Used Double Belt Press for sale (30,735)

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, table length: 600 mm, table width: 600 mm, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Dodpek S Dt Tsfx Albjcl Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: used, Year of construction: 2016, Overview This belt press was manufactured in 2016 by SRAML. The machine is designed for the continuous extraction of juice from crushed apples using a continuous belt pressing system. The SRAML TP50 belt press is delivered together with the SRAML JF1500 mechanized self-cleaning filter, which removes impurities such as seeds and stems. It was operational when taken out of regular production and has been maintained as backup equipment. The machine was replaced by a higher‑capacity press. Technical data  Dsdpfjzpffhjx Albocl - Capacity: 700 kg/h (apples) - Application: Juice extraction from crushed apples - Configuration: Continuous belt pressing system with mechanized self‑cleaning filtration system - Filtration system: Mechanized self‑cleaning filter for removal of seeds and stems Scope of Delivery - Belt Press | SRAML | TP50 | 700 kg/h | 2016 - Self-Cleaning Filter | SRAML | JF1500 | Removal of seeds and stems | 2016 - Spare parts | Belts, rollers, bearings, self-cleaning filters with pump, gearbox, 0.75 kW motor and further wear parts

Condition: used, Year of construction: 2008, pressing force: 300 t, table width: 1,000 mm, table length: 2,000 mm, total length: 4,000 mm, total width: 3,000 mm, total height: 4,000 mm, stroke adjustment: 200 mm, Equipment: safety light barrier, We offer this used AIDA 300 Ton ULX eccentric press double column, year of construction 2008. Manufacturer: AIDA Model: 300 Ton ULX Pressing force: 300 ton Year of construction: 2008 Condition: used Category ID: 1329 Type ID: 871 Machine type: eccentric press double column From the first owner company Machine is in great condition and in operation Used always under its capacity Used only in 1 shift from the purchase time untill now Made in Aida Japan First ULX press in Europe Delivery Terms: EXW ESKISEHIR TURKEY Payment Terms: Cash Or Letter Of Credit Djdpfx Aleytcwwjbscl If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: used, Double-column hydraulic press, NEFF type RHS 125 Z Hydraulic drawing press Machine no. 3973, year of manufacture 1983 Pressing force 125 tons Column width 1050 mm Column opening, side 550 mm Table area 1000 x 800 mm Ram area 1000 x 800 mm Ram stroke 350 mm Installation height max. 750 mm Table height above floor 960 mm Drawing cushion force approx. 12 tons at 105 bar Drawing cushion stroke 100 mm Through-hole in the table Ø 202 mm Rapid traverse speed, downward approx. 360 mm/sec Rapid traverse speed, upward approx. 360 mm/sec Working speed approx. 36 mm/sec Oil tank capacity approx. 1000 liters Motor power, main pump 22 kW Motor power, control pump 4 kW Motor power, control pump 2.2 kW Power connection 400 volts, 50 Hz - Hydraulic drawing cushion under the table with a hole through the table plate Ø 202 mm - Precise 4-way column guidance on the ram corners - Stepless pressing force adjustment - Adjustable fixed stop, electrically controlled via a hydraulic motor - Stroke damping - 2-hand control panel for releasing the lifting motion on the press Dcodpfx Alsguvtlebjl - Control cabinet positioned next to the press (1600 x 500 mm) - Documentation including operating manual, electrical wiring diagram, and PLC program printout available Space required for the press L x W x H 2600 x 2400 x 4270 mm Weight approx. 14 tons Good condition

Condition: used, Year of construction: 1998, machine/vehicle number: 098211, KP09 Üretim Markası: OMERA H TİPİ EKZANTRİK PRES Makinenin Üretim Yılı: 1998 Kapasite : 500 TON Hava Tüketimi (m3/saat) : 30 Güç (KW) : 70 Dodpjzxq Uyjfx Albocl Kapladığı Alan (m2) : 44,12 Lokasyon: KOCAELİ/ÇAYIROVA Üst Tabla Ebatları : 268 cm x 135 cm Alt Tabla Ebatları : 270 cm x 135 cm Pres Yükseklik : 5,25 m Pres En : 4,10 m Pres Genişlik: 2,05 m Dakikadaki Vuruş Sayısı : 55 spm Sac sürücü, Sac açıcı ve Sac doğrultucu Markası : Dimeco

Condition: excellent (used), Year of construction: 2016, Specifications Manufacturer: IMV Model: DM125 Year: 2016 Condition: Used Stock number: 0396 Ram force: 1,250 t Number of press points: 2 Drive: Eccentric with stroke adjustment Dsdpfoyw Uf Ajx Albscl Ram stroke: 250–400 mm Strokes/min: 5–35 Vertical daylight below bolster, CBRA: 1,150 mm Table dimensions: 4,500 x 2,000 mm Ram dimensions: 4,500 x 2,000 mm Side column window: 2,600 mm Max. front column window: 4,900 mm Transfer cart: 2 units present Main motor power: 290 kW Press weight: 310,000 kg

Condition: used, pressure 200 t distance between columns 1600 mm max. ram stroke 600 mm dayligth 900 mm table width 1600 mm table depth 1300 mm table height 1060 mm ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 rapid traverse 400 mm/s return speed 325 mm/s Djdpfxsg S R Twj Albjcl pressing speed 42 mm/s bei 40% mm/sec pressing speed 20 mm/s bei 100% mm/sec die-cushion pressure 800 kN die cushion stroke 150 mm speed of die cushion auf 68/ ab 225 mm/s

Condition: used, Machine not operational - control system not functioning Available at a special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Factory No. 300487, Year of Manufacture 2006 Pressing force: 500 tons Distance between columns (front and rear): 2520 mm Table area: 2500 x 2500 mm Ram area: 2500 x 2500 mm Ram stroke: 600 mm Maximum installation height: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Adjustable forward speed: 100-800 mm/s Pressure build-up to 5000 kN: approx. 0.7 sec. Return stroke speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-fold flat guide for the ram - Hydraulic ram locking in the top dead center position - Adjacent control cabinet (200 x 50 cm) - Electrical control system SIEMENS PLC S7-314 - Operation via SIEMENS OP 170-B (5.7") Dsdpfx Aljdzqptobecl - 2-hand control panel located beside the machine - Floor-level installation - Table top 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication system - Operating manual with circuit diagrams Space requirement (L x W x H): 372 x 260 x 460 cm Space requirement for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Year of construction: 1990, condition: good (used), machine/vehicle number: XXXX, Item No. 17415 Technical data: - Sanding belt dimensions approx. 50 x 2500 mm Djdpfx Ask D Dxfelbjcl - Contact wheel diameter approx. 250 mm - Drive 400 V / 5.5 kW - Space requirement approx. W 1350 x H 2050 x D 900 mm - Weight approx. 200 kg

Condition: excellent (used), Year of construction: 1989, functionality: fully functional, power: 3 kW (4.08 HP), input voltage: 380 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 16 t, stroke length: 100 mm, table width: 440 mm, table length: 320 mm, clearance between the columns: 500 mm, oil tank capacity: 60 l, total length: 1,040 mm, total width: 1,030 mm, total height: 2,000 mm, 16 ton hydraulic press for sale in good condition HANS SCHOEN TES 16 two-column hydraulic press Year of manufacture: 1986 Pressing force 160 kN motor power: 3kw 380v 50Hz two-hand operation Installation height: 280 mm Stroke: 100 mm Dedpfx Alszf Ilcsbecl Table width: 440 mm Table depth: 320 mm Machine dimensions: height: 200cm width: 103cm length: 104cm weight: 1000kg.

Condition: ready for operation (used), Two mechanical large-format double-column eccentric punching presses Rhodes (UK) are available. Press force: 350t, table dimensions X/Y: 1750mm/920mm, ram dimensions X/Y: 1550mm/615mm, ram stroke: 101mm, ram adjustment: 100mm, stroke rate: 50 strokes/min, max. installation height: 483mm, side opening X/Y: 630mm/380mm, table height: 933mm, weight: approx. 43000kg. Documentation available. On-site inspection is possible. Dodpfoyfv I Tex Albocl

Condition: used, It was used for extracting juice from apples. Belt width: 200 cm, capacity approximately 16 tons/hour, juice yield 60–78% depending on the quality of the raw material. Dcjdpfsxn Uluox Albjl

Condition: used, Year of construction: 1992, machine/vehicle number: 77K2, KSP11 SACMA double-pressure press, without thread roller, used, very good condition Dcjdpfx Ajwiwqfolbsl

Condition: used, Double-column Hydraulic Press SCHÖN Type SH 25 Machine No. 2440 Year of manufacture: 1979 Press force: 25 tons Column spacing: 630 mm Lateral passage between columns: 120 mm Table area: 580 x 320 mm Ram area: 360 x 220 mm Clamping pin hole: Ø 40 mm Maximum ram stroke: 100 mm Maximum installation height: 270 mm Table height above floor: 900 mm Djdpfjyz Dr Tox Albocl Motor power: 7.5 kW Power supply: 380 Volt, 50 Hz - Main cylinder overhauled in 2025 - SICK LUV 206 safety light curtain - Two-hand control - Stroke counter - Rapid stroke and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Press force regulation - Press time extension 1–10 s (pressure holding time) - No operating manual and no wiring diagrams Required space (L x W x H): 1450 x 1100 x 2200 mm Weight: 1200 kg In good condition

Condition: used, Eccentric stamping press HAULICK + ROOS, Type RVD 125 Double-column eccentric press Machine No. 212560, Year of manufacture 1981 Pressing force 125 tons Table size 880 x 800 mm Table opening 470 x 140 mm Column distance 900 mm Column distance, side 415 mm Dcodpfxehlnzke Albsl Ram stroke 45 mm Ram adjustment range 0-80 mm Installed height as shown in the picture 340 mm Stroke rate 50 to 300 strokes/min Motor power, main drive 22 kW Power connection 380 volts, 50 Hz - Double connecting rod drive with 4-bearing eccentric shaft for off-center ram pressure load - Adjacent electrical cabinet - NC roller feed EBU, width 250 mm, year of manufacture 2003 - Adjacent control panel for the roller feed - Strip feed direction from left to right Space requirement (press) L x W x H 3000 x 2000 x 3020 mm Transport height 2950 mm Weight of the press approx. 11 tons

Condition: new, Specifications: capacity up to 600 kg/h power: drive motor 0,75 (1,02) kW (PS) brush cleaning 0,37 (0,5) kW (PS) high pressure cleaner 4,7 (6,4) kW (PS) electric outlet 400V 50Hz (3 phases) fuse 16 A dimensions: length 1 825 mm width 1 085 mm Dcedpfx Asd Nrakslbel height 1 290 mm insertion resp. discharge height 1 290 mm belt width 420 mm spread width 300 mm spread height 10 - 50 mm weight (belt press) 550 kg material 1.4301 / AISI 304 juice yield up to 75 % belt speed (continuously) 2,1 - 5,5 m/min lead time 0,4 - 1 min water connection min. G ½ “, min. 12 l/min juice discharge height 305 mm pomace discharge height 780 mm suitable for pomaceous and stone fruit scope of delivery high-pressure cleaner, compressor

Condition: used, pressure 1000 t distance between columns . mm stroke . mm total power requirement . kW The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are Djdpfx Aozk Rcuolbecl possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Technical details: pressure: 80 t dayligth: 600 mm ram stroke: 200 mm pressure: 30 t dayligth: 680 mm ram stroke: 300 mm distance between columns: 1060 mm base plate surface area: 1060x600 mm table above floor: 720 mm ram stroke speed: Stößel/ Ram 1: 40 mm/sec ram stroke speed: Stößel/ Ram 2: 95 mm/sec base plate surface area: Dm=150 mm total power requirement: 13 kW weight of the machine ca.: 4,5 t space requirement approx.:: L:1,6xB:1,1xH:3,4 m - Press with two ram with 30 t + 80 t - foot control Dcedpfxsu Nfnwe Albsl - documentation *

Condition: used, Technical details: pressure: 80 t distance between columns: 880 mm dayligth: 200 mm Table dimensions: 880x300 mm height over floor: 1000 mm distance between columns: 800 mm total power requirement: ca. 12 kW machine weight ab.: 2855 kg Dcjdpfxsu Icwte Albjl space requirements of the machine approx.: T:1,4xB:1,65xH:1,9 m Embossing - Hot Embossing application area: - for example: for foils, plastics, paper, hardboard materials etc. - stamp plate size: 600x310mm equipment: - counter - hydr. tank Accessories: - Mounting plate (600x300x90mm) not heatable. Sale as is. *

Condition: new, pressure 400 t distance between columns 600 mm stroke 600 mm table-size 3000 x 1500 mm travel x / y 2200 x 900 mm working feed 7 mm/sec tank capacity 66 l working pressure 30-250 bar total power requirement 18,5 kW weight of the machine ca. 25 t dimensions of the machine ca. 3500 x 3500 x 3700 m 2. STANDARD EQUIPMENT FRAME - Welded steel frame - Frame and plates are precision-milled using a CNC milling machine - Chrome-plated cylinder Dcodpozyvakjfx Albjl - Worktop with threaded holes HYDRAULICS - Bosch Rexroth hydraulic pump - Hydrapack or Badestons hydraulic directional control valve - Hydraulic block in accordance with EN standards - 1000-liter hydraulic oil tank - Pressure adjustment via pressure transmitter/regulator ELECTRICS - Control cabinet in accordance with EN standards - All cables are labeled and clearly arranged - All electrical components are from Siemens CONTROL PANEL - Stroke control in any position - X, Y, and Z-axis movement via remote control - Stroke adjustment via sensor SAFETY - The machine complies with the EC safety standards 2006/42/EC Machinery Directive, EN ISO 16092-01 and 16092-03 - Two-hand operation - Emergency stop button - Safety rope with switch around the press 4. TRANSPORT AND INSTALLATION – The price includes transport costs, installation, and training at the customer's factory. – Hydraulic oil is not included in the price. – All handling costs (e.g., crane, forklift, etc.) are borne by the buyer. 5. WARRANTY – The machine has a 2-year manufacturer's warranty. – This warranty covers the delivery of all spare parts required for repair and service of the machine. Damaged parts will be returned to the manufacturer after replacement with a new part. – This warranty does not cover parts damaged due to improper use.

Condition: used, Technical details: pressure: 20 t slide stroke: 6 - 60 mm throat: 176 mm ram adjustment: 55 mm no. of strokes: 155 Hub/min distance table/ram: 270 mm passage width: 470 mm Table dimensions: 300 x 450 mm passage opening in table: 90 mm surface area of ram: 130 x 248 mm inclination: 28 ° mortise hole in ram: 25 x 65 mm Dcjdpfx Alou Nfliebel table height over floor: 775 mm air pressure - required: 5,5 - 6 bar total power requirement: 3,5 kW weight of the machine ca.: 1,0 t dimension machine approx.LxWxH: 1,3 x 1,1 x 1,95 m High performance press Central lubrication with light barrier (monitored) Linuflex stroke counter (counter) additional steel plate 315 x 400 x 50mm with center hole Ø 63mm *

Condition: used, Year of construction: 1998, machine/vehicle number: 2 / 2000, Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Dodpoyvz Stofx Albecl Die cushion capacity in table: 400 ton Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Height over floor approx.: 11350 mm Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton Standard configuration Moving bolster front sidePin diameter 52 mmForce in microinches = 400 tA SIEMENS control system is installed The documentation is available.A packing list would be available, as an identical press has already been dismantled.

Year of construction: 2026, condition: new, The obtained juice flows into integrated collection tank under the press. Then the pump transfers the juice from the press to a desired tank for further processing. The pressing process is continuous. Capacity: 3000 kg/h. The most evolutionary feature of our Belt press POWERPRESS line is that belt presses come with integrated pump and juice collection tank. This means you save money and do not need additional juice collection tank and pump which otherwise would use much space and cause additional costs. -The juice yield of apples using our belt press 3000 is ~75 %. -There is a filtration sieve integrated into the juice collection tank. It filtrates the juice providing clearer and purer product. -The belt presses work automatically: when the mash inlet tank is full, all other machines, which come before belt press, turn off automatically. When the juice tank is full, the pump automatically pumps the juice into the tanks. -The belt press 3000 includes a high-pressure washer, which continuously washes the belt of the machine. Our belt washing system is simple, does not contain any engines or reducers, so it prolongs the use time and saves the service costs. -Pneumatic lifting of the security cover of the press ensures easier access when cleaning. Dcjdpeq Nl Aqsfx Albsl -After work, belt press should be manually washed with a water stream. A full washing process takes around 15-20 minutes. Washing is simple and all the parts of the belt press are easily removable without any tools. -Belt tension is adjustable. -Machine is made entirely of stainless steel and has adjustable feet for more convenient use. -Easy to clean with no closed or inaccessible spaces, all parts are easy to assemble.

Condition: used, Year of construction: 1998, machine/vehicle number: 1 / 2000, Pressure total: 2000 ton Ram stroke: 900 mm Slide adjustment: 800 mm Shut height (stroke down, adjustment up): 1800 mm Free frontal opening L-R: 5040 mm Distance between oil tray: 4840 mm Distance between the columns F - B: 2600 x 2400 mm Table surface area : 5000 x 2700 mm Slide area: 5000 x 2700 mm Die cushion capacity in table: 400 ton Die cushion stroke: 350 mm Die cushion pad area: 4200 x 2100 mm Cushion pressure in ram: 200 ton Ejector stroke in ram: 200 mm Number of strokes: 8 - 14 s.p.m. Required power: 350 kW Height over floor approx.: 11350 mm Dodpjyvz U Ijfx Albjcl Die weight at the ram max.: 40000 kg Die Weight total: 80000 kg Weight of machine approx.: 580 ton Standard configuration Moving bolster front sidePin diameter 52 mmForce in microinches = 400 tA SIEMENS control system is installed The documentation is available.A packing list would be available, as an identical press has already been dismantled.

Year of construction: 2026, condition: new, functionality: fully functional, Belt press POWERPRESS 300 is designed for pressing fruit, berry and vegetable mash. Fruit mash is supplied on the belt which presses it against shafts. The obtained juice flows into a small collection tank under the press with filtration sieve on top. Then the external pump or juice collection tank with pump transfers the juice from the press to a desired storage tank or straight to ROCKET pasteurizer for further processing. The pressing process is continuous. Capacity: 300 kg/h The most cost-efficient belt press in the market! The most evolutionary feature of our Belt press POWERPRESS 300 is one huge pressing shaft, which lets the machine to maintain the longer pressing time (belt length is 4900 mm) and huge shaft dimensions squeezes the juice efficiently by saving the costs and space. The juice yield of apples using our belt press is ~65-75 %. The yield highly depends on freshness and variety of fruits. Dcodpfxjt Rft Uo Albol There is a filtration sieve integrated into the juice collection tank. Because of that the belt press 300 filtrates the juice even during the pressing stage providing cleaner and purer product. The belt press includes a high-pressure washer, which continuously washes the belt of the machine. Our belt washing system is simple, does not contain any engines or reducers, so it prolongs the use time and saves service costs. Adjustable fruit inlet lever lets fruit mash supply onto the shaft easily. Crushed fruit mash can be supplied from MAXIMILL or straight from a bucket or basket. After work, belt press should be manually washed with a water stream. A full washing process takes around 15 minutes. Washing is simple and all the parts of the belt press are easily removable without any tools. Belt tension is adjustable. The machine is made entirely of stainless steel and has adjustable feet. Easy to clean with no closed or inaccessible spaces, all parts are easy to assemble.