Veneer press

JOOS

Condition: good (used), functionality: fully functional, machine/vehicle number: 12638, electrically heated, with tread strip, gold-anodized panels, Kledpfx Ahjybbm Tj Nsl dimensions 2500 x 1350 mm, in very good condition Price ex location Transport available at extra cost!

Condition: good (used), Year of construction: 2004, machine/vehicle number: A II 151768, Offer 25979 - Operating hours 16550 h - Operating pressure 10 bar - Delivery rate 15.9 l/s - Drive 400 V / 7.5 kW - Motor speed 3000 rpm - Air tank 250 L - Required space approx. W 700 x H 1830 x D 1050 mm - Weight approx. 250 kg Kjdswrcq Nopfx Ah Nell

Condition: excellent (used), Catalogue number 7740 TECHNICAL SPECIFICATIONS - heating plate dimensions: 3000x1350 mm - number of loads: 1 - electrically heated shelf - clearance: 340 mm - number of cylinders: 6 - cylinder diameter: 80 mm - total power: 20.7 kW - pump motor: 1.1 kW - dimensions (L/W/H): 3570x1600x2200 mm - weight: approx. 3500 kg Ksdpsx S Ebdsfx Ah Nsll ADVANTAGES – made in Germany – electrically heated shelves – unpainted – in impeccable condition – used press Net price: 48,900 PLN Net price: 11,650 EUR at an exchange rate of 4.2 EUR (Prices may vary with significant fluctuations)

Condition: excellent (used), Shelf length: 250 cm Width: 130 cm Four actuators Kledpfjxgnp Dsx Ah Nel

Condition: new, Electrical voltage 400 V Frequency 50 Hz N° Phases 3 / 3 Ph Mass 486 Kg Kedpfjd R Uz Tox Ah Nell Dimensions sheet 2700 x 27 x 0.9

Condition: good (used), pressing force: 95 t, cylinder diameter: 90 mm, plate width: 1,350 mm, Veneer press Joos Type: HP 90 with 2 intermediate plates, stacking automaton and scissor lift table Pressing area: 2,550 x 1,350 mm Working surfaces: 3 pcs. Intermediate plates: 2 pcs. Pressing force: 95 t Piston diameter: 90 mm Specific pressing pressure: 2.75 kg/cm³ Number of cylinders: 4 Heating medium: hot water Kjdsxnqq Hjpfx Ah Noll Total power: 1.3 kW Safety device: emergency cord Dimensions of the press: 3,000 x 1,530 x 2,200 mm Weight of the press: approx. 4 t Elkom heating plates in very good condition Scissor lift table The plates are automatically stacked and thus discharged.

Condition: used, Year of construction: 1995, Used Machine Year of manufacture: 1995 Features and technical data: - Total pressing force: 70 t - Press area: 2500x1300 mm - With gold anodized plates in good condition - Press chamber height: 400 mm - 4 cylinders, diameter 80 mm - ABS safety system, can be deactivated - Emergency cord - Extendable support, left side - Swivel button operation - Hydraulic unit at the bottom - Cleaned and assembled/pressed by ELKOM staff Dimensions: 2900 x 1480 x 2050 mm Kodpfx Aex Enr Sjh Njll Weight: 2950 kg Availability: short-term Storage location: 63934 Röllbach

Year of construction: 2015, condition: used, Dimensions (L/W/H) 700x655x1400 mm Filter capacity / m² Number of filters 1 St. Number of dust containers 1 St. Kjdegr Rkxopfx Ah Noll Weight 140 kg

Condition: used, Year of construction: 1976, pressing area: 2500mm x 1250mm opening: 360mm heating plate top: elektric heating plate bottom: defective plate surface: ALU - anodized pressure: 90t number of cylinder: 4 Kljdpfjx Edl Eox Ah Nel electricity: ca. 33A machine length: 3000 mm machine width: 1500mm weight: 4000kg

Condition: used, Year of construction: 2024, Version: Joos A.B.S. safety system to protect the heating plates in case of incorrect loading or parts left behind. The press is open on all sides, features a robust all-steel construction, and is protected against overload. The maintenance-free hydraulic system is integrated into the oil tank. Step-less pressure adjustment is performed according to a clear pressure diagram. Once the set pressure is reached, the system switches off automatically. Constant pressure is maintained throughout the entire pressing process. The rack-and-pinion guide ensures stable parallel travel of the pressing plates. The press is optimally suited for laminating flat surfaces using adhesives, provided the corresponding technical requirements are met. Technical Data: - Max. pressing force: 1200 kN - Adjustment range: 10 – 100% - Total pressing area: 3100 x 1350 mm - Specific pressure at full capacity: 3.0 daN/cm² (kg/cm²) - 6 cylinders, 80 mm diameter, 400 mm stroke - Hydraulic working pressure: 398 bar - Press room height: 400 mm - Color: Light grey, RAL 7035 Hydraulics: The following components are integrated into the press's hydraulic system: - 1 oil-hydraulic two-stage high-pressure pump - 1 three-phase motor, 2.2 kW - 1 automatic pressure switch - 1 change-over valve - 1 pressure diagram The hydraulic unit is built into the lower section of the press. Controls: Automatic pressure control via electronic controller with setpoint and actual value display. Operation is performed via a clear control panel. The control cabinet is fully integrated lengthwise in the upper section of the press. Kjdpfx Ahsxplbco Njll Operating voltage: 400 V, 50 Hz, 3-phase. ELECTRIC HEATING PLATE 3100 x 1350, GOLD ANODIZED One lower and one upper electric heating plate, 3100 x 1350 mm. The surfaces are anodized, making them extremely hard, scratch- and abrasion-resistant. High-temperature insulation between the heating plate and the press table. Maximum operating temperature: 120°C. (1 section / 2 heating plates.) TEMPERATURE CONTROL Temperature control R 1.1; each heating plate features an electronic temperature controller and a safety temperature limiter around the edge of the heating plate. SWIVEL PANEL OPERATION Operation is via an ergonomic swivel panel control. Location: Rieth

Year of construction: 2013, condition: ready for operation (used), A Rehm Invertig Pro 350 AC DC and a Rehm Invertig Pro 450 DC are available, used and in good condition. 1) Invertig Pro 350 AC DC, standards: IEC 60 974-1 IEC 60 974-2, welding current range TIG: 3-350A, output voltage U₂ at maximum current: approx. 24V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent for TIG at 350A, mains voltage input: three phase 400V 50Hz, protection class: IP23S, protection category: S, setting range: 3-350A for TIG in this AC DC version, duty cycle 100 percent at 40°C 350A for TIG 100 percent duty cycle, input fuse protection: 32A at 3x400V for the 350 AC DC version, length: 520mm, width: 360mm, height: 460mm, weight: 29.5kg for AC DC version. 2) Invertig Pro 450 DC, standard: IEC 60 974-1, welding current range TIG: 3-450A, output voltage U₂ at maximum current: approx. 28V, open circuit voltage U₀: approx. 91V, duty cycle 100 percent at 450A TIG, lower for electrode welding approx. 60 percent, mains input: 3x400V 50Hz, protection class: IP23S, duty cycle at 100 percent 450A TIG at 40°C, electrode welding current approx. 360A at 100 percent duty cycle for electrode in the 450 DC version, input fuse protection: 32A at 400V three phase for 450 versions, length: 520mm, width: 360mm, height: 460mm, weight: approx. 28kg. An on-site inspection is possible. Ksdpfx Ahoxddame Nsll

Condition: good (used), Year of construction: 1975, Veneer press - 3300 x 1350 mm - External dimensions: 4000 x 1650 x 2450 mm - Year of manufacture: 1975 - Approx. 5500 kg - Electrically heated platen, no dents - HP 120 Ksdpex Akuzofx Ah Njll - Press area height: 400 mm - 6 cylinders - Rack and pinion guide

Condition: good (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 1855680, pressing force: 80 t, input frequency: 50 Hz, power: 4 kW (5.44 HP), table length: 1,400 mm, table width: 800 mm, operating pressure: 270 bar, Manufacturer: Joos Model: HP-S 80 Year of Manufacture: 2004 Pressing Power: 800 kN Three-Piston Suitable for woodworking and industrial applications Well-maintained and in good working condition Klsdpfx Aorp D Eajh Nol Previously used in a company setting, reliable and durable. Despite the dust, this Hydraulic Press continues to deliver reliable performance. Contact us today to arrange a viewing or to inquire further information.

Condition: excellent (used), Gold anodized panels Working dimensions 2.5 x 1.1 m Electric heating Fully functional, tested You can call or write to us. We speak and write German and Russian. Kodju I N D Hepfx Ah Njll You can also send messages in English. 31.3.5

Condition: used, Used machine Features and technical data: - Press area: 2,200 × 1,100 mm - Number of cylinders: 4 - Max. pressing force: 60 tons - Version: single deck - Heating plates: gold anodized ELKOM energy-saving plates - Opening width: 350 mm Klsdpjwpm I Hjfx Ah Nsl - Connected load: 14 kW - Piston diameter: 80 mm - Operating pressure: 365 atü Dimensions: 2,600 m × 1,250 m × 1,750 mm Availability: short-term Location: Röllbach