Used Automatic Screwdriver for sale (23,561)

Condition: used, Electric dual-screw unit with automatic feed and pneumatic double stroke, mounted on a handling device, handling system, or manipulator for screwing applications. Screw unit: BÖLLHOFF / BOSCH REXROTH, type UVS-100-2-R-E The Böllhoff Uniquick Vario UVS-100-2-R-E dual-screw unit has a pneumatic double stroke controlled by Festo valves and cylinders. Various monitoring systems are also installed for complete automation. Dweljfx Hyfshccqtsb Screwdriver 1 consists of the following components: Rexroth, type: Servomotor Rexroth, type 0: Planetary gearbox Rexroth, type 0: Encoder Rexroth, type 0: Inline gearbox Screwdriver 2 consists of the following components: Rexroth, type: Servomotor Rexroth, type 0: Planetary gearbox Rexroth, type 0: Encoder Rexroth, type 0: Offset gearbox Dimensions (W x H x D): 165 x 1000 x 200 mm Pneumatic long stroke: 30 mm Pneumatic short stroke: 20 mm Screwdriver spring stroke: 20 mm Last used screws: M6 x 15 mm Electric screwdriver unit Rexroth Servomotor Rexroth Type: EC302 SZ3 Material number: 0 Torque: 0.6 Nm/A Peak torque: 0.7 Nm Speed: max. 20,000 rpm Current consumption: max. 7 A Weight: 0.8 kg Gearbox unit Rexroth Type: 3GE27 SZ3 Material No.: 0 Efficiency: 90% Gear ratio: i=18.9 Torque: max. 10 Nm Weight: 0.4 kg Installation length: 65.5 mm Encoder Rexroth Type: 2DMC012 SZ2 Material No.: 0 Nominal torque: 12 Nm Gear ratio: 1 Efficiency: 1 Weight: 0.55 kg Installation length: 118.5 mm Inline gearbox Rexroth Type: 2GA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Maximum torque: 10 Nm Gear ratio: 1 Weight: 0.2 kg Installation length: 90 mm Offset gearbox Rexroth Type: 2VNA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Maximum torque: 10 Nm Gear ratio: 1 Weight: 0.6 kg Installation length: 153 mm Handling system: JÄGER HANDLING Type: Handy-flex 300 Horizontal movement: 400 mm Vertical movement: 450 mm Load capacity: max. 14 kg Handyflex reach: 250 to 650 mm Handyflex reach when pivoted up: max. 860 mm Rotation radius at full reach: max. 360° Vertical guide column: Ø 30 mm Horizontal guide columns: Ø 20 mm - Balancer for vertical movement - Adjustable load capacity - Adjustable stop for radius limitation Dimensions (L x W x H): approx. 1150 x 650 x 1400 mm Total weight: approx. 90 kg Good condition Without the blue steel pallet as a base plate The blue steel base plate is not included in the scope of supply.

Condition: used, Electric dual-screw unit with automatic feed and pneumatic double stroke BÖLLHOFF Type UVS-100-2-R-E The Böllhoff Uniquick Vario UVS-100-2-R-E dual-screw unit has a pneumatic double stroke via Festo valves and cylinders. In addition, various monitoring systems are installed for complete automation. Technical data: Torque of electric screwdriver: 0.6 Nm Torque of gearbox: max. 10 Nm Speed: max. 20,000 rpm Rated voltage: 3~ 0-230 VAC Current consumption: max. 7 A (per screwdriver) Pneumatic long-stroke cylinder: 80 mm Pneumatic short-stroke cylinder: 20 mm Pneumatic total stroke: 100 mm Screwdriver spring stroke: 20 mm Distance between the two screwdriving tools: 73 mm - equipped with a TORX bit T27 or TP27 (presumably for M6 screws) - a Bosch Rexroth LT303 power module is required to operate the screwdriver. (Power module not included) Dwjljhxvu Ejhccqteb Screwdriver 1 and 2 each consist of the following components: Rexroth Type Servo motor Rexroth Type 0 Planetary gearbox Rexroth Type 0 Encoder Rexroth Type 0 Straight gear Component details: Electric screwdriver unit Rexroth Servo motor Rexroth Type: EC302 SZ3 Material number: 0 Torque: 0.6 Nm Peak torque: 0.7 Nm Speed: max. 20,000 rpm Current consumption: max. 7 A Rated voltage: 3~ 0-230 VAC Weight: 0.8 kg Gearbox unit Rexroth Type: 3GE27 SZ3 Material No.: 0 Efficiency: 90% Gear ratio: i=18.9 Torque: max. 10 Nm Weight: 0.4 kg Installation length 65.5 mm Encoder Rexroth Type: 2DMC012 SZ2 Material No.: 0 Rated torque: 12 Nm Gear ratio: 1 Efficiency: 1 Weight: 0.55 kg Installation length: 118.5 mm Straight gear Rexroth Type: 2GA82 SZ2 1/4"SQ Material No.: 0 Spring travel: 20 mm Spring force: 16 - 34 N Tool holder: 1/4" square Maximum torque: 10 Nm Gear ratio: 1 Weight: 0.2 kg Installation length: 90 mm A motor connection cable of 7m is included. Overall dimensions W x H x D: approx. 180 x 920 x 300 mm Total weight: approx. 20 kg good condition

Condition: used, Year of construction: 2022, Atlas Copco screwing system: Djlhcey U Duhocqtowb PF6000LV IF 14 pcs PF6000 IF 4 pcs ETF-SL21-01-I06-T25 14 pcs HLM1690 4230301080 + QST34-8CT-T50-L150-H6 4 pcs Price per package: 30,000 €

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, For sale: a GEVO SE5-2E/Z machine for window frame manufacturing. The machine was purchased for a specific project that was ultimately not carried out. It was used only a few times, and therefore is in very good working condition. It has been used sporadically since its purchase. Data from the nameplate: Manufacturer: GEVO Dolhccqsy T Eu Hetjwb Type: SE5-2E/Z Serial number: 571 Year of manufacture: 2021 Working pressure: 7 bar Speed: 2500 rpm Country of manufacture: Germany The machine comes from Stolpex – machinery for windows. Selling as used. Condition as shown in the photos. It can be inspected before purchase, by prior arrangement. The machine is ideal for a company involved in the production or processing of window frames.

Condition: like new (used), Year of construction: 2019, functionality: fully functional, PRESSTA CYKLON D double-head automatic screwing machine with all accessories for sale. Djlhccsyziu Tjqtewb Package deal: if purchased together with the WM740 welding line and SMC350 machining center, which are also listed in our ads, the price is EUR 180,000.

Condition: like new (used), Year of construction: 2009, functionality: fully functional, This automatic wrapping machine is specifically designed for use with dry ice slices and/or blocks. All parts in contact with the product are made of stainless steel. Automatic pitch adjustment on the conveyor, and all motors are torque-controlled. The welding temperature is displayed and electronically controlled. The control panel consists of various instruments and visual alarms and is equipped with a self-diagnostic device. TECHNICAL DATA Working speed: Up to 25 wraps per minute, 25 meters of film per minute. Product size: Max wrap width: 250mm, Max wrap height: 60mm, Wrap length: 40 to 260mm, 140 to 580mm, and 200 to 800mm. Dwslhccszxggleqteb Compressed air: 4 to 5 bars Version: standard version is right-hand operated.

Condition: excellent (used), Year of construction: 2019, machine/vehicle number: 1013, REF: MM6216 1 X Comek vertical form, fill and seal bagging machine with Zodiac HS screen Technical specification ⚙️ ✅ Manufacturer - Comek Automatic Packaging Solutions ✅ Model - VPB 330 EVO. ✅ Date of manufacture - 2019. ✅ Weight - 2,500 Kg ✅ Installed power - 10 Kw ✅ Sealing jaws - 330mm (horizontal) x 460mm (vertical). ✅ Overall dimensions - 2000mm long x 1500mm wide x 1800mm high. Note 🗒️ Dslhcsxd Ubnjcqtowb No printer.

Condition: used, Year of construction: 2019, operating hours: 12,000 h, functionality: fully functional, feed length X-axis: 24,000 mm, feed length Y-axis: 450 mm, feed length Z-axis: 1,000 mm, feed rate X-axis: 400 m/min, feed rate Y-axis: 400 m/min, feed rate Z-axis: 400 m/min, total length: 28,000 mm, drilling capacity: 40 mm, rapid traverse X-axis: 10 m/min, rapid traverse Y-axis: 10 m/min, rapid traverse Z-axis: 10 m/min, type of input current: three-phase, control cabinet width: 1,620 mm, control cabinet length: 450 mm, total height: 3,400 mm, total width: 2,600 mm, control cabinet height: 2,200 mm, overall weight: 11,200 kg, workpiece weight (max.): 8,000 kg, positioning accuracy: 1 mm, spindle speed (min.): 200 rpm, rotational speed (max.): 4,000 rpm, spindle speed (max.): 4,000 rpm, rotational speed (min.): 200 rpm, travel distance X-axis: 600 mm, table width: 1,000 mm, drill diameter: 40 mm, compressed air connection: 8 bar, roll diameter: 108 mm, table length: 1,000 mm, table height: 710 mm, power: 21 kW (28.55 HP), Equipment: rotational speed infinitely variable, Complete automatic drill-saw street for profiles APS Europe Profile steel drilling machine RDR-1036 and Band saw RS-1300 Increase your productivity with this complete automatic drill-saw street for profiles. Dwjlhcotnf Iyecqtob Designed to work efficiently and accurately with different profile steel materials. Price does not include disassembly, assembly, transportation and import duties. Please contact us for more information about this machine.

Condition: good (used), IML DA 900 Rigid Box Automatic Wrapping Machine This machine is practically new. Year of manufacture: 2016. Application: Wrapping veneer on a box. Made in Italy. This automated machine is designed for forming solid board boxes by wrapping veneer on a solid board box. This is the latest version of the machine, with a PLC controller. Technical specifications: Djlhccqjzw Ty Nstowb Max size: 430mm x 350mm x 120mm Min size: 60mm x 60mm x 10mm Version thickness: 100-175gsm Weight: 900kg Power supply: 230V The set includes two tool palettes for producing standard boxes. The molds are primarily made using 3D printing technology.

Condition: used, Year of construction: 2021, functionality: fully functional, machine/vehicle number: A/18031, SCHULER - MSP2-800- 4,5x1,8-400 Dsljzxqz Tshccqtowb Kapasite: 800 ton Hava Tüketimi: 30 m³/saat Güç: 296 kW Üst Tabla Ebatları: 4500 mm x 1700 mm Alt Tabla Ebatları: 4500 mm x 1800 mm Pres Yükseklik: 7,5 m Pres En: 6,50 m Pres Genişlik: 4,50 m Dakikadaki Vuruş Sayısı(maksimum): 70 spm Çalışma Reglajı: 300 Kurs Değeri: 80-360 Used machine

Condition: used, Automatic Bag Filling Line Deljyq Tb Iohccqtswb Bag weights from 5kg to 1000kg Infeed with product de-clumper / product breakup breaker and sieve. Incline screw auger to high level hopper and mixer. Delivery system to bag filler where weighing takes place and metal detection before bag filling point. This system comes with a second mobile screw auger for filling 1000kg big bag / sacks Complete with all the controls for the smooth running of this bagging line. After Bagging the bags are sealed with a Saxon Bag Sealer and then stitched with a Singer Bag Stitcher.

Condition: good (used), CMC Ariemat ARM 75 Automatic Cardboard Creasing Machine The machine is fully operational and ready for production. Like new. This highly efficient creasing system is ideal for the production of binders, hard covers, and more. Made in Italy. Sheet feeding is manual, while the machine handles the rest automatically. An automatic feeder can also be added (optional). Parameters are set from the control panel and jobs can be saved to the machine’s memory. Materials processed range from 200 GSM to 4 mm cardboard. Dwjljzw Typehccqteb Sturdy construction, weighs 750 kg. Adjustable creasing and counter-creasing widths. Stepper motor control. Fast operation, up to 2400 sheets/hour. Sheet size: 750 x 1400 mm. Two sheet guides with an extended table and pressure rollers. Quick machine format conversion in less than 1 minute. Receiving table included.

Year of construction: 2017, condition: used, Manufacturer : Transvis Type: Semi-automatic cap screwdriver Application: screwing / capping Year: 2017 Maximum product dimensions: Ø 54.5 x 82 mm Minimum product dimensions: Ø 45.5 x 68 mm Product weight: 90–150 g HMI control panel Asynchronous motor power: 0.18 kW Two-hand control Torque control Overall dimensions: 650 x 1000 x 1800 Screw capper dimensions: 650 x 935 x 990 Weight : 100 kg Spare parts and formats available Power supply: 220V single-phase / 6 bar compressed air Djljy H Rfqjhccqtswb Technical documentation available Video available in running condition

Condition: good (used), TWQ-720RD Automatic Hot Foil Stamping Machine This machine is brand new. Very fast setup. Embossing and hot foil stamping capabilities, with two independent foil feeds. Dslhcjzv Niwjcqtswb Servomotor control for fast and precise operation. Technical specifications: Maximum sheet size: 720x600mm Min. sheet size: 150x120mm Material weight: 120-2000g/m² Maximum throughput: 1200 sheets/h Power consumption: 13kW + compressed air Weight: 2000kg Foil feed: 1-550mm Operating temperature: 50-150°C Power supply: 380V Approximate machine dimensions: 270x160x220cm Equipment: – Control panel with touchscreen PLC – Two independent foil feeds, controlled by stepper motors – Sectional heating plate – Built-in compressor

Condition: used, Year of construction: 2017, Schuler BEUTLER press Type: MC 4000 Year of manufacture: 2017 Pressing force: 4,000 kN Stroke rate: 20-80 strokes/min Dslhszz Abqoccqtswb Stroke adjustment: 40-315 mm Ram adjustment: 200 mm Installed height: 750 mm Table area: 3,000 x 1,400 mm Ram area: 3,000 x 1,300 mm Press weight: 72,000 kg including GSW Schwabe strip feed line Strip width: 80 - 500 mm Strip thickness: 0.8 - 4.0 mm Coil capacity: 5,000 kg

Condition: good (used), WSM Stationary Screwing Unit Assembly and testing of components for car radios and navigation systems. Delhsibicheccqtswb The assembly station is enclosed in a protective housing. The service doors are equipped with monitoring switches with interlocks. The doors are locked during automatic operation and can only be opened during automatic stop or manually after pressing the "Doors" button on the control panel. Automatic operation cannot be started with a door open. Operational Sequence The station is loaded with the pre-assembled component via the transfer belt. The following describes the operation steps of the automatic station with a transfer belt. In normal operation, all three stations operate in parallel. - Positioning the test unit (WT) with the pre-assembled module in station 2.1 - Lowering the carrier with the scanner and vision sensor - Scanning the 3 codes (front panel, front PCB, SD PCB), comparison with the database - Checking the correct locking of the FFC in the connector - Raising the carrier and lowering the test unit onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.2 - Positioning the screwdriver and screwing the front PCB in place - Lowering the test unit (WT) onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.3 - Lowering the light shield and making contacts, adjusting the carrier with the test sensors from below - Type-dependent testing of the SD + CD slot lighting and buttons - Functional test of the CD eject button - Lowering the test unit (WT) onto the conveyor belt > continue If errors occur during testing, they are displayed on the screen. and can be repaired if possible. For this, the system is switched to manual operation and the doors are opened. After the repair and restarting the automatic system, the workpiece carrier is tested again in the station. If a repair is not possible (e.g., due to a screw error), the workpiece carrier is marked as NIO (Not Okay) in the control system and is not processed further. Manual NIO marking and rejection is also possible. Financing through our bank is also available. komplett-konzept.leasingo.de More assembly stations, new and used, can be found in our shop! International shipping costs on request!

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, overall weight: 3,500 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Cutting range at 90° (round): 530 mm Cutting range at 90° (flat): 530 × 800 mm Cutting range at 45° (flat): 530 × 520 mm Cutting range at 30° (flat): 530 × 320 mm Cutting angle: 45° - 0° - 60° Blade speed: 20–120 m/min Feed length: 1,500 mm Dwolhezyccxoccqtjb MACHINE DETAILS Saw motor power: 3.0 kW Coolant pump: 100 W Hydraulic pump: 370 W Power connection: 400 V / 50–60 Hz Dimensions & Weight Dimensions (L × W × H): 2,500 × 4,000 × 2,500 mm Total weight: 3,500 kg EQUIPMENT Machine stand with chip collection tray Hydraulic cutting pressure control Stepless blade speed control Hydraulic guide arm adjustment Minimum quantity lubrication Automatic shutdown at the end of the cut Chip brush Hydraulic miter adjustment Hydraulic clamping device Hydraulic blade tensioning Operating manual

Year of construction: 2006, condition: used, functionality: fully functional, We present an Automatic drawer slide insertion line of 3 machines and robot (currently in production): BLA - B41, manufactured 2006/2007 (Sweden) BLA - B28, manufactured 2006 (Sweden) Screwdriver 3RL, manufactured 2018 (Lithuania) Robot Dslhcjy T Nfiscqtswb TECHNICAL SPECIFICATIONS Inserting of Drawer Slides Fitting machine BLA-B41 – pos. 1 Fitting machine in pass-through outfit, equipped with positioning stop, designed for automatic screwing of drawer slides. The fitting machine is designed for following sizes of material: Deep: 300–600 mm, servocontrolled adjustment Height: 400–1500 mm, servocontrolled adjustment Thickness: 16 mm Dimensions Machine length: 4100 mm Pass-through height: 900 mm Screwdriver equipment Screwdriver beams, 2 units, each equipped with 2 screwdrivers and corresponding screw feeders for Ø6.3x13 screws. A suiting screw is the type 84 FSX Magazine units 2 magazine units designed for left drawer slide 2 magazine units designed for right drawer slide · Each magazine contains approximately 40 drawer slides. · The length of the slides are 450 mm and the width 21.5 mm. Buffer conveyor TPB – pos. 2 Driven roller conveyor Total length: 2150 mm Other specifications are the same as for pos. 3 above. Buffer conveyor TPB – pos. 3 Driven roller conveyor Total length: 2450 mm Roll length: 600 mm (620 mm inside conveyor frame) Roll pitch: 150 mm Roll type: Ø50 mm steel, coated with thermoplastic rubber Speed: 0.78 m/sec. at 50 Hz (frequency controlled) Height: 900 mm Returning Conveyor System TPT-US – pos. 4 Sideway section with four belts Speed: 0.5 m/sec. at 50 Hz (frequency controlled) Driven roller conveyor Total length: 8900 mm Roll length: 600 mm (620 mm inside conveyor frame) Roll pitch: 150 mm Roll type: Ø50 mm steel, coated with thermoplastic rubber Speed: 0.50 m/sec. at 50 Hz Height: 900 mm Additional specifications Sound pressure level Lower than 70 dB(A) Connection facts electrical With reference to the electrical drawings Connection facts pneumatic 0.63 MPa (6.3 bar), ½”

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, We are offering several Dürkopp Adler industrial automatic pocket sewing machines from our garment production facility. The machines are designed for the automatic production of piped, flap, and welt pockets and are suitable for industrial trouser, jacket, and garment production. Dwolhszzkuroccqtob Machines available: • Dürkopp Adler 739 991001 K3 – BVL Automatic 2015 • Dürkopp Adler 745-34-2A – Piped/Welt Pocket Automatic – 30 mm – 2 units • Dürkopp Adler 745-34-2B – Automatic Pocket Sewing Machine – 10/16 mm • Dürkopp Adler 1970 Automatic Sewing Unit for attaching pocket facings The Dürkopp Adler 745 series is designed for the automatic sewing of piped pockets, flap pockets, and welt pocket openings. Depending on the machine configuration, the units are equipped for different pocket widths and production applications. The machines come from an industrial garment factory and were used in professional production. Important: This advertisement covers several machines. The main machine advertised is the Dürkopp Adler 745-34-2B, but the other machines listed above are also available for sale individually or as a package. Photos in the advertisement show the different machines currently available. Location: Romania Quantity: Multiple machines available Sale: Individual machines or complete package Price: On request / depending on machine and quantity Inspection of the machines can be arranged. For serious buyers, additional photos, machine identification details, and videos can be provided upon request. We are open to offers for individual machines as well as for the complete package.

Condition: good (used), Year of construction: 1989, double-sided processing from 280 to 2500 mm the following equipment is available on each side: saw drilling head with 3 drills dowel inserter Delhcjzzprpecqtjwb 3 drilling units from above, at the front 2 drilling units from above, at the rear return transport from below

Condition: good (used), Renz Mobi 500 Semi-Automatic Spiral Binding Machine Perfect condition, manufactured in 2021. Only 3,636 bindings used. Delhcozur Hiocqtswb Semi-automatic spiral binding machine from the German company RENZ: • Controlled by a touchscreen display • The fastest setting changes for various work formats in this class via an electronic panel, which is particularly important for small, frequently changing runs • Spiral diameter adjustment from 1/4″ to 1 1/4″ (6.9 to 32.0 mm) using a knob • KA-300 Hanger Feeder • Quiet operation. The machine does not require a compressor. • Working width: 105-500 mm • Mobile, easy to move • Includes a receiving table • No special operator training required 230V power supply Weight: 550 kg

Year of construction: 2021, condition: ready for operation (used), functionality: fully functional, EV Car Motor Assembly and Testing Line (2021) Designed to produce EV motors in the power range of 180–300 kW Including manual, semi-automated, and automated operations Cycle time: 86s Stations and Equipment Component loading - KUKA KR15 R2700-2/FLR robot (2021) - Material infeed - Inner housing heating with induction coil up to 240 °C - Stator pressing into housing - 1T TOX press - Keyence CA-DQP25X - Cooling tunnel - Cooldown to 24 °C - Cycle time: 600 s X-ring and D-ring inner housing assembly - X-ring and D-ring seal insertion into housing - Dedicated round assembly tool available Outer housing pre-assembly - Flange screw into housing with Bosch Rexroth ESA013G-G0 screwdriver - Automatic inner and outer housing joining Outer housing assembly - 3T TOX EQK 030 press - 2x Cognex scanners - 2x Keyence Camera V3 - 3x VS camera systems Rotor magnetization and measurement - Magnet magnetization - MagSys magnetizer MC3K82 (2020) - Magnetizing fixture MFFer8/160/250 A-shield pre-assembly and rotor insertion - Rotor bearing and resolver pressing - 3T TOX press A-shield assembly into outer housing - 1T TOX EQK press Delhcszhub Aecqtewb - A-shield screwing into outer housing with pneumatic screwdriver (5 Nm) Mounted component fastening - Fastening with 4GE59 Rexroth screwdriver - Manipulator system Handyflex 400 Inter-connector connection - Manual mounting of inter-connector and insulating tube Counter ring insertion, cooling cover, and vent assembly - 3T TOX EQK 030 press Rotor cooling cover mounting - Screwing with 4 Nm End-of-line (EOL) electrical testing loop - 5x Deutronic testers, including: - ETL ATS 400 high-voltage testers - HIOKI RM3545 resistance testers - Reilhofer EOL analyzers Inter-connector disconnection station - Disconnection of the inter-connector - Insertion of 2 screws and screwing with Rexroth screwdriver (13 Nm) - Manipulator system Handyflex 300 - Washer control - Motor rotation Leak testing - 2x Leak test stations with Innomatec LTC-902 testers - Vacuum and overpressure leak tests - Tested quantity: approx. 50,000 pcs per test station Rotation, laser marking, stamping, engraving, and inspection - ADT stamping machine - Arex Laser 450 - Keyence CA-H camera system - Datalogic CBX 100 reader - Tested quantity: approx. 130,000 pcs Transportation protection - Yellow transportation cover/cap and plug assembly - Manual insertion of caps and hole securing Packaging and final inspection - Dalmec manipulator (2022)

Condition: used, CNC lathe INDEX C200 Dslezz Aymshccqtswb

Year of construction: 2020, operating hours: 10 h, condition: like new (used), functionality: fully functional, Automatic line for rinsing, filling, pasteurizing, drying and packaging of glass juice bottles consisting of following modules: 1. SEMI AUTOMATIC DEPALLETIZER (model: Depal 512 – mini) for unpacking glass bottles from pallets, 1 operator required to put the pallet into the machine and remove the cardboard that is inserted in between the glass bottle layers 2. UNIVERSAL RINSING MACHINE (model: IND-Wash 56 S2) for steam sanitizing and hot water rinsing of the bottles before filling Dwjlhcjzdr Ilocqteb 3. ROTARY FILLING MACHINE (model: IND-Dose 46 PO-12) for filling of the hot product into the glass cylinder shape bottles 4. CLOSING MACHINE FOR TWIST OFF CAPS (model: IND-Close 12E) for vacuum closing of the filled bottles using steam injection induced vacuum system 5. PASTEURIZATION AND COOLING TUNEL (model: PT 42-9) for further continuous pasteurization of the product 6. VACUUM TESTING MACHINE (model: IND-Test 61) for selection and eviction of the improperly closed bottles 7. DRYING MACHINE (model: IND-Blow 86) for drying the residual moisture on the battle surface before applying labels 8. LINEAR LABELLING MACHINE FOR APPLICATION OF SELF-ADHESIVE LABELS (model: IND-Lab 32B) with top (over the cap) and side application of the labels on cylindrical bottles 9. AUTOMATIC GROUPING AND SHRINK-WRAPPING MACHINE WITH TRAY AND FILM (model: IND-pack 29 T) for packing the bottles onto cardboard trays in various configurations per different bottle sizes 10. SET OF FLAT TOP CHAIN CONVEYORS (model: IND-Trans 71) connecting the various modules of the line (conveyors between rinsing, filling and closing sections with top covers)

Condition: new, Year of construction: 2021, New 4 Head Automatic Capper & Cap Feeder Never Used / New Model RCP-141 To include Capper Feeder & automatic capper machine Dwslev R I D Hshccqteb