Used Arburg 221 55 250 for sale (311)

Condition: ready for operation (used), Year of construction: 2015, clamping force: 1,600 kN, This 6-axis Arburg Allrounder 520 S 1600-290 / 290 was manufactured in 2015. It features a highly wear-resistant thermoplastic cylinder with a 30 mm diameter and a drive unit powered by a 30 kW motor. The machine is equipped with advanced control systems for both injection units and supports multi-component processing. If you are looking to get high-quality injection moulding capabilities, consider the Arburg Allrounder 520 S 1600-290 / 290 hydraulic injection moulding machine we have for sale. Contact us for further details. • Injection units and plasticizing • 1st injection unit: • Complete thermoplastic cylinder, 30 mm, highly wear-resistant • Nozzle contact force controlled, programmable • aXw Control ScrewPilot • 2nd injection unit: • 2nd injection unit 290, vertical • Complete thermoplastic cylinder, 30 mm, highly wear-resistant • Open nozzle 30 mm with nozzle tip; extended nozzle tip +20 mm; radius 15 • Heating band for open nozzle • Nozzle contact force controlled, programmable • aXw Control ScrewPilot • Standard worm gear coupling; coupling geometry: double-sided • Multi-component processing; parting line setup on short runners for 2nd injection unit • Injection closing with mold (“flying injection”) • Drive, hydraulics, and cooling • 65 l/min charging flow rate • Pressure accumulator module, 64 l storage volume (max. 230 bar); accumulator drive • Continuous oil cooling and filtration; increased cooling capacity • Machine cooling circuits controlled • Clamping system, ejector, and core pulls • Clamping plate set; central Ø 125 mm • Minimum installation height 450 mm (extended) • Ejector pressure P/Q controlled (requires T2); ejector cross • Core pulls: • Core pull 1 simultaneous movement (P/Q controlled, programmable) • Core pull 2 simultaneous movement (P/Q controlled, programmable) • Core pull 3 simultaneous movement (P/Q controlled, programmable) • Pneumatic core pull control 4 incl. pressure reducer • Electric core pull control 1 (requires VE 436/00) • Tool pneumatics/hydraulics connections • Electrical connection pneumatic NVD 1 (in tool) • Electrical connection pneumatic NVD 2 (in tool) • Electrical and hydraulic connection NVD 3 (in tool) • Electrical and hydraulic connection NVD 4 (in tool) • Blow-out device 1 with pressure reducer; connection for blow-out device 2 • Cooling water and mold circuits • Shut-off valve for cooling water (inlet); shut-off valve for cooling water (inlet 2) • Cooling water filter 100 µm (inlet) • 3 cooling water circuits to fixed mold plate; 3 cooling water circuits to moving mold plate • Basic equipment for 2nd cooling water distributor (manual) with 7 free cooling circuits • Control and electrics • Selogica direct control; technology level • Fuse protection for heating circuits (1–6 with 16 A) • 15 electrical heating circuits for mold heating • Boost function for heating circuits (hot runner) • Upper guard open, raised to safety clearance • Fault indicator with flashing light • Operator authorization with chip card (EUROMAP 65) • Interfaces and connectivity • Interface for conveyor belt (machine base) • Prepared for six-axis robot with SELOGICA interface Ledjyxdwdepfx Aiijhh • Robot interface (EUROMAP 67), 50-pin • Emergency stop interface (24-pin, 2-channel) • Basic equipment for electric axis control • Host computer interface OPC-UA • Temperature control unit interface (20 mA); temperature control cable HB-THERM • Serial printer interface USB; external USB keyboard interface

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, clamping force: 1,000 kN, GERMANY ARBURG ALLROUNDER 420 C Machine Model: ARBURG ALLROUNDER 420 C GOLDEN EDITION Tie Bar Distance: 420 × 420 mm Clamping Force: 1000 kN Injection Unit (EUROMAP): 290 Opening Force: 250 kN Maximum Opening Stroke: 500 mm Platen Opening: 750 mm Mould Mounting Platens: 570 × 570 mm Ejector Force: 40 kN Lhodpfey Awqfjx Aiish Ejector Stroke: 175 mm Material Throughput (PS): 20.5 – 24.5 kg/h Material Throughput (PA6.6): 10.5 – 12.5 kg/h Holding Pressure: 2500 / 2000 / 1530 bar Nozzle Contact Force: 60 kN Nozzle Retraction Stroke: 240 mm Machine Net Weight: 3650 kg

Condition: good (used), Year of construction: 2000, Arburg 420C 1000-350 Clamping force: 100 tons Distance between tie bars: 420 x 420 mm Mold plattens: 570 x 570 mm Screw diameter: 35 mm Lhedpfx Asrthkueiijh Injection volume: 230 cm3 Shot weight: 127 g New temperature control board ARB 777 (cost 2.750€)

Condition: excellent (used), Year of construction: 2019, operating hours: 8,250 h, clamping force: 2,000 kN, screw diameter: 50 mm, displacement volume: 392 cm³, injection pressure: 2,000 bar, total length: 4,110 mm, total width: 2,650 mm, total height: 4,810 mm, overall weight: 22,000 kg, clamping force: 2000 kN size of mould plates h x v: 1772 x 800 mm min. mould height: 400 mm max. open daylight: 900 mm opening stroke: 500 mm round table diameter: 2000 mm screw diameter: 50 mm Lsdeyv D T Tjpfx Aiijhh swept volume: 392 ccm injection pressure: 2000 bar equipment included rotary table screen text german screen text english CEE-socket 16A core pulling hydraulically 4x air valve 1x machine incl. water flow regulator machine without material hopper Anti vibration mounts interface robot EUROMAP 67 interface EUROMAP 73 interface OPC measures of machine l x w x h: 4.11m x 2.65m x 4.81m total weight: 22000KG

Condition: excellent (used), Year of construction: 2010, operating hours: 91,720 h, functionality: fully functional, Clamping force 150 kN Lhodpfx Aieyvt R Ijioh Screw diameter D45 mm Max. injection volume 318 cm³ Mounting plates 688 x 688 mm Total weight 6840 kgs

Condition: excellent (used), Year of construction: 2010, operating hours: 84,854 h, functionality: fully functional, Clamping force 320 kN Lhodpfx Aeyvt Iteiish Screw diameter D60 mm Max. injection volume 664 cm³ Mounting plates 1030 x 1030 mm Total weight 17.5 t

Condition: excellent (used), Year of construction: 2004, Arburg dryer Thermolift 100, year of manufacture 2004 Lhedox I Hlijpfx Aiieh

Condition: ready for operation (used), Year of construction: 2014, operating hours: 22,626 h, clamping force: 100 kN, screw diameter: 25 mm, Hydraulic injection moulding machine manufactured in 2014. This Arburg 470 H 1000-170 features a closing force of 100 tons and a screw diameter of 15/25 mm. It includes a selection unit and a single platen design, with a beam spacing of 470 x 470 mm. If you are looking to get high-quality injection moulding capabilities, consider the Arburg 470 H 1000-170 machine we have for sale. Contact us for further details. • Selection unit: yes • Single platen: yes • Beam spacing: 470 x 470 mm • Operating hours: 22,626 h • Electricals: • Operating voltage: 400 V, 3~, 50 Hz • Control voltages: 230 V, 50 Hz; 24 V~ • Motor/heating rated current: 80 / 58 A Lhjdpfx Aoytqlcoiieh • Total rated current: 138 A • Total connected load: 75 kW • Condition note: small servo motor problem Additional equipment • Geiger handling (optional)

Condition: excellent (used), Year of construction: 2019, Conveyor belt Arburg (76A) length 2,37m , belt width 25cm, year 2019 Lhsdpfxev Twx Es Aiioh

Condition: new, Year of construction: 2010, operating hours: 72,154 h, clamping force: 800 kN, screw diameter: 25 mm, displacement volume: 54 cm³, ARBURG Allrounder 900 T 800-150 Stock no.: 503576 Manufacturer: ARBURG Model: Allrounder 900 T 800-150 Control system: Year of manufacture: 2010 Operating hours: 72,154 h Technical Data – Clamping Unit Clamping force: 800 kN Tie bar spacing (h x v): 900 x 900 mm Min. mould height: 250 mm Max. daylight between platens: 550 mm Opening stroke: 300 mm Rotary table diameter: 900 mm Ejector stroke: 150 mm Ejector force: 46 kN Centric location, moving platen (D): 90 mm Centric location, fixed platen (D): 90 mm Lhsdpfx Aeytd Spoiijh Technical Data – Injection Unit Screw diameter: 25 mm Shot volume: 54 ccm Injection pressure: 2,500 bar Screw length: 24 l/d Screw torque: 210 N Plasticising rate: 49 g/s PS Free-flow injection rate: 80 g/s PS Dimensions & Weight Machine dimensions (LxWxH): 3.8m x 1.85m x 2.15m Total weight: 5,000 kg Equipment Display text in German 1x air valve Machine with rotary table Machine with water manifold Levelling elements BDE interface

Condition: good (used), Year of construction: 2013, operating hours: 36,163 h, functionality: fully functional, clamping force: 500 kN, screw diameter: 25 mm, displacement volume: 59 cm³, ARBURG Allrounder 375 V 500-170 Stock no.: 503615 Manufacturer: ARBURG Model: Allrounder 375 V 500-170 Control: Selogica-direct Year of manufacture: 2013 Operating hours: 36,163 h Technical Data – Clamping Unit Clamping force: 500 kN Minimum mold height: 200 mm Maximum mold height: 550 mm Maximum platen distance: 302 mm Opening stroke: 225 mm Rotary table diameter: 900 mm Ejector force: 70 kN Movable platen centering diameter: 125 mm Tool weight: 230 kg Technical Data – Injection Unit Screw diameter: 25 mm Shot volume: 59 cm³ Injection pressure: 2,500 bar Screw length: 24 l/d Screw speed: 35 rpm Screw torque: 210 Nm Number of heating zones: 5 Lodpfx Aijytdfioijhh Dimensions & Weight Machine dimensions (LxWxH): 3 m x 1.6 m x 3.48 m Total weight: 3,540 kg Equipment Display language: German Rotary table 1x hydraulic core pull Machine with water battery Machine without material hopper Levelling elements EUROMAP 67 handling interface EUROMAP 73 interface Interface for ejector plate safety

Condition: good (used), 1x Arburg 320C 500-170 with Multilift, safety fence, and discharge conveyor. Sold without Z-belt conveyor, temperature control units, and Koch vacuum loader. The machine is available at short notice by arrangement. Ljdpfx Ajyym Saoiijhh

Condition: good (used), 1x used Arburg 370U 500-170 With Multilift Lodpfjyym R Nex Aiijhh Immediately available!

Condition: good (used), Year of construction: 2002, Selling this machine, immediately available. For further details, see the pictures. Lhjdpfx Aieyym Rpjieh

Condition: used, Dear Sir or Madam, Lhjdpfx Aoyym N Ssiijh We offer for sale: Assembly line for inserting a gasket into a jerrycan cap incl. 2 feeder belts (for jerrycan caps and gaskets) Assembly unit as well as carton feeding and finished product discharge conveyors

Condition: like new (used), Year of construction: 2017, operating hours: 16,000 h, functionality: fully functional, 1,0 St. gebr. Zweikomponenten Spritzgießmaschine Hersteller: ARBURG Typ: 720A3200-800/70 Lhsdpfx Aiev S E Dgeioh Baujahr: 2017 Schließkraft: 320 Tonnen Holmabstand 720 x 720 mm Einbauhöhe min. /max.: 300 - 800 mm Öffnungsweg: 600 mm Schnecken DN 1: 50 mm Max. Hubvolumen: 392 cm³ Spritzteilgewicht in PS: 359 g Schnecke DN 2: 22 mm Max. Hubvolumen: 34 cm³ Spritzteilgewicht in PS: 31 g Steuerung: Selogica Technische Ausstattung anfordern.

Condition: ready for operation (used), Year of construction: 2016, operating hours: 9,171 h, clamping force: 1,600 kN, screw diameter: 45 mm, controller manufacturer: ARBURG, This 3s Arburg 520S-1500-400 was manufactured in 2016. It features a clamping force of 1600 kN and a screw diameter of 45 mm, making it suitable for high-temperature thermoplastics. The SELOGICA direct control system with a 15-inch touchscreen enhances usability. Consider the opportunity to buy this Arburg 520S-1500-400 hydraulic injection moulding machine. Contact us for further details. Lhjdpfx Aijyg I Iheieh • Programmable and controlled build-up of clamping force • Extended clamping program with 2 stages • Hydraulic, servo-controlled ejector on moving platen • Injection/plasticizing unit: • Screw diameter: 45 mm (without nozzle) • High wear-resistant version • Sinter-metal check ring • CrN coating on screw and check ring • Suitable for abrasive, corrosive, and high-temperature thermoplastics • Technology level 2 – servo-controlled, dual-circuit pump system: • Two regulated hydraulic pumps for precise, parallel movements • Programmable nozzle contact force and holding pressure • Continuous oil circulation with additional cooling and filtration • SELOGICA direct control system: • Touchscreen operation with process editor • 15-inch (38.1 cm) display • Multilingual interface (German, English, local language) • Heating capacity zones 1–6: 3.6 kW each (230 V / 16 A) • Cylinder heating temperature up to 450 °C • Connectivity/interfaces: • OPC UA interface (MES/host computer connection) • USB and CompactFlash interfaces for data storage • EUROMAP 67 robot interface • Prepared for ARBURG MULTILIFT robot system • Utilities: • Pneumatic supply with pressure regulator • Cooling water distribution with adjustable circuits and flow indicators • 400 V / 50 Hz, with neutral conductor • Hours: 9,171 Additional equipment • None included in the listing • Note: Machine is prepared for robot integration (EUROMAP 67 interface; prepared for ARBURG MULTILIFT), but no robot/automation is included.

Year of construction: 2007, condition: ready for operation (used), This Arburg 420A 1000-400 was manufactured in 2007. It features electromechanical main movements by servo drives, a modular plasticizing unit with adaptive temperature control, and a five-point double toggle clamping system with servo-electric adjustment. The Selogica control system enhances operational efficiency. If you are looking to get high-quality injection molding capabilities, consider the Arburg 420A 1000-400 machine we have for sale. Contact us for more information about this machine. • Drive technology: • Electromechanical main movements by servo drives: dosing, injection, mold open/close, ejector • Hydraulic movement for nozzle displacement • Thermoplastic processing • Small hydraulic unit with accumulator, 5.5 kW, 10 cm³ pump (Pos 132/22) • Machine platens with centering ring D125 mm (Pos 356/11) • Injection unit (servo-controlled): • Horizontal 400 injection unit Lhjdpfx Aex D Hgvoiish • Modular plasticizing unit with central coupling and adaptive temperature control • Plasticizing assembly D25 mm, high wear/corrosion resistance; open nozzle (220/25), flat nozzle tip (300/00), heater band (320/00) (Pos 060/25) • Heater band temperature up to 450 °C (Pos 427/02) • Standard drive coupling, double-flat (Pos 061/10) • Without hopper (Pos 600/06) • Servo-regulated, programmable nozzle contact force (Pos 408/03) • Clamping unit: • Five-point double toggle with servo-electric adjustment • Electric mold height adjustment • Prepared for mounting a linear robot on the fixed platen • Mold protection via ejector position monitoring (Pos 605/05) • Machine feet (Pos 605/03) • Quick coupling for ejector bar (Pos 605/06) • Electric ejector with position control (Pos 381/05) • Programmable hydraulic core for parallel movements (Pos 382/00) • Air blow unit 1 with pressure reducer (Pos 361/01) • Machine cooling circuits, regulated and programmable (Pos 525/02) • Cooling water manifold with 4 manually adjustable circuits (Pos 512/04) • Control, electrical cabinet, interfaces: • Selogica control • Software packages (Pos 555/01–555/07): Extended mechanical cycle controls; Extended movements; Production control; Optimization/Operator assistance; Quality assurance control; Documentation • Temperature-regulated electrical cabinet (Pos 605/07) • Selogica Direct, French language (Pos 131/05) • Flash card reader (Pos 455/05) • Operator authorization by card, Euromap 65 (Pos 455/06) • Acoustic alarm (Pos 457/00) • Additional socket combination with RCD (Pos 444/01) • 12 mold temperature measurement zones (Pos 469/12) • Additional heater band for nozzle (Pos 468/01) • Interface for HB-Therm mold temperature controller (Pos 453/01) • USB serial interface for printer (Pos 454/03) • Robot interface Euromap 67 (Pos 425/05) • Electrical and mechanical preparation for external robot (Pos 425/02) • Water shut-off valve (Pos 501/01) • Interface for Thermolift dryer (Pos 464/01) • Interface for color dosing unit (Pos 493/00) Additional equipment • Electric conveyor belt, programmable (Pos 412/02) • Sorting flap for separating good/bad parts (Pos 375/00)

Condition: ready for operation (used), Year of construction: 2020, clamping force: 2,200 kN, screw diameter: 70 mm, injection weight: 172 g, This Arburg 570 S 2200-800/290 was manufactured in 2020. It features a hydraulic drive system and the Selogica control system for precise operations. With a clamping force of 2,200 kN and a screw diameter of 40 mm, it is ideal for detailed injection moulding tasks. Consider the opportunity to buy this Arburg 570 S 2200-800/290 hydraulic injection moulding machine. Contact us for more information. Clamping unit • Distance between tie bars: 570 × 570 mm • Opening stroke: 650 mm • Ejector force: 70 kN • Ejector stroke: 200 mmInjection unit • Injection unit size: 290 • Injection pressure: 2,500 bar • Shot volume: 188 cm³Drive & control Lodpsx Nkp Iefx Aiijhh • Drive system: Hydraulic • Control system: ARBURG Selogica

Condition: ready for operation (used), Year of construction: 2016, operating hours: 13,361 h, clamping force: 1,600 kN, screw diameter: 45 mm, controller manufacturer: ARBURG, This 3s Arburg 520S-1500-400 was manufactured in 2016. It features a clamping force of 1600 kN, a screw diameter of 45 mm, and a servo-controlled dual-circuit pump system for precise movements. The SELOGICA direct control system with a 15-inch touchscreen enhances usability. Consider the opportunity to buy this Arburg 520S-1500-400 hydraulic injection moulding machine. Contact us for further details. • Programmable and controlled build-up of clamping force; extended clamping program with 2 stages • Hydraulic, servo-controlled ejector on moving platen • Screw diameter: 45 mm (without nozzle) • High wear-resistant version; sinter-metal check ring; CrN coating on screw and check ring • Suitable for abrasive, corrosive and high-temperature thermoplastics • Technology level 2: servo-controlled, dual-circuit pump system with two regulated hydraulic pumps for precise, parallel movements • Programmable nozzle contact force and holding pressure • Continuous oil circulation with additional cooling and filtration • SELOGICA direct control system with touchscreen process editor • 15-inch (38.1 cm) display; multilingual interface (German, English, local language) • Heating capacity zones 1–6: 3.6 kW each (230 V / 16 A) Lhedpfoyg I Egox Aiieh • Cylinder heating temperature up to 450 °C • OPC UA interface (MES/host computer connection) • USB and CompactFlash interfaces for data storage • Pneumatic supply with pressure regulator • Cooling water distribution with adjustable circuits and flow indicators • Electrical: 400 V / 50 Hz, with neutral conductor • Hours: 13,361 Additional equipment • None included as listed • Robot/automation readiness: EUROMAP 67 robot interface; prepared for ARBURG MULTILIFT robot system

Condition: ready for operation (used), Year of construction: 2014, clamping force: 1,000 kN, screw diameter: 35 mm, injection weight: 132 g, overall weight: 3,650 kg, This Arburg Allrounder 420C 1000-290 was manufactured in 2014. It features a clamping force of 1000 kN, an opening stroke of 500 mm, and a platen size of 570x570 mm. Max shot weight is 132 g. Consider the opportunity to buy this Arburg Allrounder 420C 1000-290 hydraulic injection moulding machine. Contact us for more information. • Opening stroke: 500 mm • Platen size: 570 x 570 mm Lodpfoyglrwex Aiishh • Max. volume: 144 cm³

Condition: ready for operation (used), Year of construction: 2010, screw diameter: 25 mm, This Arburg 470 S 800-170 was manufactured in 2010. A hydraulic injection moulding machine featuring a clamping force of 80 tons and tiebar spacing of 470x470 mm. It operates on 400 V 3~ 50 Hz with a total connected load of 76 kW. Consider the opportunity to buy this Arburg 470 S 800-170 hydraulic injection moulding machine. Contact us for more information. • Tiebar spacing: 470x470 Ljdpfx Aex D R Epsiiehh • Single platen: Yes • Operating voltage: 400 V 3~ 50 Hz • Control voltage: 230 V ~ 50 Hz, 24 V DC • Motor/heating rated current: 76 / 59 A • Total rated current: 135 A • Total connected load: 76 kW • Optional: Geiger Handling

Condition: ready for operation (used), Year of construction: 2007, clamping force: 5,000 kN, overall weight: 26,400 kg, This 3-axis Arburg Allrounder 920S 5000-3200 hydraulic injection moulding machine was manufactured in 2007. It features a maximum clamping force of 5,000 kN, a screw diameter range of 70 to 90 mm, and a maximum shot weight up to 1,860 g. Consider the opportunity to buy this Arburg Allrounder 920S hydraulic injection moulding machine. Contact us for more information about this machine. • Maximum mold opening force: 150 kN • Enhanced opening force: 100 / 1,000 kN • Opening stroke: up to 900 mm • Mold height: min. 400 – max. 1,050 mm • Distance between platens: 1,300 – 1,950 mm • Tie-bar spacing (H × V): 920 × 920 mm • Platen size (W × H): 1,280 × 1,280 mm • Movable platen weight (half): max. 8,000 kg • Ejector force: max. 800 kN • Ejector stroke: max. 250 mm Hydraulics / Drive • Hydraulic pump motor power: 75 kW • Dry cycle time (opening stroke 5): 4.5–6.44 s • Installed total power: 96 kW • Color: Structural light gray / mint green / red-yellow • Control cabinet safety standard: DIN EN 60204 • Socket combination: 1 × Schuko, 1 × CEE Injection Unit Lhedpfx Aieydnigoioh • Screw diameters: 70 / 80 / 90 mm • Effective screw length (L/D): 23 / 20 / 18 • Maximum shot volume: 1,232 / 1,608 / 2,036 cm³ • Maximum shot weight (PS): 1,125 / 1,469 / 1,860 g • Plasticizing capacity (PS): 185 / 215 / 250 kg/h • Maximum injection pressure: 2,500 / 2,000 / 1,580 bar • Injection rate: • Without accumulator: 290 / 380 / 482 cm³/s • With accumulator: 1,188 / 1,552 / 1,964 cm³/s • Holding pressure: max. 350 / 200 bar • Screw speed: 47 / 54 / 61 rpm • Screw torque: 3,500 Nm • Nozzle contact force: max. 110 kN • Nozzle stroke: max. 675 mm • Installed barrel heating power: 6 × 5,500 + 4,300 W • Installed nozzle heating power: 1,100 W • Oil fill volume: 590 liters • Motor + heating fuse rating: 200 A • Motor fuse: 125125 A • Heating fuse: 63 A

Condition: defective spare-parts repository (used), Year of construction: 1998, Used ARBURG 320 C 500 injection molding machine for sale. Lhjdpfsyrd D Nsx Aiish The equipment is not working, incomplete, being sold for parts!

Condition: excellent (used), Year of construction: 2013, operating hours: 19,500 h, functionality: fully functional, clamping force: 2,000 kN, screw diameter: 45 mm, Very low hours Arburg 570 E 2000-800 moulding machine fitted with Wittmann Primus 16T robot Arburg 570 E 2000-800 moulding machine specs; Hours = 19,800 Year = purchased new in December 2013 Tonnage = 200 Screw diameter = 45mm Shot weight (g PS) = 291 Wittmann Primus 16T robot specs; Lhsdjyxhaispfx Aiioh Hours = very low Year = purchased new in June 2021 Travel = Z=2000mm, Y=1000mm, X=590mm comes with integrated conveyor and cell panels