Conical mixer , Type HV-1500 SS, Year of construction ++ NEW ++, Material Stainless steel 1.4301 (304), Capacity 1500 Ltr, Largest cone diameter 1865mm, Cone height 2500mm, With stainless steel arm , Top drive , Motor 4,0 KW, 400 Volt, Bottom bearing pintle bearing , Bottom discharge , Outlet with sliding valve , Weight 800 KG, Extra Specifications delivery time: 12-16 weeks, possible options: lumpbreaker, installation of liquid injection system, slide plate valve pneumatic operated, bridgebeam ...
- New Herbold screw crusher SB 560/2 used (year 2006, taken over used and overhauled, since 2012 in operation)
- Two screw shafts each 560 mm diameter
- hopper opening: approx. 1600 mm x 1600 mm
- Drive power: 2 x 15 kW
- Due to the reconditioning of EPS only minor wear marks
- Approx. 11,000 operating hours
- Used for breaking up EPS (polystyrene) bales
Bsgutwh93d
- One motor was replaced
- One fastening between shaft and V-belt housing was welded
- A plate on the V-belt housing was removed and...
material: PUR Schaum
Rotor-Ø: 315 mm
compressed air: 6 bar
dimensions L x W x H: m
The milling plant with milling and opening-up machine REKORD BR-ex
Ysfwff79
(explosion proof up to 3 bar absolute) is intended exclusively for grinding PUR (polyurethane) foam.
Data of the processable material:
- pre-comminuted PUR foam pieces max. 20mm
- humidity so that milling is still possible
- throughput volume=approx. 130kg/h
Drives:
- 5 drives (all geared motors) for roller dosing units, mill drive (squi...
Cutting Mill THM CM100
(Andritz Mewa USM 1000)
Converts large into small
Ideal for cutting into small pellets
The THM CM cutting mill is the right choice for cutting pre-reduced parts into smaller granules. Size reduction is accomplished by a wear-resistant rotor with rotating knives that cut against the stator blades.
The final grain size depends on the size of the screen openings. The granules are discharged pneumatically through the discharge chute by means of a discharge auger at the bottom ...
Ballshaping- and Delaminationmill
Molinator for fine delamination!
Cuzkcxhq
Diverse Types: RW VKR16/3 / 22-37kW and RW VKR 22/3 / 75-110kW
Input Composite Material Examples: Regrind from hair-wire, printed circuit boards, electronic circuits, other composited material.
Al / Plastic, Cu / Plastic, Cu / Glass fibre, ABS / Plastic fibres, etc.
Type selection: depending on the material / depending on layer thickness / depending on test‘s / according to the desired throughput.
Description Molina...
“Pallmann PHPH 16-23 Grizzly” for Sale
Also many other manufacturer like: Sandvik-Aubema / Hazemag
Find our complete stock on our website.
Manufacturer: Pallmann
Kpeowzu
Type: PHPH 16-23 Grizzly
Rotor Dia.: 1.600mm
Rotor Width: 2.300mm
Electrical Motor: Included
Included frame and feeders.
Conical mixer , Make FOETH BV (NL), Type HV-3000 SS, Year of construction ++ NEW ++, Material Stainless steel 1.4301 (304), Capacity 3000 Ltr, Largest cone diameter 2292mm, Cone height 3200mm, With stainless steel arm , Top drive , Motor 5,5 KW, 400 Volt, Bottom bearing pintle bearing , Bottom discharge , Outlet with sliding valve , Weight 1000 KG, CE , Extra Specifications delivery time: 12-16 weeks, possible options: lumpbreaker, installation of liquid injection system, slide plate valve pneum...
- New Herbold granulator LM 600/1000-S5-2 used (BJ 2017).
- rotor width: 1000 mm
- rotor diameter: 600 mm
Bsgurannh0
- stator knives: 2
- rotor knives: 5
- hopper opening: approx. 980 mm wide x 700 mm high
- drive power: 55 kW
- without conveyor fan
- 3.370 operating hours
- Used for re-shredding EPS (polystyrene)
- Due to the preparation of EPS and few operating hours only minor wear marks
- Included: two sets of rotor knives (one set ground, one set used)
- Two sets of stator knives (one set u...
Producer: TPA TRITURATORI Spa / RECONA
Bp9cwug7uo
Model: MCE –S 2500
Year of production: 2004
Number of shafts / rotor: 1
Inlet opening: 2500 x 1800mm
Rotor length with combs - 2620 mm (working 2500mm)
Rotor diameter - about 700 mm
Weight: 22 tons
Hydraulic power unit: OLEODINAMICA CSP
Electric power supply and control cabinet
Steel elements - supporting structure for the crusher
Charging hopper - steel (2600x1900x800 mm)
Shredder for recycling TPA - waste disposal line - single-shaft electric c...
UNIVERSAL GRANULATOR Andritz MeWa UG1008
Single-shaft shredder
MEWA UG 1008 MS - UNI - CUT, Single shaft shredder, Granulator.
Year of manufacture: 2005
Power supply: 400 V, 50 Hz.
Drive: 160 kW.
Rotor width: 1050 mm
Rotor diameter: 800 mm
Dimensions of cutting chamber: 1000 x 800 mm
Number of knives on the rotor: 25 pcs. (new)
Number of counter knives: 5 pcs. (new)
Bsfeaaoii9
Sieve: mesh 40 mm (new) to choose
complete control cabinet
Machine dimensions approx: 6000 x 2400 x 4000 mm
Shredding:
-...
CARBOMA RK 2000 single shaft shredder
A device used in many industries, recommended for crushing such materials
as: municipal waste, construction waste, glass, ceramics, paper, cardboard, wood, plastic,
organic substances, fabrics, tires, aluminum, metal, electric and electronic scrap, batteries and
batteries, car engines etc.
Manufacturer: CARBOMA
Model: RK 2000
Bhcidty238
Production year: 2016
Max power: 160 kW
Total weight: 14.300 kg
“Hazemag Universa 1620” for Sale
Manufacturer: Hazemag
Type: Universa 1620
Rotor size: 1.600 x 2.000 mm
Inlet size: 2.500 x 2.000 mm
Crusher Weight: 34.400 kg
Owj7r
Lödige mixer , Make Gebruder Lödige Maschinenbau GmbH, Type FKM-1200D, No. 9933, Year of construction 1981, Material Stainless steel 1.4571 (316Ti), Working pressure jacket 8 Bar, Capacity 1200 Ltr, Trough sizes dia.950mm x1700mm, Inlet dia.340mm, Top connections dia.240mm, Inspection hatch (2x)540x390mm, Outlet 240x280mm, With jacket 130 Ltr, Max. temperature 174 degr C, With adjustable packing glands , Motor 37 KW, 400/690 Volt, Speed mixing shaft +/- 60 rpm, With lump breaker (2x), Motor 5,5 ...
I sell shredder n.4 shafts with the grid 35mm + mill under n.3 rotating blades + n.2 against blades grid 8mm, plant complete with belt feed, fan for extraction of material, cyclone with filter and dust collector, fan for fumes, door castle BIG BEGS
Cjo98jz0u
Plant and been completely painted and overhauled also available for testing, thanks.
Herbold SML 60/100 - H5/2
75 kW Drive
10 rotor blades, 2 stator blades
Cq3f2ba3
Rotor diameter: 600 mm
Rotor width: 1.000 mm
incl. suction, dedusting, demetallization, double Big Bag bagging
The system is built into a semi-trailer and soundproofed.
Crushing Mills suitable for many applications, example for steel slag, non-ferrous, iron ore and incinerator bottom ash.
Capacity 100-300Tn per hour.
20x2en
CARBOMA single shaft shredder
The device is used for final shredding of plastics, mixed municipal waste, electrical wires, electronics, rubber, glass, ceramics, paper, cardboard, wood, etc.
Muupnc
Manufacturer: CARBOMA
Model: PURSAN 2000
Production year: 2017
Max power: 160 kW
Total weight: 15,000 kg
Rotor diameter: 600 mm
Working shaft speed: 80-200 rpm
Capacity: up to 12 tons (depending on the type of material being shredded)
PET perforator pierces bottles, releasing air from them, which greatly simplifies the process of pressing into bales. Grinding unit includes two needle drums in the body. The drums are driven by gear motors through a worm drive.
Our engineers will design placement options within your MSW sorting facility.
Bkd22jsxcp
Conical mixer , Type HV-2000 SS, Year of construction ++ NEW ++, Material Stainless steel 1.4301 (304), Capacity 2000 Ltr, Largest cone diameter 1936mm, Cone height 2800mm, With stainless steel arm , Top drive , Motor 4,0 KW, 400 Volt , Bottom bearing pintle bearing , Bottom discharge , Outlet with sliding valve , Weight 900 KG, Extra Specifications delivery time: 12-16 weeks, possible options: lumpbreaker, installation of liquid injection system, slide plate valve pneumatic operated, bridgebeam...
This cutting mill is suitable for crushing non-conforming plastic material, such as intakes and smaller parts.
Technical parameters
Condition: used equipment - renovated. Fully functional and ready to use
Rotor diameter: 300 mm
Rotor width: 600 mm
Driving power: 11 kw
Number of rows of rotor blades: 3
Number of rows of stator blades: 2
Sieve perforation:> 6 mm
Weight: approx. 1 t
Color: blue
Number of available pieces: 4
Oc8vt
Capacity: The average power depends on the material loaded and the m...
75kw-motor comes with various screens
Coru9w8c
Wire grinding plant, with an hourly grinding average of 350-450 Kg of a mix type electric cables , which contains 50% of copper, the plante is composed with:
-Shredder 0.37kW
-Conveyor belt 3200 mm lenght
-Magnetic table
Bdn0rma3qa
- Water densimetric table
- Dust Aspirator
- Electric Cabinet
1pc ball mill / single chamber
* Manufacturer CEMENTAS GmbH Austria
* Type , dry grinding SINGLE CHAMBER
Diameter 2.15 m x length 6.75 m (bottom)
* Year of construction 1960/1998 conversion
Muyr3c
* Feed material e.g. calcium carbonate
* Feed size µ (0 -400) max .4 mm
* Throughput capacity 20to/h
* Finished product quantity after separator approx. 2.5 to/h
* End product approx. 10µ
* grinding track length 6.40 m
* Filling degree 20%
* Mill speed 20.36 min-1
* installed main engine approx. 250 kW...
Please find Typ ProCom in the attached pdf-document.
The grinding plant is a test-plant with a very little used impact rotor mill in combination with used peripherals (storage hopper, feed conveyors, rotary valve, exhaust filter with rotary valve, exhaust fan etc. All cpl. ready for operation. With switch cabinets. Removable. Mill with frequency converter.
Le9gh
Conical mixer "Millmix", Make Hosokawa Nauta Haarlem bv, Type D2RX, No. M20511, Year of construction 1983, Capacity +/- 2000 Ltr (nett), Largest cone diameter +/-2150mm, Cone height 2200mm, Manhole dia.500mm, With stainless steel arm (2x), Top drive , Motor Screw +/- 11 KW, Motor Arm 1,1 KW, 220/380 Volt, Cantilevered screw (2x), Outlet with sliding valve (200x200mm), With lump breaker "Rotojet disperser", Motor 22 KW, 380 Volt, Suitable for liquid injection , With switchgear , Floor space 2,5x2...
This crusher is suitable for pre-crushing materials. From the plastic industry, these are mainly lumps, overflows.
Technical parameters
Condition: used equipment - renovated. Fully functional and ready to use
Inlet hopper: 600x840 mm
Rotor diameter: 250 mm
Rotor width: 600 mm
Bloiw37c2l
Power: 15 / 18.5 / 22/30 kw
Rotor knife: 26 pcs
Sieve mesh size: 10 - 40 mm
Weight: approx. 1.4 t
Color: blue
Number of available pieces: 1
Capacity: The average power depends on the material loaded and the mesh...
1used ball mill /2-chamber system
diameter 2,4m x length 6,40m
* Manufacturer CEMENTAS GmbH Austria
* Type 2 separate grinding chambers with product entry on both sides and
* central discharge, dry grinding
* Year of manufacture 1997
* Feed material e.g. calcium carbonate, bentonite
* Feed size µ (0 -400)
* Finished product quantity after separator approx. 6 to/h
* End product approx. 10µ
* grinding track length 2x 2,95m
* Mill speed 20.36 min-1
* installed main motor approx. 340 kW
* grinding m...
Conical mixer , Make Foeth BV (NL), Type HV-50 SS, Year of construction ++ NEW ++, Material Stainless steel 1.4301 (304), Capacity 50 Ltr, Largest cone diameter 730mm, Cone height 860mm, With stainless steel arm , Top drive , Motor 0,75 KW, 400 Volt, Cantilevered screw , Bottom discharge , Outlet with sliding valve , Polished inside (Ra 0,8, K220), Mounted on legs , Weight 250 KG, CE , Extra Specifications delivery time: 12-16 weeks, possible options: lumpbreaker, installation of liquid injectio...
1 pc. used ball mills,
Manufacturer: MIAG Germany
Pipe length 11,00 m
Pipe diameter 1.80 m
Capacity approx. 20? to/h
Bijeirnsdu
Ready for use with filter system (dedusting)
Bearings, electric motor 360 KW, Flender gear type TE-750, control system,
as spare parts: bullets +armour plates +screws for armour plates
The ball mill is of very high quality and sturdy construction.
All components (gearbox, bearings, cylinders, control system are newly installed, overhauled, new interior armouring
at cal...
Conical mixer , Type HV-600 SS, Year of construction ++ NEW ++, Material Stainless steel 1.4301 (304), Capacity 600 Ltr, Largest cone diameter 1608mm, Cone height 1844mm, With stainless steel arm , Top drive , Motor 3,0 KW, 400 Volt, Bottom bearing pintle bearing , Bottom discharge , Outlet with sliding valve , Weight 650 KG, Extra Specifications delivery time: 12-16 weeks, possible options: lumpbreaker, installation of liquid injection system, slide plate valve pneumatic operated, bridgebeam in...
Conical mixer , Type HV-1000 SS, Year of construction ++ NEW ++, Material Stainless steel 1.4301 (304), Capacity 1000 Ltr, Largest cone diameter 1672mm, Cone height 2184mm, With stainless steel arm , Top drive , Motor 3,0 KW, 400 Volt, Bottom bearing pintle bearing , Bottom discharge , Outlet with sliding valve , Weight 700 KG, Extra Specifications delivery time: 12-16 weeks, possible options: lumpbreaker, installation of liquid injection system, slide plate valve pneumatic operated, bridgebeam ...
Conical mixer , Type HV-300 SS, Year of construction ++ NEW ++, Material Stainless steel 1.4301 (304), Capacity 300 Ltr, Largest cone diameter 1420mm, Cone height 1530mm, With stainless steel arm , Top drive , Motor 3,0 KW, 400 Volt, Bottom bearing pintle bearing , Bottom discharge , Outlet with sliding valve , Weight 600 KG, Extra Specifications delivery time: 12-16 weeks, possible options: lumpbreaker, installation of liquid injection system, slide plate valve pneumatic operated, bridgebeam in...
Make BBA Innova AG Process Engineering (CH), Type CCC-95/60, No. V-95602, Year of construction 2006, Material Chromed steel, Working pressure 8 Bar, Roll cooler , Double roll , Rolls chromium plated , Roll sizes Cooling drum dia.950mm, Squeezing drum dia.260mm, Water heating , With knife discharge for flakerunit, Motor 2,3 KW, 380-480 Volt, With jacket , Mounted on wheels , With switch , Floorspace 2,0x1,4 M, Total height 1,5 M, Weight 2000 KG, Extra Specifications - outlet with breaker , Extra ...
Roll breaker , Make F Wilhem Steuber, Type S 500, Material Mild steel, Fluted rolls dia.300mm x500mm, Inlet 470x200mm, Outlet 600x500mm, funnel dia.170mm, Motor 3.6 KW, 380Volt, Roll speed +/-260 rpm, With roll feeding , Floorspace 2,0x0,8 M, Total height 1,6 M, Weight 1000 KG What you can expect from Foeth: all our machines are in working condition, and at a reduced price compared to new. They are ready for shipping to any destination worldwide. You are welcome to inspect our machines in Barnev...
Lödige mixer , Make Morton Machine, Motherwell Scotland, No. 22628, Year of construction 1979, Material Stainless steel, Working pressure jacket 1.7 Bar, Capacity 3000 Ltr, Trough sizes 1120x2950mm, Inlet Dia.300mm, Top connections (2x)Dia.80mm, Inspection hatch 600x460mm en inlaat, Outlet 300x250, With jacket , With adjustable packing glands , Motor 55 KW, 415 Volt (ex), Speed mixing shaft +/- 75 Rpm, Mounted on frame , Floorspace 4900x2500mm, Total height 1600mm, Weight 3300 KG, Extra Specific...
Roll breaker , Make Bühler AG (CH), Type MDDO, No. 10434479, Material Mild steel, Roll sizes (8x) dia.250mm x1500mm, Fluted rolls , With hopper , Inlet dia.150mm, Outlet hopper dia.150mm, Motor "Breaker" 55 KW, 400/690 Volt, Motor "Reduction" 37 KW, 400/690 Volt, With variable speed drive , With roll feeding , Motor , With switch , Floorspace 2,5x1,5 M, Total height +/- 2,6 M, Weight +/- 2000 KG, Extra Specifications With spare rolls, Extra information 8 rolls What you can expect from Foeth: all...
Universal mixer "Single Pot Mixer granulator", Make Gebrüder Lödige GmbH (DE), Type MGT 30, . 11.236, Material Stainless steel 1.4541 (321), Capacity 25 Ltr (nett.), Vessel sizes dia.400mm x225mm, With cover , Manual operated outlet , Outlet DN80, With motor 3,0 KW, 380 Volt (EEx de IICT4), With variable speed drive , With lump breaker , With motor 1,3/1,9 KW, 380 Volt (EEx deIICT4), Rotor speed 1500/3000 rpm, Year of construction 1986, stainless steel frame , Mounted on wheels , With switch , ...
Gral-granulator , Make Machines Collette N.V. (BE), Type GRAL 10, . 95GRS00100070, Material Stainless steel 1.4404 (316L), Capacity 10 Ltr. (nett.6 Ltr), Vessel sizes dia.250mm x180mm, With cover , With motor 1,5/0,85 KW, 380 Volt, Rotor speed 430/660 rpm, With lump breaker , With motor 0,6/0,8 KW, 380 Volt, Rotor speed 1500/3000 rpm, With timer , Year of construction 1995, Mounted on frame , With switchgear , Floorspace 1,0x,4 M, Total height 1,3 M, Weight 200 KG What you can expect from Foeth:...
Roll breaker , Make Bühler AG (CH), Type MDDO, No. 10434480, Material Mild steel, Roll sizes (8x) dia.250mm x1500mm, Fluted rolls , With hopper , Inlet dia.150mm, Outlet hopper dia.150mm, Motor "Breaker" 55 KW, 400/690 Volt, Motor "Reduction" 37 KW, 400/690 Volt, With variable speed drive , Roll speed 380-970 rpm, With roll feeding , Motor , With switch , Floorspace 2,5x1,5 M, Total height +/- 2,6 M, Weight +/- 2000 KG, Extra Specifications with spare rolls, Extra information 8 rolls What you ca...
Roll breaker , Make Bühler AG (CH), Type MDDO, No. 10434471, Material Mild steel, Roll sizes (8x) dia.250mm x1500mm, Fluted rolls , With hopper , Inlet dia.150mm, Outlet hopper dia.150mm, Motor "Breaker" 55 KW, 400/690 Volt, Motor "Reduction" 37 KW, 400/690 Volt, With variable speed drive , Roll speed 380-970 rpm, With roll feeding , Motor , With switch , Floorspace 2,5x1,5 M, Total height +/- 2,6 M, Weight +/- 2000 KG, Extra Specifications with spare rolls, Extra information 8 rolls What you ca...
Universal mixer , Make Niro T.K.Fielder Limited (U.K.), Type PP1 Pharma Matrix, . 8255, Material Stainless steel, Capacity 10 Ltr, Vessel sizes dia.280mm x200mm, With cover , Inlet dia.20mm, With motor 3,0 KW, 240/415 Volt (EEx-d IIB T5), With variable speed drive , Rotor speed 300-1500 rpm, With lump breaker / granulator, With motor 0,55 KW, 240 Volt (EEx-d IIB T4), Rotor speed 1500/3000 rpm, With timer , Year of construction 1994, stainless steel frame , With switch , With switchgear , Floors...
Universal mixer "Vertical granulator", Make GLATT Systemtechnik GmbH (DE), Type VG PRO 400, . 8214, Material Stainless steel 1.4404 (316L), Capacity 390 Ltr, With cover , Pneumatic operated outlet , Outlet dia.200mm, With jacket , With motor 22 KW, With variable speed drive , Rotor speed 5-160 rpm, With lump breaker , With motor 7.5 KW, Rotor speed 300-3000 rpm, Year of construction 2004, stainless steel frame , With switchgear , Floorspace 2.5x2 M, Total height 4.3 M, Weight 3000 KG, CE , ATEX...
Paddle mixer , Make Gericke AG Regensdorf-Zürich, Type Flux batch mixer GMS 1200, No. 1010, Material Stainless steel, Double shaft , Useful capacity 300-960 ltr, Inlet dia.100mm, Manhole dia.250mm, Outlet (1x) 400x100mm, With adjustable packing glands , Motor 11 KW, 380/660 Volt, Floor space 2,5x1,5 M, Total height 1,2 M, Weight 1600 KG, Extra Specifications with lump breaker 3,0 KW, 380 Volt, 2880 Rpm What you can expect from Foeth: all our machines are in working condition, and at a reduced pr...
Hot mixer , Make MTI Industrieanlagen GmbH (DE), Type EM 100 B, No. 835, Year of construction 1998, Material Stainless steel, Working pressure 2 Bar, Capacity 100 Ltr, Vessel sizes dia.580mm x390mm, With jacket (17 Ltr), Max. temperature 95 degr.C., With motor 11,5 KW, 440 Volt, Rotor speed +/- 350 rpm, Pneumatic operated outlet , Outlet dia.220mm, With lump breaker , Motor 3,6/4,8 KW, 380 Volt, With switchgear , Floorspace 2,3x0,8 M, Total height 1,8, Weight 500 KG What you can expect from Foet...
Shredder , Make Kusters Venlo, No. 60193/7, Year of construction 2006, Material Stainless steel, Double shaft , With hopper , Inlet 600x400x240mm, Outlet 150x150mm, Motor 1kW, 3x 400 Volt, Mounted on legs , With switchgear , Floorspace 1,5 x 0,9m, Total height 2,1m, Weight 600kg, Extra Specifications Hopper and breaker are stainless steel What you can expect from Foeth: all our machines are in working condition, and at a reduced price compared to new. They are ready for shipping to any destinati...
