Used Manual Lathe for sale (19,579)

Condition: used, Year of construction: 2024, XYZ 1530VS x 730mm Gap Bed Manual Lathe with DRO, Swing Over Bed 390mm, Swing in Gap 610mm, Spindle Speed 20-2500rpm, Spindle Bore 54mm, Tailstock. Serial No. 11388443 (2024) Njdpjzgfb Rofx Alnecu Location: These lots are located in Rhayader, Wales, UK.

Condition: used, Year of construction: 2024, XYZ 1550VS x 1230mm Gap Bed Manual Lathe with DRO, Swing Over Bed 390mm, Swing in Gap 610mm, Spindle Speed 20-2500rpm, Spindle Bore 54mm, Tailstock. Serial No. 11308450 (2024) Location: These lots are located in Rhayader, Wales, UK. Unfortunately, there are no loading facilities on-site, dismantling and loading will be at the cost of the purchaser. All/Any tooling is being offered as specifically described. Ncjdpfxjzgdz Ao Alnou

Condition: used, L + Z Lathe WEILER Model Praktikant 800R Machine No. 3309 Year of manufacture: 1984 Centers distance: 800 mm Swing over bed: 280 mm Swing over cross slide: 160 mm Center height over bed: 140 mm Center height over cross slide: 80 mm Spindle bore: 36 mm Feeds: longitudinal and cross Chuck mounting: Short taper DIN 55027 size 5, 4x M10 Tailstock taper: MT 3 Tailstock quill travel: 90 mm Spindle speed: 42 – 2000 rpm Drive power: 1 / 1.6 kW Electrical connection: 380 Volt, 50 Hz - Spindle speed via 2 motor speeds and 8 gear steps - 3-jaw scroll chuck BILSING Ø 160 mm with 1 set of stepped jaws and 1 set of soft jaws - MULTIFIX quick-change toolpost size A with 3 exchangeable toolholders - Live center - Emergency stop Ncjdpfx Aoyg Rfijlnju - Folding chuck guard - Coolant system - Operating manual with electrical schematic - Very low operating hours Required space (L x W x H): 1900 x 700 x 1300 mm Weight: 600 kg Very good condition

Condition: used, L + Z Lathe VOEST ALPINE - WEILER Type DA 210 / 1 Machine No. 1-004/2581 Year of manufacture: 1984 Centre distance: 1000 mm Swing over bed: 420 mm Centre height over bed: 210 mm Swing over cross slide: 240 mm Centre height over cross slide: 120 mm Spindle bore: 52 mm Spindle speed: 33 - 1500 rpm, 12 steps Chuck flange: short taper DIN 55027 size 6, 4x M12 Tailstock taper: MT 4 Motor power: 5.5 kW Electrical connection: 380 Volt, 50 Hz - Spindle speeds via 12-step gearbox - 3-jaw scroll chuck AROWA Ø 200 mm (only one set of chuck jaws) - Multifix quick-change tool post, size B, with 3 tool holders - Automatic longitudinal and cross feed - Coolant system - Spindle brake - Emergency stop - Splash guard - Fixed steady rest Ø 160 mm - Machine lamp - Operating manual Space requirement (L x W x H): 2200 x 1200 x 1450 mm Njdpfxoyah Rvj Alnecu Weight: 1500 kg In very good condition

Condition: used, L + Z Lathe WEILER Type Praktikant 800R Njdjyr R Dcspfx Alnocu Machine No. 3315 Year of manufacture: 1984 Center distance: 800 mm Swing over bed: 280 mm Swing over cross slide: 160 mm Center height over bed: 140 mm Center height over cross slide: 80 mm Spindle bore: 36 mm Feeds: longitudinal and face Chuck mount: short taper DIN 55027 size 5, 4x M10 Tailstock taper: MK 3 Quill travel: 90 mm Spindle speed: 42 - 2000 rpm Drive power: 1 / 1.6 kW Electrical connection: 380 Volt, 50 Hz - Spindle speed via 2 motor speeds and 8 gearbox steps - 3-jaw scroll chuck RÖHM ZS Ø 160 mm with 1 set of stepped jaws - MULTIFIX quick-change tool post size A with 3 tool holders - Emergency stop - Hinged chuck guard - Operating manual with electrical diagram Required space (L x W x H): 1900 x 700 x 1300 mm Weight: 560 kg Good condition

Condition: used, L + Z Lathe VOEST ALPINE - WEILER Type DA 210 / 1 Nodpfjykca Hjx Alnecu Machine No. 1-004/2552 Year of manufacture: 1983 Centre distance: 1000 mm Swing over bed: 420 mm Centre height over bed: 210 mm Swing over cross slide: 240 mm Centre height over cross slide: 120 mm Spindle bore: 52 mm Spindle speed: 33 - 1500 rpm, 12 steps Chuck flange: short taper DIN 55027 size 6, 4x M12 Tailstock taper: MK 4 Motor power: 5.5 kW Power supply: 380 Volt, 50 Hz - Spindle speed via 12 gearbox steps - EMCO 3-jaw scroll chuck Ø 200 mm with turning and boring jaws - Multifix size B quick-change tool post with 3 change cartridges - Automatic longitudinal and face feed - Coolant system - Spindle brake - Emergency stop - Machine lamp - Operating manual Space requirement (L x W x H): 2200 x 1200 x 1450 mm Weight: 1400 kg Very good condition

Condition: like new (used), DN Solutions PUMA DNT2600L 2024 Model – Only 32 Cutting Hours (Like New Condition) Chuck: 12 inch Max Turning Diameter: 460 mm Max Turning Length: 1078 mm Spindle Bore: 81 mm Spindle Speed: 3,500 rpm Main Motor Power: 26 kW Max Torque: 735 Nm X-Axis Travel: 260 mm Z-Axis Travel: 1100 mm Rapid Traverse: X 24 m/min – Z 30 m/min Turret: 12 Stations Guideway System: Box Guideway Machine Weight: 4,900 kg Condition: 2024 model, only 32 cutting hours, almost in brand-new condition. Ncodpfsy D E Risx Alnou

Condition: like new (used), Year of construction: 2011, functionality: fully functional, turning diameter over cross slide: 355 mm, spindle bore: 85 mm, turning diameter over bed slide: 560 mm, center height: 280 mm, turning length: 2,000 mm, spindle speed (max.): 1,600 rpm, spindle speed (min.): 25 rpm, Turning diameter in gap: 785 mm, Huvema HU560 x 2000 Gap Bed Centre Lathe Year 2011 , CE Rated Spindle Speeds 25-1600rpm Distance Between Centres 2000mm Swing Over Bed 560mm Swing Over Cross Slide 355mm Tail Stock MT5 2 Axis Newall DRO Quick Change Tool Holder With Holders Ncjdpfx Ajzfguislnju D1-8 Camlock Chucks Excellent Condition Interlocked Guards Work Light & Coolant System Machine Comes With: 3 Jaw Chuck & Reverse Jaws - 300mm 6 Jaw Chuck - 300mm 4 Jaw chuck - 400mm Faceplate - 450mm Fixed Steady x 2 Travelling steady Fully Serviced And Ready For Production

Condition: good (used), Different tool holders . As we informed, they are used on Biglia CNC lathe. Ncedoy Shyiepfx Alnju

Condition: good (used), Toolholders bought in company where used for Biglia machine Nsdpfeyuyhisx Alnscu

Condition: new, Year of construction: 2025, turning diameter over cross slide: 250 mm, turning length: 730 mm, turning diameter: 500 mm, spindle speed (max.): 1,800 rpm, CNC lathe machine CK 6150 with flat bed We offer a new CNC lathe machine model CK6150. We use this machine in our production and you can see it in operation before ordering. The CK 6150 lathe has a flat bed and hardening guides, which ensures a long period of operation of the equipment. The machine is equipped with a CNC system, the GSK CNC system is installed as standard. Optionally, the machine can be equipped with a Fanuc or Siemens CNC system. The machine can have a tool holder for 4-6 or 8 tools, depending on the customer's wishes. It is possible to install a hydraulic chuck on the machine, which will greatly simplify the process of installing parts on it and a hydraulic tailstock. The CK 6150 lathe can be equipped with additional supporting frame for more accurate manufacturing of long parts. Technical specifications: Model CK 6150 x 1000 Maximum workpiece diameter over bed 500 mm Maximum workpiece diameter over support 250 mm Maximum workpiece length 1000 mm Maximum turning length 730 mm Spindle bore diameter 82 mm Spindle speed 150-1800 rpm Ncjdpfoxdmgvox Alnou Engine power 7.5 kW Mechanical chuck (hydraulic optional) Chuck size 250 mm. 4-position tool holder (6 or 8 optional) Maximum tool size for tool holder 25x25 mm Machine weight 2700 kg Machine dimensions 2650×1700×1820 mm We can also supply lathes CK 6140, CK 6150 and CK 6160 with other dimensions of the working part: CK 6140 dimensions of the working part 550/750 mm CK 6150 dimensions of the working part 1000/1500/2000 mm CK 6160 dimensions of the working part 1000/1500/2000 mm CK 6152E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6165E dimensions of the working part 1000/1500/2000/3000 mm CK 6185E dimensions of the working part 1000/1500/2000/3000/4000 mm CK 61100E dimensions of the working part 1000/1500/2000/3000 mm CK 61125E dimensions of the working part 1000/1500/2000/3000 mm

Condition: used, Year of construction: 2012, functionality: fully functional, machine/vehicle number: G3169-0110, turning length: 530 mm, turning diameter: 420 mm, spindle speed (min.): 20 rpm, spindle speed (max.): 4,000 rpm, spindle bore: 65 mm, travel distance X-axis: 220 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 550 mm, overall weight: 4,700 kg, turning diameter over bed slide: 800 mm, HYUNDAI WIA L200SY CNC TURNING CENTER Year: 2012 | Fanuc 18i-TB CNC Control SN: G3169-0110 • 5-Axis CNC Turning Center – Hyundai WIA L200SY • Main Chuck: 8″ | Sub Spindle: 5″ • Live Tooling & Y-Axis + C-Axis indexing • Max Turning Diameter: approx. 419–420 mm / 16.5″ • Max Turning Length: approx. 520–530 mm / ~20.5–20.9″ • Swing Over Bed: approx. 800 mm / 31.5″ • X Travel: approx. 220 mm / 8.7″ • Z Travel: approx. 550 mm / 21.7″ • Y Travel: approx. 80 mm / 3.1″ • Max Spindle Speed: up to 4,000 rpm • Main Spindle Power: ~20 HP (~15 kW) • Sub Spindle Speed up to 6,000 rpm • C-Axis indexing: 0.001° possible • Tool Stations: approx. 12 • Coolant system and chip conveyor included • Approx. Dimensions: 120″ × 68″ × 80″ Nedpfex I A Hcsx Alnecu • Approx. Weight: ~10,500 lbs (~4,760 kg) NOTE: MACHINE WAS REMOVED FROM GOOD WORKING CONDITION 2 YEARS AGO. PLANNED TO PUT BACK IN SERVICE BUT SELLER WILL NO LONGER BE DOING MACHINING.

Condition: excellent (used), Model: 4M/65E Condition: Very good Dimensions: 80.00 (H) x 60.00 (W) x 120.00 (L) inches Ncjdexz Tfaspfx Alnsu Additional Description: - Automatic copy lathe - To make spades, shovels, curling's, gun holders, axes, legs, cricket bats and so on. - Makes 4 pieces at the same time. - Router (no sanding attachment) - Speed regulation on slide. - Works great

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 020033, spindle speed (max.): 5,000 rpm, spindle diameter: 110 mm, controller model: Siemens SINUMERIK, empty load weight: 11,000 kg, counter spindle speed (max.): 5,000 rpm, The machine is expected to be available for approximately €4,000, including loading onto a truck (FOB). TECHNICAL DETAILS Working area X1-axis: 1,190 mm Working area Y1-axis: 120 mm Working area Z1-axis: 260 mm Working area X3-axis: 540 mm Working area Y3-axis: 120 mm Working area Z3-axis: 260 mm Handling space X1-axis: 490 mm Axes and Feed Feed force X1/Z1/Y1: approx. 8/10/10 kN Feed force X3/Z3/Y3: approx. 8/10/10 kN Rapid traverse speed X1/Z1/Y1: approx. 80/40/7.5 m/min Rapid traverse speed X3/Z3/Y3: approx. 40/40/7.5 m/min Acceleration X1/Z1/Y1: 7/7/7 m/s² Acceleration X3/Z3/Y3: 7/7/7 m/s² Spindle Speed at main and counter spindle: 5,000 RPM Power at 100% duty cycle, main spindle: 20 kW Torque at 100% duty cycle: 105 Nm Power at 40% duty cycle: 27 kW Torque at 40% duty cycle: 145 Nm Spindle bore: 65 mm Spindle diameter at front bearing: 110 mm Spindle nose diameter (cylindrical): 140 mm Hydraulic full-stroke cylinder OVS80 - Main spindle Piston stroke: 32 mm Piston area: 34.36 cm² Clamping pressure: 8 to 80 bar Tensile or compressive force at 80 bar: max. 27.2 kN Leakage oil volume at operating pressure 80 bar: max. 2.2 l/min Hydraulic full-stroke cylinder OVS65 - Counter spindle Piston stroke: 32 mm Piston area: 26.1 cm² Clamping pressure: 8 to 100 bar Tensile or compressive force at 100 bar: max. 26.1 kN Leakage oil volume at operating pressure 100 bar: max. 3 l/min Y-axis Slide travel: 120 mm Feed force: 10 kN Rapid traverse: 7.5 m/min Resolution: 0.05 mm Speed of driven tools: 6,000 RPM MACHINE DETAILS Control system: Siemens SINUMERIK Unloading device Swivel angle: 90 degrees Swivel time: 2 s Njdpfx Alszdqdfsnocu Slide travel: 100 mm Rapid traverse speed: 6 m/min Workpiece weight: approx. 10 kg Workpiece diameter: 200 mm Electrical data Rated power: 45 kW Apparent power: 53 kVA Rated current: 76 A Voltage: 400 V Frequency: 50/60 Hz Dimensions and weight Dimensions with chip conveyor (L x W x H): 2,770 x 4,435 x 2,750 mm Weight: approx. 11,000 kg EQUIPMENT Two tool holders with 12 tool positions each, VDI 30 Note: Further technical data can be found in the attached data sheet. The machine is not equipped with a B-axis.

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, center width: 1,500 mm, center height: 250 mm, swing diameter over bed slide: 500 mm, spindle speed (max.): 2,800 rpm, controller model: Monforts Control System MTC K, The machine was overhauled in 2017! The corresponding invoices are available upon request. TECHNICAL DETAILS Swinging diameter over bed: 500 mm Swinging diameter over slide: 290 mm Distance between centers: 1,500 mm Spindle bore: 70 mm Center height: 250 mm Spindle speed: 2 - 2,800 rpm MACHINE DETAILS Control system: Monforts Control System MTC K Control method: Teach-in Dimensions & Weight Dimensions (L x W x H): 3,350 x 1,550 x 1,800 mm Net weight: 3,300 kg Transport packages: 1 EQUIPMENT Nedszdfzaopfx Alnocu Fixed steady rest 3-jaw chuck Documentation CE marking

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, spindle speed (max.): 3,500 rpm, travel distance X-axis: 271 mm, travel distance Y-axis: 600 mm, center width: 600 mm, Equipment: bar feeder, chip conveyor, TECHNICAL DETAILS Turning diameter over bed: 350 mm Distance between centers: 600 mm Bed width: 210 mm Travel in X-axis: 271 mm Travel in Y-axis: 600 mm Spindle bore: 62 mm Maximum spindle speed: 3,500 rpm MACHINE DETAILS Control system manufacturer: Siemens Power: 30.0 kW Nodpfezdd Npjx Alnecu Dimensions & Weight Dimensions (L x W x H): 4,300 x 2,100 x 2,100 mm Net weight: 5,000 kg EQUIPMENT Chip conveyor Three-jaw chuck Bar feeder Driven tools C-axis Note: The parameters are stored, but are lost if the power supply is interrupted. As long as the power supply is maintained, this is not a problem.

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 7402-09-03006-03, spindle bore: 90 mm, rotational speed (max.): 2,000 rpm, center width: 3,000 mm, center height: 325 mm, controller model: SIEMENS SINUMERIK 810D, TECHNICAL DETAILS Swinging diameter over bed: 630 mm Swinging diameter over carriage: 380 mm Center height: 325 mm Distance between centers: 3,000 mm Carriage overhang on bed: 700 mm Bed width: 520 mm Longitudinal travel X-axis: 355 mm Longitudinal travel Z-axis: 3,000 mm Tailstock spindle diameter: 100 mm Tailstock spindle travel: 180 mm Maximum workpiece weight between centers: 3,000 kg Maximum workpiece weight in cantilever mode: 500 kg Spindle bore: 90 mm Spindle mounting: DIN 55027/8 Spindle taper: 120 mm Front spindle bearing: 130 mm Main drive power 100% ED / 40% ED: 12 / 18.5 kW Maximum torque: 2,400 Nm Speed: 2–2000 rpm Speed ranges: 3 Range 1: 2–220 rpm Range 2: 50–660 rpm Ncedszc Hmnepfx Alnsu Range 3: 100–2000 rpm Speed control: 50–120 % MACHINE DETAILS Control system: SIEMENS SINUMERIK 810D Load display on screen: 0–140 % Main drive: 10 kW Power supply: 3 × 400 V / 50 Hz Dimensions & Weight Dimensions (L (with chip conveyor) x W x H): 5,600 x 1,950 x 1,850 mm Machine weight: approx. 5,500 kg

Condition: ready for operation (used), Year of construction: 1998, functionality: fully functional, turning length: 500 mm, turning diameter: 300 mm, spindle bore: 75 mm, spindle speed (max.): 3,800 rpm, controller model: OSP 5000L-G CNC-System, No minimum price – guaranteed sale to the highest bidder! Turning machine with integrated Okuma robot! TECHNICAL DETAILS Turning diameter over cross slide: 450 mm Turning length: 500 mm Turning diameter: 300 mm Spindle bore: 75 mm Spindle speed: 70 - 3,800 rpm Spindle power: 11 kW (30 min) / 7.5 kW continuous operation Travel X-axis: 400 mm Travel Z-axis: 500 mm Rapid traverse X-axis: 12 m/min Rapid traverse Z-axis: 12 m/min Feed rate XZ: 12,000 mm/min Data transmission: RS232 Tool turret: 12 positions MACHINE DETAILS Control system: OSP 5000L-G CNC system Data transmission: RS232 Tool turret: 12 positions Power supply: 3 × 400 V Rated machine power: 21 kVA Maximum load current: 36 A Dimensions & Weight Dimensions (L (with chip conveyor) x W x H): 3,900 x 1,800 x 1,800 mm Machine weight: approx. 4,500 kg EQUIPMENT Integrated Okuma robot Automatic parts feeding Nodszc E Dfopfx Alnscu Ideal for series and automated turning operations Stable and durable design

Condition: ready for operation (used), functionality: fully functional, turning diameter: 660 mm, spindle bore: 76 mm, spindle speed (max.): 5,000 rpm, controller model: MAZATROL Fusion 640 MT, spindle torque (max.): 349 Nm, TECHNICAL DETAILS Turning diameter max.: 660 mm Main spindle Speed range: 35–5,000 rpm Power (10 min / continuous operation): 22 / 15 kW Torque max.: 349 Nm Spindle bore: 76 mm Chuck diameter: 210 mm C-axis indexing: 0.0001° Sub spindle Speed range: 35–5,000 rpm Power (10 min / continuous operation): 18.5 / 15 kW Torque max.: 326 Nm Chuck diameter: 210 mm C-axis indexing: 0.0001° Cooling Coolant tank volume: 300 l Pump capacity: 20 l/min Pump pressure: 5 bar Compressed air requirement: 5 bar, 500 l/min MACHINE DETAILS Ncsdpfjzgufrsx Alnju Control model: MAZATROL Fusion 640 MT Total power consumption: 66 kVA Operating voltage: 400 V / 50 Hz EQUIPMENT Technical documentation Chip conveyor with cooling system 20-position tool magazine B-axis (positioning in 0.001° increments) C-axis Y-axis Angular positioning of the sub spindle Synchronization of main and sub spindle Tool setting system (Tool Eye) Interlock for the front door Complete cooling system Interface for IC memory card

Condition: ready for operation (used), functionality: fully functional, turning diameter over cross slide: 402 mm, turning length: 758 mm, turning diameter: 450 mm, spindle speed (max.): 3,000 rpm, turning diameter over bed slide: 582 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum turning diameter: 450 mm Maximum turning length: 758 mm Ncodpfx Alozgt U Senou Diameter of rotation over the bed: 582 mm Diameter of rotation over the cross slide: 402 mm Spindle speed: 3,000 rpm Maximum spindle torque: 351 Nm Distance between centers: 744 mm Bar diameter: 81 mm Chuck size: 260 mm (10") Maximum bar diameter: 40 mm Axes: X, Z Number of tool positions in the tool changer: 12 Tool shank size: 25 × 25 mm Travel in the X-axis: 250 mm Travel in the Z-axis: 790 mm Rapid traverse rate in the X/Z direction: 30 m/min MACHINE DETAILS Control model: Hurco WinMax Spindle power: 22 kW Power supply: 400 V / 50 Hz (market-dependent) Machine weight: approx. 5,000 kg

Condition: ready for operation (used), Year of construction: 2008, functionality: fully functional, machine/vehicle number: X2S174, turning diameter over cross slide: 246 mm, turning length: 1,200 mm, spindle speed (max.): 2,700 rpm, turning diameter over bed slide: 400 mm, controller model: Fanuc 0i-TF Plus, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Swinging diameter over bed: 400 mm Swinging diameter over cross slide: 246 mm Swinging diameter in the steady rest area: 585 mm Spindle speed range: 1–2,700 rpm Distance between centers: 1,200 mm Spindle bore: 55 mm / 80 mm Spindle nose: D1-6 Camlock Chuck size: 250 mm Axes: X, Z MACHINE DETAILS Control model: Fanuc 0i-TF Plus Main motor power: 7.5 kW Nedpfxjzgt Ure Alnjcu Machine weight: approx. 2,200–2,500 kg EQUIPMENT Coolant system Manual tailstock Automatic lubrication of guideways and ball screws

Condition: ready for operation (used), Year of construction: 2005, functionality: fully functional, turning length: 81 mm, turning diameter: 99 mm, spindle speed (max.): 4,000 rpm, travel distance X-axis: 300 mm, travel distance Z-axis: 240 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Maximum turning length: 81.3 mm Maximum turning diameter: 99.1 mm X-axis: 300 mm Z-axis: 240 mm Spindle head: A2-6 Spindle bore: 33 mm Speed (variable): 4,000 rpm Spindle motor power: 11 kW Number of tools on the turret: 8 Number of driven tools: 10 MACHINE DETAILS Control: Fanuc 21iT Dimensions & Weight Machine dimensions (including chip conveyor): 290 x 235 cm Machine weight: 4,000 kg Dimensions of transformer station: 65 x 60 cm Weight of transformer station: 150 kg Overall dimensions (L x W x H): 2,600 x 2,300 x 2,400 mm Nedpfxozfg E Is Alnjcu Total weight: 3,900 kg EQUIPMENT Chip conveyor

Condition: ready for operation (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: ML0313-000510, turning length: 1,275 mm, turning diameter: 481 mm, spindle speed (max.): 2,800 rpm, travel distance X-axis: 260 mm, travel distance Z-axis: 1,350 mm, The machine has only been in operation for approximately one year! Nedpfxszf I Scs Alnjcu MACHINE DETAILS Power supply: AC 380 V, 3 phases, 50/60 Hz Rated power: 36.11 kVA Full load current: 54.87 A Machine weight: 6,900 kg FEATURES CNC control with operator panel Tool turret Tailstock Spindle chuck Enclosed working area Long-bed design CE marking The following data is taken from a manufacturer's data sheet. The seller assumes no liability for its accuracy: TECHNICAL DETAILS Standard spindle chuck, main spindle: 12″ Maximum turning diameter: 481 mm Maximum turning length: 1,275 mm Travel distances Rapid traverse X-axis: 24 m/min Rapid traverse Z-axis: 30 m/min Travel X-axis: 260 mm Travel Z-axis: 1,350 mm Main spindle Spindle speed max.: 2,800 rpm Spindle power max.: 35 kW Spindle torque max.: 1,613 Nm Tool changer Number of tools: 10 MACHINE DETAILS Dimensions & Weight Dimensions (L x W x H): 4,633 x 2,394 x 2,110 mm Machine weight: 6,900 kg

Condition: new, Year of construction: 2024, functionality: fully functional, machine/vehicle number: G1115-0025, turning length: 2,100 mm, turning diameter: 610 mm, spindle speed (max.): 1,500 rpm, bar diameter (max.): 165 mm, controller model: Fanuc i Serie, The machine is new and has no operating hours! TECHNICAL DETAILS Turning length: 2,100 mm Maximum turning diameter: 610 mm Y-axis travel: 150 mm Spindle Speed: 1,500 rpm Maximum bar diameter: 165 mm Torque: 2,990/2,459 Nm Spindle nose: A1-15 Spindle bore: 21" 2-speed geared spindle Tool turret Tool positions: 12 x BMT 75 Speed of driven tools: 4,000 rpm Axes and tailstock Tailstock: MT #6 Nedpfxezdztds Alnjcu Tailstock stroke: 120 mm C-axis available MACHINE DETAILS Control model: Fanuc i series Power: 45/37 kW EQUIPMENT C-axis Steady rest optional

Condition: used, Year of construction: 1982, Technical details: faceplate diameter: 2600 mm Ncjdpfx Ajwtctyolnsu turning diameter over support: 2500 mm turning length: - mm centre distance: 1600 mm turning diameter over bed: 2900 mm spindle bore: 100 mm revolution per minute: gear steps U/min feed range: Überdrehen 0,12-31,5 Plandrehen 0,12-45 mm/min bed guideways length: 2900 mm max. workpiece weight between centres: 400.000 kgs total power requirement: 45 kW weight of the machine ca.: alle Komponenten zusammen: ca. 29,0 t machine dimensions LxWxH: 5.2 x 5,0 x 3,1 m 3-way measuring system with digital display RSF electronics Control panel Cooling unit for Rittal electric cabinet *