Used other horizontal machining centers for sale (62)

Condition: used, Year of construction: 2022, machine/vehicle number: YAA7159, Travel ranges (X/Y/Z): 600/400/500 mm, with a double pallet table, spindle speed: 12,000 rpm, machine weight: 6,600 kg, chip conveyor, band filter system, MITSUBISHI ELECTRIC M80 control system, HABOR cooling system, 30-position tool changer. Rodpfozhaxyox Amyecd

Condition: used, Year of construction: 2016, Makino A51NX in very good condition, including a new ATC tool changer and Cubes. Approx. 11,000 hours of cutting time. Capacity & Travels: Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Workpiece: ∅ 630 mm × 900 mm Max. Payload Capacity: 400 kg Spindle: Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Motion & Feed Rates: Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cutting Feedrate: 50,000 mm/min Rjdpjzg N E Hefx Amyocd Axis Acceleration: 1G B-Axis Indexing: Full 4th axis, Direct Drive (0.001-degree increments) Tooling: ATC (Automatic Tool Changer) Capacity: 60 tools Tool-to-Tool Time: 0.9 seconds Max. Tool Diameter / Weight: 170 mm / 12 kg 04003 HSK-A63 Spindle – Replaces the standard ISO50 interface. Features a double taper, full face contact, and hollow shank interface. Tool clamping force is higher than 44kN; HSK tool holders are required. 14017 HSK holders for 60 Tool ATC 26001 Moire Scale Feedback X, Y, Z-Axis Increments 0.05µm, positioning tolerance Tp = 0.006mm (ISO 230-2). 29006 Through Spindle Coolant 3.0MPa – Provides TSC flow of 30 l/min at 3.0MPa, replacing the standard 1.5MPa. Air through the spindle is possible. The pressure data refers to the output flange of the pump. 29009 Flow Switch for Through Spindle Coolant – Monitors through-spindle coolant flow. The machine will feed hold if the flow is below a preset level. Note: Recommended option for filtration systems to prevent tool damage. 31002 Air curtain for splash guard window – Located in the middle of the operator-side window, this air curtain prevents chips and coolant from obstructing the view. 37000 Broken tool sensor outside machining area (BTS) – Tool breakage detection for centric tools (tool diameter 1-40mm, tool length 65 - 430mm). Length measurement is performed using a movable probe. The measurement takes place in the ready position for a tool change, outside the machining area. Accuracy ± 2mm. If there is a difference between the measurement before and after machining, an alarm is triggered automatically. 37101L Automatic Workpiece Measuring Device (RENISHAW OMP60) – Three-coordinate measuring probe from RENISHAW with automatic coordinate correction. The signal is transmitted via infrared. Tolerance approx. 0.005mm. 14 automatic measurement cycles are available as pre-programmed cycles in the program memory. Note: requires 13m. Control Options: 60001 Automatic Corner Override (G62) – Automatically decelerates the cutter at a corner depending on the corner angle, in order to maintain the cutting rate per unit time. 62007 Run hour and parts quantity display. 63034 DATA CENTER Storage Type B (total: 800MB) – Communication card with internal 800MB removable flash RAM card used for storing and executing NC data (of subprograms) for high-speed, high-definition finishing and supporting SGI capabilities. CNC programs can be transferred to and from a CAD/CAM system from the operator's pendant by FTP get and put commands over an Ethernet cable. 66003 Additional 48 Work Offsets (G54.1 P1-P48) – Allows for 48 work coordinate systems, simplifying multiple part fixtures. 68010 600 Macro Common Variables – Variable numbers 100-199 are reset and cleared when the power is turned off, while 500-999 are permanent. Pallet Size: 400 × 400 mm X-Axis Travel: 560 mm Y & Z-Axis Travel: 640 mm Max. Payload Capacity: 400 kg Spindle Speed: 15,000 RPM Spindle Taper: HSK-A63 Rapid Traverse Rate: 60,000 mm/min (1,968 ipm) Cut...

Condition: used, Year of construction: 2010, operating hours: 2,000 h, functionality: fully functional, travel distance X-axis: 8,500 mm, travel distance Y-axis: 480 mm, travel distance Z-axis: 320 mm, nominal power (apparent): 8 kVA, workpiece length (max.): 8,500 mm, total height: 3,100 mm, total length: 11,500 mm, total width: 3,000 mm, rotational speed (max.): 15,000 rpm, overall weight: 6,000 kg, spindle speed (min.): 15,000 rpm, spindle motor power: 5,500 W, input voltage: 400 V, type of input current: three-phase, Equipment: documentation/manual, Elumatec SBZ 130 CNC 3-axis steel processing center, TOP condition Processes steel, stainless steel, aluminum, PVC, etc. The machine can mill, drill, tap, cut, and notch. All machining operations are performed while the profile is stationary. 8-position tool changer on a turret. Max. milling cutter diameter: 80 mm Max. disc cutter diameter: 200 mm Tools and accessories, including special wrenches, as shown in the picture. Tool holder: BT 30 Max. machining length: 850 cm, with stringer-side machining: 838 cm, y-axis: 48 cm, z-axis: 320 cm Year of manufacture: 2010, spindle speed: 15,000 rpm, spindle power: 5.5 kW Rcsdpfx Ajziy Idjmyed Weight: approx. 6 tons. Includes laser and partition, protective mat, machining accuracy: x-axis, y-axis, z-axis +/- 0.1 mm Air consumption: approx. 75 liters, with spray nozzles. Inspection is possible by appointment. The machine is located in 91629 Weihenzell.

Condition: used, Year of construction: 2012, operating hours: 37,500 h, machine/vehicle number: IntNr231616, Rcodpfx Aezggfqomyjd

Condition: used, Year of construction: 1991, KODIA Machining Center Rjdjupkifopfx Amyecd Model: B-500 Year: 1998 10kW

Condition: repair required (used), Year of construction: 2008, functionality: not functional, machine/vehicle number: B-7969, Technical characteristics: # Machining Workspace: X 800 mm; Y 400 mm; Height from table surface to floor: 850 mm (max load 450 kg) # Number of T-slots: 3 / Distance between T-slots: 125 mm / T-slot width: 18 mm # Axis description: 3 LINEAR AXES (X, Y, Z) / 4th Axis # Rapid traverse: X, Y, Z - 30 m/min # Travels: Longitudinal (X-axis) 600 mm, Cross (Y-axis) 400 mm, Vertical (Z-axis) 510 mm Redpfxsxxvtuo Amyscd Headstock capabilities: # Max. distance from spindle to table: 650 mm # Spindle nose: ISO7388 (with internal coolant supply), Tool holder size: 40 # Spindle speed range (standard): 100–14,000 rpm, Max. torque / at 330 rpm: 63.7/89.4 Nm Automatic tool changer: # Number of tools: 20, Selection system: sequential/random, Max. diameter (adjacent tool): 85 mm, Max. diameter (non-adjacent tool): 135 mm, Max. tool length: 300 mm, Max. tool weight: 6.5 kg # Tool change time: 3 s Electrical connection: # Voltage: 3x400V/50Hz # Installed power: approx. 30 kVA Dimensions: # Floor space required: approx. L 2.1 x W 3.5 x H 3 m # Weight: approx. 4,200 kg Equipment includes: # CNC control: GE Fanuc Series 31i MODEL A # Chip conveyor # Lubrication system # Electrical cooling cabinet # Spindle cooling system # Documentation: Electronic available / printed manual not available Machine status: NOT WORKING # 4th axis broken – repairable – dismantled from machine # Tool changer broken – repairable – dismantled from machine # Hydraulic pump broken – requires complete replacement

Condition: repair required (used), Year of construction: 2012, functionality: not functional, machine/vehicle number: 2560001, Technical specifications: # Machining workspace: X 600 mm; Y 525(890) mm; Z 400 mm # Axis configuration: 3 linear axes (X, Y, Z) + 1 rotary axis (A, rotary table) and 2 rotary axes (C, indexer head) with direct angular measurement system, 50 rpm, accuracy +/- 5 arcseconds # Maximum clamping/part dimensions: Ø 600 x 1420 mm; max weight 600 kg # Rapid traverse speeds: X/Y/Z 50/60/50 m/min; positioning accuracy Tp: 0.02 mm # Distance between spindles: 600 mm # Spindle speed: 1–6000 rpm # Spindle taper: DIN69893-HSK-A100 (with internal coolant supply) # Automatic tool changer: 2 x 20 tools, average chip-to-chip time 4.25 s # Tool maximum: Ø75 mm / length max. 275 mm / 7.5 kg Electrical specifications: # Voltage: 3x400V/50Hz # Installed power: approx. 85 kVA / 125A Dimensions: # Installation space (W x H x L): approx. 5.8 x 3.3 x 5.05 m # Weight: approx. 10,500 kg Rodpfx Amjxxkd Ueyecd Equipment includes: # CNC control: Siemens 840D SL # Linear axis measuring devices: Heidenhain linear scales # Chip conveyor: Knoll Type 550 K-1 # Oil cooling system # High-pressure oil filtration system, up to 80 bar: Knoll KF200/1200 # Shaft, guideway, and electrical cabinet cooling systems # 2 oil lubrication circuits # Oil mist absorption/recovery system # Tool breakage and length measurement: Blum Novotec # Work spindle tool presence detection system Machine condition: NOT OPERATIONAL # Automatic operator doors # Tool magazine # Axis protection covers for work area # Z-axis ballscrew and # Z-axis linear guides # Hydraulic overheating # Hydraulic pump (250 bar)

Condition: repair required (used), Year of construction: 2016, functionality: not functional, machine/vehicle number: 2460061, Technical specifications: # Machining Workspace: X 300 mm; Y 500 (725) mm; Z 375 mm # Axis configuration: 3 linear axes (X, Y, Z) + 1 rotary table axis (A) + indexable dividing head with direct angular measurement system, max rotational speed 50 rpm, accuracy +/- 5 arcseconds # Max. clamping dimension/part: Ø 575 x 830 mm; max. weight 360 kg # Rapid traverse (X/Y/Z): 65/75/75 m/min; Positioning accuracy Tp: 0.008 mm # Distance between spindles: 300 mm # Spindle speed range: 1–17,500 rpm # Spindle interface: DIN69893-HSK-A63 (with internal coolant supply) # Automatic tool changer: 2x32 tools / average chip-to-chip time 2.5 s Rcedpfx Amsxw R Udjyjd # Max. tool Ø 75 mm / max. length 275 mm / max. weight 7.5 kg Electrical data: # Voltage: 3x400V/50Hz # Installed power: approx. 85 kVA / 125A Dimensions: # Required installation footprint: approx. 3.6 x 6 x 3.7 m # Weight: approx. 10,500 kg Equipment includes: # CNC control: Siemens 840D SL # Linear axis measuring system: Heidenhain linear scales # Chip extractor: Knoll Type 550 K-1 # Oil cooling unit # Spindle, guideways, and switchboard cooling system # 2 oil lubrication units # Oil mist extraction/recovery system: ELBARON Vario E2000 (2,000 m³/h) # Oil filtration system with paper filter, max. 80 bar: Knoll KF200/1200 # Fire suppression: Kraft & Bauer # Part presence monitoring P/Y: with low pressure air detectors # In-process measurement: Marposs T25 # Tool breakage monitoring & length measurement: inductive sensor # Tool holding confirmation in main spindle Machine status: NOT OPERATIONAL # Motorised loading/unloading door # Table A axis # Tool magazine chain # Euchner safety switch, loading door # 5 hydraulic switches (Parker) # 2 pneumatic pistons for tool magazine access # 2 pneumatic pistons for tool clamping # Complete hydraulic system # Hydraulic motor (motor can also be retrofitted) # Compressed air regulator # Chip conveyor/extractor – needs repair # Z-axis linear scale # X-axis linear scale # Numerical control flash card # 4 communication modules (Murr) # 1 of 2 spindles defective – replacement spindle available in stock

Condition: repair required (used), Year of construction: 2001, functionality: not functional, machine/vehicle number: 1640137, Technical characteristics: # Machining workspace: X 400 mm; Y 450 (700) mm; Z 400 mm # Axis configuration: 3 linear axes (X, Y, Z) + 2 twin horizontal spindles + 2 rotary tables A1/2 NC (33.3 rpm), with hydraulic clamping mounted on indexable rotary table A3 (0 to 180° in approx. 4 sec). # Rapid traverse speed: X, Y, Z 1–40,000 mm/min # Positioning accuracy Tp: 0.01 mm # Distance between spindles: 400 mm # Spindle speed: 50–12,500 rpm # Spindle taper: DIN69893-HSK-A63 (with internal coolant supply) # Automatic tool changer: 2x30 tool positions / chip-to-chip time 4.5 sec # Maximum tool diameter 75 mm / Maximum tool length 275 mm / 10 kg Electrical connection: # Voltage: 3x400V/50Hz # Installed power: approx. 68 kVA Rcodoxvyfvepfx Amyed Dimensions: # Installation footprint: approx. 6.35 x 4.5 x 4.2 m # Machine dimensions: approx. 4.6 x 3.0 x 3.0 m # Weight: approx. 13,800 kg Equipment includes: # CNC controller: Siemens 840C # Linear axis measuring system: Heidenhain linear scales # Chip conveyor: Knoll 400K-1/950 RSF100 # Oil cooling unit # Shaft, guideways, and electrical cabinet cooling system # 2 oil lubrication systems # Oil vapor extraction/recovery system # Tool presence detection system in spindle

Condition: ready for operation (used), Year of construction: 1999, spindle speed (max.): 10,000 rpm, number of axes: 4, This 4-axis HELLER MC 16-2 was manufactured in 1999. It features a Siemens control system, a robust tool magazine with 160 slots, and an HSK-63A tool holder. The spindle operates at a speed of 10,000 rpm, ideal for detailed machining tasks. If you are looking to get high-quality milling capabilities, consider the HELLER MC 16-2 machine we have for sale. Contact us for more information about this machine. • Control: Siemens Sinumerik 840D Rodpfsx D I Alsx Amyecd • Tool magazine: 160 • Tool holder type: HSK-63A

Condition: excellent (used), Year of construction: 2014, machine/vehicle number: 506093, ITALMAC Pegaso 5 Axis Centar Rcodpfx Ajtrvmvemyed

Condition: used, TECHNICAL DETAILS - Number of axes : 27 - Number of posts : 12 - Number of machining stations : 9 - Indexing time : 2 [sec] MACHINING UNIT - Designation : UV151-3 - Number of units : 1 - Travels on X/Y/Z axes : 110 / 150 /100 [mm] - Rapid traverse rate : 6500 [mm/min] - Resolution : 0.001 [mm] MACHINING UNIT - Designation : UV50-3 - Number of units : 8 - Travels on X/Y/Z axes : 40 / 120/ 100 [mm] - Rapid traverse rate : 6500 [mm/min] - Resolution : 0.001 [mm] SPINDLES - Spindle type : Electrobroche Ø38 * Number of spindles : 14 * Tool holder type : ISO10 Redpow Huhcsfx Amyjcd * Spindle speeds : 18 000 [rpm] * Spindle power : 0.25 [kW] - Spindle type : Electrobroche Ø38 * Number of spindles : 4 * Tool holder type : ISO10 * Spindle speeds : 9000 [rpm] * Spindle power : 0.25 [kW] * Spindle type : Electrobroche Ø120 - Number of spindles : 1 - Tool holder type : HSK40 * Spindle speeds : 8710 [rpm] * Spindle power : 3.8 [kW] * Spindle type : Electrobroche Ø38 - Number of spindles : 2 - Tool holder type : ISO10 * Spindle speeds : 9000 [rpm] * Spindle power : 0.25 [kW] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 10 [kW] WEIGHT & DIMENSIONS - Machine floor space : 4600 x 3600 [mm] - Machine height : 3200 [mm] - Machine weight : 13500 [kg] - Equipment EQUIPMENT - CNC : Siemens - Cooling unit - Coolant tank * with high-pressure pump - Chips conveyor - Oil mist extractor : ELBARON RON/A 120 - Loader - Fire-fighting device - Fitting

Condition: used, TECHNICAL DETAILS - Number of axes : 27 - Number of posts : 12 - Number of machining stations : 9 - Indexing time : 2 [sec] MACHINING UNIT Rjdpsv Rgy Hofx Amyecd - Designation : UV151-3 - Number of units : 1 - Travels on X/Y/Z axes : 110 / 150 / 135 [mm] - Rapid traverse rate : 6500 [mm/min] - Resolution : 0.001 [mm] MACHINING UNIT - Designation : UV50-3 - Number of units : 8 - Travels on X/Y/Z axes : 40 / 120 / 100 [mm] - Rapid traverse rate : 6500 [mm/min] - Resolution : 0.001 [mm] SPINDLES - Spindle type : Electrospindle Ø38 * Number of spindles : 14 * Tool holder type : ISO10 * Spindle speeds : 18.000 [rpm] * Spindle power : 0.25 [kW] - Spindle type : Electrospindle Ø38 * Number of spindles : 4 * Tool holder type : ISO10 * Spindle speeds : 9.000 [rpm] * Spindle power : 0.25 [kW] - Spindle type : Electrospindle Ø120 * Number of spindles : 1 * Tool holder type : HSK40 * Spindle speeds : 8.710 [rpm] * Spindle power : 3.8 [kW] - Spindle type : Electrospindle with gear reducer Ø38 * Number of spindles : 2 * Tool holder type : ISO10 * Spindle speeds : 9.000 [rpm] * Spindle power : 0.25 [kW] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 10 [kW] WEIGHT & DIMENSIONS - Machine floor space : 4600 x 3600 [mm] - Machine height : 3200 [mm] - Machine weight : 13500 [kg] EQUIPMENT - CNC : Siemens - Cooling unit - Coolant tank * with high-pressure pump - Chips conveyor - Oil mist extractor : ELBARON RON/A 120

Condition: used, TECHNICAL DETAILS - Number of axes : 27 - Number of posts : 12 - Number of machining stations : 9 - Indexing time : 2 [sec] MACHINING UNIT - Designation : UV151-3 - Number of units : 1 - Travels on X/Y/Z axes : 110 / 150 / 135 [mm] - Rapid traverse rate : 6500 [mm/min] - Resolution : 0.001 [mm] MACHINING UNIT - Designation : UV50-3 - Number of units : 8 - Travels on X/Y/Z axes : 40 / 120 / 100 [mm] - Rapid traverse rate : 6500 [mm/min] - Resolution : 0.001 [mm] SPINDLES - Spindle type : Electrospindle Ø38 * Number of spindles : 14 * Tool holder type : ISO10 * Spindle speeds : 18.000 [rpm] * Spindle power : 0.25 [kW] Rsdpfev Rgyyox Amyocd - Spindle type : Electrospindle Ø38 * Number of spindles : 4 * Tool holder type : ISO10 * Spindle speeds : 9.000 [rpm] * Spindle power : 0.25 [kW] - Spindle type : Electrospindle Ø120 * Number of spindles : 1 * Tool holder type : HSK40 * Spindle speeds : 8.710 [rpm] * Spindle power : 3.8 [kW] - Spindle type : Electrospindle with gear reducer Ø38 * Number of spindles : 2 * Tool holder type : ISO10 * Spindle speeds : 9.000 [rpm] * Spindle power : 0.25 [kW] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 10 [kW] WEIGHT & DIMENSIONS - Machine floor space : 4600 x 3600 [mm] - Machine height : 3200 [mm] - Machine weight : 13500 [kg] EQUIPMENT - CNC : Siemens - Cooling unit - Coolant tank * with high-pressure pump - Chips conveyor - Oil mist extractor : ELBARON RON/A 120

Condition: used, TECHNICAL DETAILS - Revolver head TRH308 with turret equipped as shown on the picture * Max. power : 12 [kW] Rjdpeuhbwvsfx Amyscd * Max. torque during machining : 250 [Nm] * Weight : 100 [kg]

Condition: used, TECHNICAL DETAILS - Number of axes : 48 - Number of posts : 16 - Number of units : - Number of possible horizontal units : 16 - Number of possible vertical units : 7 - Max. diameter : 45 [mm] - Max. part width : 150 [mm] - Basis unit GM50/150 : * Stroke Z : 150 [mm] * Spindle power : 5 [kW] * Spindle speed : 0 - 8000 [Rpm] - Slide X/Y : * Strokes X : +/- 40 [mm] * Strokes Y : +/- 20 [mm] - Dimensions : 14000 x 4800 x 3000 [mm] - Weight : 13 [t] - Number of hours : 4283 [h] EQUIPMENT - Control CNC Bosch Rexroth INDRAMOTION MTX-L85 - Post 1 : * sawing unit 52/100 3 axes - Post 2 : * slide 50/150 (manual adjustment) ref. 22.10.002-1 * unit 50/150 ref 22.42.001-6 (1 axis) Rsdpfsu N Ivqsx Amyecd * coolant through spindle - Post 3 : * slide 50/150 (manual adjustment) ref. 22.10.002-1 * unit 50/150 ref 22.42.001-6 (1 axis) * coolant through spindle - Post 4 : * slide 50/150 (manual adjustment) ref. 22.10.002-1 * unit 50/150 ref 22.42.001-6 (1 axis) * coolant through spindle - Post 5 : * slide CNC 50/150 ref 22.10.001-4 (2 axes) * unit CNC 50/150 ref 22.42.001-6 (with CNC turning function) * coolant through spindle - Post 6 : * slide CNC 50/150 ref 22.10.001-4 (2 axes) * unit CNC 50/150 ref 22.42.001-6 (with CNC turning function) * coolant through spindle - Post 7 : * slide 50/150 manual adjustment ref 22.10.002.1 * unit recessing ref 22.42.041.1 - Post 8 : * slide CNC 50/150 ref 22.10.001.4 (2001) * unit CNC 50/150 ref 22.42.001.6 (with CNC turning function) - Post 9 : * slide CNC 50/150 ref 22.10.001.4 * recessing unit ref 22.42.039.2 - Post 10 : * slide 50/150 manual adjustment ref 22.10.002.1 * recessing unit ref 22.42.039.8 - Post 11 : * slide CNC 50/150 ref 22.10.001.4 * unit 50/150 ref 22.42.001.6 (CNC turning function) - Post 12 : * slide 50/150 ref 22.10.002.1 * recessing unit ref 22.42.041.1 - Post 13 : * slide CNC 50/150 ref 22.10.001.4 * recessing unit ref 22.42.041.1 - Post 14 : * slide CNC 50/150 ref 22.10.001.4 * unit CNC 50/150 ref 22.42.001.6 (turning function) - Post 15 : * slide CNC 50/150 ref 22.10.001.4 * unit CNC 50/150 ref 22.42.001.6 (turning function) * coolant through spindle - Post 16 : * slide CNC 50/150 ref 22.10.001.4 * unit CNC 50/150 ref 22.42.001.6 (turning function) * coolant through spindle - Bar feeder length 4 m - Coolant tank KNOLL (2000 Liters) with HP pump 60 [bars] - Chips conveyor

Condition: used, TECHNICAL DETAILS - Posts number : 16 - Indexing time : 0,7 [s] - Max. bar diameter : 32 [mm] - Clamping type : collet VB 32 - Max. part length : 150 [mm] - Max. number of horizontal units : 16 - Max. number of vertical units : 24 - Max. number of all units : 24 Rsdpfxsuhbwio Amyecd - Electrical supply : 400 [V] - Installed power : 40 [kW] - Dimensions : 9,8 x 4 x 2,9 [m] - Weight : 6 500 [kg] EQUIPMENT - CNC SIEMENS Sinumerik 805 - Bar feeder HYDROMAT - 2 turning units CNC 2 axes - Band part conveyor - Chip conveyor - Lubricating tank - Filtration

Condition: used, TECHNICAL DETAILS - Posts number : 12 - Table indexing : 12 x 30 [°] - Collet type : SCHAUBLIN W25 - Max. clamping diameter : 25 [mm] - Max. part length : 100 [mm] - Supply voltage : 3x 400 [V] - Installed power : 32 [kW] - Machine dimensions : 2700 x 2700 x 2500 [mm] - Weight : 4000 [kg] EQUIPMENT - CNC SIEMENS Sinumerik 805 - Bar feeder HYDROMAT 5.07.018-4, capacity 4200 mm - Post 1, bucking - Post 2, longitudinal drilling 30/60 - Post 3, longitudinal drilling 30/60 - Post 4, CNC turning 2 axes - Post 5, turnaround - Post 6, radial drilling 30/60 - Post 7, CNC turning 2 axes - Post 8, inclined drilling 30/60 Rsdpfx Aeuhbwcjmyjcd - Post 9, radial drilling 30/60 - Post 10, inclined drilling 20/50 - Post 11, radial drilling 20/50 - Post 12, longitudinal drilling 30/60 - Ejection between the posts 12 and 1 - Part band conveyor - Chip conveyor KNOLL 450 K-1/2000 - Lubrication tank KNOLL KTS-25-60-T - Pump HP : 40 [bar] - Filtration KNOLL VRF 500

Condition: excellent (used), 3-axis machining center Work area: 1350 x 2565 mm. Rjdezcpfajpfx Amyjcd Workpiece clamping via vacuum pump.

Condition: used, Year of construction: 2003, functionality: fully functional, HORIZONTAL MACHINING CENTER "FAMUP" MOD. MF 650 CNC FANUC SPINDLE HSK 63 15,000 RPM TRAVELS MM 700X660X550 PALLET MM 500X500 FULL ROTARY TABLE ATC 50 POSITIONS HIGH-PRESSURE COOLANT CHIP CONVEYOR Rcedpfjxwccmsx Amyed YEAR 2003

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, For technical data, see images.... Rcodoy Tl N Ropfx Amyed

Condition: like new (used), Year of construction: 2008, travel distance X-axis: 700 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 700 mm, feed rate X-axis: 60 m/min, feed rate Y-axis: 60 m/min, feed rate Z-axis: 60 m/min, nominal power (apparent): 68 kVA, controller manufacturer: HEIDENHAIN iTNC 530, workpiece height (max.): 1,000 mm, workpiece diameter (max.): 800 mm, workpiece weight (max.): 600 kg, total height: 2,547 mm, total length: 5,866 mm, total width: 4,196 mm, table width: 500 mm, table length: 500 mm, overall weight: 12,000 kg, spindle speed (max.): 18,000 rpm, spindle motor power: 34,000 W, number of slots in tool magazine: 120, Equipment: chip conveyor, documentation/manual, CNC controller: HEIDENHAIN iTNC 530 Axes: X-axis travel mm: 700 Y-axis travel mm: 700 Z-axis travel mm: 700 Distance spindle nose - table surface mm: 100 - 800 Rapid traverse m/min: 60 Acceleration in the axes m/s2: 6 / 6 / 5 Worktable: Number of pallets: 2 + 5 Table dimensions mm: 500 x 500 Maximum workpiece size (D x H) mm: 800 x 1.000 Max. workpiece weight kg: 600 T-Slot version: DIN 55201-A2 APC time s: 9,5 División estandar Grados: 360º (1º) Spindle: Spindle speed rpm: 18.000 Spindle drive power kW: 34 / 28 Spindle torque Nm: 110 Tool system: Tool holder: HSK-A63 Redpfx Aewhdhzomyecd Tool magazine slots: 120 Max. Tool Diameter: 80 Max. Tool Length mm: 550 Max tool weight kg: 12 Chip-to-chip time s: 2,9 Equipment: Electronic Handwheel Chip conveyor Rotating inspection windows Rinsing gun Signal lamp Tool breakage probe 3D quickSET Workarea light CE conformity Cooling device blowing air through spindle center, selectable via M-function MPC – Machine Protection Control Paper band filter Infrared Probe Heidenhain TS640 Blum laser tool measurement Taper clear brushes Blum laser NT Hybrid Round pallet Storage (RPS 5) Measuring probe Heidenhain TS 640 Production package Internal cooling supply 40 BAR Cooling: Cooling through the Spindle Center bar: 40 BAR Tank capacity: 980 High-pressure bar: 40 BAR Machine running times: Under power: 95.210 Operating Time: 44.971 Rated power kVA: 68 Basic machine dimensions / weight: Length mm: 5.866 Width mm: 4.196 Height mm: 2.547 Weight kg: 12.000.

Condition: used, Year of construction: 2011, Mazak HC Nexus 6000-II Mazatrol Matrix Nexus Year: December 2011 Pallet Size: 500mm x 500mm Movement: Max Workpiece: Ø 900 mm x 1000 mm Max Table Load: 1000 kg Rcsdjv Tvivjpfx Amysd Spindle Speed: 10,000 rpm (2 gears) Spindle Power: 30/37kW Spindle Taper: CAT 50 Rapid Traverse X/Y/Z: 60 m/min Tool Magazine: 80

Condition: used, Year of construction: 2011, Pallet: 500 x 500 mm X: 730 mm Y: 730 mm Z: 740 mm Maximum detail size: Ø 800 x 1000 mm Max load capacity: 700 kg Spindle speed: 12 000 r/min - High-torque Rjdpoy H Dnxjfx Amyjcd Spindle effect: 22/30 kW , 300 Nm (AC40HP) CAT 40 Tool changer: 40 positions Interface for coolant system Prepare for probe OMP60 Cromar conveyor Synchronised tapping G00 slope constant EIA EIA 3D COMP Scaling included loading of machine included tools and cubes Mazak HC Nexus 5000-II: LxWxH: 475 x 238 x 285 cm Pallet: 500 x 500 mm X: 730 mm Y: 730 mm Z: 740 mm Max load capacity: 700 kg Tool changer: 40 positions

Condition: used, Year of construction: 2004, Makino A66E with Fastems 10 pallet system built in container. Length of the working table 500.4 mm Width of the working table 500.4 mm Maximum table load 700 kg Antalet verktyg i magasinet 136 st Rcjdpfey D Sirex Amyjd Maximum spindle speed 14000 rpm Travel length X-axis (mechanical feed) 729 mm Travel length Y-axis (mechanical feed) 729 mm Travel length Z-axis (mechanical feed) 797.6 mm Maximum feed rate in X-axis 1250.1 mm/s Maximum feed rate in Y-axis 1250.1 mm/s Maximum feed rate in Z-axis 1250.1 mm/s