Condition: new, neu ca. 4 Wochen ab Auftragse 4400 € 2400 x 1200 mm 850 mm 8000 kg 945 kg 28 mm - Fully milled table top 25 mm in S355J2+N with high degree of accuracy (+/- 0.05 mm) and rounded edges and holes - Hard chrome-plated table surface Cr75 Fpeb Hlmewiriiow Eeg The main advantage of our tables compared to conventional systems is with the hard chrome plating Cr75, that this process achieves a much deeper penetration into the base material of up to 0.07 mm and the hardness of the surface reaches up to HV750. This also ensures optimum and lasting anti-spatter adhesion on the surface, which is one of the most efficient on the market. - Exact dimensional and fitting accuracy of the tools with 28 mm perforation (compatible with comparable premium suppliers) - Grid lines 100 x 100 mm - 4 solid table feet withload capacity 2 ton/feet and levelling option - Different foot variants available (standard, height-adjustable and with castors) - Load capacity 8 to - All-round 200 mm high side cheeks with diagonal perforation - 2-sided millimetre scaling - Substructure with stiffeners

Condition: new, neu ca. 6-8 Wochen ab Auftrag 6400 € 132.48 € 3000 x 1500 mm 850 mm 8000 kg 1544 kg 200 mm 28 mm - Fully milled table top 25 mm in S355J2+N with high degree of accuracy (+/- 0.05 mm) and rounded edges and holes - Hard chrome-plated table surface Cr75 The main advantage of our tables compared to conventional systems is with the hard chrome plating Cr75, that this process achieves a much deeper penetration into the base material of up to 0.07 mm and the hardness of the surface reaches up to HV750. This also ensures optimum and lasting anti-spatter adhesion on the surface, which is one of the most efficient on the market. - Exact dimensional and fitting accuracy of the tools with 28 mm perforation (compatible with comparable premium suppliers) - Grid lines 100 x 100 mm - 4 solid table feet withload capacity 2 ton/feet and levelling option - Different foot variants available (standard, height-adjustable and with castors) - Load capacity 8 to - All-round 200 mm high side cheeks with diagonal perforation - 2-sided millimetre scaling Fpeb Hlmwowirice Eog - Substructure with stiffeners

Condition: new, neu ca. 6 Monate ab Auftragse Taiwan 47240 € 958.97 € 610 mm 600 mm 610 x 305 mm 300 x 600 mm 650 mm 700 mm 5 - 25 m/min 1.100 mm/min 1 - 12 mm 370 mm 1.5 kW 0.004 kW 0.19 kW 7,4 kW 2670 mm 1810 mm 2050 mm 2100 kg 355 x 50 x 127 mm 1.450 U/min 3,7 kW 4 mm 0,02 mm 0,2 mm 0,002 mm control panel on swiveling arm aut. vertical feed hardened slide ways in all 3 axes with needle rollers grinding wheel spindle on 4 high precision angular contact bearings electro-magnetic chuck Fsb Hlmowirh Sjw Eepg coolant equiptment with aut. paper filter and magnetic separator manual extractor with diamond grinding wheel grinding wheel flange grinding wheel balancing scale balance arbor LED machine lamp machine and equipment according to the CE-regulations user manual in GERMAN and ENGLISH

Condition: new, Year of construction: 2025, neu 2025 050068 Taiwan 37810 € 767.54 € 457 mm 450 mm 457 x 203 mm 200 x 450 mm 500 mm 530 mm 5 - 25 m/min 960 mm/min 0,4 - 6 mm 230 mm 0,002 - 0,04 mm/min 2850 1/min 1,5 kW 0.75 kW 0.04 kW 0.19 kW 3,7 kW 2200 mm 1575 mm 1950 mm 1854 x 1549 x 2210 mm 1320 kg 215 kg 250 kg 203 x 12,7 x 31,75 mm control panel on swiveling arm aut. vertical feed grinding wheel spindle on 4 high precision angular contact bearings electro-magnetic chuck coolant equiptment 34 lt with magnetic separator and dust exhaust manual dresser with diamond grinding wheel grinding wheel flange Fsb Hswirh Eelmw Eopg grinding wheel balancing scale balance arbor LED machine lamp machine and equipment according to the CE-regulations user manual in GERMAN and ENGLISH

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 45100 € 915.53 € Doppelsäulenführung 5200x34x1,1 mm 20-100 m/min 360 mm 360 mm 610x360 mm rund 360 mm, quadrat 360 rund 360 mm, quadrat 360 rund 325 mm, quadrat 265 735 mm 1.5 kW 3 kW 0.12 kW 2850 mm 2250 mm 1870 mm 2400 kg NC control double column band saw on linear guidelines 3° cutting angle blade brush control panel hydraulic feeding vice hydraulic vice hydromechanical blade tensioning inverter optical height adjustment proximity switch for sensing blade slippage material limit shaft pressure adjustment coolant pump Fpob Hlmwswirhxs Eeg saw blade security switch user manual in GERMAN or ENGLISH OPTIONS: hydraulic top clamping micro coolant equipment laser cutting line ALTERNATIVE: model BMSO 360 CGS NC (with servo instead of hyraulic feed) € 50.900,--

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 34400 € 698.32 € Doppelsäulenführung 4380x34x1,1 mm 20-100 m/min 325 mm 325 mm 400x325 mm rund 325 mm, quadrat 325 rund 300 mm, quadrat 265 rund 190 mm, quadrat 190 655 mm 1.1 kW 2.2 kW 0.12 kW 2130 mm 2150 mm 1650 mm 1860 kg NC control double column band saw on linear guidelines 3° cutting angle blade brush control panel hydraulic feeding vice hydraulic vice hydromechanical blade tensioning inverter optical height adjustment proximity switch for sensing blade slippage material limit shaft pressure adjustment coolant pump saw blade security switch user manual in GERMAN or ENGLISH Fpsb Hlmwowirhro Eog OPTIONS: hydraulic top clamping micro coolant equipment laser cutting line ALTERNATIVE: model BMSO 325 CGS NC (with servo instead of hyraulic feed) € 38.900,--

Condition: new, neu ca. 12 - 14 Wochen ab Auf Türkei 27500 € 558.25 € Schwenkrahmen 3660x27x0,9 mm 20-100 m/min 320 mm 320 mm 350x320 mm rund 160 mm, quadrat 150 rund 260 mm, quadrat 180 rund 300 mm, quadrat 250 740 mm 1.1 kW 2.2 kW 0.12 kW 2100 mm 2200 mm 1500 mm 1660 kg blade brush NC control panel Fjb Howirhljlmw Eepg hydraulic vice hydromechanical blade tension inverter coolant pump saw blade security switch gearbox height adjustment user manual in GERMAN or ENGLISH OPTION: hydraulic blade tentioning

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 11100 € 227.55 € Schwenkrahmen 3660x27x0,9 mm 20-100 m/min 320 mm 300 mm 320x300 mm 640 mm 0.37 kW 2.2 kW 0.12 kW 1900 mm 850 mm 1300 mm 770 kg Roller material feed with manual adjustable length stop with limit switch blade brush control panel height adjustment bar with limit switch hydromechanical blade tension inverter hydraulic vice coolant pump saw blade security switch 1,2 meter roller table Feb Hlmowirhfsw Espg users manual in GERMAN or ENGLISCH

Condition: new, neu ca. 6-8 Wochen ab Auftrag 1190 € 1000 x 1000 mm 850 mm 450 kg Fpob Hlewirg Usmw Eeg 25 mm 28 mm - Fully milled table top 25 mm in S355J2+N with high degree of accuracy (+/- 0.05 mm) and rounded edges and holes - Hard chrome-plated table surface Cr75 The main advantage of our tables compared to conventional systems is with the hard chrome plating Cr75, that this process achieves a much deeper penetration into the base material of up to 0.07 mm and the hardness of the surface reaches up to HV750. This also ensures optimum and lasting anti-spatter adhesion on the surface, which is one of the most efficient on the market. - Exact dimensional and fitting accuracy of the tools with 28 mm perforation (compatible with comparable premium suppliers) - Grid lines 100 x 100 mm - 4 solid table feet with levelling option - Different foot variants available (standard, height-adjustable and with castors) - Load capacity 500 kg/m²

Condition: new, neu ca. 6-8 Wochen ab Auftrag 1490 € 1500 x 1000 mm 850 mm 344 kg 28 mm - Fully milled table top 25 mm in S355J2+N with high degree of accuracy (+/- 0.05 mm) and rounded edges and holes - Hard chrome-plated table surface Cr75 The main advantage of our tables compared to conventional systems is with the hard chrome plating Cr75, that this process achieves a much deeper penetration into the base material of up to 0.07 mm and the hardness of the surface reaches up to HV750. This also ensures optimum and lasting anti-spatter adhesion on the surface, which is one of the most efficient on the market. - Exact dimensional and fitting accuracy of the tools with 28 mm perforation (compatible with comparable premium suppliers) - Grid lines 100 x 100 mm Fsb Hlmwswirg Is Espg - 4 solid table feet with levelling option - Different foot variants available (standard, height-adjustable and with castors) - Load capacity 500 kg/m²

Condition: used, Year of construction: 2023, gebraucht 2023 9670 prompt, Zwischenverkauf v Türkei 14900 € 1 60 mm 177 mm 3 3.7 kW 6 m/min 70x10 mm / 600 mm; 30x10 90x25 mm / 500 mm; 50x5 m 40x40 mm / 500 mm; 20x20 Ø. 40 mm / 500 mm; Ø 20 m Ø 60x2 mm / 600 mm; Ø 20x 80x40x3 mm 60x60x4 mm Fsb Hlmwewirgzj Eopg 50x5 mm / 1.000 mm; 30x4 50x5 mm / 500 mm; 30x3 mm 1160 mm 1000 mm 1175 mm 1194 kg demo machine / mint condition net price 3 driven rolls strong welded steel construction lower rolls hydr. adjustable digital read-out for lower rollspositions on seperate control panel plane and hardened universal rolls lateral rolls adjustablein 3 axes manual/hydr. horizontal and vertical operation for- and backward drive machine and equipment accordingto the CE regulations user manual in GERMAN and ENGLISH WE HAVE MORE THAN 235 REFERENCES!

Condition: new, neu ca. 4 Monate ab Auftragse Türkei 22700 € 465.35 € Doppelsäulenführung 4800x34x1,1 mm 20-100 m/min 380 mm 380 mm 430x380 mm 590 mm 0.55 kW 3 kW 0.12 kW 2900 mm 950 mm 1660 mm 1342 kg blade brush control panel hydraulic vice optical adjustment switch hydromechanical blade tension inverter mechanic top clamping material limit shaft coolant pump saw blade security switch gearbox pressure adjustment Fpeb Hlmjwirgujw Eog 1,2 meter roller table user manual in GERMAN or ENGLISH

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 202100 € 3869.08 € 320 to 6050 mm Y1 / Y2 / X und R Achse 365 mm 5100 mm 450 mm 630 mm hydraulisch 160 mm/s 10 mm/s 160 mm/s 650 mm 500 mm/s 250 mm 1100 mm 154 mm 160 l 2 x 11 kW 7500 mm 1910 mm 3350 mm 29000 kg 1 SERVO MOTOR AND PUMP PER CYLINDER 4 axes (Y1, Y2,X andR) CNC control SKY 22 - intuitive touch-screen control (simple drawing of the bending outline with your finger) 21,5“ in full HD - with 2D and 3D working screen - direct programming of the bending angle - user friendly programming in dialogue form optionally in 2D or 3D mode - 2D and 3D simulation of the bending sequence - automatic tool selection in 3D mode - automatic calculation of the blank sheet size - bending order calculation - graphic product and tool memory - correction possibility - USB and Ethernet interfaces for import, backup and programm transportation - OS: Windows 10 - IGES, STEP, DXF files import servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guided sheet support arms according to CE rules oilfilling users manual in English or German ADVANTAGES OF THIS CONCEPT: - hydraulic works only while upper beam movement - low energy consumption Fpsb Hlmwswirgns Eeg - low noise level - high speed PRICE FCA TURKEY optional equipment: CNC Control Delem DA-66 S CNC control DELEM DA-69S 3D incl. PC software Profile-S with 3D file import option

Condition: new, neu ca. 4 Monate ab Auftragse Bulgarien 102960 € 2048.9 € 800 mm 2000 mm 400 mm 260 mm 560 mm 560 mm 318 M 12 8 - 400 1/min 2 0.039 - mm/U 0.02 - 7.5 mm/U 76 0.5 - 0 mm 60 - 1/5 Gänge/" 0.125 - 37.5 240 - 4/5 410 mm 0 mm 105 mm 6 MK 225 mm 11 kW 6000 kg Their main purpose is to process pipes. Accordingly, this type of machines is widely used in the oil industry. Oil country lathes have large capabilities of processing inner and outer cylindrical and conical threads on pipes with large diameters. The clamping of the pipes with two universals and stands allows the processing of long pipes. These lathes are suitable for producing elements and equipment for the oil industry, as well as for maintaining such facilities. Febowirghs Hlmw Eopg Drive via gearbox Electrodynamic brake 3-axis digital display Fagor Quick-change tool holder Amestra type C, system like Multifix including 4 holders (3x rectangular, 1 round) 2 pcs. 3-jaw chuck Bison 3295 Dm. 500 mm on both sides of the spindle, gripping range 120-350 mm. Option: hard top jaws with gripping range 120-500 mm 2 pcs. steady rests on supports Dm. 60 - 260 mm with rollers Rapid traverses (4) Longitudinal stop for one position Taper turning device Coolant device Full length rear splash guard Lead and feed spindle cover Lathe chuck protection Tool holder protection Leveling bolts and plates Tailstock Reducing sleeve for the tailstock sleeve Mechanical movement of the tailstock with handwheel Low voltage machine light Operating instructions Equipment according to "CE" regulations Further models with spindle bore from 5 to 358 mm, centre distances from 1000 to 6000 mm and with turning diameters from 730 to 1020 mm are available on request.

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 19100 € 391.55 € 55 to 500 mm 5 40/10 bzw. 20/20 mm 20 mm 37 1/min 300x15 / 200x20 mm 10x42x90 mm 5 kW 2100 mm 1160 mm 2090 mm 1750 kg 2 foot pedals for independent work at 2 stations hydr. drive flat bar shear angle bar shear with minimum deformation by diagonal moving of the blade round and square bar shear rectangular notching unit punching unit up to diam. 40 mm fast hydraulic, Ankörnvorrichtung oilfilling table at the punching station with gauge table at the notching unit with gauge table at the flat bar shear user manual in GERMAN and ENGLISH Fpsb Hlmwowirgbs Esg OPTION: Kit € 930,00 length stop 1000 mm with contact switch, for angle, flat or bar station magnetic machine lamp 10 set round punches and dies: 8, 10, 12, 14, 16, 18, 20, 22, 24 and 26 mm

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 23600 € Fpob Hjwirf Relmw Eog 483.8 € 80 to 750 mm 40x14 mm 40 1/min 9 kW 1700 mm 1300 mm 2050 mm 1715 kg hydraulic drive table with gauge user manual in GERMAN and ENGLISH CNC options on request We have a big stock of punches and dies for immediate dispatch WE HAVE MORE THAN 700 REFERENCES!

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 17300 € 354.65 € 80 to 510 mm Feb Howirf Dslmw Ejpg 40x14 mm 40 1/min 9 kW 1700 mm 1300 mm 2050 mm 1715 kg hydraulic drive table with gauge user manual in GERMAN and ENGLISH CNC options on request We have a big stock of punches and dies for immediate dispatch WE HAVE MORE THAN 700 REFERENCES!

Condition: new, neu ca. 8 Wochen ab Auftragse Spanien 16600 € 340.3 € 55 to 750 mm 40x10 mm 37 1/min 5 kW 1930 mm Fpjb Hlmwowirfwo Ejg 1200 mm 1800 mm 1885 kg hydr. drive Support table with stop Operating instructions in GERMAN and ENGLISH CNC options on request We have an extensive stock of punches and dies at your immediate disposal. WE HAVE MORE THAN 700 REFERENCES!

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 123720 € 2462.03 € 320 to 4050 mm Y1 / Y2 / X Achse 365 mm 3600 mm 450 mm 630 mm hydraulisch 160 mm/s 10 mm/s 140 mm/s 500 mm/s 350 mm/s 250 mm 900 mm 154 mm 250 l 18.5 kW 5250 mm 1770 mm 2850 mm 20000 kg Standard accessories: 3 axes (Y1, Y2,X) CNC control DT-15 - 2D grafic display 15" - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) Fpobswirfqs Hlmw Esg laser safety device Fiessler AKASmounted on the upper beam linear guided sheet support arms according to CE rules oilfilling users manual in English or German ADVANTAGES OF AD-S COMPAIRED TO PBF: - more stroke, installation height and throat - higher approach and retraction speed of the top beam - higher backgauge speed - backgauge finger on double instead of single linear guide - more options available such as: additional backgauge axes (e.g. Z1/Z2, Delta X, up to 6 axes), bending aids, laser angle measuring system, tandem design, other CNC controls ... optional equipment: R-Axis R/Z1/Z2-Axis DBend, 3D CAD/CAM importing- and simulation program (step, iges and dxf file import) CNC Control SKY22 CNC Control Delem DA66 S CNC Control DELEM DA-69S 3D incl. PC software Profile-S with 3D file import option

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 171300 € 3374.61 € 400 to 4050 mm Y1 / Y2 / X Achse 365 mm 3400 mm 510 mm 630 mm hydraulisch 160 mm/s 10 mm/s 140 mm/s 500 mm/s 350 mm/s 250 mm 1050 mm 154 mm 250 l 37 kW 5750 mm 2110 mm 3640 mm 27760 kg 3 axes (Y1, Y2,X) CNC control DT-15 - 2D grafic display 15" - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides CNC crowning table upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guided sheet support arms according to CE rules oilfilling users manual in English or German ADVANTAGES OF AD-S COMPAIRED TO PBF: - more stroke, installation height and throat - higher approach and retraction speed of the top beam - higher backgauge speed - backgauge finger on double instead of single linear guide - more options available such as: additional backgauge axes (e.g. Z1/Z2, Delta X, up to 6 axes), bending aids, laser angle measuring system, tandem design, other CNC controls ... PRICE FCA TURKEY Fpebjwirfks Hlmw Esg optional equipment: R-Axis R/Z1/Z2-Axis DBend, 3D CAD/CAM importing- and simulation program (step, iges and dxf file import) CNC Control SKY22 CNC Control Delem DA66 S CNC Control DELEM DA-69S 3D incl. PC software Profile-S with 3D file import option

Condition: used, Year of construction: 1999, gebraucht 1999 6173 Deutschland 11900 € Fpeb Hlmowirfdsw Esg 1 10700 € 500 mm 2800 U/Min Rund 180 mm, Quadratprofi Rund 120 mm, Quadratprofi 1100 mm 1450 mm 1350 mm 490 kg hydropneumatic saw feed new HM saw blade pneumatic material clamping device vertical automatically opening protective cover Discharge roller conveyor with stop and measuring system, display E 110, 1/10mm, 4.5 m long, plastic rollers b = 250 x Ø 50mm, pneum. clamping, handwheel drive and locking in the operator area, stop can be folded up user manual in GERMAN COMPLY WITH THE CURRENT INDUSTRIAL SAFETY REGULATIONS (AMVO & UVV)

Condition: new, neu ca. 10 Wochen ab Auftrags Türkei 52400 € 1053.24 € 60 to 1250 mm 3 (Y1, Y2, X) 265 mm 1050 mm 450 mm 530 mm hydraulisch 200 mm/s 10 mm/s 110 mm/s 650 mm 500 mm/s 900 mm 104 mm 100 l 7.5 kW 2300 mm 1550 mm 2850 mm 4700 kg Standard accessories: Fpsb Hlewird Tomw Esg 3 axes (Y1, Y2,X ) CNC control DT-15 - 2D grafic display 15" - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of the bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB servo motorized back gauge on linear guides and ball screws back gauge finger blocks on double linear guides upper tool 1010 / A / 75 °, devidedand cranked 4-V die block 60x60 2009 (V = 16,22,35 and 50 mm) laser safety device Fiessler AKASmounted on the upper beam linear guided sheet support arms according to CE rules oilfilling users manual in English or German ADVANTAGES OF AD-S COMPAIRED TO PBF: - more stroke, installation height and throat - higher approach and retraction speed of the top beam - higher backgauge speed - backgauge finger on double instead of single linear guide - more options available such as: additional backgauge axes (e.g. Z1/Z2, Delta X, up to 6 axes), bending aids, laser angle measuring system, tandem design, other CNC controls ... optional equipment: R-Axis R/Z1/Z2-Axis DBend, 3D CAD/CAM importing- and simulation program (step, iges and dxf file import) CNC Control SKY22 CNC Control Delem DA66 S CNC Control DELEM DA-69S 3D incl. PC software Profile-S with 3D file import option Quick Release Clamping

Condition: new, neu ca. 12 - 14 Wochen ab Auf Türkei 76820 € 1544.08 € 160 to 4050 mm Y1 / Y2 und X Achse 200 mm 3600 mm 300 mm 430 mm hydraulisch 160 mm/s 10 mm/s 140 mm/s 620 mm 250 mm/s 858 mm 104 mm 15 kW 4850 mm 1900 mm 2610 mm 10500 kg 3 axes (Y1, Y2, and X axis) CNC control DT-10 - intuitive touch-screen control (simple drawing of the bending outline with your finger) - user friendly programming in dialogue form - automatic calculation of bending sequence - automatic calculation of the blank sheet size - graphic product and tool memory - correction possibility Fsb Hlswird Hsmw Espg - USB interfaces for backup and programm transportation - PC software, generating programms on the PC and transfer to the machine by USB CNC controlled back gauge with linear guide and ball screw spindles CNC crowning table intermediate clamps for upper tool upper tool1010/A/75°/0,8, sectioned,bending radius hardened and ground die holder for 60 mm dies die type2009/85°(V 16, 22, 35, 50 mm)sectioned, geteilt, bending radiihardened and ground laser safety device Fiessler AKASmounted on the upper beam sheet support arms protection covers on the sides andback side according to CE rules oilfilling users manual in GERMAN orENGLISH ADVANTGES OF PBF SERIES: - compact structure - low cost due to serial production of standardised models without restrictions in quality and accuracy OPTION: CNC controlled R-axis (adjustment range in X = 500 mm) DBend, 3D CAD/CAM importing- and simulation program (step, iges and dxf file import) WE HAVE MORE THAN 600 REFERENCES! (sample photo)

Condition: new, neu ca. 6 Monate ab Auftragse Taiwan 20800 € 426.4 € 42 mm MK 4 280 - 1.100 mm 44 - 1.500 (12) U/min Stahl: M 25; Guss: M 38 1880 mm Feb Hlmwjwirdyo Espg 870 mm 2210 mm 1800 kg 470 - 1.270 mm 0,05 - 0,15 (3) mm/min 2.2 kW 260 mm 280 mm 1.725 x 715 x 180 mm 635 x 520 x 415 mm 2530 mm left/right rotation automatic feed drilling depth limit manual headstock adjustment with mechanical clamping electric height adjustment of extension arm and mechanical clamping mechanical clamping of swivel movement of extension arm central operation panel on the front side power load readout for drilling spindle hand wheel for spindle fine feed coolant equipment machine lamp box table machine and equipment according to the CE-regulations operating manual in GERMAN and ENGLISH

Condition: used, Year of construction: 2020, gebraucht 2020 1658 prompt, Zwischenverkauf v Bulgarien 26500 € 1 400 mm 1000 mm Fsb Hlmjwirdtjw Ejpg 200 mm 52 mm 235 mm 320 mm 6 6 M 12 50-2.240 1/min 80 0.015 - 0.6 mm/U 0.0075 - 0.3 mm/U 40 0.25 - 7.5 mm 120 - 4 Gänge/" 0.0625 - 1.875 235 mm 110 mm 50 mm 4 MK 100 mm 4 kW 2750 mm 1100 mm 1600 mm 1540 kg driven by manual transmission 3-axes digital readout Fagor 40i quick change toolpostMultifix Type Bwith4 holders (3 square, 1 round) 3-jaw chuck Bison 3204/DIN6350, Ø 200 mm spindle noseNr. 6 DIN 55027 four way rapid traverse device spindle dead center coolant equipment 1 pce. flange plate for lathe chuckØ 200 mm 1 adapter sleeve full length rear splash guard leadscrew and shaft protection safety guard for the chuck toolholder guard levelling bolts and plates quick release tailstock low voltage machine lamp operating manual machine according to "CE"