Used Electrostatic for sale (108)

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 Csdpfxszduplo Aiijri 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Year of construction: 2021, operating hours: 480 h, condition: like new (used), functionality: fully functional, Electrostatic separator (corona) - EBS-4-271200 - builded to extract the metals from the rejection of the plastic from electric cable process Including additional options: - 3 screw transporters; - 3 m3 input hopper; - mechanisms for changing material flow and stand for big bag for mix collection; - touch screen for control cabinet english / rusian language; - set of spare parts Designed for dry high-efficiency separation of materials, that are differ in their electric properties: - mixtures of plastics and metals, including shredded cables, into metal (copper, aluminium), and non-conducting material (plastic); - mixture of different materials, provided that one of the components has conducting properties (extraction oftextilecord from rubber crumb in the processing of used tires ); - shredded WEEE (including PCB’s) into metal (aluminium, copper, nickel, bronze, and other) and nonconducting materials (plastic, textolite, fiber-glass plastic, and other), and also for: - separations of non-metal raw material (feldspar, pegmatite, quartz sand); - enrichingofdroughconcentratesofores of rare metals (titan-zirconia, tantalum- niobic, tin-tungsten, monazite), ores of precious metals (gold, silver); - benefication of diamond ore. The equipment was purchased at the end of 2021 directly from the prestigious manufacturer PRODECOLOGIA, which also installed it in our factory. Credpfjwcp I Aex Aiiji The equipment works perfectly and can be tested at any time with PVC plastic, from our Guidetti plant for electric cable recycling. Upon request, we can also provide installation + commissioning at the buyer's location. PRICE : 108 000 EURO- netto

Condition: excellent (used), Year of construction: 2018, machine/vehicle number: 30111, functionality: fully functional, operating hours: 123 h, The OekoRona M is an electrostatic precipitator that significantly reduces fine dust emissions from automatic wood-fired heating systems with outputs between 300 kW and 3 MW. The precipitator has a modular design and can be installed in both new and existing systems. The mechanical cleaning system enables fully automatic operation of the precipitator and reduces maintenance to a minimum. OekoRona M facts: - for automatically fed wood-fired heating systems up to 3 MW - automatic, mechanical cleaning - tested separation efficiency - low operating costs - retrofittable - suitable for overpressure and underpressure operation - bypass - low energy consumption - various designs - flexible ash removal - operating optimization through remote maintenance Manufacturer: OekoSolve AG Type: OekoRona M Identification number: ORM-30111 Csdj Aba Rgjpfx Aiiori Specified electrical power consumption: 1.65 kW Temperature class: T250 (according to the specified marking) Operating principle The flue gas flows through the tubes of the filter system, which are equipped with ionization electrodes. The high voltage electrically charges the fine dust particles, which then deposit on the inner surfaces of the separation tubes. The mechanical cleaning system automatically removes the deposited dust particles, which then fall into a lower collection container. An automatic discharge screw can transport the dust to an external collection container. Key technical features Feature Description Application area Automatic biomass-fired heating systems Boiler output range Approx. 300 kW to 3 MW for the product series Dust separation Electrostatic Cleaning Automatic mechanical cleaning Flue gas temperature Maximum 250 °C Operating mode Suitable for overpressure and underpressure systems Bypass Integrated bypass Operation Touchscreen control Dust removal Collection container; screw discharge, depending on the design or optional Condensation protection Electrical or hydraulic heating, depending on the design Installation After the boiler in the boiler room

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Cedjyg H Erspfx Aiiori Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 Crjdpfx Aieyg H Dhoioi 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, power: 0.14 kW (0.19 HP), input voltage: 230 V, type of input current: AC, volume flow: 1,890 m³/h, filter area: 7.9 m², noise level: 65 dB, actuation type: electric, total height: 575 mm, total length: 600 mm, total width: 590 mm, overall weight: 55 kg, Equipment: CE marking, documentation/manual, LTA electrostatic dust extraction system Intake on the right The intake nozzle can be screwed on as needed; currently, there is none, as it was previously mounted directly on the housing wall. In very good, fully functional condition, and naturally completely cleaned. Cjdpfx Aiozqttcoijri Available for immediate delivery.

Condition: good (used), Year of construction: 2013, operating hours: 37,297 h, functionality: fully functional, travel distance X-axis: 3,400 mm, travel distance Y-axis: 2,300 mm, travel distance Z-axis: 1,000 mm, rapid traverse X-axis: 60 m/min, rapid traverse Y-axis: 60 m/min, rapid traverse Z-axis: 40 m/min, controller manufacturer: Siemens, controller model: 840D sl, table width: 1,500 mm, table height: 30 mm, table length: 2,000 mm, table load: 2,000 kg, spindle speed (max.): 18,000 rpm, operating hours of spindle: 12,486 h, spindle motor power: 24 W, number of slots in tool magazine: 21, Equipment: documentation/manual, rotational speed infinitely variable, For sale is an EiMa CNC-controlled 5-axis machining center, type Sigma M, with a fixed portal and moving table, designed for the precise machining of aluminum and finishing of steel. The machine is engineered for high accuracy, rigidity, and large travel paths, making it ideal for demanding milling, drilling, and sawing operations in metal and aluminum profile applications. Year of manufacture: 2013 Power-on hours: approx. 37,297 h (as of November 2025) Spindle running time: approx. 12,486 h total (as of November 2025) AXIS TRAVEL & DYNAMICS: - X 3,400 mm · Y 2,300 mm · Z 1,000 mm - Feed rate: X/Y 60 m/min, Z 40 m/min STRUCTURE & TABLE: - Sturdy steel construction, precision linear guides, servo drives, automatic central lubrication - Moving table 2,000 × 1,500 mm, 30 mm thick, threaded grid 100 × 100 mm - Max. load capacity 2,000 kg SPINDLE & TOOL CHANGER: - 24 kW HSK 63 A spindle up to 18,000 rpm, water-cooled Cedpfx Asx H Ib Nsiijri - Disc-type tool changer with 20 positions + 1 pick-up position (for tools up to Ø 500 mm) 5-AXIS HEAD: - C3 fork head, swiveling ranges approx. C ±200°, A ±120°, high positioning accuracy MEASURING SYSTEMS: - m&h wireless probe (workpiece measurement) - BLUM laser (tool measurement) EQUIPMENT: - MMS system (internal & external lubrication) - Fully enclosed cabin, separate tool change chamber - Mist extraction system with electrostatic separator (approx. 1,900 m³/h) already integrated CONTROL: - Siemens 840D sl, 5-axis package, Advanced Surface, TCP - 15" control panel, remote maintenance prepared ACCURACY: - Repeatability approx. ±0.012 mm SPECIAL FEATURES: - Connected to power – demonstration possible at any time - Direct from production – no dealer sale - Complete technical documentation available - Support with dismantling, loading, and transport possible (at extra cost) HIGHLIGHT: - New spare spindle from Omlat included (approx. €25,000 value) NOTE: - Collection possible from January/February onwards All information has been provided to the best of our knowledge and belief. Subject to change, errors, and prior sale.

Condition: like new (used), Year of construction: 2020, functionality: fully functional, For sale is an Oerlikon Nonwoven ecuTEC+ electrostatic charging machine, designed for the electrostatic charging of filter media. The machine is intended for integration into a production line and processes material webs with a width of up to 1,700 mm. The material is guided through the machine by a system of deflection rollers and electrostatically charged using charging bars. The system is equipped with an HMI control panel and can operate in constant-current or constant-voltage mode. The machine has seen very little use and is being offered due to changes in the production setup. Manufacturer: Oerlikon Nonwoven / Oerlikon Neumag Crsdezumiropfx Aiiei Model: ecuTEC+ Year: 2020 Application: electrostatic charging of filter media Maximum material width: 1,700 mm HMI operator panel Adjustable charging system Constant-current / constant-voltage operating modes Designed for integration into an industrial production line CE documentation available According to the manufacturer's documentation, the material is guided through the machine via seven deflection rollers and electrostatic charging takes place at four charging positions. The system includes the machine frame with safety guarding, deflection roller/charging section, electrical cabinets with control electronics and high-voltage generators, and touchscreen control panel. Condition: Used, very low operating use. The machine is currently dismantled/disconnected from the production line. Detailed technical documentation is available. A comprehensive PDF specification/manual can be provided to interested buyers upon request. Inspection can be arranged by appointment. Further information, photos and documentation are available on request.

Condition: ready for operation (used), We offer a ready for use hamos EKS 1031 electrostatic separator for plastics. This machine is designed for efficient separation of mixed plastic materials using electrostatic technology. Ideal for recycling and industrial processing applications. Condition: ready for use Voltage: 400 V Frequency: 50 Hz Type: EKS 1031-0 The machine is in good working condition. Inspection possible. Codpfx Aoyv Hzaeiieri Location: Lithuania For more information, please contact us.

Condition: ready for operation (used), Year of construction: 2007, operating hours: 61,700 h, functionality: fully functional, machine/vehicle number: 7831, spindle motor power: 5,500 W, turning length: 231 mm, spindle speed (max.): 10,000 rpm, turning diameter: 25 mm, spindle bore: 25 mm, overall weight: 3,000 kg, rotational speed (max.): 10,000 rpm, type of input current: three-phase, feed length Y-axis: 534 mm, feed length Z-axis: 230 mm, total width: 1,400 mm, total length: 2,400 mm, total height: 2,060 mm, feed rate X-axis: 30 m/min, feed rate Y-axis: 30 m/min, feed rate Z-axis: 30 m/min, bar diameter (max.): 25 mm, quill travel distance: 230 mm, quill diameter: 25 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, input voltage: 400 V, power: 5.5 kW (7.48 HP), travel distance X-axis: 58 mm, travel distance Y-axis: 534 mm, travel distance Z-axis: 230 mm, operating pressure: 6 bar, Equipment: documentation/manual, rotational speed infinitely variable, Tornos Deco SIGMA 20s Swiss-type automatic lathe, including Robobar SBF-532 3000mm bar feeder, Mayfran Consep chip conveyor with drum filter (unique version), electrostatic oil mist collector, and an automatic CO₂ fire suppression system (Kraft & Bauer). Fitted with a Fanuc 31i-model A CNC control, spindle speeds up to 10,000 RPM on both the main and sub spindles. The machine features 6 axes and 22 tooling positions: Main spindle: 12 positions, 6 of which are driven (up to 6,000 RPM) Sub spindle: 10 positions, 6 of which are driven (up to 6,000 RPM) Also equipped with high-pressure coolant, up to 80 bar. The machine can be inspected under power. Dismantling and transport are the responsibility of the buyer. Parts included with the machine: • External holder left, long – 6× (417608) • External holder left, short – 1× (417606) • Single driven holder, reduced speed – 2× (417612) Crjdpfjyrg Ahox Aiiei • Double clamping, long – 2× (417617) • Double clamping, short – 2× (417620) • Driven block – 2× (417624) Bushings for pusher diameters (216787): • Ø10 • Ø16 • Ø20 • Ø25 Ejector set: • Ø5 to Ø20 (in 1 mm increments)

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Crjdeflk Awspfx Aiioi Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: new, Year of construction: 2025, Curing ovens shown in the photos can vary in price depending on size, configuration, and optional features. 💡📏⚙️ At ROMER, we manufacture both standard models and fully bespoke solutions, tailored to your process requirements. 🏭✅ Tell us your part size, line capacity, curing profile, and available space - and we will propose the best setup and the options that actually improve daily performance. 🔥🎯 🧠📡 Control and monitoring Live process control for temperature, time, airflow, and modes - with alarms and saved recipes for repeatable cycles. 🔁✅ Codpfxsfz U Nbs Aiisri 🔥🧩 Heating module Fast heat-up and stable temperature thanks to efficient heating elements and quick energy transfer. ⚡🌡️ 🌀💨 Air circulation Uniform airflow reduces temperature differences for consistent coating quality. 🎯✅ 🧱❄️ Insulation and design Smart chamber construction minimizes heat loss - faster reaching setpoint, lower consumption. ♻️📉 🛡️⚠️ Safety and certification Sensors, interlocks, and protection logic increase safety and reliability. 🔒👷 ⚡💰 High efficiency Optimized heat transfer and reduced losses mean real operating savings. 📉🔥 ⏰🤖 Automatic start Programmable schedule - automatic preheating before the shift for smoother production starts. ⏱️✅ 🚪🔒 Self-latching doors + intelligent chimney Prevents accidental opening, chimney activates only when needed for safer operation. 🧯✅ 🌿🔋 ECO mode Low-energy standby when idle - fuel consumption reduction up to 20% (depending on process). 🌱📉 👀💡 View and lighting Inspection without opening the door - fewer temperature drops, easier supervision. ✨👁️ 🛤️🔥 Guide rails + automatic hood Heat hood runs only during loading to reduce temperature loss, automatic rail infeed improves ergonomics and loading speed. 🙌⚙️ 🎛️🌡️ MULTI-ZONE HEAT Independent zone control for uniform curing of parts with different mass and geometry. 🧩✅ 🧠♨️ MTS system Heating elements mounted without thermal bridges - higher efficiency and faster time to set temperature. ⚡⏱️ 2-in-1 🧱↔️🧱 Split chamber Movable partition for two independent zones - drying and curing in one unit for maximum flexibility. 🚀🔁 🎚️🌀 VFD ventilation Variable fan speed based on chamber conditions - better control and lower electricity use. ⚙️💡

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, • Year 2004 • In our possession since 06/2023 • Complete clamping system, with two modified clamps for Ø14 and Ø16 • Automated pallets with diameters of Ø3, Ø4, Ø6, Ø10, Ø12 • Various grinding wheels for roughing and finishing, some new, for both carbide and HSS • Parkair electrostatic dust extractor • New user interface keyboard (3-4 years old) • New workpiece rotation belt (replacement due in 2025) Cjdpszcvakofx Aiijri • Less than 100 operating hours since 2023 • Dedicated Transor filtration tank, year 2007, maintained with filter changes and complete functionality check, with service performed in 07/2023 (over €3000 + VAT), less than 100 operating hours since the maintenance -separate sale can be considered- • Machine price: €25,000 - Filtration system price: €10,000

Condition: excellent (used), Year of construction: 2015, operating hours: 12,068 h, functionality: fully functional, workpiece weight (max.): 20 kg, spindle speed (max.): 10,500 rpm, type of input current: three-phase, grinding wheel diameter: 200 mm, overall weight: 5,200 kg, grinding length: 350 mm, feed rate X-axis: 15 m/min, feed rate Y-axis: 15 m/min, feed rate Z-axis: 15 m/min, travel distance X-axis: 460 mm, travel distance Y-axis: 320 mm, travel distance Z-axis: 660 mm, grinding spindle motor power: 14,500 W, input voltage: 400 V, CNC Tool grinding machine WALTER Helitronic Power Diamond TECHNICAL CHARACTERISTICS: Year of manufacturing: 2015 CNC control: FANUC Series 31i-B5 Software installed: Tool Studio 2.1 R8 Colour touch screen: 15 ["] Number of axes: 5 Stroke X axis: 460 [mm] Resolution X axis: 0.0001 [mm] Stroke Y axis: 320 [mm] Resolution Y axis: 0.0001 [mm] Stroke Z axis: 660 [mm] Resolution Z axis: 0.0001 [mm] Traversing feeds X, Y and Z axes: 15000 [mm/min] Stroke A axis: 360 [°] Stroke C axis: +/- 200 [°] Resolution C axis: 0.0001 [°] Max. workpiece lenght : end face grinding: 280 [mm] Max. grinding lenght: 350 [mm] Max. grinding diameter: 320 [mm] Grinding spindle attachment: HSK-50 Max. grinding wheel speed: 10500 [rpm] Grinding spindle motor power: 14.5 [kW] Max. diameter grinding wheel: 200 [mm] Workpiece spindle nose: ISO 50 Max. part weight in part holder headstock: 20 [Kg] Working hours: 12068 [h] Coolant pump pressure: 7 [bar] Collant pump flow rate: 80 [l/min] Supply voltage: 400 [V] Total power required: 20 [kVA] Weight: 5200 [Kg] ADDITIONAL EQUIPMENT: CO2 fire extinguishing system (to be inspected by the buyer through a qualified body) A-axis for cylindrical grinding (Hollowshaft option) 8-position grinding wheel changer Electrostatic mist separator with noise silencer, DSL type AES-GAMMA 30 Hydraulic and electrical connections for automatic steady rest operation Automatic steady rest Manual tailstock Combined filtration system with paper band filter + cartridge filters, connected to a cutting fluid cooling unit 3-color signal tower light "Eco Loader" tool loader with its tool clamping system and 5 cassettes (Ø6, Ø8, Ø10, Ø12 and Ø16) E386ES tool clamping chuck with 5 collets (Ø8, Ø10, Ø12, Ø16, Ø20) Grinding wheel holders x2 electrode holders L = 25 mm x1 electrode holder L = 45 mm x5 grinding wheel holders L = 45 mm Crsdpfx Aio Ahpfbsisi SOFTWARE: TOOLSTUDIO Standard & Advanced TOOLSTUDIO Step Tools License TOOL STUDIO PC License WALTER WINDOW MODE (P1, P2 & P3) for grinding (P51 & 52 for erosion) WALTER WINDOW MODE Package 63 for PCD drills More information upon request.

Condition: ready for operation (used), Year of construction: 2006, functionality: fully functional, machine/vehicle number: 2441.05, cutting force: 1,122 t, total width: 9,000 mm, total length: 19,000 mm, total height: 5,700 mm, overall weight: 320,000 kg, operating pressure: 350 bar, loading space height: 1,800 mm, cutting width (max.): 810 mm, DGUV certified until: 11/2026, ejection height: 850 mm, filling opening length: 7,500 mm, filling opening width: 2,300 mm, The described scrap shear from Leimbach, including the associated conveyor belt, is for sale. The machine is in operation. An inspection at our facility is possible by prior arrangement in 68219 Mannheim. In addition to the existing oil filtration system, an electrostatic oil purification system from Kleentek has been installed. Codpfxezzxbte Aiiori The machine is available upon agreement. Further information is available upon request. Delivery terms: EXW Mannheim, Rheinauhafen. The dismantling of the goods and its subsequent loading onto the means of transport will be carried out at the buyer's expense and risk. The selling price and delivery terms are negotiable. The sale is exclusively to commercial customers. This offer is non-binding and is subject to a technical and legal review as well as a contractual agreement between the parties.

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, Intake pipe: 180 mm Voltage: 230 V, 50 Hz Filter area: 6.0 m² Conveying capacity: 1000 m³/h Cedsvrfv Aspfx Aiijri Total power requirement: 0.3 kw Machine weight approx.: 78 kg Dimensions L-W-H: 400x600x700 mm Electrostatic separator: Filter chamber L: 360 x W: 510 x H: 500mm 3 slots with: -Pre-filter (knitted stainless steel) 500x370x20mm -Ionizer/collector cell 500x370x210mm -Post-filter (knitted stainless steel) 500x370x20mm

Condition: used, Year of construction: 2011, operating hours: 2,200 h, functionality: fully functional, power: 7.5 kW (10.20 HP), year of last overhaul: 2026, We offer this used Schneeberger Norma CFG 7.5 kW tool grinding machine, manufactured in 2011, for sale. OPERATING HOURS: 2200! Automatic programmable central lubrication system Pneumatic hoses completely renewed 4/2026 Standard version PLUS: - Hydraulic quick tool clamping system - Grinding wheel spindle HSK 50 - Quinto-Basic-SW woodworking tools - Coolant filter unit 330l; 6.3 bar - CO² fire protection system Special accessories: - Manufactured in 2013 - Workpiece loader MIL incl. quick-change tool holder for profile cutters and shank tools - 1 piece of pallet for profile cutters - profile thickness: 2mm; plate width up to 150mm Codpfxjzqu Tdo Aiijri Machine Specifications – NORMA CFG (Schneeberger Invoice No. 88088, dated 21.12.2011) MAIN MACHINE M-55039-0031 – CNC Tool Grinding Machine "NORMA CFG" Power: 7.5 kW Machine No.: 21'692 Voltage: 400V / 3-phase / 50Hz EQUIPMENT & OPTIONS M-51019-0021 – Automatic programmable central lubrication M-50019-0022 – Precision 3D touch probe PSM 118 M-82090-0003 – Network connection M-56009-1993 – Remote maintenance software, 2 years free M-50009-0191 – Dressing roller on mounting arbor M-530890098B – Hydraulic quick tool clamping, ISO 50 M-10030-0115 – Expansion collet chuck ISO 50, D=20 M-10030-0116 – Expansion collet chuck ISO 50, D=32 M-56039-0044B – Plate mount, hydraulic, horizontal M-50020-0211B – Intermediate layer 40 M-50020-0003B – Intermediate layer, standard M-56009-0643 (x6) – Grinding wheel mount HSK50, 20/70x85 M-45000-0000 – Quinto base software M-45000-0010 – Quinto standard tools M-45001-0210 – Quinto software eGrind viewer M-45000-7030 – Quinto software dxQ, woodworking inserts M-45001-0010 – Quinto easyPROFILE M-45000-1010 – Quinto software, woodworking tools M-50009-0190A – Flow monitor M-50019-0049 (x6) – Complete plate with coolant pipes M-55039-0059 – Coolant filter unit, 330 L, 6.3 bar M-50009-0036 – CO2 fire suppression system M-55039-0086 – Electrostatic extraction/suction unit M-600000-051 – Training in Roggwil/Weissach, 3 days M-600000-052 – Installation and follow-up training, 3 days in Gütersloh M-20000-0032 – Truck packaging M-20000-0050 – Transport incl. transport insurance (not unloaded), DAP DE-Gütersloh If you have any questions or need further information, please feel free to send us a message.

Condition: excellent (used), PRO XP85 MANUAL ELECTROSTATIC SPRAY GUN GRACO REF. L85T10 Cedpfoivt Risx Aiijri - Brand: GRACO - Reference: L85T10 -PRO XP85, Standard, BOQ. 1.5MM., 85KV. -Industry in general, metal, wood -Does not include hose, avaliable under demand - Second-hand product that has passed a very rigorous tuning - 1 year warranty. It is in like-new condition - VAT not included

Condition: like new (used), Year of construction: 2022, functionality: fully functional, complete plat concisting of: Bi-rail overhanging conveyor with two points bar support , lift and rotation unit Cjdpfx Asxw Ux Hsiiori Spray booth for robot with full recirculation, with autimatic pre-filter replacment system High pressure humidificer for spray booth and flash off room Robotic spray system for windows with jacket nozzle cleaning unit automatic color change (3 independent ) electrostatic safty system paint flow meter drying tunnel with ldp system and axial fans supervisor systeem with data interface and datamic reader “The line is packed for transport. It has been previously installed, but it has never been taken into operation.”

Condition: excellent (used), Year of construction: 2011, operating hours: 31,648 h, functionality: fully functional, machine/vehicle number: 90265 2011, saw blade diameter: 710 mm, tooth pitch: 55 mm, grinding wheel diameter: 200 mm, total width: 2,662 mm, total length: 2,540 mm, total height: 2,640 mm, type of input current: AC, input current: 10 A, input frequency: 50 Hz, disc diameter: 200 mm, grinding wheel bore: 32 mm, grinding spindle motor power: 3,000 W, saw blade width: 8 mm, input voltage: 400 V, overall weight: 3,200 kg, saw blade bore: 80 mm, power: 10 kW (13.60 HP), grinding diameter: 710 mm, workpiece diameter (max.): 710 mm, Equipment: rotational speed infinitely variable, CNC saw blade sharpening machine with lateral tooth divider grinding device and saw blade magazine for blades up to D=560 mm for unmanned operation. In manual mode: 40–710 mm. Saw blade magazine with 3 holding arbors. Oil filtration system for HSS, oil cooler brand Polar 2.9. Tooth geometries HSS: Form A, B, BW, C and special tooth forms. Saw blade holders for manual loading D=75 to 250 mm and D=40 to 100 mm. Special program for grinding variable tooth pitches. CAD program for creating up to 250 custom tooth shapes. Fire extinguishing system is an oil retrofit kit with aerosol extinguishing generator. With electrostatic air extraction. Codpfx Aiox Tct Tsiori

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, We are offering for sale our component cleaning system from Ziegener + Frick. The system is in like-new condition. Various loading frames are included. Cedpfx Aioz Enr Toieri ION Clean cleaning table. Summary with AI: The IONClean cleaning table from Ziegener + Frick is a soundproof, turnkey stand-alone system for contactless and electrostatic surface cleaning of components. You can find an example video from the manufacturer under Videos. We will gladly answer any questions you may have about the system. An inspection is possible by appointment. New price of the system: approximately €85,000.

Condition: ready for operation (used), Year of construction: 1999, • Year 1999 • In our possession since 08/2024 Cedpfxszcvaqo Aiijri • Quinto 4 software • Electrostatic filter, Elbaron model • Numerous spindles • Recent maintenance performed: external cleaning and repainting, spindle overhaul, spindle belt replacement, brush and front plexiglass replacement, wheel and door rail replacement, machine measurement, offset adjustment, ball reference setting, backlash check, replacement of the air filtration and lubrication adjustment unit, replacement of 4 electric fans.

Condition: like new (used), functionality: fully functional, Year of construction: 2015, total length: 1,290 mm, total height: 1,980 mm, total width: 900 mm, type of input current: three-phase, overall weight: 658 kg, input voltage: 240 V, input current: 40 A, temperature: 160 °C, input frequency: 50 Hz, ambient temperature (min.): 15 °C, ambient temperature (max.): 30 °C, positioning accuracy: 0.127 mm, electrical fuse: 40 A, repeat accuracy: 0.05 mm, feed length X-axis: 406 mm, feed length Y-axis: 355 mm, feed length Z-axis: 406 mm, space requirement length: 2,000 mm, space requirement height: 2,200 mm, noise level: 65 dB, space requirement width: 1,500 mm, High-performance industrial 3D printer based on FDM technology, designed for functional prototyping and low-volume production using certified engineering thermoplastics. The Stratasys Fortus 450mc is a proven platform for companies requiring repeatability, dimensional stability, and material traceability, making it suitable for automotive, aerospace, industrial equipment, and advanced R&D environments. The system is configured with dual extrusion heads in open material mode, enabling advanced process flexibility and compatibility with a broader range of FDM-grade thermoplastics, subject to parameter optimization and the thermal constraints of the platform. Crjdpfxjy Ug Ece Aiioi Key Features: - Heated build chamber (up to ~180°C) for superior layer adhesion and reduced warping - Industrial-grade repeatability for functional and end-use parts - Large build volume: 406 × 355 × 406 mm - Dual extrusion system (model + soluble support) - Closed material system for process stability and consistency - Compatible with Insight software for advanced process control Supported Materials: 🔹 Standard & Functional Polymers ABS-M30 → robust functional prototyping ASA → UV-resistant outdoor applications ABS-ESD7 → electrostatic dissipative components 🔹 High-Performance Polymers PC (Polycarbonate) → high impact resistance PC-ABS → balance between toughness and processability 🔹 Advanced Engineering Materials Nylon 12 (PA12) → wear resistance and fatigue durability Nylon 12CF (carbon fiber reinforced) → increased stiffness and dimensional stability 🔹 Aerospace-Grade Thermoplastics ULTEM 9085 → FST compliant (flame, smoke, toxicity) ULTEM 1010 → maximum thermal resistance and mechanical strength

Condition: ready for operation (used), Year of construction: 2007, operating hours: 14,136 h, travel distance X-axis: 1,300 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 800 mm, controller manufacturer: BOSCH, controller model: Rexroth, table load: 400 kg, spindle speed (max.): 15,000 rpm, spindle motor power: 16,000 W, number of axes: 4, This 4-axis Matec MATEC 30 HV/K was manufactured in 2007, featuring a robust vertical machining center design. It includes a Bosch Rexroth control, a standard spindle with a speed range of 20-15,000 rpm, and a maximum torque of 100 Nm. The machine offers a tool changer with a capacity of 36 tools and a machine table that supports up to 400 kg. If you are looking to get high-quality milling capabilities consider the Matec MATEC 30 HV/K machine we have for sale. Contact us for more information. Machine Benefits Qualitative Machine Benefits • The machine was manufactured in 2007 but was retrofitted in 2016 Technical Machine Benefits • Hard disk: 26 gb • Integrated network card • Max. Torque: 100 nm (40% ed) • Temperature-controlled liquid cooling • Work area: fully encapsulated with roof, bellows (steel slats) • Installation: height-adjustable set-up elements • Matec hv 30 was overhauled in 2016 by manufacturer matec maschinenbau Extra Information Cooling & Accessories Coolant: High-pressure Coolant Supply (20 bar, optional 40 bar) Paper Belt Filter (30 µm fineness) Tank Volume: 450 l Chip Conveyor: Integrated Scraper Conveyor Cjdpfxex D Ix Te Aiijri Oil Mist Extraction: Electrostatic Filter (1000 m³/h) Measuring & Safety Technology Direct Measuring System: Linear encoder in all axes 3D Measuring Probe: Radio transmission to the control system Tool Monitoring: Laser-supported Tool Breakage Monitoring Tool Length Measurement (software) Optional Spindle (HSK 63-A): Higher Power: 30 kW / 190 Nm Drilling Capacity (steel): up to 60 mm Milling Capacity: approx. 500 cm³/min Technical Specification Taper Size HSK 63

Condition: ready for operation (used), Year of construction: 2010, functionality: fully functional, total length: 9,000 mm, working height: 120 mm, For sale: BARBERAN PUR-33-L profile wrapping machine (year 2010) – machine for laminating elements with decorative foil using PUR hot-melt adhesive (hot gluing). The machine features a single foil feeder, automatic control, and an added antistatic corona system (reduces electrostatic charges – improves foil feed stability). Technical specifications: Model: BARBERAN PUR-33-L Year of manufacture: 2010 Machine length: approx. 9 m Max. element width: 120 mm Feed speed: up to 45 m/min Csdpeyw Nxkefx Aiijri Power supply: 400V / 50Hz Foil feeder: 1 unit Equipment / additional features: Antistatic corona (retrofitted) – neutralizes foil static Printer – enables edge printing (e.g. strip name / operator / description) Glue melter with approx. 60L capacity – allows extended operation without interruption. Important: The machine applies PUR adhesive using hot-melt technology Heaters are NOT included in the set.