Used Beveller for sale (513)

Condition: refurbished (used), Year of construction: 2006, functionality: fully functional, measuring range X-axis: 1,800 mm, measuring range Y-axis: 200 mm, measuring range Z-axis: 650 mm, workpiece weight (max.): 180 kg, We are selling a refurbished Wenzel WGT350 XL rack and pinion measuring machine. The machine can be used to measure gears and racks. - Max. Rotary table workpiece diameter = 5 to 400mm - Max. Rotary table load = 180kg - Travel X= 1800mm Y=200mm Z=650mm - Counterholder measuring range = 20 to 900mm - Module measuring range from 0.5mm - Max. Max. rack length = 1200mm - 6x probe changer incl. 6x SP600M plates - Temperature compensation of the machine - Active air damping of the machine - Year of manufacture 2006 - Accessories such as, driver, reference ball etc. as shown - Jaw chuck D=200mm with inside and outside jaws The following software modules are included: - TMain - program management - TStylus - Probe management - TCali - probe calibration - TAmo - Calculated axis position determination - TGear - Cylindrical gear measuring program - TShaft - Program for dimension, form, position and scanning of unknown contours - contours - TWorm - Worm measuring program - TRack - Rack software Blsdpfevitkiox Abbsc - TReverse - The parameters of an unknown gear, module (mn), helix angle (ß) and pressure angle (a), can be determined with TReverse. can be determined. - Statistical program, statistical evaluation for spur gear, bevel gear and worm gear testing. worm testing For further information, please contact us by e-mail.

Condition: good (used), Year of construction: 2016, operating hours: 16,977 h, functionality: fully functional, feed length X-axis: 140 mm, feed length Y-axis: 50 mm, feed rate X-axis: 18 m/min, edge thickness (max.): 3 mm, total length: 6,000 mm, workpiece height (max.): 60 mm, overall weight: 3,000 kg, SCM OLIMPIC K 800 - T-ERL EDGEBANDER EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications: -- Edge Capacity, 0.4 to 8 mm (0.016 to 5/16") for strip feeding. -- Panel Capacity, min. width 50 mm and 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-3/8"). Equipped With: -- Adjustable In-feed Fence: Manually pre-set with digital indicator and pneumatic panel spacing device. -- Pre-Milling Station, RT-E: Spindles 2 x 3.0 HP, 12,000 RPM, (1) with PLC controlled jump action and manual digital indicators positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Servo motor positioning, (4) pressure rollers, first larger, Teflon coated and powered. Workstations: -- End Trimming Station K-SEL: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0 - 15, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Flush Trimming Unit: Top/Bottom, 2 x 1.0 HP, 12,000 RPM with 2 pre-set pneumatic positions, flush and overhang, remote pneumatic in/out positioning. -- Bevel/Radius Trimming Unit: Programmable, servo motor positioning, 2 x 1.0 HP - 12.000 RPM motors for change-over on the fly. -- Corner Rounding / Trimming Unit: For additional top & bottom trimming of linear an/or vertical leading & trailing corner when edgebanding all (4) sides, 2 x 0.8 HP - 12,000 RPM motor. -- Profile Scraping Unit "RAS/1000": Top/Bottom with (2) indexed manual pre-sets. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "RC-V": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit "SPN": Top/bottom, oscillating 2 x 0.25 HP - 3,000 RPM motors, tilting up to 12. -- Hot Air Unit: Single blower with adjustable heat range and directional heat shield for top/bottom coverage. Restores color luster on thick pvc edging materials that my be lost during the edge scraping process.Operator Interface: -- Startouch Controller, 12" color touch screen, swivels 270 at in-feed of machine. Capable to store (100) programs, (6) at the touch of a single key. Graphical display of all working units. Tracks production data, diagnostic information and monitors maintenance schedules. Complete With & Features: -- Feed-speed, 36/52 FPM, 1 x 2.5 HP feed drive motor, 200 Hz frequency inverter for all trimming units. -- Electronic, programmable hold-down pressure beam positioning, lighted safety/sound enclosure cover and outboard panel support. -- Actual Model: OLIMPIC K 800 T-FR2 2 glue tanks + 1 glue tank for spare parts Bjdpfjxxy Rkox Abbelc

Condition: used, Year of construction: 1961, functionality: fully functional, Horizontal Gear Hobbing Machine 5370 The machine is intended for milling slots on shafts, cylindrical spur and bevel gears, chevron wheels, external and internal threads, large-modulus worms, and worm wheels. Technical specifications of the machine: Maximum workpiece diameter: 600 mm Maximum hobbable module: 16 Longitudinal caliper travel: 2700 mm Lateral caliper travel: 390 mm Workpiece spindle bore diameter: 200 mm Main electric motor power: 10 kW Bsdpfeya U Syox Abbslc Machine dimensions: Length: 5960 mm Width: 2260 mm Height: 2400 mm Weight: 23 t

Condition: excellent (used), TruTool PN 200 electric hand cutting machine Product features The new TruTool PN 200 vibrating shear is mainly used for cutting C-L-U sections, trapezoidal sheet metal, etc. components. The device with a short tool for processing sheet metal with a profile depth of up to 85 mm and for C-L-U sections. Also for corrugated sheet metal. Ideal for hard-to-reach places. The working direction can be adjusted 360° easily and without tools in 45-degree steps. Minimized set-up time Replacement of punch and yoke without interruption and without tools. Unmatched speed Fast and efficient, 2.1 meters per minute at 400 N/mm2 structural steel. Application: Trapezoidal sheet metal For cutting profiles up to 86 mm deep and 132.5 / 40 mm wide. For straight and diagonal cuts. Profiles For cutting C-L-U profiles. Corrugated sheet For cutting and slitting. For bevel cuts and internal and radial cuts. - MAXIMUM SHEET THICKNESSES: - MAXIMUM THICKNESS OF 400 N/MM² STEEL SHEET: 2 mm. - MAXIMUM THICKNESS OF STEEL 600 N/MM²: 1.5 mm - MAXIMUM THICKNESS OF STEEL SHEET 800 N/MM²: 1 mm - MAXIMUM THICKNESS OF SHEET METAL MADE OF ALUMINUM UP TO 250 N/MM²: 3 mm - RADIANCES: Blodpfxeuhm E Se Abbsc - LOWEST RADIUS: 50 mm - GENERAL INFORMATION: - OPERATING SPEED: 2.1 m/min. - NUMBER OF SHAKES AT NOMINAL LOAD: 1500 1/min. - INITIAL HOLE DIAMETER: 24 mm - RATED POWER CONSUMPTION: 550 W

Condition: excellent (used), This conveyor belt machine is ideal for shearing the edges of small carpet samples. Diagram of K-50 The key component of the KS 50 edge beveling machine is our SE 50 cutting unit. The machine is designed with angle adjustment from 0° to 60°. The depth of cut is adjustable from 2 mm to 22 mm. The guide plate for carpet samples can be easily adjusted steplessly from 20 mm to 210 mm. Quick and easy adjustments can be made by releasing the locking lever. The conveyor belt is driven by a three-phase motor. Bjdpfeud Dqkox Abbelc The speed of the cutting motor and the conveyor belt is infinitely adjustable by means of frequency converters. Larger pieces of carpets are guided manually as they pass through. The cutting width is 50 mm.

Year of construction: 2005, condition: used, functionality: fully functional, power of the buffing unit: 52,000 W, For sale: Professional edge polishing machine Bellani Supermodulo, ideal for marble, granite, and quartz processing. The machine is in good working condition and features the reliable O.M.G.M. Electronic Control system for precise positioning. Key features: Model: Bellani Supermodulo. Control Unit: O.M.G.M. Electronic Control for convenient parameter adjustment. Configuration of working heads: 1x Calibration Head: For thickness regulation. 8x Polishing Heads: For flat or round edge finishing. Bodpfx Ajyaqmmobbolc 4x Beveling/Chamfering Heads: For upper and lower 45° bevels. 1x Drip Groove / Slot Cutting Head Functionality: Multi-head system for calibration, flat and round edge polishing, and beveling (chamfering). Technical details: Type: Edge Polishing Machine Manufacturer: Bellani Model: Supermodulo Year of manufacture: 2005 Condition: Used (Good) Status: Machine is currently in operation and available for inspection. Condition: Well-maintained for its age, with robust build quality typical of Bellani machines. The Supermodulo series is renowned for its durability and the high-quality finish it achieves on thick stone slabs. Ideal for workshops seeking a reliable, cost-effective solution. Location: Tosic MG, Vojvode Putnika 76, 18000 Nis, Serbia

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. Bedpfx Absi Ri Rvebjlc 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: cd0062ee491e6794168ccb01a, empty load weight: 8 kg, maximum load weight: 26 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 435/50 r 19,5, Further information Chassis semi-trailer In proven HANGLER welded construction made of high-quality steel with UP-welded side members tapered towards the front. Frame neck height 120 mm, with double center bar. Z-profile cross members punched through on the side member with floor panels (larger spacing) and with welded special side frame.2 kingpins to DIN 74080, replaceable, with grinding plate beveled to the front, made of high-quality sheet steel. EC front turning radius 2,040 mm. Sliding plate continuously welded from saddle plate to front plate *inside* 18 pairs of lashing eyes embedded in the outer frame, 2.5 tons each 8 pairs of lashing eyes embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side collision protection Plastic mudguards with splash protection mats Underride guard Impact protection at the rear Bedpfsi Riw Hsx Abbslc Spare wheel holder for 1 e-wheel, with wheel mounting kit 3 Plastic tool box, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Aluminum ladder 3 300 mm, loose Pair of recessed stanchion pockets Piece of stanchions Storage compartment for plug-in slats on one side in FR left, below loading area Storage compartment for drop sides underneath the cargo bed, open, if technically possible Coil trough/inclined loading device Coil trough 8,000 mm long with cover and rubber pad. Cover 35 mm. With inclined loading bars and supports suitable for FR 80/80/4, complete stanchions 80/80 incl. lower reinforcement supplied Hydraulic sloping loading device with 4 crossbars:Hydraulic supply via tractor unit by means of 2-pipe pump system (forward/return) with 2-fold Faster coupling mounted on bulkhead (hoses are connected to Faster coupling from below).Sloping loading bars (FR 180x100x8 mm) with integrated extension part can be locked in height. Multi-stage hydraulic cylinders, each beam with cardanic suspension Incl. outriggers - adjustable - with bolt safety device underneath the loading area5-fold control block for operating the sloping loading device and for folding device sliding roof.1 set of boiler floor holder with height-adjustable support bolts for different boiler floor diameters, incl. shelf.1 piece of stop protection for sloping plate - for securing to the front! Axles + suspension SAF disc brake axles Offset axle spacing mm Air suspension Brake system 2-line compressed air brake system Aluminum air reservoir Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS make Wabco, electronic brake system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift & lower valve + auto-reset function Vehicle - driving stability system Wheels and tires 435/50 R 19.5, manufacturer's choice Factory silver steel rims, manufacturer's choice Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 additional LED work light(s) at the rear, switched via reversing light 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, detachable with plug 1 rotating beacon with holder, detachable Floor Screen printing plates approx. 3

Condition: new, machine/vehicle number: 2b58968e34fac93b429a256e9, empty load weight: 5 kg, maximum load weight: 12 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support Wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Quarter-shell mudguards in front of 1st axle Spare wheel holder for 1 electric wheel, with wheel mounting kit Spare wheel, same make as basic tires, steel rim Plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Low loader lashing eyes 3 pairs of lashing points, each 10 tons, integrated in the floor at the front 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x according to the rest of the neck area, distributed between them, spacing not greater than 1200 mm 1 x rear bevel 5 pairs of ring lashing eyes embedded in the outer frame, 5 tons each (can be converted to stake pockets) Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Bsdsi Ri Nxspfx Abbslc Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cableVoltage converter for 12/24 volt operationNote! A 7-pin 12 volt socket is required on the tractor/tractor! (Required in conjunction with electrical voltage converter!) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white/red rear lane departure lights 2 white position lights at the front Additional LED work light(s) at the rear, switched via reversing light 2 x 7-pin interchangeable plugs at the front, with connecting cable1 x 7-pin agricultural plugVoltage converter 12/24 volt (only for electrics, not for ABS/EBS) Floor Front area steel floor, then with 70 mm softwood floor, steel/ checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions A special permit is required for axle loads of 10,000 kg. The permit must be applied for individually in each federal state; the legislator does not have to give an approval for 20 t GG. Customer risk. Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Drawbar Galvanized or black, manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: used, Year of construction: 2016, operating hours: 2,500 h, Single-sided edge banding machine for processing straight workpiece edges and for applying and further processing various edge materials in longitudinal and cross feed. OVERVIEW OF THE AGGREGATE CONFIGURATION: - Infeed fence extension by 300 mm with additional unit for laminate overhang - JOINTER UNIT 2 x 2.2 kW 200 Hz - GLUING UNIT A12 with automatic edge feed – APPLICATION UNIT QA 65 N EVA - TRIMMING UNIT BEVEL/STRAIGHT 2 x 0.35 kW Bsdsx S Nc Espfx Abbolc - PNEUMATIC ADJUSTMENT TRIMMING BEVEL/STRAIGHT - PNEUMATIC 2-POINT ADJUSTMENT TRIMMING - Multi-stage milling unit MS40 2 x 0.55 kW with opposed rotation and axis adjustment – with PNEUMATIC 2-POINT ADJUSTMENT of tracing rollers (flush and radius/bevel milling) - MULTIFUNCTION FORM MILLING UNIT 2 x 0.4 kW - MULTISTAGE SCRAPING UNIT MZ 40 - PNEUMATIC SCRAPER ADJUSTMENT - GLUE JOINT SCRAPER - BUFFING UNIT - SEPARATING AGENT SPRAY UNIT WORKPIECE - Glide agent spray unit - CLEANING AGENT SPRAY UNIT WORKPIECE - POWERTOUCH control system

Condition: excellent (used), Year of construction: 2010, Single-sided edge banding machine for processing straight workpiece edges as well as applying and post-processing various edge materials in both longitudinal and transverse feed directions. OVERVIEW OF THE EQUIPMENT CONFIGURATION: - POWER CONTROL PC 20+ electronic control - PU upper pressure rollers instead of rubber rollers Blsdpfx Absx S I Iyobsc - Workpiece gap optimization - Infeed fence extension by 300 mm with additional device for laminate overhang - JOINTING MILLING UNIT 2 x 2.2 kW 200 Hz - GLUING UNIT A12 with automatic edge feeding – Quickmelt application unit – Standard application unit interchangeable for PU glue - Pressure zone with motorized adjustment - END TRIMMING UNIT BEVEL/STRAIGHT 2 x 0.35 kW - PNEUMATIC ADJUSTMENT END TRIMMING BEVEL/STRAIGHT - PNEUMATIC 2-POINT ADJUSTMENT END TRIMMING - PRE-MILLING UNIT 2 x 0.55 kW counter-rotating – with PNEUMATIC 2-POINT ADJUSTMENT (flush and radius/chamfer milling) – Program control for side tracing rollers stepless and edge thickness – Multi-roller tracing - MULTIFUNCTION PROFILE MILLING UNIT 2 x 0.4 kW with exchange system and quick-change heads - PROFILE SCRAPER WITH QUICK-CHANGE HEADS - Special tracing for profile scraper - PNEUMATIC ADJUSTMENT SCRAPER - GLUE JOINT SCRAPER - POLISHING UNIT - RELEASE AGENT SPRAY UNIT WORKPIECE - CLEANING AGENT SPRAY UNIT WORKPIECE

Condition: used, functionality: fully functional, Year of construction: 2019, laser hours: 5,780 h, laser power: 4,000 W, TRULASER TUBE 7000 FIBER 4kW Bljdpfoyalb Esx Abbsc Year of manufacture: 07/2019 Laser power: 4kW fiber Laser on: 5780 h (!) Technical information: - Max. outside diameter: 254 mm - Loading and unloading - Loading with LoadMaster Tube: 6,5m / Automatic unolading: 4,5m - RapidCut  Use of a dynamic additional axis  More than fourfold accelerations possible Bevel cut technology package  Bevel cutting up to 45°  Contains electrically movable feed-through chuck - PierceLine  Optimized piercing process - Technology package for tapping • Additional machining processes such as flow drilling, tapping and twist drilling • NC controlled spindle with standard clamping system (standard interface HSK-A32) • The application and technology parameters of the tool adapter and tools should be requested from the respective supplier • 8-fold tool changer ...and many more options!

Condition: ready for operation (used), Year of construction: 2015, operating hours: 8,900 h, functionality: fully functional, travel distance X-axis: 4,000 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 178 mm, table length: 4,000 mm, table width: 2,000 mm, rapid traverse X-axis: 12,700 m/min, rapid traverse Y-axis: 12,700 m/min, rapid traverse Z-axis: 12,700 m/min, 💧 FLOW MACH 4 4020 – 5-Axis Waterjet Cutting Machine Year of manufacture: 2015 Working area: 4000 × 2000 mm (4 × 2 m) Cutting head: 5-axis (XD/dynamic bevel head) Pump hours: approx. 9,000 h Condition: Very good Service status: Regularly serviced, fully operational 🔧 Machine Overview The Flow Mach 4 4020 is a high-performance industrial waterjet cutting system tailored for demanding production environments. With its 5-axis XD cutting head, it enables dynamic bevel cutting, taper compensation, and precise 3D geometries—ideal for accuracy-driven and advanced applications. Despite its year of manufacture, the machine is in outstanding technical condition and has received professional, scheduled maintenance throughout its lifespan. All servicing has been performed on time, guaranteeing reliable, stable operation. ⚙️ Key Features - Working area: 4000 × 2000 mm - 5-axis XD cutting head – enables bevel cutting and taper compensation - Robust gantry construction for high precision - Industrial CNC control system - Capable of processing metals, stone, composites, glass, and technical materials Bljdoyaiqqjpfx Abbjc 💦 High-Pressure System - Pump operating time: approx. 9,000 hours - Pump and high-pressure components serviced in accordance with manufacturer guidelines - Stable pressure and consistent cutting performance ✅ Condition & Maintenance - Machine in very good overall condition - Continuously maintained during operation - No outstanding maintenance tasks - Ready for immediate integration into production 🎯 Summary This Flow Mach 4 4020 represents a well-maintained, proven industrial waterjet cutting solution with powerful 5-axis capability. It offers an excellent opportunity for companies seeking a dependable, high-precision system without the cost associated with new equipment. 📩 Contact us for further technical information, additional photos, or a customized commercial quotation. Included equipment: - Abrasive delivery system - Special tool for pump cylinder disassembly (FLOW hydraulic wrench) - Various spare parts The machine is fully functional, features low operating hours, and is immediately ready for use. It is the ideal solution for organizations seeking a reliable, large-format waterjet cutting system—including all essential accessories.

Year of construction: 1998, condition: good (used), Manufacturer unknown Year of manufacture ?? TRAV H/ 2830 The Aro Corporation Mod.78051BSN Blsdjf Axilepfx Abbsc Technical data: Compressed air driven for internal milling 50-225mm Accessories as shown

Condition: new, Table length: 2000 mm Table width: 1000 mm Table height: 200 mm Bore diameter: 28 mm Bore grid pattern: 100 x 100 mm Material thickness: approx. 24.5 - 27 mm Height of side panel: 200 mm Bledpfx Absxqy Imjbsc Working height: 850 mm Weight: 850 kg Product description: Siegmund Retro Special Offer incl. accessories: Welding table as it was 25 years ago, now also with plasma nitriding and modern table legs. - High-quality steel S355J2+N with plasma nitriding - Diagonal grid bore holes in side panels - Corners, edges, and bores beveled at 45° - Rib-reinforced construction - Incl. basic foot set (working height 850 mm) Accessories: - 6 x Professional screw clamps, nitrided - 12 x Quick-release bolts, double blackened, without slot - 8 x Universal stop 225 L, nitrided - 2 x Clamping and stop angle 175 L, nitrided - 2 x Clamping and stop angle 500 G, nitrided - 1 x Accessories set - Eccentric stop Ø 60 with M10 thread, nitrided - Hexagon key size 6 - Brush Ø 30 with protective cap - CleanBasic 1 liter in spray bottle - Anti-spatter 1 liter in spray bottle - Torch holder, blackened

Condition: new, empty load weight: 12,040 kg, maximum load weight: 71,000 kg, axle configuration: > 3 axles, first registration: 06/2025, suspension: air, load capacity: 58,960 kg, • 24V hydraulic power pack • Width extensions • Loading platform 8.90 m • Gooseneck 3.45 m, straight section • Width from 2.53 to 3.00 m • Deck height 0.90 m • Beveled rear section • Hydraulic ramps 3 m x 0.90 m • 14 lashing rings • Coupling height 1350 mm • Smartboard • LED lights • 1st axle liftable • 3rd and 4th axle self-steering • Drum brakes • Convoy kit • Length 12.65 m Bodpjx U E A Hefx Abbelc

Condition: used, functionality: fully functional, total length: 500 mm, total width: 440 mm, total height: 230 mm, overall weight: 26 kg, power: 1.69 kW (2.30 HP), input frequency: 50 Hz, input voltage: 400 V, type of input current: three-phase, Edge Milling Machine for Metal Brand: Marpol Rasant Suitable for deburring and beveling metals (e.g., steel, aluminum, brass), plastics, etc. Used, fully functional Bsdpex U D Afefx Abbjlc Bevel angle: 45° Continuously adjustable bevel Maximum bevel: 8 mm x 45° Cutter equipped with carbide indexable inserts Guide rail length: 400 mm 2-speed motor, Speeds: Level 1: 1420 rpm Level 2: 2840 rpm Motor power: 1.7/2.3 HP Connection: 400 V, 3-phase Weight: 26 kg Required space (L x W x H): 500 x 440 x 230 mm The machine can be inspected and tested under power. The machine is being sold due to the upcoming closure of the business (retirement). We also have further offers online.

Condition: new, diameter -- mm workpiece length -- mm work piece width 0 - 20 mm speeds 2850 U/min range of angles 0 - 60 (stufenlos) ° weight of the machine ca. 19,5 kg Bledpfx Aoppgcvebbjc Maximum chamfer width 20 mm + face machining Designed for chamfering and deburring straight edges, for the so-called FACING - removing an unwanted layer of material on the Front side of the workpiece, which is created, for example, by flame cutting a sheet metal. Specially developed for the production of visible chamfers and weld preparations. Powerful electric drive for extreme Charges. * High performance motor * stepless adjustment of the working angle in the range of 0° - 60° * FACING - Edge processing at an angle of 0° to remove unwanted ones Layers of material after flame cutting * The unique mechanical scale to adjust the bevel width for higher precision * A very compact and ergonomic design for high work productivity * Circumferential protective frame against damage and versatile grip options * With the appropriate accessories, pipes from D= 150 mm can also be processed * Additional adjustable handle - Chamfer width (hypotenuse): 0 - 20 mm = 400 Mpa / 0 - 16 mm = 400 Mpa - Motor: 1100W

Condition: new, diameter -- mm work piece width -- mm workpiece length -- mm Chamfering system UZ12 ULTRALIGHT - KIT 30° + 45° Maximum bevel width 12 mm with automatic feed The UZ12 ULTRALIGHT is one of the lightest automatic beveling machines advance in the market. Thanks to its compact size and light weight it is not only suitable for workshops, but also for assemblies. The Machine is equipped with the automatic feed and therefore does this Working with the UZ12 ULTRALIGHT very comfortably. * For conventional steel (up to 600 MPA/87022 PSI strength), Brass, copper and aluminum materials * For chamfering workpieces with the minimum dimensions of 65 x 60 x 3 mm * Application range of sheet thickness 3 - 35 mm * Beveling of pipes from an inner diameter of 95 mm * Variable setting of the desired bevel using an exchangeable holder kit for any given angle * Double-sided bevel (X, K) with no material handling * Silent working * Equipped with an automatic feed * Stationary or mobile use * The machine works with large workpieces without any support Bledpfx Aor I E Exjbbec a speed of 1.8m/min * Smaller workpieces are placed directly in the machine * Lightweight and compact design, handleable by one operator * Motor thermal protection - Max. bevel width (hypotenuse): 12 mm - Bevel angle: 30° / 45° / 22.5° / 37.5° / 50° (replaceable KIT) - Area of application sheet thickness: 3 - 35 mm - Motor: 400W - Feed speed: 1.8 m/min - Dimension: 470 x 294 x 523 mm We can also offer you an optional 3D manipulator (mobile) for this device on

Condition: new, diameter -- mm workpiece length -- mm work piece width 18 mm range of angles 15° - 50° ° weight of the machine ca. 110 kg Chamfering system UZ18 HARDWORKER Bljdpsk Egrtefx Abbec Maximum bevel width 18 mm with automatic feed The UZ18 Hardworker machine is one of the most powerful automatic feed beveling machines on the market. It is not only suitable for workshops, but also for on- site assembly. The machine has a stepless working angle adjustment system. Thanks to the special design of the drive system, the UZ18 Hardworker is also suitable for harder materials. The machine is equipped with the automatic feed. Working with UZ18 Hardworker is therefore very convenient. *For conventional steel (up to 600 MPA/87022 PSI strength), brass, copper and aluminum materials * For chamfering workpieces with the minimum dimensions of 70 x 150 x 6 mm * Application range of sheet thickness 6 - 40 mm * The bevel angle can be easily adjusted continuously from 15° to 50° without replacing any part * Double-sided bevel (X, K) with no material handling * Easy connection to 3D manipulator for easier operation and handling * Silent working * Equipped with automatic feeder * Stationary or mobile use * The machine works with large workpieces without any support at a speed of 1.9 m/min * Smaller workpieces are placed directly in the machine - Max. bevel width (hypotenuse): 18 mm - Infinitely adjustable angle: 15° - 50° - Area of application sheet thickness: 6 - 40 mm - Motor: 750W - Feed speed: 1.9 m/min - Weight: 110kg - Dimension: 438 x 719 x 644 mm We are happy to offer you an optional 3D manipulator (mobile) for this device on

Condition: new, diameter -- mm workpiece length -- mm work piece width 15 mm range of angles 15-50 ° plate thickness 6-40 mm total power requirement 1,5 kW Feed speed 3,5 m/min. dimensions 530 x 395 x 860 mm weight of the machine ca. 94 kg The UZ15 RAPID machine is one of the fastest beveling machines with automatic feed on the market. It is not only suitable for workshops, but also for assembly work. It has a stepless Bevel angle adjustment system. Also, the machine with an automatic feed equipped. Working with the UZ15 Rapid is therefore very convenient. - For conventional steel (up to a strength of 600 MPA/ 87022PSI), brass, copper and aluminum materials - For chamfering workpieces with the minimum dimensions of 70 x 150 x 6 mm - Application range of sheet thickness 6 - 40 mm - The bevel angle can be easily adjusted from 15° to 50° continuously without that a part needs to be replaced - Double-sided bevel (X, K) without material handling - Easy connection to the 3D manipulator for easier operation and Bodpek Uqhaefx Abbslc handling - Silent working - Equipped with automatic feeder - Stationary or mobile use - The machine works with large workpieces without any support a speed of 3.5m/min - Smaller workpieces are placed directly in the machine - Reduced price when purchasing UZ15 RAPID together with the 3D manipulator

Condition: new, diameter -- mm workpiece length -- mm work piece width 0 - 3 mm speeds 3600 U/min range of angles 30 - 60 (stufenlos) ° weight of the machine ca. 31 kg dimensions of the machine ca. 530 x 420 x 410 mm Maximum bevel width of 3 mm - Mechanically adjustable bevel angle Designed for deburring and chamfering steel parts and workpieces. Processing of different materials. Solid and stable machine construction. Bodpfx Aoppgcrebbelc * Scale for setting the processing depth * Security cover * Adjustable processing angle * For steel, stainless steel, aluminum and other materials * Precise, massive and overlong mechanical guide - Number of indexable inserts: 5 pieces (four-sided) - Feed: manual

Condition: new, diameter -- mm workpiece length -- mm work piece width 12 mm range of angles 30/45/22,5/37,5/50 ° weight of the machine ca. 30 kg Chamfering system UZ12 ULTRALIGHT - KIT 30° + 45° Maximum bevel width 12 mm with automatic feed The UZ12 ULTRALIGHT is one of the lightest automatic beveling machines advance in the market. Thanks to its compact size and light weight it is not only suitable for workshops, but also for assemblies. The Machine is equipped with the automatic feed and therefore does this Working with the UZ12 ULTRALIGHT very comfortably. * For conventional steel (up to 600 MPA/87022 PSI strength), Brass, copper and aluminum materials * For chamfering workpieces with the minimum dimensions of 65 x 60 x 3 mm * Application range of sheet thickness 3 - 35 mm * Beveling of pipes from an inner diameter of 95 mm * Variable setting of the desired bevel using an exchangeable holder kit for any given angle * Double-sided bevel (X, K) with no material handling * Silent working * Equipped with an automatic feed * Stationary or mobile use * The machine works with large workpieces without any support a speed of 1.8m/min * Smaller workpieces are placed directly in the machine * Lightweight and compact design, handleable by one operator * Motor thermal protection - Max. bevel width (hypotenuse): 12 mm - Bevel angle: 30° / 45° / 22.5° / 37.5° / 50° (replaceable KIT) - Area of application sheet thickness: 3 - 35 mm Bsdpfsppgcyex Abbolc - Motor: 400W - Feed speed: 1.8 m/min - Dimension: 470 x 294 x 523 mm We can also offer you an optional 3D manipulator (mobile) for this device on

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears Blsdsxazpqopfx Abbjc -Manufacturer: Poggi, gearboxes, bevel gears -Shafts: Ø 24 x 50 mm -Number: 3x gearbox available -Price: per piece -Dimensions: 250/250/H86 mm -Weight: 4.9 kg/piece

Condition: good (used), Gearboxes, spur gears, angle gears, worm gears, bevel gears Blsdpfsxaz Rzex Abbsc -Manufacturer: Marzorati, gearbox type A 150 with magnetic filter -Shafts: Ø 32 x 45 mm -Dimensions: 310/275/H200 mm -Weight: 19.6 kg