Used Bale presses for sale (210)

Condition: good (used), Year of construction: 2019, operating hours: 2,320 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 720 mm, bale height: 1,100 mm, overall weight: 12,500 kg, oil tank capacity: 800 l, power: 37 kW (50.31 HP), Technical data baler: Manufacturer Riko Ekos d.o.o Type S-60K (6) Year of construction 2019 Operating hours 2,320 hours, as of August 24 Number of pressed bales 4,359 bales, as of August 24 Pressing force main press 60 tonnes Dimensions of feed chute 1,100 x 1,400 mm Filling volume / pressing cycle 2.1 m³ Bale dimensions 720 x 1,100 mm (W x H), the length is variable Drive power 37 kW Connected load, total 47 kW Tying 4-fold horizontal, fully automatic Throughput capacity with a bulk density of 30 kg/cbm approx. 5 - 6 tonnes/hour Bulk weight of 50 kg/cbm approx. 9 - 11 tonnes/hour Bulk weight of 100 kg/cbm approx. 15 - 19 tonnes/hour Filling volume of hydraulic oil tank 800 litres PLC control Siemens SIMATIC S7-1200 Siemens SIMATIC HMI control panel Press dimensions assembled without hopper and chute 12,220 x 3,654 x 2,685 mm (L x W x H) Nwsdpfou Thipex Af Ejn Effective transport dimensions excluding press, with dismantled tying system 7,230 x 1,750 x 2,685 mm (L x W x H) Transport weight press 12.5 tonnes Condition of the baler: The machine is part of a sorting line and was only partially used for pressing individual material flows. The machine is now no longer needed and has therefore been sold. However, the baler is regularly put into operation once a week for two to three bales so that the machine remains in working order. Due to the extremely low operating hours, the baler is in good condition and ready for immediate use. Scope of delivery for the baler: 1 piece baler without conveyor belt, hopper and chute 8 pieces wire pulling stations, without wire 1 piece bale chute 1 set of machine documentation Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2019, operating hours: 1,022 h, functionality: fully functional, Baler Presto CC 20 M, year of manufacture 2019, pressing force 20 t, with retention device. Technical data: Manufacturer: Presto Model: CC 20 M Year of manufacture: 2019 Operating hours: 1022 Pressing force: 20 t Cycle time: 24 s Drive power: 7.5 kW Filling opening: 1030 x 750 mm Filling volume: 0.53 m³ Tying: 3-fold, manual Throughput capacity at bulk density of 35 kg/m³ - 1.6 t 60 kg/m³ - 2.3 t 100 kg/m³ - 2.8 t Bale dimensions: 700 x 750 mm Bale weight: up to 300 kg Dimensions: 3300 x 1235 x 1860 mm (LxWxH) Machine weight: approx. 2500 kg Materials: paper, cardboard, film Note: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find a video on our website or YouTube channel. Nwsdjxfh H Hjpfx Af Ejn Inspections, including under power, are possible at any time by appointment. Upon request, we can also conduct tests with your material for a service fee. We are happy to answer any questions about the machine by phone from Monday to Thursday, 08:00 to 14:00. On Fridays, we are available from 08:00 to 13:00. Please note: All technical data is based on information provided by the manufacturer. We accept no liability for the information given or for any potential errors. Offers are subject to change, prior sale reserved, and may be revoked at any time. Inspections are possible by appointment. The sale is ex location, without warranty or guarantee.

Condition: good (used), - Large filling opening, ideal for large boxes - Container tipper for convenient filling Pressing force in kN: 400 Bale length: 1,100 mm Nsdpfxjv Amv Ee Af Ejwn Bale width: 750 mm Bale height: 750 mm Press length: 5,640 mm Press width: 1,674 mm Press height: 2,500 mm Weight: 4,450 kg - Motor power in kW: 9 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg - Manual binding: 3 times with wire Year of manufacture: 2013 HSM HL 4010 LI baler - Large filling opening, ideal for large boxes - Container tipper for convenient filling Pressing force in kN: 400 - Motor power in kW: 9.5 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 350 kg - Manual binding: 3 times with wire Year of manufacture: 2012

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, pressing force: 50 t, Fully functional Bramidan B50 baler, serviced, complete set - hook, strap rolls. Nwodpfxoxg Tk Tj Af Eon

Condition: excellent (used), Year of construction: 2016, functionality: fully functional, pressing force: 80 t, DIXI 80 SLD horizontal press Nsdoxg Iquspfx Af Ejwn Semi-automatic press system with 80 tons of pressure for economical volume reduction of residual materials (recyclable) in industry and retail: Cardboard Tetra packs Films Foams PET bottles Insulating mats and other compressible materials. Pressure force : 80 t Electrical connection : 400 V 50 Hz; 11 kW; D-32 A (option: K-32 A) Cycle – average approx. : 35 sec Length approx. : 4,320 mm (without lifting device and pallet) Width approx. : 1,830 mm Height approx. : 2,620 mm (with hopper) Loading opening (WxD) – housing : 1,040 x 1,110 mm Bale dimensions : 1,120 x 1,120 x 1,200 mm Bale weight approx. : 500 – 600 kg Tying 4 manual, wires with quick-release eyelets Machine weight approx. 8,000 kg (without bale)

Condition: used, Year of construction: 2004, The device is in working condition. Nsdpfxow Tbfgs Af Eewn

Condition: excellent (used), operating hours: 2,658 h, functionality: fully functional, pressing force: 71 t, filling opening width: 1,000 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, input current: 200 A, oil tank capacity: 1,250 l, empty load weight: 29,000 kg, Technical data baler: Manufacturer BOA Recycling Systems B.V. Type M75-45-A-5-1.6 Ecoline Year of construction 2021 Hours of operation 2,658 hours (as of May 2024) Number of pressed bales 42,212 pieces (as of May 2024) Press power main press 71,2 kN (71 t) Specific press capacity 9 kg/cm² Operating pressure 280 bar Cylinder stroke 2,200 mm Njdsu Thcvepfx Af Eewn Feed channel 1,620 x 1,000 mm Capacity per cycle time 2,4 m³ Theoretic cycle time 21 seconds Theoretic throughput rate 450 m³/hour Bale size 1,100 x 720 mm, length variably adjustable up to 1,400 mm Driving motor 45 kW Connected load 100 kW Current consumption 200 A Tying system 5-fold vertical, fully automatic, the press stamp is prepared for an additional 3-fold horizontal binding Throughput rate at a bulk weight of 30 kg/cbm approx. 13,6 tons/hour bulk weight of 50 kg/cbm approx. 24,2 tons/hour bulk weight of 100 kg/cbm approx. 36,4 tons/hour bulk weight of 150 kg/cbm approx. 54,7 tons/hour Bale weight up to 600 kg, depends on material Volume hydraulic oil tank 1,250 l SPS controller Siemens S7 1500 Operating panel Siemens SIMATIC HMI TOUCH Transport dimensions of press 10,000 x 2,800 x 3,385 mm (l x w x h) Press height set up with feed chute 4,743 mm Press height with conveyor belt 7,123 mm Machine weight baler approx. 29 tons Noise level <85 dB (A) Condition of the baler: With 2,658 operating hours, the press is almost as good as new and in very good condition, has hardly any signs of wear and is ready for immediate use. Due to larger material input quantities, the pressing force and throughput of the machine no longer meet the customer's current requirements and is therefore being replaced by a new 120 tonne baler. Only the baler is for sale, without conveyor belt and wire drawing stations. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 2015, operating hours: 1,932 h, functionality: fully functional, Baler Presto CC 50 M, semi-automatic, year of manufacture 2015, pressing force 50 t, with lifting and tipping device Technical data: Manufacturer: Presto Model: CC 50 M Year of manufacture: 2015 Operating hours: 1932 Pressing force: 50 t Cycle time: 52 s Drive power: 7.5 kW Filling opening: 1030 x 1100 mm Filling volume: 0.85 m³ Tying: triple, wire, manual Throughput (bulk density): 35 kg/m³ – 1.3 t 60 kg/m³ – 1.7 t 100 kg/m³ – 2.2 t Bale dimensions: 750 x 1100 mm Bale weight: 300 kg Dimensions: 4705 x 1680 x 2540 mm (LxWxH) Machine weight: approx. 4000 kg Nwjdpjxfh Htsfx Af Ejn Materials: paper, cardboard, film The operating manual is available in German. Note: The machine is in good condition. It has been inspected and tested at our facility in 28816 Stuhr. You can find a video on our website or on our YouTube channel. Inspections, including under power, are possible at any time by appointment. We also offer test runs with your material for a handling fee upon request. We are happy to answer any questions about the machine by phone from Monday to Thursday between 08:00 and 14:00, and Friday from 08:00 to 13:00. Please note: All technical data are based on information provided by the manufacturer. We do not accept liability for any information given or for possible errors. This offer is subject to confirmation, prior sale, and may be revoked at any time. Inspections are possible by appointment. The sale is ex works against prepayment, without warranty or guarantee.

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Nodpfx Afjtvau As Eswn Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: good (used), Manufacturer: Comp Tip: SB5 Engine: 2,2 KW Nedpjh Eic Ajfx Af Eewn Cylinder stroke length: 500 mm Chamber size: 500 x 350 x 400 mm

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping Njdpsvq Rtksfx Af Eewn - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Year of construction: 2008, power: 4 kW (5.44 HP), The Strautmann PP 1207 Baler Potential recyclable materials: Cardboard, film, PET bottles, foam, cans, electronic scrap Technical specifications: Manufacturer: Strautmann Model: PP 1207 Bale size (L x W x H): 1200 x 700 x 800 mm Bale weight: approx. 400 – 500 kg External dimensions (L x W x H): 1844 x 1067 x 2868 mm Transport height: 1970 mm Feed opening: 1145 x 430 mm Pressing force: 580 kN Throughput rate: 1 – 2 bales per hour Number of strapping channels: 4 Machine weight: 2,200 kg Power supply: 400 V / 50 Hz Power requirement: 4 kW Installation site: indoors / outdoors (covered) Noise level: below 80 dB(A) Year of manufacture: 2004 Baler rental possible (Lithuania, Latvia, Estonia, and Poland) Nsdpfxexftvys Af Eown PRICE ON REQUEST!

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Nwedpfevf E Avox Af Een Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: good (used), Year of construction: 2016, operating hours: 2,074 h, functionality: fully functional, Vertical baler HSM V-Press 1160 plus, year of manufacture 2016 Technical data: Manufacturer: HSM Model: V-Press 1160 plus Year of manufacture: 2016 Operating hours: 2,074 Pressing force: 55 t Drive power: 4 kW Cycle time (idle): 25 s Filling height: 1,115 mm Filling opening: 1,195 x 650 mm Bale size: 1,200 x 1,100 x max. 1,200 mm Bale weight: 550 kg Dimensions: 1,700 x 1,800 x 2,200 mm (W x D x H) Weight: 2,430 kg Materials: Paper, cardboard, cartons, films, plastics, PET The operating manual and EC declaration of conformity are available in German. Remarks: The machine is in very good condition. It has been inspected and tested at our site in 28816 Stuhr. The video can be found on our website or YouTube channel. Inspections, including under power, can be arranged at any time by appointment. Upon request, we also carry out tests with your material for a handling fee. If you have questions about the machine, we are happy to assist you by phone from Monday to Thursday, 08:00–14:00. On Fridays, we are available from 08:00–13:00. Nsdpfx Afjxfh Dlj Eswn Please note: All technical data refer to the manufacturer's specifications. We accept no liability for the information provided or for any errors. Offers are non-binding, subject to prior sale, and can be revoked at any time. Inspections are possible by arrangement. The sale is ex location, without warranty or guarantee.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Nwjdpfx Afjtvat Te Esn After refurbishment, this baler is sold with a 2-year warranty.

Condition: good (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 5536, pressing force: 50 t, filling opening width: 1,252 mm, filling opening length: 1,100 mm, bale length: 1,200 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 500 kg, total width: 3,000 mm, total height: 3,000 mm, total length: 9,500 mm, feed length X-axis: 1,200 mm, feed length Y-axis: 1,200 mm, feed length Z-axis: 1,200 mm, type of input current: three-phase, input voltage: 400 V, input current: 100 A, overall weight: 16,000 kg, noise level: 80 dB, pressure: 250 bar, pressure (max.): 250 bar, opening width: 1,100 mm, control cabinet height: 1,700 mm, control cabinet width: 700 mm, control cabinet length: 900 mm, oil tank capacity: 600 l, power: 45 kW (61.18 HP), empty load weight: 16,000 kg, volume flow: 16,000 m³/h, operating pressure: 200 bar, transport width: 3,000 mm, protection type (IP code): IP55, Equipment: compressor, documentation/manual, Presona LP50VH3, and as a bonus, you also get the Presona PP1500-500. The PP1500-500 is actually an auxiliary device used for specific tasks, such as precise cutting or additional processing of material, which the base machine itself does not handle. So the PP1500-500 is there to allow you to perform additional specialized operations that the main machine cannot do. Njdpfx Afjxfr Alj Ejwn

Condition: used, Year of construction: 1991, power: 3 kW (4.08 HP), For sale or rent! Nsdpfxoxftrns Af Eewn We are offering an HSM 155VL vertical baler for sale. Manufacturer: HSM Model: 155VL Year of manufacture: 1991 Motor power: 3.5 kW

Condition: used, Year of construction: 2009, operating hours: 20,536 h, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, empty load weight: 16,000 kg, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 20,536 hours, as of September 2024 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Njdpsu Thypjfx Af Eewn Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine is currently in our workshop undergoing partial refurbishment. We expect the refurbishment work on the machine to be completed by the end of October, after which the machine will be tested and released for sale.

Condition: reconditioned (used), Year of construction: 2008, operating hours: 23,000 h, machine/vehicle number: 00834, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,315 mm, bale width: 1,100 mm, bale height: 720 mm, warranty duration: 3 months, power: 30 kW (40.79 HP), year of last overhaul: 2025, Equipment: documentation/manual, Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler, hereby offers the following machine(s) A repaired HBC60 (30kw) Repaired – in very good technical condition Year of construction: 2008 Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Nodpfxsxck U Ue Af Eewn Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW Following repairs have been done in our official Bollegraaf OEM Refurbishment Workshop: * Safety doors needle installation replaced with new * Ram wheels behind replaced with new * Bronze strip above ram replaced with new * Movable beam position switch ram replaced with new * Scraper above ram replaced with new * Sealing pre press cylinders replaced with new * New steel beams channel cylinder * nieuwe buisjes oplassen en wielen gangbaar maken * New pusher cylinder underneath vertical tying unit * Safety hatch behind needle installation replaced with new * Several cables and asi modules replaced with new * New air filter * New oil filters

Condition: used, Year of construction: 2005, power: 7 kW (9.52 HP), FOR SALE / FOR RENT: VERTICAL BALER! (Rental available in Lithuania, Latvia, Estonia, and Poland) Technical Information: Manufacturer: HSM Nodpjxftiysfx Af Eewn Model: HSM 500 VL Pressing force: 54–540 kN Bale size: 1200 x 800 x 1200 mm Bale weight: approx. 500 kg Max. bale size: approx. 1200 x 800 x 1200 mm (W x D x H) Press chamber dimensions: 1200 x 800 x 1520 mm (W x D x H) Motor: 7.5 kW Year of manufacture: 2005 PRICE UPON REQUEST!

Condition: used, Year of construction: 2006, operating hours: 54,050 h, pressing force: 80 t, filling opening width: 1,020 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, oil tank capacity: 2,100 l, power: 94 kW (127.80 HP), empty load weight: 21,000 kg, Technical data baler: Manufacturer Paal Typ Konti 275 E Year of construction 2006 Hours of operation in total 54,050 hours Press power main press 80 tons at 300 bar Specific press capacity 9,7 kg/cm² Feed channel 1,600 x 1.020 mm (l x w) Throughput capacity under operating conditions 350 m³/hour Bale size 750 x 1,100 mm, length variable Driving motor 75 kW Connected load 94 kW Rated current 180 A Tying system 4-fold vertical, fully automatic Bale weight up to 750 kg, depends on material Volume hydraulic oil tank 2,100 l SPS controller (manuf., type) Siemens Simatic S7-300 Operating panel (manuf., type) Siemens Multi Panel Transport dimensions only baler 11,152 x 2,152 x 3,000 mm (l x w x h) Machine weight baler approx. 21 tons Condition of the baler: The press and conveyor belt are in satisfactory working condition, see photo documentation. Further technical data and dimensions for the conveyor belt are not currently available. The plant is currently still in operation and is to be replaced by a larger press plant in the coming months. Scope of delivery: Nwjdpsxcxm Eefx Af Een Bale press, bale chute, conveyor belt and machine documentation. Comments: The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Dismantling and loading is the responsibility of the buyer. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 24,967 h, functionality: fully functional, machine/vehicle number: 004283-0030, pressing force: 122 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, warranty duration: 24 months, year of last overhaul: 2026, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. Nwodpfsxcir Eox Af Een This is a baler HBC120s (90kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold with a 2-year warranty.

Condition: used, Year of construction: 2008, power: 3 kW (4.08 HP), The HSM V-Press 610 is a powerful baler designed for medium to large volumes of waste, making it ideal for commercial and industrial environments. This model combines high capacity, efficiency, and reliability, enabling effective compaction of a wide range of waste materials. Nwodpfx Aexfthvof Eon Pressing force: 120 kN Drive power: 3 kW Filling height: 655 mm Filling opening (W x H): 800 x 495 mm Bale dimensions (L x W x H): 800 x 600 x 600 mm Bale weight: 100 kg Dimensions (W x D x H): 1198 x 823 x 1986 mm Machine weight: 540 kg Model series: V-Press Consumables: Strapping tape Processable materials: Plastic film, mixed paper, cardboard, punching waste PRICE ON REQUEST!

Condition: good (used), Year of construction: 2012, operating hours: 12,078 h, functionality: fully functional, pressing force: 88 t, filling opening width: 1,100 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 750 kg, overall weight: 30,000 kg, oil tank capacity: 2,000 l, power: 98 kW (133.24 HP), volume flow: 643 m³/h, Technical data baler: Manufacturer HSM GmbH + Co. KG, Germany Type VK 8818 R-FU Year of construction 2012 Total operating hours: 12,078 hours, as of September 2025 Pump operating hours 6,616 hours (effective pump running time) Number of bales pressed: 65,792 bales, as of September 2025 Main press force 880 kN Specific pressing force 120 N/cm² Pressing force cutting edges free rammer 120 kN Dimensions of feed chute 970 x 1,800 mm Theoretical cycle time in idle mode 8.3 seconds Theoretical throughput capacity 643 m³/hour Bale dimensions 1,100 x 750 mm, the length is variable 600 up to 2000 mm Nsdpsxcngnofx Af Ejwn Drive power 2 x 45 kW frequency-controlled Connected load 98 kW Total current consumption 192 A Fuse protection 250 A slow-blow 5-fold horizontal tying, fully automatic Throughput rates with a bulk density of 20 kg/cbm 12.86 t/hour Bulk weight of 50 kg/cbm 32.15 t/hour Bale weights with a bale length of approx. 1.2 m 650 up to 750 kg/bale, depends on materiel Hydraulic oil tank capacity 2000 litres PLC control Siemens S7-300 Siemens TP 700 control panel Press dimensions assembled 18,000 x 4,300 x 3.270 mm (l x w x h) Press dimensions with conveyor system 18,000 x 22,000 x 5,765 mm (l x w x h) Transport weight baler approx 30 t (Main press approx. 20 t, press channel with bale clamp approx. 10 t) Special machine equipment: Access locking by means of key transfer system Electro-hydraulic locking of the press carriage during the tying process so that the press plunger does not change position with highly expansive materials Additional optional equipment ordered: Frequency-controlled main drive, 2 x 45 kW, with up to 40 % energy savings compared to the standard motorisation 2 x 45 kW, with the same power output Manual switch-off or switch-on of the number of strapping wires to save on strapping wire for non-expansive material Cutting-edge frei rammer with 121 kN pressing force Sensory wire monitoring, with press switch-off in the event of wire breakage or wire end Bale chute Visual warning signal, mounted on the control cabinet Condition of the baler: The entire baling system (baler and conveyor belt) is in good, operational condition. Technical data for the chain belt conveyor: Manufacturer Stadler Anlagenbau GmbH Typ chain belt conveyor KF 1800 Year of construction 2012 Drive power 7.5 kW Belt speed 0.05 – 0.4 m/second Length of feeding conveyor 6,000 mm Height of side wall from feeding conveyor 400 mm Length of incline conveyor 9,000 mm Height of side wall from incline conveyor 800 mm Length of gooseneck 1,500 mm Incline 30° Nominal width 1,800 mm Useful width 1,700 mm Belt quality EP-500/4 Steel cleats on the rubber belt 50 x 50 mm Hollow pin chain, pitch 125 mm, rollers 36 mm Height of drive axle above ground 4,284 mm Overall height of conveyor belt 5,765 mm Transport dimensions of feeding conveyor approx. 7,000 x 2,200 x 1,250 mm (l x w x h) Transport dimensions of the incline conveyor 13,000 x 2,500 x 2,900 mm (l x w x h) Pit dimensions for the conveyor belt 14,765 x 3,260 x 1,250 (l x w x h) Scope of delivery: The conveyor belt, baling press with bale chute, and wire drawing stations are available for sale, but without the wire. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: used, Year of construction: 2005, power: 7 kW (9.52 HP), SALE OR RENTAL OF VERTICAL BALER! (Rental available in Lithuania, Latvia, Estonia, Poland)! Technical information: Manufacturer: HSM Model: HSM 500 VL Press force: 54–540 kN Bale size: 1200 x 800 x 1200 mm Bale weight: approx. 500 kg Max. bale size: approx. 1200 x 800 x 1200 mm (W x D x H) Press chamber dimensions: 1200 x 800 x 1,520 mm (W x D x H) Motor: 7.5 kW Year of manufacture: 2005 PRICE ON REQUEST! Nwedpfx Aexftg Eef Eon