Used edgebanders for sale (570)

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Hedpfx Asyqybuohvofd Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Hedpoyqx U Hjfx Ahvjfd Motor power: 10.5 kW Automatic tool changer MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: ready for operation (used), Year of construction: 2011, machine/vehicle number: AH/335516, functionality: fully functional, input voltage: 400 V, input current: 68 A, Equipment: CE marking, TECHNICAL DETAILS Number of processing units: 10 1st unit: Spraying device Tools included 2nd unit: Glue applicator 3rd unit: Pressure rollers Tools included 4th unit: End trimming unit Tools included 5th unit: Rough milling unit Tools included 6th unit: Corner rounding unit Tools included 7th unit: Radius scraping unit Tools included Hjdpfxsyuylus Ahvsfd 9th unit: Flat scraping unit Tools included 10th unit: Brushing unit Tools included MACHINE DETAILS Voltage: 400 V Current consumption: 68 A Number of transport packages: 2 EQUIPMENT CE marking

Condition: ready for operation (used), Year of construction: 2020, machine/vehicle number: 20.082, functionality: fully functional, power: 16.2 kW (22.03 HP), input voltage: 400 V, total height: 1,670 mm, total length: 6,000 mm, overall weight: 2,200 kg, TECHNICAL DETAILS Number of machining units: 10 1st unit: Pre-milling unit Tools included 2nd unit: Glue application unit 3rd unit: Pressure rollers Tools included 4th unit: End trimming unit Tools included 5th unit: Rough trimming unit Tools included 6th unit: Corner rounding unit Tools included 7th unit: Fine trimming unit Tools included 8th unit: Corner rounding unit Hodpfxsyuyfze Ahvjfd Tools included 9th unit: Radius scraper unit Tools included 10th unit: Brushing unit Tools included MACHINE DETAILS Voltage: 400 V Power: 16.2 kW Dimensions & Weight Dimensions (L x W x H): 6,000 x 1,415 x 1,670 mm Machine weight: 2,200 kg EQUIPMENT CE marking

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, input voltage: 400 V, input current: 42 A, total height: 1,800 mm, total length: 4,800 mm, total width: 1,000 mm, Equipment: CE marking, TECHNICAL DETAILS Number of units: 9 1st unit: Pre-milling unit Tools included 2nd unit: Glue application unit 3rd unit: Pressure rollers Tools included 4th unit: End trimming unit Tools included 5th unit: Corner rounding unit Tools included 6th unit: Radius scraper unit Tools included 7th unit: Corner rounding unit Tools included 8th unit: Flat scraper unit Tools included 9th unit: Buffing unit Tools included MACHINE DETAILS Voltage: 400 V Current: 42 A Dimensions (L x W x H): 4,800 mm x 1,000 mm x 1,800 mm EQUIPMENT Glue pot Hodpfx Ahoyux Rijvofd

Condition: ready for operation (used), Year of construction: 2013, machine/vehicle number: 200.04.007.13, functionality: fully functional, power: 11 kW (14.96 HP), workpiece height (max.): 60 mm, total height: 1,700 mm, total length: 4,800 mm, total width: 900 mm, TECHNICAL DETAILS Workpiece height min.: 8 mm Workpiece height max.: 60 mm Hfedpfx Asyux Egohvjd MACHINE DETAILS Power: 11 kW Mains voltage: 400 V Current: 28 A Phases: 3 Frequency: 50 Hz Dimensions & Weight Dimensions (L x W x H): 4,800 x 900 x 1,700 mm Machine weight: 1,250 kg EQUIPMENT Multi-function milling unit Glue application unit

Condition: used, OTT Tornado - TOP Control - via a 15-inch color touch monitor for full automation and maximum operating comfort CM CombiMelt gluing system suitable for processing EVA and PUR hot-melt adhesives as well as all common cleaning granulates Joint processing unit for attaching chipboard panels Automatic roll magazine Automatic edge magazine Double end trimming unit with automatic swiveling 0° / 3° Hfsdpfxsyuvblo Ahvjd Flush milling unit - for flush trimming - 12mm Fine radius milling unit - profiling knives R2 - R5 Automated copying milling - corner rounding Scraper unit - radius - bevel Surface scraper unit Sliding agent spray device - PU Cleaning set with fine buffing unit Very stable workpiece support with roller conveyors - FRONT with scissor extension Complete tool equipment included Machine is AS NEW in EXTREMELY WELL-MAINTAINED CONDITION Machine from retirement Initial commissioning in 2009, very few operating hours Leasing option available In stock in Lieboch

Condition: used, Year of construction: 2016, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, height adjustment type: mechanical, overall weight: 450 kg, – Italian production – year of production 2016 – pre-milling – DTR, CE TECHNICAL PARAMETERS: – edge thickness: 0.5 - 3 mm – wooden edgeband: 0.5 - 5 mm – element height: 8 - 50 mm – minimum edgebanding length: 160 mm Hfjdswb Ha Tspfx Ahvjd – minimum board width: 110 mm – feed speed: 7 m/min – pre-milling – radial cutters – edge cutting – radial scraper – straight scraper – blower for each unit – working pressure: 8 bar – working machine length: 2030 mm – transport dimensions (length/width/height): 330/80/125 cm – weight: 450 kg

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,3 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 20 Panels thickness (min/max) mm 8 / 60 NEW (in 2024) Numerical Control EDGETEQ MOD - Power Touch (WoodCommander) Adjustable Feeding speed up to 25 m/min In-feeding system EZ 14 Spraying unit (Anti-sticking liquid) In-feed fence, adjustable by N.C. Pre-milling Unit (vertical joint trimmers) 2 x Kw 3 Glueing Unit (P.U.R. Glue + Quick Melt system) Band Pressure zone, adjustable by N.C. Edge coils supporting unit (with No. 2 reels) Snipping (end-cutting) unit HL 84 (2 x Kw 0,5 ca.) Pneumatic swivelling and adjustment Rough Trimming unit BF 20 (2 x Kw 1,5 ca.) Multi Function Unit (Profile contour Trimming) FK 11 (2 x Kw 0,4 ca.) Profile edge scraping unit Hsdpeyt Izbefx Ahvefd Finish processing unit (Glue scraper + Buffing unit) FA 11 Panels Return System "LIGMATECH" Mod. ZHR 541/L/095 (with Portal bridge and 360° rotating vacuum head)

Condition: used, Year of construction: 2018, Edge banding machine AKV 3006 DK - F with jointing unit, including DIA tools • Jointing capacity up to 40 mm • Workpiece thickness up to 3 mm • Combination milling station, radius R 2.5 mm Technical Description: - Hot melt adhesive application to the workpiece for edge materials up to 3 mm - Workpiece thickness up to 60 mm without jointing unit, up to 40 mm with jointing unit - Maintenance-free, coated gluepot - HF end-trimming unit (16,000 rpm) for front and rear edge overhang - HF milling station (16,000 rpm) with replaceable cutter heads (combination version) and fine adjustment from the operator side - Free spaces for additional processing units (Hebrock system) - Feed speed approx. 10 m/min - Cutting depth adjustment of the end-trimming saw - Signal lamp for workpiece flow - Robust chain feed Hjdpex S Hmzjfx Ahvjfd - Ergonomically arranged control panel - Double roller upper pressure beam - Aggregate windows on machine rear and operator side - PLC control with touchscreen included Technical Data: - Feed rate: 10 m/min - Panel thickness: 8 – 40 mm - Weight: approx. 1550 kg (depending on configuration) - Dimensions (L x W x H): 5250 x 1445 x 1600 mm Airtronic incl. cooling and antistatic spray system (2014) • 1 pc hot air unit for visual zero joint using special edge materials • Including pneumatic gluepot positioning • Including cooling and antistatic spray system • Including 2 additional quick-change edge channels • Including special version corner rounding unit; max. workpiece thickness 60 mm, min. length 200 mm - Exclusively for Hebrock 3000 series edgebanders - Retrofitting possible at extra cost upon request Technical Data (special unit): - Max. panel thickness: 40 mm - Edge thickness: 1.2 – 2.0 mm - Feed speed: 7 – 10 m/min - Air consumption: approx. 280 – 580 l/min (only Airtronic), electronically controlled - Ready for operation after approx. 2 min Upgrade to 8 mm edge thickness possible; max. workpiece thickness 40 mm • Including pneumatic saw adjustment (special version, min. workpiece thickness 8 mm) • 3-point pneumatic milling shift • Selector for radius/chamfer/flush for combination milling stations, eliminating manual changeover (PLC control required) Buffing station (swab): 1 pc Corner rounding unit: 1 pc incl. combination tooling and pneumatic radius/chamfer adjustment, max. 40 mm workpiece thickness, min. 300 mm workpiece length, Radius R 2.0 mm Radius scraper: 1 pc with pneumatic lift, Radius R 2.0 mm Flat scraper: 1 pc with pneumatic actuation Complete chassis: 1 pc Glue station quick-change system incl. glue discharge system (downward outlet in preparation), 1 pc (no second gluepot), machine can process PU adhesive Grooving unit (vertical for panel): 1 pc incl. pneumatic lift, vertical groove, groove width 8.2 mm, groove depth 8.0 mm, distance from panel edge 14.0 mm; special motor version with higher performance Extraction for internal jointing unit: 1 pc connected to machine's extraction manifold Corner rounding cutter ball bearings: 24.1 mm (1 pc), 24.2 mm (1 pc) Edge protection spray system: 1 pc for sensitive edge materials Combined spray system (separating and cleaning agent): 1 pc Location: Supplier stock

Condition: excellent (used), Akzent edge banding machine V31 Hfedpfx Aoytw Ttehvod - Dimensions: 1750 x 530 x 600 mm - Plus additional 600 mm Ø roller table - Milling motor with disc cutter - Workpiece thickness: 10-55 mm - Edge thickness: 0.4-1 mm - 220 Volt - 3.3 kW - Weight: 135 kg

Condition: not inspected (used), Year of construction: 2014, functionality: unexamined, power: 25 kW (33.99 HP), workpiece height (max.): 60 mm, edge thickness (max.): 12 mm, feed rate X-axis: 18 m/min, Equipment: CE marking, TECHNICAL DETAILS Hfsdpeytr Rgofx Ahved Minimum panel height: 8 mm Maximum panel height: 60 mm Minimum edge thickness: 0.3 mm Maximum edge thickness: 12 mm Maximum feed speed: 18 m/min Sequence of work steps: Section 1 Work step: Positioning Motor power: 2.5 kW Automatic control Edge preheater Glue tank Glue preheater Roll magazine Section 2 Work step: Cutting Number of motors: 2 Section 3 Work step: Edge milling Number of motors: 2 Motor power: 0.55 kW NC positioning Section 4 Work step: Corner rounding Number of motors: 2 NC positioning Section 5 Work step: Milling Number of motors: 1 Motor power: 3.5 kW Section 6 Work step: Edge scraping Section 7 Work step: Glue scraping Section 8 Work step: Brushing Number of motors: 2 MACHINE DETAILS Total power: 25 kW EQUIPMENT Panel support guide Spraying unit Control with more than 20 control systems CE marking The machine is sold and delivered in its actual and legal condition ('as seen and agreed'), based on photo documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 6216

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Hfedpfx Ahoytr Hbsvod Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: used, Year of construction: 2013, Used machine Year of manufacture: 2013 Equipment/features: - Machine table with 13 running rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with cutter (for cuttable edges) - Three pressure rollers - Belt feed motor 0.25 kW; approx. 1250 mm length; feed rate approx. 6.0 m/min; 50 mm wide timing belt with thick, workpiece-friendly rubber coating. Digital counter for height adjustment - Direct glue application to the workpiece: leakproof glue pot with glue supply from below and fast heat-up time after machine stoppage - Flush trimming unit for front and rear workpiece edges, automatic sensing at the workpiece, pneumatic trimming with a cutter for cuttable edges - Flush milling unit with vertical sensing and horizontal guidance, reproducible adjustment via digital counters, 2 high-performance 0.4 kW high-frequency motors, continuously adjustable from 4000 to 18000 rpm, cutter diameter 70 mm, Z4, radius 2 mm/15°; central extraction connection Ø 100 mm, 2 chip extraction hoods with hose Ø 60 mm - Automatic height adjustment of the upper cutter with the belt feed - Continuous workpiece support approx. 1800 mm long, workpiece support rail extendable by approx. 300 mm - Rotatable film disc Ø 800 mm Technical details: - Minimum workpiece width: approx. 80 mm - Workpiece thickness: 10 – 50 mm - Minimum workpiece length: approx. 220 mm - Edge thickness: 0.4 – 2.0 mm - Roller separation max.: 1.0 x 55 mm, 2 x 45 mm - Glue pot heating power: 2.7 kW - Electrical connection: 400V, 50 Hz, 3Ph + N - Total connected load: 3.8 kW - Heat-up time: approx. 10 minutes - Pneumatic connection: 6 bar - Working height: approx. 880 mm - Dimensions: approx. 1800 x 700 x 1300 mm (without film disc Ø 800) - Net weight: approx. 260 kg Availability: short-term Location: Flörsheim Hjdeytkiuspfx Ahvjfd

Condition: ready for operation (used), Year of construction: 2006, Edgebander manufactured in 2006. This HOMAG Optimat KAL 330 features a flexible production layout for furniture parts, accommodating workpiece dimensions from 250 to 3000 mm in length and 120 to 1200 mm in width. It includes a single-sided edge banding machine capable of processing various edge materials up to 20 mm thickness. If you are looking to get high-quality edge processing capabilities, consider the HOMAG Optimat KAL 330 edgebander we have for sale. Contact us for further details. • Line workpiece capacity: • Length 250–3000 mm • Width 120–1200 mm • Thickness 8–60 mm • Edge bander (KAL 330) — base and transport Hsdpoytf Irofx Ahvefd • Continuous machine base; workpiece support with roller bar extendable ~800 mm • Transport chain 80 mm wide with rubber surface; precision guidance, hardened surfaces • Top pressure: driven belt • Technical data: • Feed speed 18–25 m/min • Working height 950 mm • Minimum working width: 55 mm at 22 mm thickness; 100 mm at 60 mm thickness (depending on workpiece length) • Workpiece overhang/supernatant 30 mm • Workpiece thickness 12–60 mm • Edge material from strip: 0.4–20 mm (max cross-section 900 mm²) • Edge material from coil: 0.3–3 mm (max cross-section: PVC 135 mm², veneer 100 mm²) • Max coil diameter 830 mm • Pneumatic connection 7–8 bar • Infeed system and controls (integrated with KAL 330) • Flexible workpiece infeed system wz10 for automatic infeed (lengthwise and crosswise); for precisely sized, square parts • Stepless infeed guidance adjustment (axis), speed set at input terminal • Automatic side adjustment of units (workpiece overhang 30–80 mm) for gluing and post-processing • Input terminal; solvent applicator top/bottom • Edge preparation and gluing • Pre-milling unit: 2 motors, each 4 kW, 150 Hz, 9000 rpm; electro-pneumatic control • Stepless vertical axis SF20 for automatic centering to panel thickness • Pre-melting unit with granule storage • Quick-lock system for QA/QE application unit; QA front glue storage for color change • Basic gluing unit A20; magazine height adjustment ±5 mm (manual spindle) • Extended magazine A6/A-E12/A20 for 2 coils (max Ø 830 mm); preheating station for QA/QE • Automatic pressure zone adjustment • Trimming and milling • Trimming unit HL84 with standing trimming stop for sensitive edges • Pneumatic trimming motor adjustment (2 positions: flush/level and with overhang for contour milling) • Pneumatic chamfer/straight changeover; manual side trimming stop adjustment when edge thickness changes • Rough milling unit: 2 motors stacked, each 1.5 kW, 200 Hz, 12,000 rpm; height adjustment via top pressure • Pneumatic 2-position setting: roughing with ~0.2 mm overhang / without overhang • Reserved free space for a fine milling unit • Contour milling unit Servo FK13 automatic: • 2 motors each 0.4 kW, 200 Hz, 12,000 rpm • Servo-controlled movements; automatic 8-fold tool changer • Feed speed max 20 m/min; minimum spacing between workpieces 500 mm • Workpiece thickness 12–60 mm • Automatic FK adjustment for identical radii on different edge thicknesses; auto retract • FK workpiece guidance with additional clamping for min part length 120 mm (single-sided) • Finishing and cleaning • Multi cleaning unit MN21 automatic: • Up to 3 profiles; tracing from top/bottom/side for chamfer and rounding on pre-milled PVC edges • Electropneumatic air nozzles; automatic chamfer/radius changeover; auto retract of upper/lower tool • Height adjustment via top pressure • PVC shavings separator top/bottom

Condition: good (used), Code: 0367 Brand: SCM Model: BASIC 1 Automatic edge bander for wood edges, Pvc, melamine, Abs Technical data: Working height mm 8 - 40 Hfsdpsytfnfofx Ahvsd Banding material thickness mm 0.4 - 3 Feed speed 8 mt/min Min. panel length mm 140 Min. panel width mm 60 End cutting unit : Rotation speed rpm 10000 - Motor power Kw 0,6 End trimming unit: Rotation speed rpm 27000 - Motor power Kw 0.5 - Tilt of cutters 12 degrees Working pressure Atm 6 Overall dimensions: mm 1700 x 700 x 1250 h Weight kg 470

Condition: used, Year of construction: 2007, Used Automatic Edgebander for sale! Manufacturer: SCM Hfodpfx Ahoya Tv Revsd Model: K1000 Year of manufacture: 2007 Status: dismantled and ready for transportation immediately! Location: Lithuania Equipment and technical specifications Edgeband thickness max 8 mm Panel thickness max 50 mm Thickness of coiled edgeband max 3 mm Workpiece length min 65 mm Feedrate max 18 m/min

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, DETAILED PHOTOS AND VIDEO AVAILABLE ON DISK, PLEASE CONTACT ME BY SMS AND I WILL SEND THEM. PLEASE DO NOT WRITE VIA OLX, CONTACT BY PHONE OR EMAIL ONLY. TECHNICAL DATA: Manufacturer: BRANDT Model: KDF 650 Year of manufacture: 2011 Condition: used, in very good condition Edge thickness: 0.4–3 mm Minimum workpiece width: 70 mm Minimum workpiece length: 140 mm Maximum edge width: 60 mm Maximum power consumption: 21 kW Machine dimensions: height 2300 mm, depth 1550 mm, length 5800 mm Hfodpoxuu N Hefx Ahvsd Weight: 2600 kg Connection: [230V/400V] EQUIPMENT: - Electrically controlled infeed fence - Rarely found automatic edge feeder - Pre-milling unit - Glue application unit - Pressure unit - End trimming unit (straight or angled cut) - Top & bottom trimming unit - Corner rounding unit - Radius scraper - Flat scraper - Buffing unit - 3 spray units for anti-adhesive fluids TECHNICAL CONDITION: - Machine is fully operational and in continuous production - Regularly serviced by authorized service center - Ready for immediate operation - Low operating hours LOCATION: Bochnia TRANSPORTATION: collection by the buyer

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, Single-sided edge bander with PUR, EVA, and AirFusion glue Minimum panel height: 8 mm Maximum panel height: 60 mm Minimum edge thickness: 0.3 mm Maximum edge thickness: 22 mm Hedpfx Asyuurvshvofd Panel support guides Panel infeed alignment system Pre-milling unit Gluing system End trimming unit Rough trimming unit (top and bottom) Fine trimming and rounding unit Corner rounding unit Edge scraper unit Brushing unit

Condition: ready for operation (used), Year of construction: 1992, functionality: fully functional, type of input current: three-phase, plate height: 50 mm, From business closure Type: IMA Compact 309 C Year of manufacture: 1992 For roll material and strips up to 9mm thickness Hedjx Avcdepfx Ahvjfd - Gluing with hot-melt adhesive granulate - End trimming - Sawing - Flush milling - Scraper knives and buffing Payment in cash upon collection. Private sale – no warranty.

Condition: good (used), Year of construction: 1998, 0.4-5 mm Workingpiece thickness from to 10-50 mm Hedpfsx Tu Rdex Ahvsfd Total length 2730 mm Weight 720 kg

Condition: ready for operation (used), Year of construction: 2007, General Data Measurements depth 7755 mm This HOMAG Optimat KAL 310 was manufactured in 2007. It features a left-hand version edgebander with a maximum workpiece thickness of 60 mm and a feed speed of up to 24 m/min. Equipped with a PU edge gluing system and PowerControl PC 22 unit, it spans 7755 mm in length and handles edge thickness up to 3 mm. Consider the opportunity to buy this HOMAG Optimat KAL 310 edgebander. Contact us for more information. Application Types Hjdpfx Ahjx D Nqwovofd Edge Banding

Condition: ready for operation (used), Year of construction: 2005, General Data Machine weight 2600 kg Measurements height 2300 mm Dimensions Hfsdpex E Eggefx Ahvod Machine Length 6060 mm This BRANDT OPTIMAT KDF 670 edgebander was manufactured in 2005. It features a comprehensive range of processing units including pre-milling, glue application, edge feeding and cutting, and polishing. Capable of handling workpiece thicknesses from 8 to 60 mm and edge bands up to 15 mm. Feed speed reaches up to 20 m/min, optimizing productivity. Consider the opportunity to buy this BRANDT OPTIMAT KDF 670 edgebander. Contact us for more information about this machine. Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2021, Additional Equipment Mobile Console with integrated PC"eye-M": 21.5" LCD color display through a 16/9 sized touch screen / AAR Anti-Adhesive Device: Positioned before panel edge trimming unit / Spray-Mist Device: Positioned for edge finishing and glue cooling / Loader for Narrow Pieces: Device to facilitate manual square loading of narrow pieces Hodpfx Aox D Rcbjhvofd This SCM STEFANI MD edgebander was manufactured in 2021. It features a versatile automatic edge banding capability for solid wood up to 15 mm, with an option for 22 mm. The machine includes an "SGP" glue pot for both EVA and PUR glues, ensuring a perfect joint line. The "Startouch" control system offers a 12” touch-screen display, customizable working programs, and graphic simulation of machining. Ideal for high productivity with speeds up to 25 m/min. Contact us for more information. Application Types Edge Banding

Condition: ready for operation (used), Year of construction: 2024, Additional Equipment Application unit with Teflon coating for 1.5 kg EVA granulate Upper and lower polishing unit This FORMAT4 TEMPORA 60.06 glueBox x-motion edgebander was manufactured in 2024. It features a turntable magazine with a diameter of 750 mm for edging material ranging from 0.4-3 mm, a GlueBox application unit, and upper and lower polishing units. The machine includes advanced x-motion Plus control with a 15' SmartTouch screen and a multifunctional milling unit for precise plastic edge machining. Contact us for more information about this machine. Hsdpfxsx D Hbtj Ahvsfd Application Types Edge Banding