High-Speed Radial Drilling Machine

HKS MASCHINENBAU, SINGEN HKS 40

Condition: used, Radial drilling machine CSEPEL type RFh 75 / 1500 Machine no. No. 13704 Year of construction 1985 Drilling capacity in steel Ø 75 mm Drilling capacity in cast iron Ø 90 mm Spindle holder MK 5 Nominal throat depth 1500 mm Largest projection of the spindle 1500 mm (to the column) Smallest projection of the spindle 440 mm (to the column) Distance spindle nose - clamping surface 370 - 1700 mm Cantilever height adjustment 950 mm Table size / clamping surface 1800 x 1100 mm Column diameter 450 mm Pinol stroke 380 mm Spindle speed 19-1900 rpm 21 steps Feed rate 0.047-2mm/rev. 12 steps Motor power 11 kW Mains connection 380 Volt, 50 Hz, 15 kW - Clockwise/anticlockwise rotation of the drilling spindle via hand lever switch - Hydr. gear shift for spindle speed and feed speed - Hydro-mechanical central clamping - Motorized boom height adjustment - Without coolant device - Machine light - Operating instructions Giodpjlhwr Rsfx Acwer Space requirement: Length 2720 mm x width 1170 mm x height max. 3770 mm Transport height with motor on the column: 3500 mm Transport height without motor on the column: 3250 mm Weight: 6.3 tons good condition

Condition: good (used), functionality: fully functional, Characteristics: Distance between centers: 4500 mm Turning diameter: max. 750 mm Spindl bore diameter: 105 mm Control: Heidenhain Including 2 x chuck diameter 500 mm and 315 mm Including 2 x steady rest Gjdpevy Adgofx Acwoir

Condition: good (used), Year of construction: 1990, From liquidation: Mössner Rekord SSF 520 Giodeviym Djpfx Acwsr Year of construction 1990 NR.27968 Stepless speed from 15-2350m/min 4 gears Band welder BSSO25 Air pump Work light Grinding stone Table swivels left15°-right45° Table size 790x740mm Clearance vertical 390mm--horizontal 500mm-- Height of the machine 2100mm Weight approx. 700kg

Condition: excellent (used), Year of construction: 1990, MAHO MH 500W with Heidenhain TNC 320 The machine comes from a training workshop and is in very good condition. The TNC 320 offers intuitive and highly flexible operation and programming according to current industry standards. Technical specifications: - Heidenhain TNC 320 retrofit - Travel X- 500 mm, Y- 380 mm, Z- 350 mm - Spindle taper SK 40 - Vertical quill stroke 50 mm - Spindle speeds 20–3150 rpm, stepless - Feed rate 1–3000 mm/min - Rapid traverse 5 m/min - Table load capacity 250 kg Gisdpfxoxw N S Is Acwor - Total power requirement 11.3 kW - Machine weight approx. 2 t - Handheld control unit - Safety guard An on-site inspection/test under power is, of course, possible. We are happy to offer transport, installation, and commissioning at your location. Everything from a single source: We, Baumgärtner CNC GmbH, are a company specialized in: - Service - Maintenance - Overhaul - Automation of DMG machines and equipment from other renowned manufacturers. We support you throughout the entire process! From machine purchase, transport, and delivery, up to commissioning and subsequent maintenance or repair work – you can rely on us.

Condition: used, Technical details: x-travel: 700 mm y-travel: 450 mm Giodpfx Acsvc Avhswjr z-travel: 450 mm spindle cone ISO: 40 (SK 40) table surface area: 760 x 420 mm table feed: längs: 10 - 500 (Eilgang: 1,4 m/min.) mm/min table feed: vertical: 5 - 250 (Eilgang: 1,4 m/min.) mm/min spindle turning speed - continuous: 32 - 1600 / 18 step U/min spindle head swivable left - right: 10 ° links / rechts ° quill stroke vertical: 125 mm feed continuous: 10 - 500 / 8 step mm/min rapid traverse: 1,4 m/min Total power requirement: 6,5 kW weight of the machine ca.: 3,0 t dimension machine xH: 2,3 x 2,0 x 1,85 m Further features: Headstock projection min./max.: 2094 / 2544 mm Equipment: -cooling water pump with feed -Linear path measuring system - Heidenhain ND750 Accessories: -Machine vice *

Condition: good (used), Year of construction: 1997, functionality: fully functional, drilling capacity: 40 mm, quill stroke: 200 mm, quill diameter: 80 mm, Machine design - Work table 1800 x 600 mm with 4T-slots - Boom travel 1050 mm - SK 40 drilling spindle with tool clamping device - Infinitely variable speed programming - Infinitely variable quill feed via three-phase servo motor - 2 T-slots 18 mm on the machine base at the rear - 2 T-slots 18 mm on the left machine base frame - Thread cutting device - Central lubrication - Coolant device - Machine light - CE marking - Safety device - USB interface Dimensions and travels Tool holder SK 40 Column diameter mm 195 Table dimensions mm 1800 x 600 Number of T-slots 4 Distance between T-slots mm 125 Quill stroke (Z-axis) mm 200 Column stroke (W-axis) mm 410 Distance spindle bottom edge - min mm 70 Table top edge max. mm 680 Distance spindle bottom edge - min mm 970 Floor max. mm 1580 Drilling radius mm 540 - 1590 Worktable height mm 900 Cutting values Drilling capacity into solid St 60  40 GG 22  50 Thread cutting St 60 M 36 GG 22 M 42 Main spindle drive AC motor, frequency-controlled kW 5.5 at 100 % duty cycle. Speed range: min -1 15 - 2800 Torque Nm max. 250 constant from min -1 15 - 2000 Feed drives X-axis - AC - servo motor kW 0.25 Y-axis - AC - servo motor kW 0.25 Z-axis - AC - servo motor kW 4.50 W-axis - AC - servo motor kW 2.50 Rapid traverse speeds (X/Y/Z): m/min. 7.5 / 7.5 / 5 Rapid traverse speeds (W): m/min. 3 Feed rates stepless mm/min 5 - 2000 Accuracy Positioning accuracy X-, Y-axis to 1200 mm mm ± 0.075 Electrical data Operating voltage / frequency V / Hz 400 / 50 Control voltage V 24 Hydraulic unit for clamping kW 0.75 Total connected load kVA 13.0 Weight Danumeric 440 (without packaging) with table 1800 x 600 mm kg 2800 CNC control Axes: 4 (X, Y, Z, W), expandable Processor: 32-bit CPU Screen: TFT flat screen, backlit, easy to read from all sides legible from all sides, 215 x 160 mm Position information: Cartesian or polar, absolute or incremental measurements, Unit of measurement: mm or inch or in degrees Interpolation: 2 axes (X, Y) Technology database: tool management, tool suggestions according to machining type, material-dependent cutting data suggestions Tool management: max. 500 tools Subroutine technology: yes Machining cycles Gedpermkfnsfx Acwjir Standard software options: Programming in dialog, 38 zero offsets, rotation and mirroring, teach-in for X, Y, Z, restart in program with selection functions for targeted entry Zero point determination: Cycles for determining zero points by manually probing the workpiece for by manually probing the workpiece for: - any clamped rectangular parts - any clamped round parts - Mediation of cast and flame-cut parts - Angular position detection for round parts by touching reference edges or surfaces Test graphics Graphic display of drilling patterns Data interfaces USB

Condition: used, functionality: fully functional, Year of construction: 2008, Used RAS 86.33 swing-beam guillotine shear with newly ground upper and lower blades, always serviced and rarely used. Technical specifications: Year of manufacture: 2008 Weight: 6,800 kg Max. sheet thickness at 400 N/mm²: 6.3 mm Working length: 3,190 mm Stop depth: 5-1,000 mm Working height: 800 mm Stroke rate per minute: 30-64 N/min Connections: 400 V / 50 Hz / 40 A Gjdpfx Acev Tk Exowoir 3 PE / three-phase AC Power consumption: 18.5 kW Machine width: 3,830 mm Machine depth without angle stop: 2,195 mm Machine depth with angle stop: 3,275 mm Machine height: 1,725 mm Air pressure: 5 bar Frame overhang: 100 mm Tank capacity: 150 l

Year of construction: 1990, condition: excellent (used), functionality: fully functional, machine/vehicle number: SN7088302, For sale Used Demag single girder overhead crane ± 11,365 mm x 5,000 kg Giodpfx Ajv Ipr Hecwer We can optionally supply the cranes including: * adjust in length * Assembly and inspection * conductor rails * radio control Jan Reiling B.V. also supplies new cranes completely customized at very competitive prices. * overhead cranes * hanging cranes * jib cranes * KBK installations * boat lifts All our new and used cranes that we supply (within NL and BE) are supplied including warranty! In addition, we have our own stock of approx. 15,000 Demag parts. For more information, see the website of Jan Reiling B.V. keywords: Cranes, crane, roller bridge, workshop crane, warehouse crane, hoist, crane, hall crane, bridge crane, bruckenkrane, workstation crane, lagerkrane, hebezeuge, cranes, universal crane, hoist. Overhead crane, laufkrane, overhead crane. Enke

Condition: used, Year of construction: 2017, pipe diameter (max.): 80 mm, mandrel length: 4,500 mm, Mandrel bending machine S8004 ----- For the production of dimensionally accurate pipe geometries with bending radii of up to 1.5XD → maximum bending performance pipe 76 x 4 mm (400 N/mm²) → maximum bending performance pipe 60 x 60 x 3 mm (400 N/mm²) → maximum bending performance pipe 76 x 2.9 mm (stainless steel) Gjdpfjttah Rex Acwoir → total connected load 7 kW → pipe length 4.5 mtr Robust and durable steel construction in a force-locking connection - no construction susceptible to torsion due to, for example, the split construction of the bending head and mandrel carrier. Maintenance-free electromechanical drive of the bending axis. The touch display of the control enables simple and intuitive programming and use of the system. After the pipe has been pushed on, it is fixed in the carriage by the chuck. This enables the pipe to be positioned precisely and thus the creation of dimensionally accurate geometries. The standard also includes checking the pipe geometry before the bending process: If the bending process is started in the wrong position, the machine does not give permission for this. This prevents incorrect operation. Optional additional features provide more convenience and increase the output and thus the efficiency of the system. Data is exchanged from the optional pipe calculation program TBS-3D (PC version) via USB stick or via FTP access from the computer to the machine control system. USB or LAN connectors (RJ45) are available as standard. Existing pipe geometries can be converted quickly and easily, for example, using the STEP format. Standard equipment: → Electromechanical drive of the bending axis 4 kW → Speed 2.9 rpm (=17°/sec.) → Bending direction left → Bending angle resolution 0.1° → Max. bending radius 200 mm → Bending shaft diameter 50 mm → Electronic length measurement ±0.1mm → Electronic twist measurement ±0.1° → Manual stop system (overtravel stops in length) → Manual locking system (15° in twist) → Three-jaw chuck for locking the pipe in the carriage → External control panel PLC control: → Touchscreen 10.1" → ETH 10/100, X2X Link, USB → Foot switch operation → Data transfer via network (W)LAN or USB → Material database Unique graphic programming: Simple geometries can be calculated directly on the machine. The control calculates the feed values directly after entering the length and angle and the bending angles. Hydraulics: → Hydraulic power 3 kW → Hydraulic pipe clamping with adjustable clamping pressure → Programmable early mandrel retraction Options (can be ordered as additional equipment): → Variable bending speed using frequency converters or servo motors → Automatic tool retraction (manual or controlled) → Pneumatic chuck → Automatic mandrel lubrication → Pneumatic stop system (length + twist) → Mobile version (rollers) → Radius extension Pictures show new machine

Condition: excellent (used), Year of construction: 1997, pressure 170 t chamfer lenght 4080 mm distance between columns 3680 mm column arm 410 mm dayligth 385 mm stroke 215 mm ajustment speed 200 mm/sec working feed 1-10 mm/sec return speed 135 mm/sec table width 200 mm table height 1050 mm Number of working hours 25.430 h oil volume 350 l total power requirement 29 KVA Gijdoxcp Rbepfx Acwor weight of the machine ca. 16.450 kg. range L-W-H 4620 x 2210 x 2885 mm Machine in good condition Regularly serviced by the manufacturer CNC backgauge with 8 axes (!!) - in checked conditions - machinevideo - ?v=yEaRj0XJAC4 Equipment: - CNC electro-hydraulic press brake/die bending press - DELEM CNC control - swiveling front left * High-resolution graphic screen * Clear, concise menus in the operator's language * Large tool and product library * Graphic 2D programming * Automatic bend sequence calculation and collision detection * Emergency stop button at front - CNC axis adjustment: * Y1 - Y2 - X1 - X2 - R1 - R2 - Z1 - Z2 axis + CNC crowning - X axis - adjustment speed: 500 mm/sec. * Max. stop range: 860 mm - R axis - Adjustment speed: 300 mm/sec. * Max. travel: 250 mm - Z axis - Adjustment speed: 1000 mm/sec. * Max. travel: 3260 mm - CNC electric motor table crowning - CNC electro-pneumatic die shift (I axis) - WILA / TRUMPF upper tool clamping - hydraulic - WILA / TRUMPF lower tool clamping - hydraulic - 2x front, robust support arms - movable - 1x freely movable 2-hand/foot control - 1x freely movable foot switch - Side safety device (swivel doors) - Rear safety device (sliding doors) - Original operating instructions