Used Cold Rolling Machine for sale (69,498)

Condition: used, Year of construction: 2016, Technical details: Pjdszrfm Dspfx Ahcsra weight: 22 t

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Predpfx Ahsuz If Necoa Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, Thread rolling machine UPWS 25. Predpfx Ahjzd Rf Necoa

Condition: used, Year of construction: 1987, rolling capacity max. NA t workpiece diameter 38 mm workpiece length 500 mm total power requirement 24 kW weight of the machine ca. 10 t dimensions of the machine ca. m Max.Ø tool slide stroke 760 mm Max.Ø rack length 610 mm Length of workpiece between centres, approx. 500 mm Max. tooth width / profile width 92 mm Max. workpiece Ø 38 mm Tailstock stroke on outboard support, hydraulic, approx. 500 mm Module range 0.3 - 1.3 Total electrical load, approx. 24 kW - 380 V - 50 Hz Weight, approx. 10,000 kg Prodpot Hw D Dsfx Ahcsa Accessories / Special Features * KBH Workpiece Feed Device, standing parallel to the machine, at present set-up for feed-in and feed-out of shaft-formed workpieces, approx. Ø 16 x 200 mm long, with prism conveyor belt and lifting station for 2 shafts (blank and finished part), as well as workpiece positioning control. * Originally, external gears were formed on the machine using pinion cages (no. of teeth = 25), Ø approx. 32 mm x 14 mm long, workpiece Ø approx. 80 x 80 mm long. * Various accessories: * Separate switch cabinet. * Separate hydraulic unit, 900 l. * Coolant device in the machine. * Control panel with malfunction message in plaintext, etc. Roto Flo machines are ideal for mass production of smaller gears/profiles. The coldforming process is a lot faster and more economical than other chip removing methods. Workpieces are clamped between 2 live centres and 2 synchronous opposed directional coldforming racks simultaneously engage the workpart and start rotation. During rotation, the profile is formed successively within one stroke. In the calibrating zone, the profiling and surfacing performance of the tool are optimised. Profiles do not require a run-out. The coldforming process requires a rigid and heavy duty construction of the machine, which ensures the required precision over the years. Between 25,000 and 100,000 working cycles can be performed with one set of racks, also for serrations. Condition : Very good. Machine can be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract. Thank you for your interest. We always have a good selection of gear machines available. Please let us know what you need.

Condition: used, Thread rolling machine, cold rolling machine, thread forming machine, profile rolling machine Manufacturer PEE-WEE, Type P 24 Q Serial No. LC2403099, Year of manufacture 2004 Rolling force, max. 24 tons Tool diameter, max. 200 mm Rolling spindle diameter 69.85 mm Tool bore diameter 70 mm (nominal diameter) Receiving length, tool length, max. 180 mm Workpiece diameter, max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 RPM Hydraulic motor power approx. 3 kW Pedpfxeh A S Hte Ahcsra Rolling drive motor power 5.5 kW Mains connection 400 Volt, 50 Hz - Swiveling rolling spindle for thread through-rolling - Rolling spindle speed in 4 stages via gear change - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons Good condition Plunge rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating the workpiece up to the nominal diameter. The thread length is a maximum as long as the rolling tools are wide. Through-rolling tools: If the thread length is greater than the rolling tool width. Through-rolling tools have 3 sections - the inlet, the calibrating section, and the outlet. Grooved rollers have no pitch and are swiveled with the helix angle of the profile to be rolled. Helix rollers differ from grooved rollers by having a pitch in the profile. The sum of the helix angle and the swivel angle results in the helix angle in the workpiece.

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, paper width (max.): 1,800 mm, Unwind diameter: 1,000 mm Rewind diameter: 800 mm Max. speed: 400 m/min Friction shafts for 3 and 6 inch Hydraulic lift at the unwind station Splicing table Web edge control Tidland knife holders, 20 pieces Semi-automatic knife setting system from Tidland Recipe management Predeywl D Njpfx Ahcsa Laser positioning We will also dismantle and load the machine onto a truck or sea container at our own expense.

Condition: used, Year of construction: 2011, Control Siemens Sinumerik 840D sl centre height 1.150 mm z-axis 1.559 / 307 mm x-axis 16 - 80 mm Swing circle diameter 92 mm roll spindle turning speed range 0 - 3.000 U/min Rolling mill roll clearance - axial 0,025 mm feed speeds infinitely variable 0 - 30.000 mm/min rapid traverse 30.000 mm/min Swivel angle range ±3,2 ° Predpezdk Iksfx Ahcea Max. speed - main spindle 375 U/min piston stroke 400 mm diameter of piston 90 mm with effective piston area 63,6 cm² In our assessment, the machine is in good used condition and can be inspected under power by appointment. Accessories, as well as the tools and clamping devices shown in the images, are included in the scope of delivery only if explicitly noted in the additional information. Subject to changes, errors in technical data and specifications, and prior sale!

Condition: refurbished (used), ROLLFORMING MACHINE Pedpfx Asfgl Aqshcjra PRODUCING SQUARE PROFILES WITH 5 TONES OF TOOLS MADE IN ITALY

Condition: used, Year of construction: 2007, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, year of last overhaul: 2022, We are offering this used KÖNIG ECO TWIN roll production line, manufactured in 2007. Model: ECO TWIN Type: 800-(DB800)-K6-SCHN6/B-(DA) Serial number: 07.0.0782 Year of manufacture: 2007 Power: 8 kW Frequency: 50 Hz Rated voltage: 3 × 400 + N V Rated current: 15 A The system has been fitted with new belts and is in perfect, fully functional condition. Pedpfx Ahjznm S Hjcera It was used by us solely as a backup system and was therefore only used very rarely. We acquired and overhauled the system approximately two years ago. The system is immediately available and can be collected directly after arrangement. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: new, Year of construction: 2026, total width: 750 mm, total length: 2,900 mm, total height: 1,160 mm, warranty duration: 12 months, overall weight: 400 kg, Compact roll forming equipment for producing metal rainwater downpipes This portable roll forming machine is designed for the production of rectangular metal downspouts and rainwater downpipes from pre-painted or coated sheet steel. Prjdpfx Ahszrnxcjcsa The machine progressively forms a flat metal strip into a finished rectangular profile suitable for residential, commercial and industrial rainwater drainage systems. The dimensions and geometry of the finished downpipe can be manufactured according to the customer’s technical requirements. The roll tooling is designed for a specific rectangular profile, taking into account the required width, height, corner shape, surface pattern, material thickness and connection type. The machine is suitable for manufacturers of: rectangular metal downspouts; rainwater downpipes; roof drainage systems; gutter and downspout components; roofing accessories; façade and sheet-metal products; custom cold-formed metal profiles. Its compact size and relatively low weight make it suitable for small workshops, roofing companies and production sites where a large stationary roll forming line is not required. Custom profile dimensions The finished profile is produced according to the customer’s drawing, sample or technical specification. The machine is therefore supplied as a custom rectangular downspout roll former, configured for the required finished product. The basic production process is: Decoiler → Roll forming system → Manual saw cutting Main advantages Compact and portable construction Custom tooling for the required downpipe size Production directly from coated sheet steel Suitable for pre-painted and galvanized material Gradual roll forming with controlled material deformation Low installed motor power Simple operation and maintenance Suitable for small-batch and regular production Finished products can be cut to the required length Reduced dependence on purchased ready-made downpipes Suitable for workshops with limited production space Material The standard configuration is designed for coated sheet steel with a thickness of approximately 0.4–0.5 mm. Depending on the agreed configuration, the machine may process: pre-painted steel; galvanized steel; polymer-coated sheet steel; other thin sheet-metal materials after technical approval. The exact material grade, tensile strength, thickness and coating must be specified before the roll tooling is designed. Technical specifications: Machine type Portable roll forming machine Finished product Rectangular metal downspout / downpipe Profile dimensions According to customer specification Material Coated sheet steel Material thickness Approx. 0.4–0.5 mm Forming speed Approx. 3–8 m/min Main motor power 3 kW Transmission Gear and sprocket drive Auxiliary forming elements Polyurethane wheels Cutting system Manual circular saw Machine dimensions Approx. 2860 × 730 × 1160 mm Machine weight Approx. 400 kg Electrical supply 380 V, 50 Hz, 3-phase* Compact machine design This makes it suitable for: roofing contractors; rainwater system manufacturers; sheet-metal workshops; gutter and downpipe producers; building component manufacturers; small and medium-sized production facilities; companies producing custom roofing accessories. Scope of supply A custom set of roll forming tools will then be designed for the required product.

Condition: used, functionality: fully functional, Year of construction: 1971, For sale: this four-roll plate rolling machine, type VRM HY 3000/18. The machine is connected and can be tested. Weight: 24,000 kg. Psdpfxjxwqdrs Ahcera

Condition: new, Year of construction: 2026, Automatic Roll Forming Line for Light Gauge Steel Frame Production This automatic roll forming line is designed for manufacturing Light Gauge Steel (LGS) and Cold Formed Steel (CFS) structural profiles used for steel frame houses, modular buildings, commercial buildings and prefabricated construction systems. The production line automatically performs feeding, leveling, punching, roll forming, profile marking and hydraulic cutting according to digital production data. It is an ideal solution for manufacturers of: Light Gauge Steel structures Steel frame houses Prefabricated buildings Modular buildings Tiny houses Commercial steel structures Residential steel framing Cold formed steel construction systems Flexible Machine Configuration The roll forming line can be supplied in two different configurations depending on production requirements. Fixed Profile Machine Designed for manufacturers producing one profile size with maximum productivity and simplified machine setup. Multi-Profile Roll Forming Machine An adjustable roll forming system capable of producing several profile widths on one machine by changing the roll forming configuration. Prodpjzrt Ivefx Ahcoa This solution provides greater production flexibility while reducing investment costs compared with purchasing multiple dedicated production lines. Complete Automatic Production Process The machine automatically performs the following operations: Coil feeding Strip leveling Servo punching Hole punching Slot punching Service hole punching Roll forming Profile identification marking Hydraulic cutting to length Finished profile discharge The production line is designed to work with professional steel frame design software. The operator imports production data generated from a building design into the machine control system. Based on this information the machine automatically manufactures every structural member including: wall studs tracks floor joists roof trusses rafters beams structural reinforcements Each component is produced with the correct length, punching pattern and identification marking required for final assembly. Automatic Profile Marking Each profile can be automatically marked during production. Typical marking information includes: Profile number Wall identification Member position Assembly reference Project identification Automatic marking significantly simplifies profile sorting and speeds up on-site assembly. Instead of manually identifying every component, installers receive a complete production kit with every profile clearly identified. Automatic Punching System All punching operations are synchronized with the roll forming process to achieve high accuracy and repeatability. Main Advantages Fully automatic production Computer controlled manufacturing Automatic profile marking Servo punching system Hydraulic cutting High dimensional accuracy Reduced material waste Fast production Flexible profile sizes Suitable for custom house projects Reduced manual labour Easy assembly thanks to profile identification Applications Technical Specifications Typical options include: Single-profile roll forming machine Multi-profile adjustable machine Automatic profile marking Servo punching Hydraulic cutting Automatic decoiler Hydraulic decoiler Computer control system Production management software compatibility

Condition: used, functionality: fully functional, Year of construction: 1992, machine/vehicle number: 10842, We are offering this pre-owned sheet metal rolling machine Chr. Häusler VRM-hy 3000x15, year of manufacture 1992. Model: VRM-hy 3000×15 Serial number: WO 10842 Psdpfx Ajx Sqc Tshcera Year of manufacture: 1992 If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: used, Year of construction: 1973, functionality: fully functional, machine/vehicle number: M14L/9094, Offer Number: M14L/9094 Machinetype: thread rolling machine - flat die Make: MENN Type: GW32 Constr. year: 1973 diameter range: 1,6-4 mm shaft length under head: 50 mm Psdpozwqh Refx Ahcera max. thread length: 30 mm output pieces/min: 300-750 Location: In our warehouse

Condition: used, functionality: fully functional, Year of construction: 1997, machine/vehicle number: 9730010, control type: manual, degree of automation: manual, actuation type: hydraulic, number of rollers: 3, roller (top) diameter: 340 mm, side roll diameter: 300 mm, sheet thickness (max.): 20 mm, sheet thickness steel (max.): 25 mm, sheet thickness stainless steel (max.): 20 mm, sheet thickness aluminum (max.): 25 mm, sheet thickness brass (max.): 25 mm, sheet thickness copper (max.): 25 mm, overall weight: 9,000 kg, total length: 5,500 mm, total width: 1,600 mm, total height: 1,500 mm, input voltage: 380 V, input frequency: 50 Hz, number of digital displays: 2, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, 3-roll hydraulic plate bending machine with pre-pinch Model MCO3034 Davi capacity 3000x20 mm -Plate width 3000 mm -Capacity rolling 20 mm -Prebend 16 mm ----- TECHNICAL DATA Top roll 340 mm Surface on the rolls 3050 mm MINIMUM ROLLING DIAMETER ID 430 MM depending on plate thickness and plate yield strength CONFIGURATION: -Rolls hardened high strength surface -Conical plate bending attachment hydraulic -Digital position readouts 2xplate support left and right side hydraulic ( see photo ) -3 rolls driven hydraulic powered with individual motor & gear box on each roll. -Parallelism between top and bottom rollers by torsion bar. Predszwuu Uspfx Ahcoa -Rolls installed on bearings -Overload safety hydraulic protection of the rolls -Synchronized speed hydraulic rotation of the rolls. -Hydraulic unit self enclosed into the machine. -Speed infinitely variable control with leverage hydraulic distributor -Centralized operator control panel hinged on the front floating left right -Emergency shutdown and safety stop system -Manuals original

Condition: excellent (used), Year of construction: 2014, Roller coater BÜRKLE easy coater RCL 12M and UV system easy cure UV - TRUV with 2 lamps and 2 x roller conveyor BÜRKLE easy coater RCL 1300: For one-sided application on flat surfaces from above Operating side left Touch screen control TP 177 Micro Rubberized application roller Hard chrome-plated metering roller can be sensitively adjusted via worm gearbox Controlled belt transport with exposed counter roller for safe workpiece transport Quick-change system with split bearing and cross-disc coupling for easy changing of the application roller Oscillating squeegee, can be changed quickly for cleaning Separate, infinitely variable FU direct drives for application roller, metering roller and transport Reversible dosing roller Motors and limit switches in Ex version on the machine Non-Ex control cabinet and control panel outside the danger zone on the machine Mobile version Electrical preparation for integrating the roller coating machine into a coating line Technical data Working width: 1300 mm Workpiece height 3 - 80 mm Prjdpfx Aot Dx U Sjhcoa Min. workpiece length 400 mm Rubberized application roller DM 240 mm Chrome-plated metering roller DM 172 mm Transport speed 2 - 15 m/min variable Connected load approx. 2.4 kW Speed of metering roller 1.0 - 3.0 m/min Working height 900 mm (+/- 20) Safety equipment according to CE Incl. switch cabinet Weight approx. 1650 kg UV system e.a.s.y. cure UV - TRUV with 2 lamps One-sided curing of UV-curing lacquers on flat workpieces from above Incl. control cabinet Working width max 1300 mm Workpiece height max 80 mm Number of lamps 2 # - changed 10/2023 UV lamp power 120 W/cm² each Speed 2 - 15 m/min variable Transport: Transport carpet Exhaust air connection 2 x 250 mm Connected load 39 kW Weight approx. 750 kg 2 x roller conveyor RB 1300 Working width 1300 mm length 4000 mm Speed 2 - 15 m/min variable Connected load 2 x 0.37 kW Total system length 12450 mm

Condition: ready for operation (used), 1 x Davi round edge rolling machine / plate rolling machine / iron four-roll bending machine / 4-roll machine (English: Davi 4-roller bending machine) Podpfxsymnzbs Ahcera 4 rolls, 3.6 m x 95 mm thick. Video available via WhatsApp/Messenger/Viber. Inspection welcome near D-24983 Handewitt. Year of manufacture 2009 - in operation since 2010. More information available upon request.

Condition: good (used), workpiece weight (max.): 80,000 kg, grinding diameter: 1,580 mm, grinding length: 7,500 mm, Manufacturer: Farrel Type: 60" x 24" Heavy Duty Year of manufacture: 1960 Travelling wheel machine with CROWNING and CONCAVING grinding Equipped with stones / flanches / lubrication / coolant system Maximum diameter full size wheel 1550 mm Work swing over bed 1580 mm Work load 180,000 pounds (81,000 kg) Grinding length 7500 mm Specifications Metric US Standard Center height 930 mm Grinding diameter Ø 1860 mm Grinding length 7500 mm Grinding stone dimensions 1080 x 180 mm Grinding stone speed 400 - 100 rpm Tailstock 260 x 1250 Mk Coolant system Yes filter Yes Dimensions (estimate) length 13200 mm width 4250 mm height 3200 mm weight 80000 kg Please note: The information on this page is given in good faith and to the best of our knowledge, and where possible, has been obtained from the manufacturer, but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details. Share on download Travelling wheel machine with CROWNING and CONCAVING grinding Equipped with stones / flanges / lubrication / coolant system Psdpfxor Ikvme Ahcjra Maximum diameter full size wheel 1550 mm Work swing over bed 1580 mm Work load 180,000 pounds (81,000 kg) Grinding length 7500 mm Center height: 930mm Grinding diameter Ø: 1860mm Grinding length: 7500mm Grinding stone dimensions: 1080 x 180mm Grinding stone speed:400 - 100Rpm Tailstock: 260 x 1250Mk Coolant system: Yes Filter: Yes Length: 13200mm Width: 4250mm Height: 3200mm Weight: 80000kg Aluminum Industry Non-Ferrous Industry Paper Industry Roll Manufactures Steel Industry Plate Mill Hot Rolling Mill Cold Rolling Mill Travelling wheel machine with CROWNING and CONCAVING grinding Equipped with stones / flanches / lubrication / coolant system Maximum diameter full size wheel 1550 mm Work swing over bed 1580 mm Work load 180,000 pounds (81,000 kg) Grinding length 7500 mm Center height: 930inch Grinding diameter Ø: 1860inch Grinding length: 7500inch Grinding stone dimensions:1080 x 180inch Grinding stone speed:400 - 100Rpm Tailstock: 260 x 1250Mk Coolant system: Yes Filter: Yes Length: 519.684inch Width: 167.323inch Height: 125.984inch Weight: 176449.6lbs Aluminum Industry Non-Ferrous Industry Paper Industry Roll Manufactures Steel Industry Plate Mill Hot Rolling Mill Cold Rolling Mill Aluminum Industry Non-Ferrous Industry Paper Industry Roll Manufactures Steel Industry Plate Mill Hot Rolling Mill Cold Rolling Mill

Condition: new, Year of construction: 2026, functionality: fully functional, total width: 2,300 mm, total length: 9,000 mm, total height: 2,300 mm, overall weight: 9,000 kg, Mobile Roll Forming Machine for Frameless Steel Arch Buildings Automatic Production Line for Self-Supporting Steel Hangars and Arch Roofs The mobile roll forming machine is designed for the on-site production of self-supporting curved steel panels used for the construction of frameless steel buildings, arch hangars and self-supporting metal roofs. The technology makes it possible to construct large-span steel buildings without a conventional internal steel frame. Steel coil is formed into a structural profile, cut to the required length and then curved to the required building radius. Several curved panels are connected together using a special seaming machine to form a strong, continuous and self-supporting arch structure. The equipment can be used for the construction of: frameless steel hangars aircraft hangars agricultural buildings grain and machinery storage buildings warehouses industrial buildings workshops garages livestock buildings sports facilities self-supporting steel roofs temporary buildings military and logistics storage facilities Mobile Production Directly at the Construction Site One of the main advantages of this technology is the possibility of producing the complete structural panels directly at the construction site. The main forming and curving equipment is installed on a mobile trailer chassis. The machine can therefore be transported to the building site, where steel coils are converted into finished structural arch panels. This is particularly important for long panels that would otherwise be difficult or expensive to transport. The supplied machine has two axles and eight tyres intended for movement around the construction site. Production Process The complete production process consists of several stages: Prodpoztwx Ujfx Ahcsa Steel Coil → Decoiling → Straight Profile Forming → Cutting to Length → Curving → Panel Seaming → Lifting → Installation The supplied technical manual describes the machine as a combination of a roll forming section and an arch bending section, with electrically driven forming and bending and hydraulic cutting. Main Technical Specifications Parameter Specification Machine type Mobile arch sheet roll forming line Application Frameless / self-supporting steel buildings Feeding width 1000 mm Effective profile width Approx. 610 mm Material thickness 0.8–1.5 mm Forming stations 13 + 1 Straight panel forming speed Up to 15 m/min Arch panel forming / curving speed Up to 13 m/min Seaming speed Approx. 6 m/min Forming motor 7.5 kW Curving / bending motor 5.5 kW Cutting motor 4.0 kW Additional drive 3.0 kW Total installed motor power Approx. 20 kW Cutting system Hydraulic Cutting tool material Cr12MoV, heat treated Roll material 45# steel, chromed and hardened Roller hardness HRC 58–62 Control system PLC Machine dimensions Approx. 9000 × 2230 × 2200 mm Machine weight Approx. 9000 kg Chassis 2 axles / 8 tyres Different Profile Sizes Available The machine can also be manufactured for different structural profile dimensions according to the required building span and application Available configurations may include different: coil feeding widths finished profile widths profile depths steel thicknesses arch radii building spans For example, depending on machine configuration, profiles can be designed for relatively small buildings as well as large-span self-supporting arch structures

Condition: new, Year of construction: 2026, roller (bottom) diameter: 70 mm, roller (top) diameter: 70 mm, side roll diameter: 70 mm, roller length: 1,050 mm, number of digital displays: 1, Equipment: cone bending device, foot remote control, hardened rollers, swiveling upper roller, – Capacity 1050 x 1.8 mm – Bending capacity 1050 x 1.5 mm – Roll diameter 70 mm – Electrically adjustable rear roll – Digital display – Hardened rolls – Conical rolling Predpfxjyp E Sio Ahcoa – Swing-out upper roll – Brake motor – Foot control – Emergency stop – Documentation – 400V

Year of construction: 1995, condition: good (used), 2 Die Thread Rolling machine SENY, Type D-44 EH, Versatile for all types of work, manual and automatic cycles, easily adapted to automating loading,range of cycle times and roll speeds.operating pressure 100Kn, workpiwcw min 3mm max 40mm,lead 3,5 max, pitch of serrations 1,75mm max, roll length 80mm, diameter roll min 80mm max 120mm,roll spindle speeds 47-94, roll spindle diameter 40mm,distance between rolling spindles 80mm minim 165mm max, working stroke 7, feed 0,5mm/s minim 6mm/s maxim, rolling time,variable 0,1-100 seg, swivelling roll spindles +-5º,main motor 3Kw, connected electrical load 4,68kw, tank capacity 150L,aprox weigth 1100kg Pjdpfx Aspwbvkehcera

Condition: good (used), 144 USED Seewer Rondo rolling, rounding, lengthening, and bagging machine. EXTERNAL DIMENSIONS (in cm): - height 170, - width 115, - length: 215, - wing 1x: 108/62, - wing 1x: 75/62, - wing 1x: 114/62. The device is available to verify in our warehouse (36-068 Bachórz, Poland). Paid options available: renovation / transport / assembly / commissioning of the device. The price is a net price. Our languages: ENGLISH, FRENCH, GERMAN, RUSSIAN, UKRAINIAN. ..... bakery oven, bakery ovens, bakery machine, bakery machines, bakery equipment, bakery equipments, bakery device, bakery devices Prodpfjxdkbqex Ahcja

Condition: new, Year of construction: 2026, roller (bottom) diameter: 70 mm, roller (top) diameter: 70 mm, side roll diameter: 70 mm, roller length: 1,050 mm, – Capacity 1050 × 1.8 mm – Bending capacity 1050 × 1.5 mm – Roll diameter 70 mm – Minimum bending diameter 105 mm – Conical rolling – Swing-out upper roll – Brake motor – Foot control – Emergency stop Psdjyrn Ixjpfx Ahcjra – Documentation – 400V

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: EVO, controller model: EVO 4 AXIS 15", number of rollers: 4, roller (top) diameter: 300 mm, roller diameter: 300 mm, roller length: 3,100 mm, working width: 3,000 mm, working height: 1,250 mm, sheet thickness (max.): 30 mm, sheet thickness steel (max.): 30 mm, sheet thickness stainless steel (max.): 25 mm, overall weight: 17,000 kg, total length: 5,500 mm, total width: 2,000 mm, total height: 2,100 mm, power: 18.5 kW (25.15 HP), input voltage: 400 V, number of digital displays: 4, warranty duration: 12 months, Equipment: cone bending device, documentation/manual, emergency stop, hardened rollers, swiveling upper roller, 4roll hydraulic plate bending machine rated capacity 3000x35 mm MODEL MG M3035 , used year 2024 machine as new with warranty included Planetary dual pre-pinch Performance Capacity: Plate width 3000 mm plate thickness rolling 30 mm pre-bend 25 mm minimum rolling diameter ID 350 mm max open width plate feed 3100 mm special top roll reduced size 300 mm to achieve rolling ID 350 mm Power electric motor 18.5kw on hydraulic unit Vac 400/50 -480/60 Installed configuration Hardened rolls high surface strength Conical plate rolling, cone bending Electric console remoted on wheels with joysticks and readout CNC programmable 4 axis controller touch screen 15” Setup virtual infinite rolling programs with teach-in mode and cad/cam operator interface --- Hydraulic motorized driven the central rolls Pre-pinch load adjustable for pre-bend Drop-end top roll front open unloading closed shells Re-rolling system for welded shells calibration. Safety and emergency stop Manuals and schematics machine dimension 5500x2000x2100 mm -weight 17ton --- Additional accessories available with the machine See layout drawing in enclosed nr.1 central support hydraulic 2.2 ton capacity to support large shell dia up to 4,5 meters id Pedpsy Tbf Iofx Ahcsra nr.1 side support hydraulic left side 2.2 ton double arm nr. 1 side support hydraulic right side 2.2ton double arm

Condition: used, Year of construction: 2007, total length: 5,810 mm, total width: 1,980 mm, total height: 1,540 mm, Colour: Blue Empty weight: 11.500 kg Price: On request Psdpfx Aszw A Sujhcjra - Year: 2007 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 600007090 - Drive system: Conventional - Drive: Hydraulic - Number of rolls [pcs.]: 4 - Number of driven rolls [pcs]: 2 - Power [kW]: 15.0 - Max. sheet thickness [mm]: 13 - Max. prebending thickness [mm]: 10 - Max. working width [mm]: 3100 - Top roll diameter [mm]: 280 - Bottom roll diameter [mm]: 280 - Bending speed [mm/min]: 5000 - Options: Cone rolling, Digital readout - Transport dimensions: 5815mm x 1985mm x 1540mm (l x w x h) - Transport weight [kg]: 11500kg - Transport packages [pcs.]: 2 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum