations Condition of the baler: The machine was completely overhauled by the manufacturer Bollegraaf in 2003 and later fitted with a new PLC control system from Schneider Electric. The baler was used to compress dried grass into bales. Despite its age, the entire system, including the conveyor belt, is in really good condition and has been regularly serviced. The system is still fully assembled, connected to the power supply and can be inspected during operation without the use of materials. Scope of delivery for the baler: Baling press with conveyor belt, feed hopper, wire drawing stations and bale chute. Cgjbvmjvf E Dask Ifjt Comments: Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 2013, Condition: used, We offer you a used PET bottle crusher of the manufacturer BOREMA, type R-1200 F, year of construction 2013, for residual emptying, deaeration and pre-compaction of the fed PET bottles, from 0.3 up to 2.5 l content. The machine has a chassis and can be moved into and out of the feed chute of your baler. The machine has a throughput capacity of approx. 85,000 bottles/h, corresponding to approx. 3t/h. We have the following technical information: Manufacturer: BOREMA Umwelttecjhnik AG Cgsbvmeu Thpnok Ifot Type: R-1200 F (with trolley for retracting and extending) Year of manufacture: 2013 Drive power: 11 kW Connected load: 15 kW Rated current: 32 A Back-up fuse: 40 A Type of construction: Continuous system Function: Double rotor press system Rotor pretension pneumatic: approx. 16t Overload protection: by anti-blocking system Input material: PET disposable and returnable empty bottles 0.3 to 2.5 L capacity Input material: HDPE bottles and canisters up to 3 l capacity Throughput capacity: approx. 3 t/hour, corresponding to approx. 85,000 bottles/hour, depending on size Required compressed air output: G1/2", 8 bar, 40 l/min. Compression ratio: 1:3 Flange dimensions inside: 972 x 1220 mm Feed opening: 565 x 1280mm Weight: approx. 2500kg Possible applications: Due to the chassis, the PET flattener can be moved into the feed chute of your baler as required, thus ensuring residual emptying, venting and pre-compaction of the fed bottles and canisters. When the material is changed, the PET flattener is simply moved out of the feed chute again and paper, cardboard, film, etc. can now be pressed further without using the flattener. Process of the BOREMA PET crusher: The plastic packages are drawn in by two rotating shafts. One of the rotating shafts is pneumatically pretensioned by two air bellows and presses the PET bottles with 16 t of pressure against the second rotating shaft. In the process, the closed plastic bottle is squeezed together, caused to burst and vented. Residual liquids run out and the material falls into the baler in a precompressed state. When impurities are introduced, the pneumatically pre-tensioned shaft deflects to the side and the impurities are channeled through. Significant advantages compared to conventional PET perforators with punching mandrels or knives: The BOREMA process is much more efficient and less subject to wear than conventional PET perforators with punching mandrels or knives. The biggest advantage is that any foreign matter such as metal parts, stones, bottles with frozen contents and pieces of wood are passed through the pneumatically deflecting rotor shaft without stopping the operation of the system or causing any major damage. With conventional perforators, mandrels or blades sometimes break off or become so jammed with the interfering material that the plant has to be shut down and repaired at great expense. Comments: The crusher is in good condition, was dismantled from the running operation, stored, is available at short notice and after assembly immediately ready for use. The documentation (manual, CE, electrical/hydraulic circuit diagram) is complete. An inspection is possible by arrangement. The technical information is taken from sales brochures, the operating instructions or other information provided by the manufacturer. We accept no liability for incomplete or incorrect data and informations.

Year of construction: 2013, Condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Cjbvou Tg I Demk Ifjgt Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: used, For sale is an almost new bale opener line from a paper recycling plant for the production of ‘fluff pulp’ (long-fibre cellulose) from unmixed paper and cardboard production waste. The entire system was newly installed in 2021 and unfortunately never went into production. In 2024, the final decision was made to dismantle the entire system technology and sell parts of it. The resulting bale opener line only ran for approx. 2 hours in set-up mode after installation and never went into production. The system was designed for a throughput of 20 tonnes of fluff pulp per hour. Technical data on the used bale feed conveyor: Manufacturer Bollegraaf Recycling Solutions B.V. Cjbvmkeu Tg Nbe Ifogt Type HBT 1400/1200 * 12500 - 0° (chain belt conveyor) Overhaul of the conveyor belt in 2021 Operating hours after overhaul approx. 2 hours Effective width 1200 mm Belt length 10,150 mm Drive power 3 kW, the belt speed of the motor can be regulated via a frequency converter Belt speed 1.6 - 5.5 m/minute Belt type 250/2, 3+1, thickness 6.1 mm, the belt is without carrier Technical data for the bale opener and dewiring unit: Manufacturer Cross Wrap OY Type DW 1400 dewiring unit Year of manufacture 2021 (new machine) Operating hours approx. 2 hours (exclusively set-up operation by the manufacturer Cross Wrap) Min./max. permitted bale dimensions: Height min. 700 mm, max. 1400 mm Width min. 700 mm, max. 1400 mm Length min. 1100 mm, max. 2500 mm Bale weights min. 250 kg, max. 2000 kg Bale materials Paper, cardboard, plastic films, plastics, pulp and various other recycling materials Throughput capacity up to 60 bales per hour, depending on material Remark: The bale opener and dewrapper is a new machine, built in 2021 and was operated exclusively by the manufacturer Cross Wrap for approx. 2 hours in set-up mode. The system works fully automatically. Bales are held on the infeed conveyor belt by two hydraulically operated grippers. The bale opener follows the contour of the bale and automatically cuts through the wrapping film and the steel or plastic bale wires with a hydraulically driven, rotating knife. The hydraulically driven gripper system holds the film with the steel or plastic bale wires and pulls them out sideways after the opening process. Finally, the wires and film are wound into small coils via a winding unit and ejected into a box via a side chute. Once the bale has been opened and the film and wire removed, it is discharged into the storage bunker with a dosing drum using a conveyor belt. It is then broken down into several pieces. Remark: The feed hopper with dosing drum (drumfeeder) is used, built in 2014 and was overhauled in 2021. After the overhaul and assembly, the conveyor belt has only been in operation for approx. 2 hours in set-up mode. Comments: Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Technical data PaperSpike 2 G: Manufacturer Grumbach und Petermann GmbH Type 2500 Year of construction 2019 Dimensions accelerator belt 3,000 x 2,980 x 600 mm (l x w x h) Weight 1,100 kg Dimensions PaperSpike sorting unit 2,480 x 2,982 x 1,805 mm (l x w x h) Weight 3,100 kg Dimensions PaperSpike 2G complete 5,450 x 3,480 x 1,805 mm (l x w x h) Weight 4,600 kg Dimensions paper discharge conveyor 3,400 x 1,200 x 650 mm (l x w x h) Weight 400 kg Electrical equipment of the entire system: Cgsbju Tg Sisvmk Ifjt Voltage 380 - 420 V Connected load 9.5 kW Current consumption 20.34 A Operating principle: The material is fed in as dry and thin a layer as possible, preferably a monolayer, evenly over the entire width on the accelerator belt. The sorting roller with the spikes pulls the mixed paper from the chute, while cardboard boxes are impaled and held by the spikes. Material (paper) with low stiffness (newspapers, magazines, brochures, etc.) is not held by the spikes and falls into a paper bunker or onto a discharge conveyor after the chute. The spiked cardboard boxes are knocked off the sorting roller by the knock-off shaft and then fall onto the cardboard removal belt or into a separate bunker. Throughput capacity: Depending on pre-sorting, the nature of the feed material and machine settings, between 10 and 12 tonnes per line, per hour can be processed. Scope of delivery: 2 pieces PaperSpike 2G incl. 2 geared motors 2 pieces accelerator belt incl. gear motor 2 pieces paper discharge belt incl. gear motor (The cardboard discharge belt is not for sale and is therefore not included in the delivery! There are two lines available for sale. Depending on the customer's request, either one unit or both units together are sold. The sales price always applies to one unit. Comments: The plants are expected to be dismantled by the end of October and will then be ready for loading. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Technical data IFE cascade screens (vibrating waste screens): Manufacturer IFE Aufbereitungstechnik GmbH, Austria Type SM 2400 x 5000 F - UW30 Year of construction 2009 Drive motor 22 kW Rated current 43 A Screen dimensions overall 5,000 x 2,400 mm (l x w) Dimensions of individual sieve segment 950 x 800 x 130 mm (l x w x d) Cjbvju Tg Rrjmk Ifogt Screen hole grid 150 x 125 mm Length of screen fingers (steel tubes in front of the screen segments) 400 mm Swing width max. 18.5 mm Weight approx. 6,600 kg Possible applications: The waste screen is suitable for use in plants for sorting household waste, commercial and industrial waste, paper and cardboard, scrap metal and electrical waste. Blockage-free screening with the most difficult feed materials, with high throughput capacity, no pigtail formation with oversize particles, loosened oversize particle discharge over the entire screen width and no downtimes for screen cleaning are the greatest advantages of this plant technology. Remark: The screen plates / screen segments have been covered with steel plates without a screening function over the course of time for use in the paper sorting system. The steel plates are only attached and can be removed again. Remarks on the overall layout: Technical documentation for the machine is only available in German. An inspection of the machine is possible by arrangement. We do not accept any liability for the technical data or any errors.

Condition: good (used), Year of construction: 2019, operating hours: 673 h, Functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale height: 1,100 mm, bale width: 720 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (5) Year of construction 2019 Operating hours 673 hours, as of August 24 Number of pressed bales 1,127 bales, as of August 24 Pressing force main press 60 tonnes Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Cgjbvmk Isu Thicofet Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2012, operating hours: 18,593 h, Functionality: fully functional, pressing force: 140 t, bale weight: 1,300 kg, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale height: 1,100 mm, bale width: 1,100 mm, overall weight: 47,000 kg, nominal current: 470 A, Technical data baler: Manufacturer Bollegraaf Typ HBC 140 K Year of construction 2012 Working hours 18.593 hours, stand September 2024 Press power main press 140 tons Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm Capacity per cycle time 4,34 m³ Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm Driving motor 2 x 75 kW Connected load 248 kW Full load current 470 A Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 800 up to 1300 kg, depends on material and bale lenght SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 13,200 x 2,750 x 7,344 mm (l x w x h) Transport dimensions only baler 13.200 x 2.750 x 3.450 mm (l x w x h) Machine weight baler approx. 47 tons Special equipment: 2-flap pre-compressor for large cardboard boxes and octatainers Cgjbvju Thy Esmk Ifst Wirbulator for magazines and books Comments: The press is currently in operation and is to be replaced by a new machine in the second calendar week of 2025. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2016, Functionality: fully functional, conveyor belt length: 18,000 mm, conveyor belt width: 2,000 mm, power: 5.5 kW (7.48 HP), Equipment: type plate available, Technical data feeding conveyor belt: Cobou Tg Udevmk Ifogt Manufacturer Bollegraaf Typ HBT 1216/2000 * 18000 Year of construction 2015 Driving motor 5,5 kW Length feeding conveyor 18,000 mm Grade 0° Effecting width 2,000 mm Height of side wall feeding conv. 500 mm Transport dimensions 18,000 x 3,200 (2,830 mm without motor and gear) x 1,200 mm l x w x h Weight approx. 13 t Comments: Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, For sale is a sorting plant for commercial waste, paper, cardboard, plastics etc., year of construction 2022, only 151 operating hours, with a sorting capacity of up to 20,000 tonnes/year, in two-shift operation. The plant consists of the following components: 1 piece feeding / dosing hopper with steel slat conveyor and a dosing drum, manufacturer Bollegraaf, type BDF-1200/2000 1 piece ascending conveyor between the feed hopper and the sorting cabin, manufactured as a troughed conveyor, manufacturer Lubo Systems, type TBM 2000 x 15000 1 piece sorting cabin, air-conditioned (heated), measuring 14,500 x 5,732 x 3,270 mm (l x w x h), with 4 sorting stations, 8 discharge chutes and 5 material bunkers underneath. The concrete blocks are not included in the scope of delivery of the sorting system. 1 piece sliding belt conveyor as sorting belt, manufacturer Bollegraaf, type HBGT 250/1400 * 15000 1 piece ventilation system for the sorting plant with an air capacity of 8,000 m³/hour, heated with 93.8 kW electrical heating power, manufacturer MANDIK. The area required to install the sorting system in its current configuration is at least 46 x 7.5 m (345 m²). The height of the sorting cabin including the ventilation pipes is 7,370 mm. Remark: The system is located in Germany, is still fully assembled, connected to electricity and could be inspected in operation (without the use of materials) if required. The plant is sold ex works. The dismantling and loading of the entire system as well as the broom-clean handover of the hall is at the risk and expense of the buyer. The owner can provide sporadic logistical support during dismantling with forklift trucks, wheel loaders and excavators. Technical documentation for the system and the components (operating instructions, CE declaration, electrical and hydraulic circuit diagrams) is only available in German. The existing control cabinet controls all of the customer's machines in two halls and is therefore not included in the scope of delivery of the sorting system. The control cabinet is disconnected on site, dismantled and remains with the previous owner in order to be able to continue operating the remaining systems on site. Only the frequency converters for the individual machines of the sorting plant are included in the scope of delivery. The concrete blocks under the sorting plant are also not included in the scope of delivery and remain with the previous owner on site. Cobveu Tg S Ajmk Ifjgt A viewing of the plant is possible by appointment after the prospective buyer has sent the complete company details (self-certification) and a subsequent credit check. We accept no liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 2009, operating hours: 20,536 h, Functionality: fully functional, pressing force: 80 t, bale weight: 600 kg, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale height: 750 mm, bale width: 1,100 mm, net weight: 16,000 kg, nominal current: 75 A, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: Due to a reorganisation of the manufacturing processes within the company, a new baling line is being built in a new hall. The old baling press with conveyor technology is therefore no longer required and is expected to be available for sale at the beginning of 2025. Technical data for the chain belt conveyor: Manufacturer not known Type not known Length of feed belt 5,300 mm Length of ascending belt 12,700 mm Overall height 7,300 mm Useful width 1,200 mm Unfortunately, no further technical data, documentation or drawings are available. Condition of the press system: The entire system is in very good condition and is regularly cleaned and maintained by the operator. The quality of the bales is exceptionally good, as you can see from the photos of the pressed bale goods. Even hard plastics such as plastic crates, PP bucket chains and PE plastic drums were pressed into dimensionally stable bales with the fourfold vertical binding. Tidiness, cleanliness and maintenance of the systems are practised in this company and not just written on the website. Scope of delivery: Avermann baler, type AVOS 1410-45/80, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 Comments: Cjbvmkju Thyps Ifsgt The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available in full. Unfortunately, there is no more documentation for the conveyor belt. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 2022, Functionality: fully functional, Technical data on the EPS (Polystyrene) press: Manufacturer FZ-Recycling GmbH & Co. KG, Germany Type FZR 320 Year of construction 12/2022 Drive power shredder 4 kW Drive power of compactor screw 7.5 kW Drive power hydraulic unit for the holding clamp in the press channel 1.1 kW Total connected load 12.6 kW Current consumption 32 A Compaction ratio of the compacted blocks to the original product approx. 50:1 (depending on material) Block weight after compaction approx. 300kg/m³ (depending on material) Block dimensions 320 x 320 mm, variable length Throughput approx. 100 kg/hour, depending on material Achievable density approx. 250 - 300 kg/m³ The pressed blocks are stacked approx. 1400 mm high on pallets and stretch-wrapped. Machine dimensions approx. 4,600 x 1,400 x 1,980 mm (l x w x h) Transport weight press 1,325 kg Cgsbvmkou Thkaj Ifet Condition of the baler: The press was only used sporadically, is in very good condition and available at short notice. Due to the low weight of the machine and the forklift shoes in the transport frame, the press is mobile and can be used directly on the construction site where the material is produced. The electrical connection is made via a CEE 32 A plug. Scope of delivery for the baler: 1 piece EPS press, ready for connection and use Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: excellent (used), Year of construction: 2023, operating hours: 1,851 h, Functionality: fully functional, pressing force: 70 t, bale weight: 500 kg, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale height: 750 mm, bale width: 1,100 mm, overall weight: 17,000 kg, oil tank capacity: 70 l, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410 BS-22/50 Year of construction 2023 Pump operation hours 1,851 hours, as of July 24 Press power main press 70 t (a 70 tonne hydraulic cylinder is installed, special equipment) Specific press force 90,9 N/cm² (a 70 tonne hydraulic cylinder is installed, special equipment) Feed channel 1,400 x 1,000 mm Theoretic cycle time 13 sec Theoretic throughput capacity 266 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 22 kW Connected load 65 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 5,5 t/h bulk weight of 50 kg/cbm approx. 7,5 t/h bulk weight of 100 kg/cbm approx. 9,7 t/h Cgebvju Thbxsmk Ifst Bale weight with a bale length of approx. 1.2 m up to 500 kg, depends on material SPS controller Siemens S7-1500 Operating panel Schneider Harmony Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 17 t Special equipment: Wear-resistant floor made of HARDOX steel Larger main hydraulic cylinder with 70 tonnes of pressing force Special press ram for pressing loose bulk materials with small grain sizes OptiCut XS system for lower cutting forces and higher throughput rates Special pressing piston for pressing "difficult" materials Technical data for the conveyor belt: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Deutschland Type KGF GB 1500 Year of construction 2023 Drive power 4.0 kW Belt speed approx. 0.3 m/second Length feeding conveyor 2,679 mm Length elevating conveyor 6,866 mm Length goose neck 1,272 mm Grade 35° Effecting width 1,400 mm Side wall height 800 mm Carrier height 50 mm Carrier distance 750 mm Belt quality EP 400/3, 3:1 (DIN quality N) Overall height 4,515 mm Overall transport dimensions11,148 x 2,502 mm (l x w) Technical data on the non-contact personal protection system: Manufacturer BOREMA Umwelttechnik AG, Switzerland Type APSS iBOR 22 Year of construction 2023 Condition of the press system: The entire system is in very good condition due to the short operating time of only 1,851 pump hours and the processing of only paper, cardboard and film. Scope of delivery: Avermann baler, type AVOS 1410 BS-22/50, incl. wire drawing stations and bale chute Avermann conveyor belt, type KGF GB 1500 BOREMA personal protection system, type APSS iBOR 22 Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.