Low loader semitrailer

FAYMONVILLE Multimax Satteltieflader - hydr. gelenkt

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle fleet, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment. Full equipment details available upon request. Lhsdpfx Asyhkrfohvsd GOOSENECK: * Gooseneck in SNT design for optimization of loading platform length, approx. 3,700 mm long, with rear chamfer approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Plug-in steel front wall, approx. 400 mm high * ASPÖCK UNIBOX at the front connection rail with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, except hydraulic winches * On the gooseneck: 1 pair of plug-in aluminum side walls, approx. 400 mm high, anodized finish * On the gooseneck: 1 plug-in aluminum rear wall, approx. 400 mm high, anodized finish * Gooseneck covered with approx. 40 mm thick hardwood, king pin area with checker plate * 2" king pin LOADING AREA: * Extendable loading platform, approx. 8,800 mm long, with rear chamfer approx. 500 mm x 10° * A depression in the platform and chamfer to take up excavator dipper sticks, approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system according to ECE R 141. Data transmission to the truck via standard EBS interface in line with ISO 11992. For correct display, the truck must be able to transmit and display this data. * TPMS tire pressure sensors mounted on all wheels * BPW axles and suspension, 1st axle steered, all other axles hydro-mechanically forced-steered * 1st axle with electromagnetic reverse lock, activated by reverse gear and manually * Technical axle load: 12,000 kg each * Air suspension with lift and lower valve * Axle tools * Mechanical landing legs with 2-speed gearbox and crank, JOST Modul B, static test load = approx. 50,000 kg * 245/70 R 17.5 3PMSF twin tires. Brand at our discretion. Load index 143/141J (146/146F) * Loading area with continuous (between the axles interrupted) 50 mm thick hardwood floor (provides increased coefficient of friction) * Platform locked using welded-on conical locking profiles, every approx. 250 mm; includes pre-tensioning plate * 1 intermediate platform, approx. 300 mm wide, for large-diameter sliding tube * Intermediate platform with recessed loading area and extendable suspension bars for aluminum bridging elements * 1 pair of lashing rings on the front cross-member (LC 10,000 daN) * 8 pairs of recessed lashing rings in the outer frame of the loading area, fold-out to the outside (LC 10,000 daN) * Extendable (galvanized) platform wideners, approx. 230 mm each side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm in front of the axles, fully open to the gooseneck cross-member, approx. 700 x 410 mm (W x D) * ALU covers for the wheel recesses that can also be used as bridging elements for the extension OR as platform widening planks (if the vehicle is equipped with extendable wideners) * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * 1 pair of mechanical rear supports * Steering from front and rear via cable remote control, with single-track control of the axles HYDRAULIC LOADING RAMPS: * DR-15/60-900-4350-KG-HV-M: One pair of two-piece steel ramps, approx. 4,350 mm long and approx. 900 mm wide

Year of construction: 2005, condition: used, Item: AV-1832-Vertical-Tank140m3 Lhsdoh A H E Eepfx Ahvsd Vertical Silos Tanks capacity 140.000 L Exterior dimensions: Dia Ø 3500 mm Total H 16750 mm. Vertical stainless steel tanks - 6 pcs. Standing on 4 legs. Klóper bottom with 4" outlet. Klóper top with ventilation. AISI 304

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Ledpfx Ahorgzv Novohd Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish Lodjtx Nwnspfx Ahvohd * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Year of construction: 2022, condition: new, The fabric filter unit consists of one or more insulated compartments containing rows of fabric bags in the shape of round, flat or shaped tubes, or pleated cartridges. The particles contained in the exhausted air move along the surface of the bags, then radially through the fabric. The particles are retained on the upstream face of the bags and the clean gas stream is discharged to the atmosphere. The filter is operated cyclically, alternating with relatively long filtering periods and short cleaning periods. During cleaning, the dust that has accumulated in the bags is removed. Fabric filters collect particles ranging in size from submicron to several hundred microns in diameter with efficiencies generally greater than 99 or 99.9 percent. The layer of dust, or cake of dust, collected on the fabric is primarily responsible for such high efficiency. The cake is a barrier with tortuous pores that trap particles. Lhodpfxjibd Aze Ahvod

Condition: ready for operation (used), The subject of my auction is a Visser type KB belt conveyor Lhodjwu Hgaspfx Ahvsd Possibility of transport.