Used hydraulic presses double column / Four column presses for sale (310)

Condition: used, Year of construction: 1995, functionality: fully functional, pressing force: 250 t, table width: 1,600 mm, table length: 2,650 mm, overall weight: 55,000 kg, die cushion stroke: 235 mm, Hydraulic deep drawing press Wanzke GTA 250 year of construction 1995 used Technical data: Pressing force 2,500 kN ram stroke 600 mm ram speed working stroke 25 mm/s Die cushion 1,600 kN Die cushion stroke 235 mm Table clamping surface 2,650 x 1,600 mm Stroke limiting spindles 2 pcs. Damping cylinders 2 pcs. Drive power 75 kW Press dimensions approx. width 4,250 mm (without cladding) depth 2,000 mm height 5,150 mm Weight 55 to. Table: Holes for quills in the center of the press table. From there, the other holes holes have a distance of 150 mm to the right and left There is also a hole in the middle of the press table. The hole spacing is also 150 mm. A maximum of 15 quills are possible lengthwise and 7 widthwise. Fedpfx Agsup Skwo Djpr possible. Quill diameter: 30 mm

Condition: used, Year of construction: 2021, machine/vehicle number: HB 2022-A-073, Portal straightening press with 300 T capacity a) idle and pressing speed up to 17 mm/sec. b) opening speed up to 55 mm/sec c) table size 2500x1600mm d) open height 700 mm e) total size approx. LBH 4500 x 2300 x 3700 mm Fjdpfxsh Agnue Ag Dspr f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) table in grid construction,with T grooves according to customer's request, otherwise 22mm i) operation on swivel arm, mounted on the bridge j) pressure adjustment from 50 T to 300 T via MONITOR k) bridge moves by two gear motors, via racks l) Cylinder moves to the left and to the right via toothed racks m) Machine body double painted n) Cylinder induction hardened Type of construction Press design PORTAL PRESS Thermally neutral 80 - 120 °C Number of operating sides 3 side Forces Pressing force max. 3,000 kN Free ripping force max. 500 kN Pressure build-up time Closed die Steel to steel Max. 3 sec. Dimensions Max. Opening width 700 mm Stroke and min. opening 700 mm/ 0 mm Table height above floor approx. 9ß0 mm Height above floor (headroom) approx. 3700 mm Hall height min. 5.000 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.8 mm/m Weight Total weight of press without operating materials and table plate approx. 22 T Speeds Fast closing with 17 mm sec. Pressing speed 8 mm sec. Opening 55 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel after max. 78 db(A) DIN 45635-T16-KL3 Hydraulics Number of pressing cylinders 1 pc. Operating pressure max. 350 bar Pressing pressure build-up time 02. mz sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH approx. 93 L/min Oil volume approx. HLPD 46 MW 900 liters Ambient temperature max. 45 °C Oil temperature max. 55 °C Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Hydraulic connection Main motor IE3 22 kW Total connection Approx. 30 kW

Condition: excellent (used), Year of construction: 2008, X,Y travel: 14.6" x 10.6" U,V,Z travel: 3.9" x 3.9" x 10.2" Fpjdpfxjwqq Rhs Ag Dor Max. workpiece size: 29.5" x 21.7" x 10.2" Max. workpiece weight: 880 LB Max. X, Y rapid traverse: 31.5 in/min Drive system: AC servo motor/linear motor Wire diameter: 0.004" – 0.012" Max. wire feed: 11.8 in/s Wire tension: 0.44 – 5.52 lb Taper angle: ±21°/4.33 in (DA+DB=0.6 in) Layout (W x D x H): 90.6" x 89.2" x 80.6"

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-250E/NC, pressing force: 250 t, table width: 2,500 mm, table length: 1,150 mm, Equipment: documentation/manual, safety light barrier, HYDRAULIC FOUR-COLUMN PRESS FOR DEEP DRAWING APPLICATIONS TECHNICAL DATA Press force / Main cylinder 250 t Blankholder force 50 t Motor power 11 kW Ram stroke 500 mm Approach speed 80 mm/s Working speed 7 mm/s Return speed 105 mm/s Column diameter 150 mm Maximum pressure 260 bar Usable table area 2,500 x 1,150 mm Column clearance 2,500 x 700 mm Maximum open height 1,000 mm Blankholder (cushion) size 950 x 750 mm Working height 1,100 mm Overall height 3,650 mm Weight 15,000 kg The hydraulic four-column press MV-250E/NC belongs to the M/NC series and is specially designed for high precision and capacity, particularly in deep drawing operations. Outfitted with upper and lower tables made from C45E steel, featuring DIN-650 T-slots to ensure minimal friction during vertical movement of the upper table. This is facilitated by maintenance-free bi-metal bushings and perfect parallelism by means of four chrome-plated and precision-ground cylindrical columns. The press features an optimized hydraulic system operating at pressures below 290 bar, ensuring long service life and reliable performance. It complies with all essential safety and health requirements in accordance with CE regulations. STRUCTURE AND TABLES • Consists of three fully welded blocks, manufactured exclusively from S355JR steel. • Stabilized and machined after welding to ensure perfect parallelism and precision. • Designed and calculated using finite element analysis software. • The lower table is equipped with a 50-ton hydraulic cushion, usable area 950 x 750 mm, and three front supports for tooling outside the press. • Integrated SIEMENS KTP-400 NC for controlling ram stroke, speed changes, and cushion control. • Includes a SIEMENS S7 PLC, permitting storage and programming of up to 99 settings. CYLINDER AND HYDRAULIC UNIT • Single-acting cylinder with honed sleeve, chrome-plated piston, and wear-resistant guides. • Complete hydraulic unit installed on the top of the press. • Hydraulic unit comprises a low-noise Denison hydraulic pump and an air-oil cooler. • Includes: - Decompression system - Solenoid operated pressure valves - Pre-fill valves - Communication valve Fjdpfx Aewkuchog Dopr - Check valve - Pressure relief valve - Safety catch valve ELECTRICAL INSTALLATION AND SAFETY • Features a SIEMENS SIMATIC S7 1200 safety PLC and a 4-inch KTP-400 touchscreen on the control panel. Enables programming of semi-automatic and automatic modes, power, stroke, and dwell time. Offers storage for up to 99 recipes; each recipe is fully programmable for the above parameters. • The electrical control panel features a selector switch for mode selection: manual “setup” or automatic “production” cycle. • Machine operation via electric low-voltage foot pedals. • Safety features include category IV light curtains in the front working area, two fixed side guards, and a rear safety guard with a magnetic interlock detector.

Condition: used, Pressing force 400 kN ,Table 450x560 ,Ram 375x300 ,Distance table-joints 340 stroke 160 ,Through-feed hole 100 diameter ,Safe column passage 220x410 Fpodpfx Asum Uuyeg Dsr

Condition: used, functionality: fully functional, machine/vehicle number: 71737, total length: 1,575 mm, total width: 640 mm, total height: 1,970 mm, overall weight: 645 kg, input voltage: 3,000 V, pressing force: 40 t, pressing speed: 5 mm/s, The hydraulic two-column assembly and pressing press with a force of 40t OKS 1671M is designed for straightening parts, pressing in and out of sleeves, bushings, bearings, gears, as well as other pressing works during the repair of tractors, cars and agricultural machinery. The press can be used for cutting, bending, drawing and other operations. Maximum force, kN (tf) – 392(40) Maximum working pressure in the hydraulic system, MPa (kgf/cm2) – 20(200) Piston stroke, mm – 250 Piston speed during the working stroke, mm/s – 5 Maximum distance between the table and the piston, mm – 1000 Maximum table travel, mm – 750 Dimensions of clearances between the posts, mm: from front to back – 250 Fpsdpswbz Irefx Ag Dor from left to right – 1000 Dimensions of the table support plates, mm – 400х450 Working fluid – industrial oil I20A GOST 20799-75 Pump type – eccentric three-plunger Feed, l/min – 5 Nominal speed, rpm – 1500 Power consumption, kW – 3 Overall dimensions, mm – 1575х640х1970 Weight, kg – 645

Condition: used, Year of construction: 1992, functionality: fully functional, installation height: 700 mm, pressing force: 250 t, table width: 1,250 mm, table length: 1,150 mm, die cushion stroke: 150 mm, stroke length: 400 mm, Hydraulic double column press DUNKES HDS 250/10 Year of construction 1992 Technical data: Pressing force at 260 bar: 250 tons Fpodpjup Si Hjfx Ag Dor Rapid lowering speed: 365 mm/s Table clamping area approx.: 1150 x 1250 mm Ram clamping area approx.: 1150 x 1250 mm Die cushion area approx.: 800 x 1000 mm Die cushion pressing force (200 bar): 100t Die cushion stroke: 150mm Power requirement: 45 kw Installation height: 700 mm ram stroke: 400 mm Conversion of the control system to SIEMENS (in 2005) Machine height approx. 5,400 mm TP language currently Polish

Condition: like new (used), Year of construction: 2023, functionality: fully functional, pressing force: 40 t, table width: 1,500 mm, table length: 1,000 mm, reverse speed: 10 mm/s, ram plate width: 1,500 mm, ram plate length: 1,000 mm, type of input current: AC, travel distance X-axis: 1,200 mm, power: 9 kW (12.24 HP), Equipment: safety light barrier, If the press does not exactly meet your requirements, please click here to request a customized quotation tailored to your needs: HIDROBRASIL manufactures presses to your exact specifications at surprisingly competitive prices! ##### Mould opener-closer with 40 tons pressing force Table and ram size: 1500 x 1000 mm for heated tools Technical data: Pressing force: 40 tons Maximum open height: 1800 mm Ram travel: 1500 mm Oil temperature monitoring: Electric air cooling Lubrication: Manual via grease nipple Travel of the extending table: 1200 mm Speed of the extending table: 30 mm/sec. Electrically steplessly rotatable ram: 180 degrees T-slots: According to customer requirements Pressure setting: From 10 tons to 40 tons Monitor: 10" on the control cabinet for pressure setting and warning messages Two-hand operation Special features: Insulation of the clamping plates towards the ram: With resin insulation plate and special ventilation plate Hydraulic system: With BOSCHREXROTHPARKERATOS components Safety components: From SICK Control system: SIEMENS Remote maintenance unit: SECOMEA - Ethernet Installation and operating conditions: Maximum ambient temperature: 40 °C Height above floor (overall height): Approx. 3800 mm Total weight of the press without operating materials: Approx. 13 tons This machine is supplied in the colors requested by the customer and complies with all EU legal requirements and standards. ##### Are you looking for a customized machine? Fjdpetwmp Sefx Ag Djpr Contact us for a customized offer.

Condition: new, Year of construction: 2025, functionality: fully functional, Specialised press built from the ground up for briquetting of iron, steel and similar alloys. Includes integrated oil collection pads. Does not include packing table – only briquette guides (slides). Comes with see through bunker doors & oil heating elements as standard. Machines are controlled by Siemens KTP-400 touchscreens. 2nd generation available for purchase from February 2024. For this press please first contact us! Technical Data : Throughput: Up to 600 briq/h* Main motor: 30kW Infeed motors: 2.6kW Fpjdotmugcopfx Ag Der Cooling system: 1.6kW Total power: 34.2kW Oil tank: 260l Filters: 4 Length: 2000mm Width: 2000mm Height: 2200mm Weight: 3500kg Briquette size: 40-110, D80mm Warranty: 2 years / 2 000 workhours

Condition: used, Year of construction: 2021, functionality: fully functional, total height: 7,000 mm, total width: 4,750 mm, total length: 6,000 mm, pressing force: 1,000 t, reverse speed: 60 mm/s, The MV-1000E/NC-SINCRO hydraulic press is custom-designed for the adjustment of progressive dies. It features a tilting upper table and a movable lower table made of C45E steel, machined with DIN-650 T-slots to ensure minimal friction in the vertical movement of the upper table. This is achieved through the installation of maintenance-free bimetallic bushings and perfect parallelism ensured by four high-mechanical-resistance cylindrical columns of 300 mm in diameter, chrome-plated and rectified. STRUCTURE AND TABLES • Features a structure made from oxy-cut steel divided into three electro-welded monoblocks, exclusively manufactured from S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed with finite element software. • Cylindrical columns with a diameter of 300 mm, high mechanical resistance, rectified, and chrome-plated to maintain a low friction and wear coefficient. • Upper table with T-slots and anti-fall safety system. • Useful table surface: 4,750 x 2,250 mm. • Structure designed to support 600 TN of concentrated force on 1/3 of its surface. • Lower table designed to support up to 50 TN in displacement, supported by bronze guides with graphite load and mechanical positioning centers for precise table positioning. CYLINDER AND HYDRAULIC GROUP • 6 single-acting cylinders with lapped sleeves, chrome-plated pistons, and anti-wear guides. • Four 50 TN hydraulic compensators located at the ends of the lower table. • 800-liter hydraulic group with a silent Denison pump, automatic disconnection of the fast approach pre-filling speed, and equipped with a decompression system in working speed. • Proportional pressure system and optical gauges for displacement control on the upper table, with a synchro-electronic system for compensating off-center or unbalanced forces. • Hydraulic group cooling system with an independent air-oil radiator unit. • All M series hydraulic presses include a lateral pressure switch to adjust the most suitable pressure setting for each type of work. • Glycerin manometer with tonnage reading. ELECTRICAL INSTALLATION AND SAFETY • Includes a SIEMENS safety PLC model SIMATIC S7 1200 and a 12” touchscreen. Allows programming of semi-automatic and automatic operating modes, power, travel, and upper table dwell time. Capable of storing 300 recipes, with each recipe able to program all the above values. • Low voltage operation via two-hand pushbutton. • Anti-fall safety system with hydraulic safety jaws. • Level IV photoelectric barriers installed at the front and rear. • Lateral protections with opening and safety microswitches. TECHNICAL SPECIFICATIONS Power tn 125 - 1000 Opening Force tn 100 Powered Speeds 1 Engine Power kW 75 Fast Pre-Fill Speed mm/s 100 Variable Working Speed mm/s 12-4 Fpodewpgwnepfx Ag Djr Return Speed mm/s 60 Guide Diameter mm 300 Maximum Pressure Bar 290 Useful Table Area mm 4.750 x 2.200 Lower Table Displacement mm 2.200 Vertical Travel of Upper Table mm 800 Between Columns mm 5.000 x 1.490 Total Front mm 6.000 Total Side mm 4.750 Total Height mm 7.000 Weight kg 150.000

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication Fsdpfxedzp Tco Ag Dspr - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: new, Year of construction: 2025, H-FRAME DOUBLE-ACTING HYDRAULIC PRESS MODEL HDD 400 / 400 TON Ram Cylinder Capacity (ton): 400 ton Min. Working Pressure (bar): 30 bar Max. Working Pressure (bar): 250 bar Main Cylinder Diameter: Ø 420 mm * 1 pc Auxiliary Cylinder Diameter: Ø100*60 mm * 2 pcs Table Size (mm): 1500 x 1200 mm Stroke (mm): 1000 mm Fedpfxswbtn Re Ag Djpr Daylight (mm): 1400 mm Advance Speed (mm/sec): 1400 mm/sec Return Speed (mm/sec): 200 mm/sec Working Speed (mm/sec): 2–12 mm/sec Cushion Capacity (ton): 200 ton Cushion Stroke (mm): 400 mm Ejector Force (ton): 10 ton Ejector Stroke (mm): 300 mm Motor (kW): 37 kW Pump (cc): 100 cc Overall Dimensions (LxWxH): 2550 x 3500 x 6100 mm Weight (kg): Approx. 26,000 kg

Condition: excellent (used), Year of construction: 2004, Manufacturer: MULLER WEINGARDEN Model: G2-1400/630 Year: 2005 Condition: Used Stock Number: 0362 CONDITION: EXCELLENT Fpsdpfxjw Hdpcj Ag Der Press Force: 1,400 t Slide Stroke: 1,500 mm Slide Working Speed: 40 to 127 mm/s Approach Speed: 700/850 mm/s Table Dimensions: 3,500 x 2,500 mm Front Opening: 3,500 mm Lower Blank Holder Cushion Force: 400 t Lower Blank Holder Cushion Stroke: 300 mm Side Opening: 2,400 mm Lateral Movable Table: Present (side) Press Force (Secondary): 630 t Press Slide Stroke: 1,300 mm Press Table Size: 3,350 x 2,130 mm Front Opening (Press): 3,350 mm Press Slide Working Speed: 12 to 20 strokes per minute Side Opening (Press): Lateral opening present

Condition: as good as new (ex-display), Year of construction: 2020, Double column press 20 T capacity, a) Closing speed up to 10 mm/sec Fpsdpfxehmbhqs Ag Dsr b) opening speed up to 30 mm/sec c) table size between columns 1400x1100 mm d) ram size between columns 1400x1100 mm e) Manual lubrication (via grease nipple) f) UKF pump-cooling-filtration ( electrical cooling ) g) Pressure adjustment from 4 T to 20 T ( adjustable via rotary control ) h) Travel adjustable via slide control Type of construction Press design Double column press ,hydraulic Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 200 kN Free ripping force max. 20 kN Pressure build-up time Closed tool Steel on steel Max. 4 sec. Dimensions Max. Opening width 500 mm Stroke 300 mm Table height above floor, approx. 900 mm Height above floor (headroom) approx. 2800 mm Hall height min. 3,500 mm Parallel deviation at 20°C #ERROR! mm Deflection Determined at max. clamping force with 2/3 occupancy < = 0.4 mm/m Weight Total weight of the press without operating materials approx. 3 to Table cut-out Size 1100x850 mm Speeds Fast closing with 9 mm sec. Pressing speed 9 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of press/driving cylinders 2 pcs. Operating pressure max. 280 bar Pressing pressure build-up time 3-5 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH/PARKER approx. 35 L/min Oil volume approx. HLP 46 D 150 litres Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Circulation pump for cooling ACS approx. 6.5 L/min Electrical system Main supply 400 V AC Control voltage 24 V Frequency 50 Hz Hydraulic connection Main motor 3 kW Total connection Approx. 5 kW

Condition: used, Year of construction: 2020, functionality: unexamined, total height: 6,400 mm, total width: 4,500 mm, total length: 3,800 mm, operating speed: 110 mm/s, reverse speed: 180 mm/s, distance table to ram: 1,500 mm, We are offering here a new build of the machine shown. The machine was put into operation in 2020 and can be inspected by the customer. Technical data: Press force T 800 Opening force T 80 Motor power KW 55/75 + 55/75 Piston stroke 1000mm Rapid pre-fill speed mm/s 110 Working speed mm/s 6 Fsdpfxowlrv Uo Ag Dopr Return speed mm/s 180 Guide diameter mm 250 Max pressure Bar 250 Useful table area mm 3,500 x 2,000 Lower table displacement mm 2000 Between columns mm 2,000 Open height mm 1500 Total front mm 3800 Total side mm 4500 Total height mm 6400 Weight kg 134,600 The MV-800E/NC-SINCRO press was specially developed for the adjustment and testing of molds, dies, and stamps. The 4 columns with 250 mm diameter made of C45E steel were specially manufactured for high stress. It features an optimized hydraulic system with a pressure of up to 250 bar, ensuring long service life and reliability. It meets all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLE • A structure that withstands 600 T concentrated force on 1/3 of its surface. • Lower table with T-slots. • Upper table with T-slots. • Usable table surface: 3,000 x 2,000 mm. CYLINDER AND HYDRAULIC UNIT • Two double-acting hydraulic cylinders with 400 T each. • Single-stage hydraulic unit with automatic shutoff of pre-fill speed and independent operation, equipped with a decompression system and proportional pressure pre-fill valves. Equipped with digital potentiometers on the upper table for displacement control and an electronic synchronization system to compensate for off-center or unbalanced forces. • The press is equipped with a side pressure switch to regulate the most suitable pressure setting for each specific task. • Glycerin manometer with tonnage display. ELECTRICAL INSTALLATION AND SAFETY • Electrical installation for operation with 1 or 2 speeds of the main cylinder feed. • The press has a manual cycle and an automatic cycle (activated via a test button selector): • The manual cycle allows the execution of all movements (step by step) of the press at slow speed. • The automatic cycle allows the press to perform a complete production cycle. • Electrical safety system for the upper table fall protection system. • Lower table with hydraulic removal and physical stops. • The machine features a control panel with a touchscreen display for entering operating and calibration data. • 2 optical barriers of 1,000 mm with safety level IV installed at the front and rear. • Electrical components from Siemens are manufactured according to applicable CE regulations and laws in protection class IP55. • Electrical and hydraulic functions are redundant and self-controlled. Includes an additional safety block and self-monitoring devices for operation and safety. Includes inspection and certification of correct operation and safety distance for light barriers. • Safety is ensured by a laser and area protection with light barriers of level IV.

Condition: used, Machine not operational – control system not running Special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Serial No. 300487 Year of manufacture: 2006 Pressing force: 500 tons Column gap front and rear: 2520 mm Table surface: 2500 x 2500 mm Ram surface: 2500 x 2500 mm Ram stroke: 600 mm Installation height max.: 600 mm Table height above floor: approx. 900 mm Fpedpfodzqptox Ag Dor Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable approach speed: 100-800 mm/s Pressurization to 5000 kN: approx. 0.7 sec. Return speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-position flat guide for the ram - Hydraulic ram locking at TDC - Freestanding control cabinet (200 x 50 cm) - Siemens PLC control S7-314 - Operation via Siemens OP 170-B (5.7”) - Two-hand control desk, freestanding - Floor-level installation - Table plate 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication - Operating manual with circuit diagrams Required space (L x W x H): 372 x 260 x 460 cm Required space for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: as good as new (ex-display), Year of construction: 2020, Hydraulic 400 to column press suitable for continuous shift operation, with these basic data: a) Closing speed 100 - 450 mm/sec. b) Opening speed 50 - 250 mm/sec ( adjustable via touch screen ) c) Pressing speed 5 - 60 mm/sec ( adjustable via touch screen ) d) Piston accumulator with approx. 4 nitrogen bottles e) Table size (clamping surface) 2700 x 1700mm ( seen from the front, between the columns ) f) Total table size 3400 x 1700mm g) 28 T-slots according to customer requirements h) Table, ram and press head are annealed stress-free. Fedpfx Ajg Iihwsg Dspr i) column diameter 250 mm j) slide size 3400 x 1700mm (clamping surface 2700 x 1700mm ) k) Total size of the machine approx. 3900 x 2200 ( at the bottom ) x 5700 mm height l) Oil temperature monitoring ( adjustable via touch screen ) m) Automatic lubrication ( adjustable via touch screen ) n) Free positioning of the ram ( adjustable via touch screen ) o) KEYENCE light barriers 14 mm on front and rear side p) Circuit oil cooling ( adjustable via touch screen ) q) Pressure holding valve 0 to 600 sec. ( adjustable via touch screen ) r) Table top size 3400 x 1700mm, plane milled s) Laterally monitored doors, 1200mm high, 1000mm wide t) RITTAL control cabinet, 2200 mm wide, up to 20 m from the press u) Pressure setting from 50 to 400 tons ( adjustable via touch screen ) v) Travel limitation optionally via pressure or position w) Programming mode, set-up mode, single stroke + continuous stroke (adjustable via rotary switch ) x) Swivelling control panel with 15 inch touch screen monitor y) Two-hand operation on both sides z) Prepared for automatic material feed ( SIEMENS S 7 1500 ) aa) Machine body primed and painted bb) assembly, commissioning, instruction against separate charge The hydraulics of the presses we offer are completely based on BOSCH-REXROTH/Parker/HAWE components. In the switch cabinet only components are used (SIEMENS) which are easily available in Germany. The safety technology comes completely from SICK except for the light barriers. The control system is supplied by SIEMENS. ( S 7 1500 ) as well as the touch screen monitor with 15 inch. The SIEMENS remote maintenance unit SECOME -Ethernet is included in the scope of delivery. SPECIAL FEATURE: the design chosen by us with two press cylinders and the piston accumulator make it possible to supply the full power with a main motor of 90 kW. Below under 1.3 the technical details Technical data Press design Press design Column press Thermally neutral 80 - 120 °C Number of operating sides 2 sides Forces Pressing force max. 4,000 kN Free ripping force max. 600 kN Pressure build-up time Closed tool steel to steel Max. 2 sec. Dimensions - intended minimum tool height 600 mm Max. Opening width 1600 mm Stroke and min. opening 1000/600 mm Table height above floor 820 mm Height above floor (headroom) approx. 5700 mm Hall height min. 7000 mm Parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.17 mm/m Weight Total weight of the press without operating materials approx. 52 To Speeds ( see attached cycle diagram ) Fast closing 100 - 450 mm/s Pressing speed At F max.

Condition: like new (used), functionality: fully functional, machine/vehicle number: FDL-150-100E/NC, total length: 1,200 mm, pressing force: 150 t, table width: 800 mm, working height: 600 mm, clearance between the columns: 1,250 mm, Equipment: documentation/manual, safety light barrier, DOUBLE-COLUMN HYDRAULIC PRESS WITH TWO SIDE CYLINDERS FOR PRE-PRESSING AND PRESSING OF ROTORS AND STATORS, AND A CENTRAL CYLINDER FOR ROTOR SHAFT EXTRACTION, AS WELL AS FOR SHAFT EXTRACTION IN CASE OF REPAIR It features an extendable table for stacking and handling rtors and stators. Fpodpfewpg Awsx Ag Dsr It meets and satisfies all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLES • Consists of a rigid fixed bench welded structure made exclusively from S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Mechanically movable grooved table measuring 1200 x 800 mm with a stroke of 1,200 mm, equipped with a worm gear reducer and a 0.5 HP electric motor with brake. • Central drill on the table with a diameter of 250 mm and a maximum depth of 550 mm. • Useful lifting capacity of the table for moving 4 tons. • Movement speed of 30 mm/sec. • Front interior width of 1250 mm (space between columns). • Working height of 600 mm. MAIN CYLINDERS: 150 TN • Two 75-ton hydraulic cylinders (150 tons total), with a stroke of 1200 mm connected by a plate with a central hole of 250 mm in diameter. • Maximum useful height of the cylinder plate: 1,440 mm. • Minimum useful height of the cylinder plate: 200 mm. ABSTRACTION CYLINDER • One 100-ton central cylinder with a stroke of 1200 mm. • Designed to accommodate an abstraction clamp, end of the rod threaded to M 35.150 x 40 mm length. • Maximum useful height of the abstraction cylinder: 1600 mm from the root of the rod thread. • Minimum useful height of the abstraction cylinder: 400 mm from the root of the rod thread. HYDRAULIC GROUP • Two-speed hydraulic group with 5.5 HP power “Siemens Motor”, with automatic disconnection of high speed and independent speeds. Maximum pressure: 250 bar. • Pressure regulation system using proportional valves. • Air-oil cooler. • Temperature sensor. • Hydraulic group located on the right side. ELECTRICAL INSTALLATION AND SAFETY • Equipped with a SIEMENS mod. SIMATIC S7 1200 safety PLC and a 12” HMI touchscreen mod. MTP with 99 memory slots allowing adjustment of pre-pressing power, pressing, calendering, and stroke of the pressing and extraction cylinders, as well as the holding times during processes. • Electrical and hydraulic maneuvers are redundant and self-controlled. They include an additional safety block and self-control devices for operation and safety. Includes verification and certification of correct operation and safety distance for photoelectric cells. • The electrical panel includes a selector for choosing the type of work in manual, semi-automatic, or automatic position and a selector for high-speed or low-speed operation. • Operation is performed via a two-hand low-voltage electrical pushbutton. • All installed electrical materials are Siemens, including relays, contactors, main motor, etc. • Ready for Industry 4.0. • To ensure safety, it includes category IV photoelectric barriers located in the front work area, two fixed side guards, and a practicable rear guard with a magnetic disconnection detector.

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Fpsdpfew A Amrox Ag Dsr Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed - Blow-off device electrically pre-wired, without air valve - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: like new (used), Year of construction: 2019, pressure:400 t stroke:900 mm Fedefh Izmspfx Ag Djpr Table dimensions:1200 x 1200 mm Deep-Drawing Pillow:150 t travel away deep-drawing pillow:280 mm Daylight Opening:1100 mm

Condition: used, Year of construction: 2024, functionality: fully functional, total height: 2,675 mm, table height: 900 mm, total width: 1,075 mm, total length: 1,525 mm, pressing force: 100 t, table width: 700 mm, table length: 500 mm, overall weight: 2,540 kg, reverse speed: 60 mm/s, distance between side stands: 800 mm, stroke length: 250 mm, Equipment: safety light barrier, RIGID FRAME HYDRAULIC PRESSES We have engineered the motorized rigid frame hydraulic presses of the R/NC series in six different capacities ranging from 80 to 500 tons. Specially designed for stamping, die-cutting, and drawing operations. The latest generation R series hydraulic presses have evolved into highly versatile machines, including the capability to integrate seamlessly into automatic production lines. They operate at a hydraulic pressure below 320 BAR to ensure maximum durability of the entire hydraulic system. The R/NC series drawing and stamping presses feature an electro-welded frame made exclusively from S355JR steel, stabilized and precision-machined after welding for perfect parallelism and accuracy. The frame design and strength are optimized using finite element analysis software, ensuring our high standards of precision and quality are always maintained. Both the upper and lower tables are made from precision-machined C45E steel and feature DIN-650 T-slots. The upper table maintains perfect parallelism by means of four lateral cylindrical guides with maintenance-free, anti-friction bimetallic bushings. The double-acting cylinder features a lapped barrel, a chrome-plated piston, and maintenance-free wear guides. The hydraulic unit is motorized, offering two speeds with automatic disengagement of the rapid speed, and includes a cylinder decompression valve. Standard features include a SIEMENS SIMATIC S7 1200 safety PLC and a 4” MTP-400 touchscreen positioned above the electric foot pedal control. This setup allows for programming of semi-automatic and automatic operating modes, power, stroke, and dwell time of the upper cylinder. Up to 99 recipes can be stored, with full parameter settings for each recipe. Fpjdpfxjwlgkms Ag Der The electrical control panel includes a selector switch for manual/automatic operation, and a key switch for maintenance tasks. All electric and hydraulic controls are redundant and self-monitored, with an additional safety block and safety self-monitoring features. The machine includes verification and certification of correct operation, as well as the safety distance of the light curtains. Safety features include type 4 PLe photoelectric light curtains at the front working area, two fixed side guards, and a rear access guard equipped with a magnetic disconnect sensor, polycarbonate windows, and LED interior lighting. Installation of a hydraulic cushion or ejector is supported. Compliant with all essential CE safety and health requirements. Supplied with an instruction manual. Technical Specifications: - Force: 100 t - Motor power: 13 kW - Working speed: 3–9 mm/s - Approach speed: 40 mm/s - Return speed: 60 mm/s - Maximum pressure: 319 bar (up to 320 bar) - Ram stroke: 250 mm - Guide diameter: 50 mm - Lower table: 700×500 mm - Upper table: 600×450 mm - Max. vertical opening: 500 mm - Front opening: 800 mm - Working height: 900 mm - Overall front width: 1,525 mm - Overall length: 1,075 mm - Overall height: 2,675 mm - Weight: 2,540 kg

Condition: used, Year of construction: 2021, functionality: fully functional, pressing force: 500 t, Hydraulic 500 T Gantry Straightening Press with tool clamping device and parallel support for the bending blade a) Idle and pressing speed up to 17 mm/sec b) Opening speed up to 44 mm/sec c) Table size 2000 x 850 mm d) Open height 1500 mm e) Overall size approx. LWH 1500 x 3000 x 4300 mm f) Oil temperature indicator on the tank g) Lubrication via grease nipple h) Table with grid design i) Remote control j) Pressure adjustment from 80 T to 500 T via rotary dial k) Table moves hydraulically outward 700 mm for loading l) Cylinder moves left and right via racks m) Machine body powder-coated or double-coated n) T-slots according to customer requirements o) Cylinder induction-hardened p) Assembly, commissioning, and instruction are charged separately. Press type: GANTRY PRESS Thermally neutral 80 – 120 °C Number of operating sides: 3 Forces Max. press force: 5,000 kN Max. free tear-off force: 800 kN Pressure build-up time: Closed tool, steel on steel: Max. 3 seconds Dimensions Max. opening width: 1,500 mm Stroke and min. opening: 1,300 mm/200 mm Table height above floor: approx. 850 mm Fpsdjwgakvepfx Ag Dor Height above floor (overhead height): approx. 4,300 mm Hall height: min. 5,000 mm Deflection Determined at max. closing force with 70% occupancy: < = 1.2 mm/m Weight Total weight of the press without operating materials and table top: approx. 25 t Speeds Quick closing with 17 mm sec. Pressing speed at F max.

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-600E/NC, pressing force: 600 t, table width: 990 mm, table length: 890 mm, operating speed: 5 mm/s, overall weight: 23,000 kg, reverse speed: 18 mm/s, Equipment: documentation/manual, safety light barrier, The MV-600E/NC four-column hydraulic press belongs to the M/NC series and is custom-designed to achieve greater precision and capacity, specifically manufactured for stamping, deep drawing, punching, and deburring tasks. Power tn 600 Motor Power 40 HP a 440 Vca / 60hz Working Speed mm/s 5 Approach Speed mm/s 15 Return Speed mm/s 18 Piston Stroke mm 1.015 mm - (40”) Guide Diameter mm 200 Table Usable Area mm 990 x 890 x 130 (39” x 35” x 5”) Between Columns mm 990 x 370 Vertical Clearance mm 1.625 - (64”) Working Height mm 990 - (39”) Lower Hydraulic Knockout Tn 80 Lower Knockout Stroke mm 406.4 - (16”) Upper Hydraulic Knockout Tn 80 Upper Knockout Stroke mm 406.4 - (16”) Total Frontal mm 1.850 Total Lateral mm 1.700 Total Height mm 4.500 Weight Kg. 23.000 Kg. approx. Fpodpfx Aswpggisg Dsr Equipped with a top and bottom table made of C45E steel, machined with DIN-650 slots, and a removable upper counter-table of 990 x 890 x 130 mm for die holders with “T” slots. We ensure minimal friction in the vertical movement of the top table through the installation of maintenance-free bimetallic bushings, with perfect parallelism achieved by four chromed and ground cylindrical columns. It uses an optimized hydraulic system with a pressure of 320 Bar, ensuring prolonged durability and reliability in its performance. It meets and satisfies all essential safety and health requirements according to CE regulations. STRUCTURE AND TABLES • Consists of three electrowelded blocks made exclusively of S355JR steel. • Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. • Calculated and designed using finite element software. • Incorporates a SIEMENS SIMATIC S7 1200 PLC and a 7” HMI KTP-700 touch panel. This allows programming of the power, cylinder stroke, and speeds, with a storage capacity of 300 memories for different work cycles. CYLINDER AND HYDRAULIC GROUP • Double-acting cylinder with lapped sleeve, chromed piston, and maintenance-free anti-wear guides. • Motorized hydraulic group with two speeds and automatic disconnection of fast speed. High-pressure pump and 10-micron return filter. Includes cylinder decompression valve, directional valve, and safety valve. A pressure switch located on the side allows the most appropriate pressure setting for each type of work. • Glycerin manometer with reading in tons. ELECTRICAL INSTALLATION AND SAFETY • The electrical panel incorporates a selector to choose manual, semi-automatic, or automatic operation modes, and another selector for fast or slow speed operation. • Equipped with a PLC to internally assist with maneuvers and decompression time. • Operation is carried out using a low-voltage electric two-hand button panel. • Electrical and hydraulic maneuvers are redundant and self-controlled, incorporating an additional safety block and self-control devices for maneuvering and safety. Includes verification and certification of proper operation and safety distance for photocells. • For safety, category IV photoelectric barriers are incorporated in the front work area, two fixed side protections, and a movable protection with a magnetic disconnection detector at the rear. • Machine equipped with an IXON system for online communication in case of faults or reprogramming. • Ladder with upper walkway for repair access (scaffold).

Condition: like new (used), functionality: fully functional, machine/vehicle number: MV-300E/NC, total height: 3,500 mm, total width: 1,800 mm, total length: 2,300 mm, pressing force: 300 t, table width: 1,250 mm, table length: 1,250 mm, overall weight: 18,000 kg, pressure: 320 bar, Equipment: documentation/manual, safety light barrier, The MV-300E/NC four-column hydraulic press belongs to the M/NC series and is custom-designed to achieve greater precision and capacity, specifically manufactured for deep drawing, punching, and deburring tasks. Power tn 300 Motor Power kW 18 Piston Stroke mm 750 Approach Speed mm/s 110 Variable Working Speed mm/s 5-15 Return Speed mm/s 130 Guide Diameter mm 150 Maximum Pressure Bar 320 Table Usable Area mm 1.250 x 1.250 Between Columns mm 1.250 x 940 Vertical Clearance mm 1.000 Total Frontal mm 2.300 Total Lateral mm 1.800 Total Height mm 3.500 Weight kg 18.000 STRUCTURE AND TABLES Fpsdpfxswphhnj Ag Dsr Consists of three electrowelded blocks made exclusively of S355JR steel. Stabilized and machined at the end of the welding process to ensure perfect parallelism and precision. Calculated and designed using finite element software. The bottom table has a 50 Tn hydraulic cushion with a useful surface of 950 x 750 mm and three front consoles to support the die outside the press.Incorporates a SIEMENS KP-700 COMFORT NC for the regulation of the top table stroke, speed changes, and cushion regulation. CYLINDER AND HYDRAULIC GROUP 2 single-acting cylinders with lapped sleeves, chromed pistons, and maintenance-free anti-wear guides. 2 auxiliary double-acting cylinders for fast approach and return speeds. Variable speed motorized hydraulic group. Includes cylinder decompression valve. Silent hydraulic pump. All hydraulic presses of the M series include a pressure switch located on the side, allowing the most suitable pressure setting for each type of work to be regulated. Glycerin manometer with reading in tons. ELECTRICAL INSTALLATION AND SAFETY Incorporates a Siemens SIMATIC S7 1200 safety PLC and a 7” KTP-700 COMFORT touch screen located on the electrical panel. Allows programming of semi-automatic and automatic modes, power, stroke, and dwell time of the top cylinder and cushion. It has a storage capacity of 300 recipes, each recipe can program all the above values. Prepared for Industry 4.0. The electrical panel includes a selector that allows choosing the type of work to be performed in manual, semi-automatic, or automatic mode and a selector to choose operation in fast or slow speed. Electrical and hydraulic maneuvers are redundant and self-controlled. They incorporate an additional safety block and self-control devices for maneuvering and safety. Includes verification and certification of correct operation and safety distance for photocells. Operation is carried out by low voltage electric pedal. For safety, they incorporate category IV photoelectric barriers located in the front working area, two fixed side guards, and a practicable guard with a magnetic disconnection detector located at the rear.

Condition: used, functionality: fully functional, pressing force: 150 t, pressure: 250 bar, Double-column hydraulic press equipped with two side cylinders connected by a platen for the pre-pressing and pressing of rotors and stators, and a central cylinder for the extraction of the mandrel and fitting of the rotor shaft, as well as shaft removal during repair operations. Features a retractable table for stacking and handling rotors and stators. MAIN CYLINDERS 150 t Fpodpfx Aoxc Ekdsg Djr - 2 hydraulic cylinders of 75 t each, with a stroke of 750 mm, joined by a slotted platen with a central bore of 250 mm diameter. - Maximum usable height between cylinder platens: 1,300 mm. - Minimum usable height between cylinder platens: 550 mm. EXTRACTION CYLINDER - 1 central cylinder of 80 t, with a 1,200 mm stroke. - Prepared to fit an extraction clamp; rod end threaded M 35 x 1.50 pitch, 40 mm length. - Maximum usable height of extraction cylinder: 1,300 mm to the root of the rod thread. - Minimum usable height of extraction cylinder: 100 mm to the root of the rod thread. TABLE AND STRUCTURE - Mechanically movable slotted table, 1,200 x 800 mm, with a 600 mm stroke, fitted with a worm gear reducer and 0.5 HP electric motor with brake. - Central bore on the table: 250 mm diameter; max. depth 550 mm. - Effective lifting capacity of the table for movement: 4 t. - Table traverse speed: 2,600 mm/min. - Internal front width: 1,250 mm. - Working height: 600 mm. HYDRAULIC POWER UNIT - Two-speed hydraulic unit, 5.5 HP, with automatic disengagement of rapid speed and independent speeds. Maximum pressure: 250 bar. - Digital control for maximum force during pre-pressing, pressing, and fitting; digital tonnage display. Pressure adjustment system via proportional valves. - Selector for approach and measuring speeds.