Used Drying Furnace for sale (3,146)

Year of construction: 2017, condition: good (used), functionality: fully functional, Furnace Housing Dimensions External dimensions: - approx. 3,800 x 4,300 x 2,200 mm Internal (usable) furnace dimensions: - approx. 2,440 x 1,400 x 1,200 mm Batch Load weight: - 9 boxes (net weight 50 kg/each) - approx. 250 kg material per box - stack arrangement 3x3 Performance Data - 1 gas recuperator burner - 160 kW rated heating capacity - Max. allowable chamber furnace temperature 720°C - Max. allowable post-combustion temperature 1,020°C - 1 temperature control zone Temperature Control Range - Chamber furnace 480°C – 700°C - Post-combustion 850°C – 1,000°C Supply Media - Natural gas L or H - Gas inlet pressure 80 mbar - Voltage 400 V - Frequency 50 Hz - Connected load 8 kVA - Compressed air 6 bar, dry, oil-free Dwedpexcybksfx Al Aec Material: e.g. brass or bronze

Condition: new, Year of construction: 2024, Drying and Burn-in Furnace TRO, Model I For drying racks with max. 50rods, useable size 60x90cm, outer dimensions: approx. 2290mm wide x 1390mm deep x 2230mm high, useable space: approx. 1400x1070x1660cm. Suitable for vaporisation of low amounts of solvent, authorised for inks and solvents up to hazard class A II, according to safety requirements DIN EN 1539. Equipped with control of the minimum exhaust volume and a heating system in regard to the exceedance of the max. temperature. Fixing and drying temperature: up to max. 180°C. Power connection: 400V/50Hz, 21kW, weight: approx. 650kg, varnishing: corps RAL 7035 (light grey), doors RAL 7037 (dust grey). Special varnishing upon request. Chamber dryer, all-steel construction, with good thermal insulation. Simple insertion of drying racks by means of easy-to-open wing doors. The air is sucked out of the drying chamber by ventilators, is blown through thermostat-controlled heating registers and re-fed temperature-controlled to the drying chamber. The solvents released during the drying process are dissipated from the exhaust side of the ventilator while supply air gets into the drying chamber. The horizontal air guide in the drying chamber guarantees an even temperature control. The required temperature can easile adjusted via actual and nominal value thermostat. Overheating protection by safety thermostat. Particularly suitable for fixing and drying of textile inks, flock glues as well as for burning-in of plate and aluminium signs up to 180°C. - Various drying racks for different applications available. - We recommend the installation of a gas warning unit. Delivery time 10-12 weeks. ATTENTION: Not permitted for solvents! Not permitted for foods! Dwodpfx Alod I T Exj Ajc

Condition: as good as new (ex-display), Vacuum drying cabinet Internal dimensions: 700 x 700 x 600 mm (depth) Heating output: 3 kW Temperature range: 1-120°C External dimensions: 1280 x 950 x 1280 mm Pressure range: Atmospheric pressure - 0 bar (not suitable for overpressure) A suitable vacuum pump will be supplied depending on the application. Dwedefbl T Nepfx Al Asc Power supply: 3-phase, N, PE, 400V, 50Hz, CEE plug The internal components can of course be completely removed!

Condition: like new (used), Year of construction: 2023, machine/vehicle number: SN432511, functionality: fully functional, power: 75 kW (101.97 HP), input voltage: 400 V, input current: 108 A, input frequency: 50 Hz, type of input current: three-phase, temperature: 1,340 °C, inner dimension length: 1,000 mm, inner dimension width: 800 mm, inner dimension height: 1,250 mm, total length: 1,800 mm, total width: 1,900 mm, total height: 2,500 mm, overall weight: 2,800 kg, number of chambers: 1, control type: PLC-controlled, actuation type: electric, Equipment: CE marking, documentation/manual, with 12 months warranty -Internal dimensions (w x d x h): 800 x 1000 x 1250 mm -External dimensions (w x d x h): 1790 x 1900 x 2500 mm Djdpszbr U Uefx Al Aowc -Control cabinet (w x d x h): 1200 x 500 x 2350 mm -Controller cabinet (w x d x h): 600 x 900 x 1850 mm -Capacity: 1000 liters -Maximum temperature: 1340 °C -Siemens PLC control system H1700 (100 programs, each with 20 segments) -Nabertherm NCC, computer-aided, extremely user-friendly control system, recording of all parameters. Recordings can be processed, supplemented with batch data, etc., and archived and printed. -Printer and UPS integrated in the controller cabinet -Automatically generated report after each heating cycle -Thyristor-controlled -2 opposing, lockable doors with safety interlock -5-sided heating -Manual air inlet damper -Motorized exhaust damper -Stainless steel exhaust hood with pipe connection flange -Calibrated control thermocouples for the three heating zones -Temperature accuracy: ± 15 °C from 500 to 850 °C, ± 10 °C above 850 °C, all values according to DIN 17052-1 in the empty working space, without recording -Separate control cabinet -Audible alarm and alarm light -Overtemperature limiter -Power: 75 kW -Oven weight approx. 2320 kg + control cabinet + controller cabinet -DGUV V3 test currently valid with report -Documentation, CE declaration, circuit diagrams The oven is in TOP condition. It has been used for approximately 10 months in a cleanroom for the production of implants and is of high quality (new price 100,000 EUR net) and absolutely clean. We would be happy to offer installation and commissioning as well as training for your employees. Please contact us! We offer new and used industrial furnaces. Inspection in our warehouse upon request! Chamber furnace, furnace, kilns, annealing furnace, firing furnace, hardening furnace, heat treatment furnace, tempering furnace, enameling furnace, drying oven, industrial furnace, ceramic furnace, tempering furnace, sintering furnace

Condition: excellent (used), Year of construction: 2015, machine/vehicle number: Drymex S 5, functionality: fully functional, operating hours: 8,286 h, Beautiful, robust, and excellently maintained drying system, consisting of 2 units, 1 large drying chamber made of stainless steel with a perforated sheet metal floor incl. piping and the Blue Evolution XL steam cleaning device from Beam. Ideal for gentle drying of food (herbs, tea, wheatgrass), low-temperature drying with electricity (below 40°C), for indoor use only. The individual segments of the perforated sheet metal floor can be opened individually (for cleaning). In top condition, very solidly built. Dimensions: Units - 1.95 x 1.25 x 2.00 m, Drying chamber: 7.40 x 2.67 x 2.50 m. Stainless steel: 1.4301 Dwedpoyffqqefx Al Ajc The entire system is very well maintained, still assembled, and fully operational. Can be inspected at any time while powered on. The drying chamber can also be divided and connected to one unit each. This will provide you with two identical dryers. Price negotiable.

Condition: used, Manufacturer: David + Baader, Kandel Type: 10880.3 Machine type: Industrial furnace / Chamber furnace / Heat treatment furnace For sale is a used industrial furnace from the manufacturer David + Baader Kandel, type 10880.3. The furnace is suitable for a wide range of applications in industry, trade, laboratories, and workshops and is ideal for heat treatment, drying, or annealing processes. Technical data Manufacturer: David + Baader Kandel Type: 10880.3 Design: Electric chamber furnace Condition: Used Further technical data available upon request or as per the nameplate Features and advantages Robust industrial design Uniform heat distribution Reliable temperature control Stable furnace chamber Suitable for continuous operation Proven German quality Possible applications Heat treatment of metal parts Annealing and tempering processes Drying processes Dwjdpfx Aloznv Dfe Ajc Laboratory and testing applications Research and development Workshop and production operations

Condition: refurbished (used), Year of construction: 2010, machine/vehicle number: SN214289, functionality: fully functional, Completely overhauled, electrical system renewed including conversion to thyristor technology, as well as installation of new controllers! -Maximum temperature 260°C -Capacity 9000 liters -Nabertherm controller P 300 (9 programs, each with 40 segments) -HAS (High-Accuracy System), a highly accurate system for temperature control and documentation -Double door -Internal dimensions W x D x H 1500 x 3000 x 2000 mm -External dimensions W x D x H 2400 x 3860 x 2830 mm -Temperature limit selector -Thermocouple type K -Signal column -Access ramp, oven with bottom insulation, high temperature uniformity -Circulation rate 18000 m³/h -Power 93 kW -Documentation, CE -Electrically tested and with current DGUV test report The oven is calibrated according to DIN 17052 as of February 2025. This standard ensures that the temperature throughout the oven chamber is within defined tolerances. Suitable for applications such as heat treatment of metals or in additive manufacturing (3D printing) when processes that comply with standards are required. Inspection can be arranged at our warehouse at any time. We offer new and used industrial ovens, which we can also modify and expand according to customer requirements. Djdpfxjyxl Epo Al Aswc Oven, furnaces, drying oven, industrial oven, drying cabinet, heat treatment oven, heat chamber, convection oven, chamber oven, heating oven, chamber convection oven, tempering oven, annealing oven, hardening oven.

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, New unit, in stock, immediately available -Volume 18,000 liters -Maximum temperature 350°C -Internal dimensions L x W x H 4100 x 2100 x 2100 mm -External dimensions (with rails) L 9970 x W 3060 x H (with lift-up door) 6110 mm -Control system Eurotherm Nanodac -Temperature stability (at rated temperature without load) ±5°C -Automatic inlet and outlet air dampers -Electric lift-up door -Electrically driven hearth carriage -Power 247 ± 9% kW -400 V, 50 Hz -Documentation, CE declaration We would be pleased to offer installation and commissioning, as well as training for your employees. Please contact us! We offer new and used industrial furnaces. Inspections in our warehouse are available upon request! Dodpfx Alsu Hma Nj Ajwc Furnace, kilns, annealing furnace, firing furnace, hardening furnace, heat treatment furnace, tempering furnace, enamelling furnace, drying oven, industrial furnace, heating chamber, heating oven, temperature oven, drying cabinet, chamber furnace, large-volume furnace, bogie hearth furnace, car hearth furnace, shuttle kiln, bogie hearth kiln.

Year of construction: 2020, condition: new, Kreuzmayr fruit drying cabinet OTS 4 drying surface 4m³ stainless-steel construction Dwodpfx Aoygm Isl Asc

Condition: used, functionality: limited functionality, Technical specifications Manufacturer: Stahl Type: 8220 Design: Industrial furnace / Chamber furnace Condition: Used Further technical data according to the nameplate Equipment Robust and durable construction Electric heating Temperature control for precise processes Good heat distribution in the working chamber Suitable for professional use Application areas Heat treatment of metal parts Annealing and tempering Drying processes Preheating of workpieces Laboratory and testing applications Research and development Unfortunately, 2 rotary knobs are broken, but the potentiometers still work. However, it is unclear what setting they correspond to. Dwsdpfxjznv Eio Al Aec This is more suitable for hobbyists.

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, New machine, immediately available, 12 months warranty -Internal dimensions (w x d x h): 1250 x 4000 x 1450 mm -External dimensions (w x d x h): 1900 x 4900 x 2500 mm -Power consumption: 240 kW -Current consumption: 350 Amperes -Maximum temperature: 1300 °C -Oven weight (approx.): 6000 kg -Control system: JUMO IMAGO 500 -Software packages: (OPCA & PCC) -Display unit: JUMO Logoscreen 601 -Includes: feedthrough hole and 6 additional slots for recording type K customer thermocouples -Multi-zone design (3 zones) -Switchgear with solid-state relays -Climate control for the switchgear -Automatic inlet and outlet dampers -Controlled cooling system (including frequency converter, controlled via the control system) -Electrically driven furnace car -Maximum load: 3.5 tons Dodpfx Aloy Avmlj Aswc -Swinging door -Documentation, CE declaration We would be happy to offer installation, commissioning, and training for your employees. Please contact us! We stock new and used industrial furnaces. Inspections in our warehouse are possible upon request. Furnace car oven, car hearth oven, furnaces, annealing furnace, firing furnace, hardening furnace, heat treatment furnace, oven, stress-relieving furnace, enamelling furnace, drying oven, industrial furnace, bogie hearth furnace, car hearth furnace, shuttle kiln, bogie hearth kiln

Condition: excellent (used), Year of construction: 2022, operating hours: 600 h, functionality: fully functional, machine/vehicle number: PO210417, total width: 4,600 mm, total length: 25,000 mm, total height: 3,000 mm, type of input current: three-phase, energy consumption: 1,700 kWh, input current: 2,230 A, The AG series of convection tempering furnaces with forced air circulation (Northglass fifth-generation furnaces, featuring proprietary focused convection technology) was developed to meet the growing customer demand for more efficient low-E glass tempering, improved product quality, and reduced energy consumption. The AG series furnace integrates the advantages of a four-convection furnace, primarily offering benefits in terms of higher productivity, superior product quality, and easier process control. The furnace consists of loading conveyors, a heating section, a convection system (upper and lower), a flat tempering/cooling section, and an unloading conveyor. The equipment package includes air ducts and a device control system. Max. working width: 2,850 mm. Max. loading length: 5,000 mm. Max. glass loading area: 2,850 x 5,000 mm (5-19 mm), 2,850 x 4,600 mm (4 mm). Upper fan convection: 6 fans x 4 kW, lower: 6 fans x 3 kW. Main technical data is attached in a PDF file. Dodpsz Dhm Ujfx Al Aowc

Year of construction: 2003, condition: used, functionality: fully functional, machine/vehicle number: HWO 1/9-5.2​, - The system is located at the Geberit Keramik GmbH site in Wesel. - The system, including the associated safety technology, performs technical flash firing and re-firing and is prepared for this purpose. - Maximum firing temperature [°C] = 1300 - Current operating temperature [°C] = 1238 - Number of burner groups = 10 - Number of burners = 38 - Number of kiln cars = 18 - Number of kiln cars in the kiln = 9 - Current firing cycle [h] = 17 - 23 - Gross energy consumption [kcal/kg] / [kWh/kg] = 785 / 0.912 - Specific energy consumption [kcal/kg] / [kWh/kg] = 1459 / 1.696 - Gas connection capacity [m³/h] = 770 - Usable waste heat [m³/h] = 4000 - Standard loading quantity [pieces] = 900-980 ceramic products Dimensions of the housing: - Length [m] = 14.4 - Width [m] = 6.4 - Height [m] = 5.7 - Volume density [m³] = 146.3 Dimensions of the kiln car: - Effective length [m] = 1.45 - Effective width [m] = 5.2 - Effective height [m] = 2.156 - Track gauge [m] = 1.5 (2x) Djdpfx Aezu Nvzsl Aswc Special features: In 2023, the kiln was completely overhauled and brought up to the latest state of the art. The following changes were made: - Renewal of the kiln roof: The fiber lining in the upper area was replaced with cordierite stones. - Renewal of the burners, including new nozzles, flame tubes and controllers. - Replacement of the media valves; installation of servo motors on the gas and air lines in front of the burners. - Installation of new software; the Simatec control panel was replaced – control is now exclusively via the PC. - Replacement of the O₂ control system; installation of a Zerox probe; installation of an O₂ analyzer for O₂ correction (to improve energy efficiency by approximately 12–14 %). - The system must be dismantled, packed and collected independently by the buyer.

Condition: used, Year of construction: 2010, machine/vehicle number: 1000017741, inner dimension length: 1,000 mm, inner dimension width: 840 mm, inner dimension height: 815 mm, operating temperature: 1,700 °C, usable tank capacity: 685 l, No minimum price – guaranteed sale to the highest bidder! The machine was professionally dismantled and stored. All parts and connections are labeled for reassembly. An on-site inspection is possible at any time. TECHNICAL DETAILS Furnace chamber and usable space Usable batch space (W × H × L): 840 × 815 × 1,000 mm Total length of the graphite box: approx. 1,100 mm Usable volume: approx. 685 l Operating temperature: max. 1,700 °C Operating temperature under partial pressure: max. 1,500 °C Operating temperature under vacuum: max. 1,700 °C Temperature uniformity: ± 10 K Temperature fluctuation in the steady state: ± 5 K MACHINE DETAILS Process pressure range: 1 × 10⁻² < p < 1,040 mbar Final pressure in the empty, clean, and cold furnace: < 1 × 10⁻² mbar Leak rate: < 5 × 10⁻³ mbar·l/s Power supply: 3 × 400 V, 50 Hz Permissible voltage fluctuation: max. ± 5 % Installed heating power: max. approx. 190 kW Electrical power of the pump station: approx. 14 kW Cooling water flow rate: approx. 150 l/min Cooling water temperature: 20–30 °C Cooling water pressure: 2–4 bar Cooling water quality requirements: according to specification PW 800 943 ND Dedpfx Asz I Tt Isl Aewc Compressed air for valve operation: 4–5 bar Nitrogen inlet pressure: 5–7 bar Hydrogen inlet pressure: 5–7 bar EQUIPMENT Double-walled furnace chamber made of stainless steel with water cooling Internal graphite box for precise guidance of the process gases Post-cleaned graphite components Automatic control of the entire process Pump station Labeled lines and connections for easier recommissioning Note: Two internal graphite heating elements were damaged during dismantling and must be replaced.

Condition: excellent (used), Year of construction: 2026, machine/vehicle number: 62401, functionality: fully functional, total length: 7,050 mm, total width: 2,550 mm, total height: 2,500 mm, overall weight: 3,400 kg, Dry wood chips, firewood and other coarse, wet biomass in a container that goes straight onto your truck, with warm air blown through the perforated floor. This Lauber TroCo drying container was built in 03/2026 and has been used only three times by us. It is in very good condition and ready to dry. Only one unit available. This is a single used machine, not ongoing stock. Once sold, it is gone. Best for: drying coarse, wet biomass such as wood chips, firewood and other coarse plant material, then moving the container to where you need it with a hooklift truck. Not suitable for: finely ground bulk material unless you verify it with us first. A warm air source and the air hose are not included, you need to supply them. What the specifications mean in practice: - 34 m3 volume - one large batch per drying cycle instead of many small ones - Hooklift system (locking dimension 3,890 mm) - load, move and unload with a standard hooklift truck, no crane needed on site - Perforated ventilation floor with round air connection at the door end - warm air is pushed up through the whole load, so it dries evenly - Fitted tarp cover - keeps rain out during storage and transport - Rear rollers and ladder steps on the front - easier to roll off and to inspect the load - Gross weight rating 21,000 kg - heavy loads are no problem for the frame Technical data (from the nameplate): - Manufacturer: Lauber Trocknungstechnik, type TroCo, serial no. 62401 - Year built: 03/2026 - Volume: 34 m3 - Length: 7,050 mm, height: 2,500 mm - Empty weight: 3,400 kg, permissible gross weight: 21,000 kg Djdpfxoz I Dzis Al Ajwc - Locking dimension: 3,890 mm - Colour: yellow - Safety inspection label (DGUV Rule 114-010) from the container builder is fitted, see nameplate photo Condition: Built 03/2026, used only three times by us, very good condition. Fully functional. Location: Stanserstrasse 50, 6064 Kerns (self pick-up, transport by arrangement). A hooklift truck, a suitable forklift or a crane is needed for loading. The container weighs approx. 3,400 kg empty. Why you can buy with confidence: - Built 03/2026, used only three times - Used by us, not rented out - Nameplate photos available, in-person inspection in Kerns OW by appointment Inspect before you buy: you may verify identity, condition and completeness at inspection or pickup. We guarantee what we control: the machine is what this listing says it is. We do not promise performance in an application we cannot assess, which is why we ask about yours first. Why buy now: This is a single used unit. Once sold, it is gone. Inspection is available in Kerns OW by appointment. First-buyer bonus: buy within the next two weeks (until 20 October 2026) and we take CHF 500 off the price. Valid until 20 October 2026, or until the machine is sold. Action: Send us your intended material, batch size and destination. We will confirm suitability and give you a transport estimate.

Condition: like new (used), Edwards Edwards iXH4545H – Industrial High Vacuum / Dry Pump For sale is an Edwards iXH4545H, version MK1 HV MM96 Black EMS. Dwodpszixyfofx Al Aoc This unit originates from a technical company environment and is part of Edwards’ high-performance iXH series, which is used globally in industrial high vacuum and coating processes. Technical Data Manufacturer: Edwards Model: iXH4545H Version: MK1 HV MM96 Black EMS Weight: approx. 890 kg Technical Specifications (iXH Series) Dimensions: approx. 1,240 × 860 × 1,310 mm (L × W × H) Pumping speed: up to approx. 4,500 m³/h (depending on gas & configuration) Ultimate pressure: < 1 × 10⁻² mbar Inlet: ISO 100 / ISO 160 Outlet: KF 40 / NW 40 Power supply: 400–480 V, 3-phase Power consumption: typical 12–18 kW Cooling: water-cooled (approx. 6–10 L/min) Description: The Edwards iXH4545H is an industrial high vacuum/dry pump from the 4500 series. It is typically used in: • PVD / CVD coating • Semiconductor industry • Process chambers / vacuum furnaces • Research & development • High gas load applications • Chemical/corrosive process gas environments The iXH series is renowned for its high reliability, robust construction, and 24/7 operational capability. Weight: approx. 890 kg Condition: used Scope of delivery: (see picture) (Subject to changes and errors in technical data and specifications!) For further questions, we are happy to assist you by phone.

Condition: ready for operation (used), Year of construction: 2019, operating hours: 30,745 h, functionality: fully functional, overall weight: 2,700 kg, power: 388 kW (527.53 HP), type of input current: three-phase, number of chambers: 3, Equipment: documentation/manual, We offer this ready-to-use Lauber L-ENZ 370 drying system, manufactured in 2019. – professional wood dryer, 388 kW + 3 drying containers Technology from the German manufacturer LAUBER Trocknungstechnik, manufactured in 2019, serial number 41199. The equipment is suitable for utilizing excess heat from a boiler, biogas plant, cogeneration unit, biomass boiler, or other heat source. Technical parameters: - Manufacturer: LAUBER Trocknungstechnik - Type: L-ENZ 370-4 - Serial number: 41199 - Year of manufacture: 2019 - Thermal output: approx. 388 kW - Fan: 11 kW - Power supply: 400/230 V, 3~NPE, 50 Hz - Automatic LAUBER control - Touchscreen control panel - Fan frequency inverter - Circulation pump control - Heat exchanger - WILO circulation pump - Complete electrical installation and switchgear - Complete technical documentation The technical documentation states a thermal output of 388 kW, operating temperatures of 90/65 °C for the heating water, and a water flow rate of 15.2 m³/h. The weight of the unit itself is approximately 2,700 kg. Zeichnung_LENZ_370_4_mit_techni… Drying containers The offer includes: 3 × drying container - Volume of one container: 15 m³ - Total capacity: 45 m³ - The containers are designed for drying material using the LAUBER hot-air system. Suitable applications: The technology is particularly suitable for: - 🌲 firewood - 🌲 wood chips - 🌲 wood biomass - 🌲 sawdust - 🌲 other loose wood materials - or other materials depending on the specific drying technology The LAUBER system uses warm air, which is blown through the material being dried in the containers. The manufacturer uses it for drying wood chips, firewood, and other loose materials. lauber-holztrockner.de Dimensions of the main unit Approximately: 4,630 × 2,390 × 2,750 mm Weight approx. 2,700 kg. Condition: Dwodpfsz I Throx Al Ajc The technology is unused and offered for sale. Complete technical documentation is available, including electrical diagrams, technical drawings, and the manufacturer's documentation. Condition: ready to use Type: drying system If you have any questions or require further information, please do not hesitate to send us a message or contact us by phone.

Condition: like new (used), Year of construction: 2024, machine/vehicle number: 8445, functionality: fully functional, operating hours: 3,000 h, power: 80 kW (108.77 HP), input voltage: 380 V, input current: 126 A, input frequency: 50 Hz, type of input current: three-phase, temperature: 750 °C, inner dimension height: 1,000 mm, total height: 4,425 mm, number of chambers: 1, control type: PLC-controlled, actuation type: electric, fuel type: electric, Equipment: CE marking, documentation/manual, We offer this Rohde SG 80/120 nitriding furnace, which is new and manufactured in 2024. Manufacturer: Rohde Schutzgasofen GmbH Model: SG 80/120 Year of manufacture: 2024 Condition: As new Category ID: 34 Type ID: 4293 Dwsdpezuabzofx Al Ajc Type: Nitriding furnace If you have any questions or need further information, please do not hesitate to send us a message or contact us by phone.

Condition: reconditioned (used), functionality: fully functional, Year of construction: 2012, Glastronic-made 1600mm vertical glass washing and drying machine. The machine is in a well-maintained and inspected condition, ready for immediate use. New squeegee rubbers, new bearings. Working direction: left to right. Maximum washable glass height: 1600mm. Number of brushes: 4. Drying fan. Dedpfoz Ngyrex Al Aewc Stainless steel cabin. Water heating. Backlighting. Stop sensor. The machine has been fully inspected, cleaned, and is in perfect working order and can be viewed at our facility!

Condition: new, Year of construction: 2026, functionality: fully functional, power: 11 kW (14.96 HP), A triple pass rotary drum dryer is a type of industrial dryer that is used to reduce or remove moisture from a material. It gets its name from the three rotating drums through which the material passes, each with a different purpose in the drying process. This type of dryer is commonly used in the production of various bulk solids, including minerals, agricultural products, and biomass. Dwsdpfxeq Nfuze Al Aec Here are the key features and components of a triple pass rotary drum dryer: 1. Triple Pass Design: - The material being dried passes through three rotating drums or cylinders, hence the term "triple pass." Each drum serves a specific purpose in the drying process. 2. Material Flow: - The material enters the dryer and first passes through the innermost drum. After the initial drying phase, it moves to the middle drum and then to the outer drum, undergoing additional drying in each pass. 3. Heat Source: - Heat is typically provided by a combustion system, such as a burner or furnace, located at one end of the drum dryer. The hot gases generated by the combustion process flow through the rotating drums, transferring heat to the material. 4. Air Flow: - The dryer is designed to optimize air flow through the drums, ensuring efficient drying. In a triple pass design, the material and hot gases move counter-currently through the three drums, enhancing heat transfer and drying efficiency. 5. Lifting Flights or Lifters: - Lifters are internal components inside the drums designed to lift and cascade the material as it rotates. This movement promotes good heat transfer and uniform drying. 6. Retention Time: - The triple pass configuration allows for an extended retention time of the material in the drying system. This longer exposure to heat enhances the drying efficiency, making the triple pass rotary drum dryer suitable for materials with high moisture content. 7. Cooling Section: - After the material completes the three passes and reaches the end of the drum dryer, a cooling section may be included to reduce the temperature of the dried material before it is discharged. 8. Applications: - Triple pass rotary drum dryers are used in various industries, including agriculture (drying crops like grains), minerals (drying ores or concentrates), and biomass (drying wood chips or other organic materials). 9. Efficiency and Energy Consumption: - Triple pass rotary drum dryers are known for their high efficiency due to the extended drying time and effective heat transfer. However, they may have higher energy consumption compared to single or double pass dryers. When selecting a triple pass rotary drum dryer, it's essential to consider factors such as the type of material to be dried, required moisture reduction, and overall processing requirements. Proper design and operation are crucial to achieving optimal drying performance. Technical details We have different options for different requirements, please contact our team for more info.

Condition: like new (used), Year of construction: 2014, machine/vehicle number: 618, functionality: fully functional, operating hours: 800 h, power: 80 kW (108.77 HP), input voltage: 400 V, input current: 250 A, input frequency: 50 Hz, type of input current: three-phase, temperature: 1,200 °C, inner dimension length: 600 mm, inner dimension width: 400 mm, inner dimension height: 400 mm, total length: 4,900 mm, total width: 2,950 mm, total height: 2,900 mm, overall weight: 10,000 kg, number of chambers: 1, number of shelf rows: 1, control type: PLC-controlled, actuation type: electric, Equipment: CE marking, documentation/manual, Condition: very good; the furnace has only been used for 100 batches. The delivery includes a loading electric cart and three charging baskets. Direct sale to end-users only. Dwodpfx Ajzz A Rrsl Aoc W-Technology s.r.o. Polní 8 79201 Bruntál Czech Republic

Condition: used, Year of construction: 1982, power: 36 kW (48.95 HP), input voltage: 380 V, temperature: 950 °C, control type: manual, actuation type: manual, SIMPLON Industrial Annealing/Hardening Furnace (36 kW, max. 950 °C) Dedpfx Aljz Iv H Re Aewc For sale is a robust industrial annealing furnace from the brand SIMPLON (Albert Baumann Aue/Sa. Industrial Furnace Construction). This furnace is ideal for the thermal treatment, annealing, or hardening of metallic workpieces and is equipped with a solid furnace door that can be manually operated via a lever mechanism. Technical Data & Equipment Details: Manufacturer: SIMPLON / Albert Baumann Aue/Sa. Industrial Furnace Construction Year of Manufacture: 1982 (according to the nameplate "82") Order Number: 12362 Maximum Temperature: 950 °C Connected Load: 36 kW Voltage: 380/220 Volts Control: Integrated analog control panel with a stepped switch and analog temperature display (scale x100 °C). Condition: Used industrial quality with visible signs of wear and superficial rust on the housing, consistent with its age.

Condition: good (used), Year of construction: 1983, functionality: unexamined, machine/vehicle number: SFV 1139, overall weight: 1,000 kg, total height: 1,800 mm, total width: 500 mm, total length: 4,150 mm, power: 3.4 kW (4.62 HP), This is a vibrating conveying / vibrating fluidized bed dryer-cooler unit from SCHENCK Process (SFV series/type). Operation: The equipment uses vibration to advance the bulk product along a perforated grid (width 260 mm). Air (hot or cold) is generally injected from below to fluidize, dry, cool, or dust-remove the material during its transfer. Drive system: It is powered by two Schenck vibrating/unbalance motors (SED 180-4 type), each with a power of 1.7 kW, mounted under the chassis. They create the oscillatory movement necessary for transport via micro-jumps. Suspension: The machine body rests on large coil springs to isolate the fixed white chassis (3210x730x930 mm) from the vibrations. Dwedpfozxzrpex Al Aoc Materials: Constructed of stainless steel with sealed inspection ports, suitable for the requirements of the food, chemical, or pharmaceutical industries.

Condition: good (used), Year of construction: 1973, rust size: 700 x 650 x 1.100 mm batch weight: 1.000 kg Dwodpozvfdqjfx Al Asc Temperature: Max. 750 °C connected load: 78 kW Equipment: Incl. Control system (should be renewed) + Charging machine others: Furnace can be moved under nitrogen

Condition: new, Here we offer a ULVAC dry vacuum pump. ULVAC dry vacuum pump Solution for demanding process applications Dry vacuum pump ULVAC's unique approach to utilizing the latent heat within the Dwjdpfjzdqtgjx Al Asc pump body enables the LR/HR/UR series to deliver performance even in the most demanding processes. ULVAC has focused its design efforts on maintaining an extremely uniform, high temperature across all pump stages, optimizing this pump family for CVD and etching applications. Compatible with the ULVAC ECO-SHOCK system for additional energy savings. Features: The LR series pump is designed for load lock chambers and PVD processes. ULVAC's unique aluminum design enables very uniform temperature distribution throughout the pump body: The ULVAC LR series pump is designed for applications that require a heated pump, heated gas lines, and/or heated exhaust lines. Excellent helium pumping capacity Sealed motor for safety and ease of maintenance Withstands power interruptions of up to 500 ms. Internal components are specially treated to ensure a high degree of surface hardness and excellent corrosion resistance. This prevents the wear of internal pump parts when exposed to corrosive gases. (LR series) Designed for process gases that generate powdery byproducts, such as Si crystal growth furnaces. Pre-pump for turbo-molecular and mechanical booster pumps Type: LR600 Condition: new Scope of supply: (See image) (Subject to changes and errors in technical data and specifications!) We would be happy to answer any further questions you may have by telephone.