Bollegraaf HBC120s (90kW) crosswires

Bollegraaf HBC120S (90kW) + crosswires

Condition: reconditioned (used), Year of construction: 2012, operating hours: 25,895 h, functionality: fully functional, pressing force: 78 t, filling opening width: 1,100 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 24,000 kg, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), volume flow: 930 m³/h, Technical data baler: Kdjdpfx Aovwlqqoh Neg Manufacturer Presona AB Typ LP 80 VHK 1 Year of construction 2012 Total machine operating hours 25,895 hours, as of July 2025 Pump operating hours, effective 14,135 hours, as of July 2025 Number of bales pressed 235,597 pieces, as of July 2025 Press power main press 78,5 tons Specific press capacity 95 N/cm² Press power of pre-press 28 tons Volume of pressing chamber 2,7 m³ Feed channel1,500 x 1,100 mm Theoretic throughput rate 930 m³/h Throughput rate under operating conditions 410 m³/h Bale size 750 x 1,100 mm Driving motor 55 kW Tying system 5 fold vertical, 3-fold horizontal, full automatic Throughput rate with a bulk density of 30 kg/m³ approx. 9 to 12 tonnes/hour, depending on material 50 kg/m³ approx. 14 to 17 tonnes/hour, depending on material 100 kg/m³ approx. 16 to 25 tonnes/hour, depending on material Throughput capacity with MSW (Municipal Solid Waste) approx. 20 to 27 tonnes/hour, depending on material Bale weight 450 up to 600 kg, depends on material and bale length Volume hydraulic oil tank 1,000 l Baler dimensions built up with hopper 10,985 x 3,750 x 4,310 mm (l x w x h) Transport dimensions only baler 10,985 x 2,300 x 2,900 mm (L x w x h) Machine weight baler approx. 24 tons Condition of the press: The machine was partially overhauled and serviced in our workshop and, once the work was complete, tested in manual and automatic mode during operation. The following overhaul work was carried out: Machine cleaned, partially derusted and partially repainted Hydraulic oil tank emptied and cleaned Oil filter and air filter replaced, new hydraulic oil filled Press ram dismantled and cleaned All four rollers removed from the press ram and replaced Wire station with deflection rollers for the lower wire cleaned and made operational Side guides removed from the press ram, smoothed, mounted and readjusted Main hydraulic cylinder dismantled and disassembled for inspection Piston rod replaced, cylinder tube honed Complete seal set replaced, pressure test carried out Vertical and horizontal needle system for binding dismantled, cleaned, wire deflection rollers made functional and serviced Chain cleaned, greased, chain tension readjusted Drillomat cleaned, wire knife, drill shafts and drill fingers checked, retightened with torque and serviced Door contact switch checked and partially replaced. Emergency stop switch checked. Complete electrical wiring checked and partially replaced. Bearings of the wire guide rollers under the press replaced. New safety grilles for vertical and horizontal binding manufactured and installed. Machine checked, general maintenance work carried out and press tested in manual and automatic mode Scope of delivery: Only the baler will be sold. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2005, Coupling containers, 30–32 m³, suitable for screw compactors, available for right or left configuration. Used, fully functional coupling containers from €4,000, depending on condition, excluding VAT. Delivery possible. Kdsdpfx Ahegypd He Neg

Condition: excellent (used), Year of construction: 2007, operating hours: 21,676 h, functionality: fully functional, pressing force: 78 t, filling opening width: 750 mm, filling opening length: 1,500 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 25,000 kg, transport height: 3,000 mm, oil tank capacity: 1,000 l, power: 55 kW (74.78 HP), empty load weight: 25,000 kg, volume flow: 930 m³/h, operating pressure: 250 bar, How do you do? We are pleased to offer you a used baler of the manufacturer Presona AB, type LP 80 VH1. The following technical data was taken from the manufacturer's operating instructions and brochures, for which we cannot accept any liability for correctness and completeness. Manufacturer Presona AB, Sweden Type LP 80 VH1 Year of manufacture 2007 Total operating hours, 21,676 hours, as of November 2024 Main press force 78 t Specific pressing force 95 N/cm² Pressing force of prepress flap 28 t Dimensions of feed chute 1,500 x 1,100 mm Filling volume / pressing cycle 2.7 m³ Throughput capacity under operating conditions 410 m³/hour Kodpfevgrh Ujx Ah Nedg Bale dimensions 1,100 x 750 mm Drive power 55 kW Tying 5-fold vertical Hydraulic oil tank volume 1,000 L Baler dimensions assembled with hopper 10,985 x 3,750 x 4,310 mm (L x W x H) Machine weight press approx. 25 t Note: The machine was used by a recycling company to compact paper, cardboard and film. The press is in good condition, in operation until January 2025 and can be inspected by appointment. We would be delighted if this machine is of interest to you. Your service team Mertens & Frowein GmbH

Condition: ready for operation (used), Hsm HL 4809 LI baler - Large filling opening, ideal for big boxes - Container tipper for convenient filling Kdedpera Dddefx Ah Nsg Pressing force in kN: 480 - Voltage/frequency: 3 x 400 V / 50 Hz - Bale weight in kg (depending on material): up to 400 kg - Bale dimensions (length x width x height in mm): 1200 x 1100 x 750 - Machine dimensions (length x width x height in mm): 5648 x 1849 x 2515 Idle cycle time in seconds: 53 - Manual tying: 4 times with wire

Condition: new, Klanke Supercut roll splitter for efficient shredding of reject rolls. Features: -Automatic safety lock -Emergency stop rip cord -Siemens SPS Technical data: Blade length: 3000mm Cutting channel opening: 1200mm Motor power: 15kW Cutting force: 50to Kdedpfx Ahen I Rgps Neg Order goods Price and further information on request. We will be happy to make you a non-binding offer.

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Kodpfokcgynox Ah Nedg Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h Kdedpfx Ahevf E Avo Njg bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: refurbished (used), Year of construction: 1999, functionality: fully functional, pressing force: 71 t, filling opening width: 1,080 mm, filling opening length: 1,620 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 600 kg, total width: 3,450 mm, total height: 4,090 mm, total length: 10,020 mm, input voltage: 400 V, overall weight: 27,000 kg, noise level: 85 dB, pressure: 300 bar, transport height: 2,300 mm, power: 37 kW (50.31 HP), Fully automatic channel baler with pre-press flap available immediately. The machine includes a conveyor belt with a floor-mounted section. The baler is supplied in refurbished condition and the conveyor belt underwent a belt overhaul at the beginning of this year. The machine was taken out of production at the beginning of October and is currently stored in our facility. It can be demonstrated in operation at our location. This machine is particularly suitable for baling paper/cardboard and various types of plastics such as PET, HDPE, and big bags. Technical specifications baler: Drive: 37 kW Press force: 71 tons Bale dimensions: 1100 x 720 x 1300 mm (length adjustable) Number of wires: 4 vertical Filling hopper dimensions: 1620 x 1080 mm Bale weight: up to 600 kg (depending on material) Capacity: up to 20 tons per hour (depending on material) Transport weight: 27,000 kg Kodpfjxl Rqbox Ah Nedg Technical specifications conveyor belt: Length of horizontal section: 3,000 mm Length of inclined section: 7,424 mm Angle: 29° Filling option: at floor level

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. Kdedpfxjtvau Aj Ah Neg The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Kedpfx Astvat Teh Njdg After refurbishment, this baler is sold with a 2-year warranty.