Bollegraaf HBC80K (45kW)

Bollegraaf HBC80 (45kW)

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 97020-0010, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, power: 45 kW (61.18 HP), operating pressure: 250 bar, Equipment: documentation/manual, This baler is sold by Bollegraaf Recycling Solutions. This is a HBC80 baler (45kW) with cross wires and a chain conveyor. Bale press built: 1997 Chain conveyor built: 2015 Gedpjxvh Dysfx Ag Dekf Baler Bollegraaf HBC80 45 kW Bale dimensions: 1100 x 720 mm 45 kW main motor Intermediate hopper Conveyor chute Control cabinet Schneider PLC Chain conveyor Horizontal floor section: 6000 mm Rise section: 12500 mm (30 degrees) Gooseneck This baler can be inspected in operation until the end of March.

Condition: refurbished (used), Year of construction: 2018, Mobile hammer mill Mobil Flex 1000 with drum magnet and discharge belt Drive: 250 Kw electric 4-hydraulic supports for lifting the machine for transportation Total weight: 33,000 kg Rotor weight: 3,000 kg Production: up to 11 to/h (depending on material size, grid size, parameter settings) Gksdpjph Uy Tjfx Ag Djf With soundproof housing Dimensions: 11,750 x 2,500 x 4,380 mm Number of hammers: 24 pcs. Hammer weight: 22 kg System is being overhauled

Condition: used, Plant: lamella separator, lamella clarifier, lamella separator Condition: used, up to 120 m³/h depending on medium Design: robust, powerful design Material: VA on conatin frame, 30 ' container, scraper plates: in PP dimensions: LXBXH 7580X2435X3000 mm Weight: approx. 8000 kg Principle: The dirty water is fed to the inlet of the lamella separator and flows downwards in it. Due to the arrangement of the lamella plates in the lamella separator, the dirty water is diverted below the lamellae and flows upwards through the lamellae. Thus, the solids sink to the bottom of the lamellas. The purified water is transported to the outlet. The solids on the lamellas gradually slide down along the lamella plates. This is where the sludge funnel is located. Scraper: Optionally, we offer the lamella separator with a scraper, which keeps the sludge flowable. Godpfoppyhtsx Ag Dekf Application: Separation of solids and liquids by sedimentation. Lamella separators are often used as a preliminary stage before filter presses or decanters for thickening. By pre-thickening a thin sludge, the filter press can be sized smaller in terms of filter area. The plant is in good condition and is available for rent or purchase. An inspection at our plant is possible by arrangement. We also offer new lamella separators with a delivery time of approx. 8 to 10 weeks !

Year of construction: 2002, condition: used, Plant: Used decanter / centrifuge mobile Manufacturer: Hiller Model: Solid bowl screw centrifuge Type: DP45-422 Decapress Machine No.: 2884 Gedpfxoppt Sfe Ag Dokf Year of construction: 2002 Maximum drum speed: 3800 I/min Inner diameter of bowl: approx. 450 mm Drum material: HII/St52 Electric motor: 30 kW Total mass: approx. 3650 kg Purchase and rent possible.

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Bale dimensions 1,100 x 720 mm, variable length Gsdsu Thhrspfx Ag Dskf Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: new, Bunker conveyor suitable for the feeding of presses, shredding, etc.. Delivery throughout Europe possible. Technical data: POS. 1 feed hopper POS. Task 2, vol. 1, 5kW, conveyor width: 1100 mm, axis dimensions: 3500 mm POS. Platform 3, volume 1, 1kW, conveyor width: 1100 mm, axle size: 4700 mm Standard discharge height: 2800 mm (greater than possible with distance feet as shown on the illustration) Gsdpfx Ajdxwlqog Dokf Ordering goods Further information and data upon request

Condition: new, Year of construction: 2025, functionality: fully functional, total width: 10,000 mm, total length: 9,000 mm, total height: 4,500 mm, Equipment: roof tent, NEW EQUIPMENT Our various sizes – please let us know which one you require: 6m Widths → 6.1m x 6.1m x 3.66m → from €2,599 → 6.1m x 9.15m x 3.66m → from €2,999 → 6.1m x 12m x 3.66m → from €4,499 → 6.1m x 18m x 3.66m → from €4,520 9m Widths (Arch Spacing 1m or 2m) → 9.15m x 10m x 4.5m → from €3,600 → 9.15m x 12m x 4.5m → from €4,149 → 9.15m x 16m x 4.5m → from €4,999 → 9.15m x 20m x 4.5m → from €6,799 → 9.15m x 26m x 4.5m → from €8,399 12m Widths (Arch Spacing 1.5m or 3m) → 12.2m x 12m x 6.1m → from €12,399 → 12.2m x 21m x 6.1m → from €17,999 15m Widths (Arch Spacing 1.5m or 3m) → 15.25m x 12m x 6.1m → from €14,899 → 15.25m x 21m x 6.1m → from €22,199 ☆ FINANCING OR LEASING AVAILABLE from €69.89 per month ☆ CERTIFIED PRODUCTS ☆ TRANSPARENT OFFERS ☆ INCLUDES GERMAN STRUCTURAL ANALYSIS ☆ INSTALLATION AVAILABLE ☆ OPTIONAL FIRE OR STORM INSURANCE ☑️ Genuine 750 g/m² PVC tarpaulin → more durable than standard products on the market ☑️ Extra sturdy and tear-resistant thanks to fabric reinforcement ☑️ High UV resistance ☑️ 100% waterproof ☑️ Extra strong, galvanized tubing for maximum stability ☑️ Suitable for year-round use ☑️ German customer service and support during purchase and assembly ☑️ Snow load: up to 130kg/m² (arch spacing 1m) and 70kg/m² (2m) ☑️ Wind load: up to wind zone 4 (1m) and up to wind zone 2 (2m) ☑️ Includes ground anchors, concrete anchors and all other small parts ☑️ Spare parts guaranteed ☑️ 5-year warranty on properly installed PVC tarpaulin ☑️ 10-year warranty against corrosion of steel frame ► Most models available for immediate delivery ► Colours: green or white ► Includes German structural analysis ► Gates at both gable ends ☏ Call us! We are happy to provide you with a non-binding offer with best price guarantee. THE IDEAL ALTERNATIVE TO TRADITIONAL CONSTRUCTIONS Optimal protection against wind, sun, rain, hail, and snow! ☑️ Mostly permit-free (unlike wooden, steel or sheet metal buildings) ☑️ No foundations required ☑️ High stability and safety (certified by German engineering office) ☑️ Decades of use: high quality, warranty, and spare part availability ☑️ Robust, corrosion-free framework ☑️ Various shapes, colours, and sizes VERSATILE APPLICATIONS ☑️ For agriculture, forestry, industry, commercial, and private use ☑️ Storage space for goods, materials, or machinery ☑️ Garage / carport for trucks, motorhomes, boats or yachts ☑️ Workshop within the lightweight hall ☑️ Construction site roofing ☑️ Shelter or stable for livestock ☑️ Barn for straw, hay, and wood ☑️ Greenhouse for plants ! Prices include structural analysis ! Delivery and installation available Gkodpfsudwfnox Ag Djf *Images similar • Prices & colours may vary • All prices subject to change • Please request a non-binding quote for an exact price • Available while stocks last • Non-binding offer

Year of construction: 2024, operating hours: 10 h, condition: like new (used), Extrusion Line with Densifier – Ideal for Recycling Applications This robust and versatile extrusion line is perfectly suited for recycling polyolefins such as LDPE, HDPE, and PP. Thanks to the integrated densifier, even materials with low bulk density – such as regrind, EPS, film scraps, and other lightweight plastic waste – can be processed efficiently. The densifier compacts the loose material and feeds it directly into the extruder, ensuring a consistent material flow and stable extrusion process even with challenging input materials. Gkjdstziudjpfx Ag Dsf Key Features: • Suitable for all types of polyolefins • Ideal for lightweight, bulky materials like EPS or film regrind • Efficient feeding system via integrated densifier • Compact design and easy maintenance This line is an excellent choice for recyclers, plastic processors, and compounders who require flexibility and reliable performance when working with diverse input materials.

Condition: excellent (used), Year of construction: 1989, Pinheiro SFM1-900 Gjdjtwrqbepfx Ag Djkf - Wheel diameter 900 mm - Motor 11 kW - Height of the feeding wheel 24 cm - Belt length from 620 to 645 cm

Year of construction: 2025, condition: new, The LITech hammer mills HM 120/200/300/400 are ideal for the pre-shredding of medium-hard, hard-tough & brittle materials such as floors, precious metals, electronic scrap, epoxy resin, gypsum, glass, catalysts, ceramics, clinker, coal, coke, minerals and much more many more!! Gsdpfjg Ay Dhjx Ag Dekf