Electrostatic separator (corona) - EBS-4

PRODECOLOGICA Electrostatic separator- EBS-4

Year of construction: 2026, condition: new, -Drum diameter 1600mm -Drum length 2880-3880-4880mm -Working length 2000-3000-4000mm -Grid holes according to your specifications -The screen consists of a closed profile -A cleaning brush with a diameter of 300 mm is mounted on the screen and along the entire length of the working part Ncodoq T Sp Hjpfx Afaer -Flat bar blades installed in the center of the drum allow the material to be poured -Drum rotation speed approx. 11.5 rpm - Sieve feed sieve via gearmotor- Drum transmission via gearmotor + 2 rubber drive wheels diameter 230 mm - Sieve equipped with electrical panel - Gravity feed hopper, dimensions Width 1600 mm, Length 1400 mm, Height 1200 mm - 12 months warranty - Made in Europe - CE compliant

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A Ncjdpfx Aowp Rqfjfaor • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: refurbished (used), Completely refurbished Bongioanni CRL 4 tensioning wagon with clamping blocks. Track gauge 1200 mm. Rails newly milled. Servo-electric drive. Sale upon customer order. Ncjdpfxextwxbo Afaor

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters Njdpsu Hmacofx Afaecr 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: Ncjdpfx Ajq Nf Ensfaer 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed Nedpfxovbtpe Afaocr -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm

Condition: new, functionality: fully functional, New machine - stock clearance sale - Tipping is mechanical. The stated price is net ex warehouse location. Njdpfx Afjw Sfdweascr

Condition: used, Year of construction: 2006, For sale: LBL Brente log transport wagon with debarker – year of manufacture 2006 Ncjdpfx Asx Ndpbofaor We will be selling a complete series of machines from a sawmill. This is the first machine from this lineup – keep a close eye on our website for additional offers. Dimensions and technical specifications can be found in the PDF documents.

Condition: reconditioned (used), Year of construction: 2003, Complete plant Primary impact mill, 2320x1700 mm. Mobile Production capacity 800 t/h 0-40 mm Limestone Secondary two Laron Lau 8 hammer mills, 1620x700 mm opening. Ncsdpfx Ajlwya Njfaor

Condition: good (used), functionality: fully functional, 2 Pcs. “Steinert NES 200 220 E 5009” for Sale Nodpfsxb Tbzsx Afaocr Manufacturer: Steinert Type: NES 200 220 E 5009 Belt widthness: 2.000 mm (New belt) With new control-unit. Overhauled, balanced, sandblasted and painted.