Eccentric Press - Single Column

HELMERDING EH35B

Condition: used, Eccentric Press, C-Frame Press, Helmerding EH 35 B, Used Machine Manufacturer: Helmerding Type: EH 35 B Year of Manufacture: 1985 Weight: 2500 kg Technical Specifications: Press Capacity: 35 tons Stroke Length: 70 mm Table Dimensions: 600 x 450 mm Operating Modes: Continuous / Single stroke (Inching) Safety: Two-hand safety start control Nlodpfxsy D Uhde Amysd Dimensions: Overall Dimensions: 1020 x 1600 x 2400 mm Additional Information: Note: The base plate (bed plate) is not included with the machine.

Condition: used, Year of construction: 2007, x-travel 620 mm y-travel 420 mm z-travel 400 mm Nedpoyq Sv Defx Amyeld control TNC 320 HEIDENHAIN spindle taper ISO 40 spindle turning speed range 50 - 4.000 U/min table-size 800 x 400 mm table load 400 kg feeds -stepless- 0 - 8000 mm/min rapid traverse 8,0 m/min power capacity 6,0 kW quill stroke 80 mm voltage 400 V total power requirement 17,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,90 x 2,70 x 2,05 m - .: 90288 - Control: TNC --- - electrical hand wheel - Horizontal milling spindle - Coolant equipment

Condition: excellent (used), Year of construction: 2010, feed length X-axis: 650 mm, feed length Y-axis: 500 mm, feed length Z-axis: 475 mm, feed rate X-axis: 6,000 m/min, feed rate Y-axis: 6,000 m/min, feed rate Z-axis: 6,000 m/min, table width: 450 mm, table length: 1,530 mm, X-Axis: 650mm Y-Axis: 500mm Z-Axis: 475mm Table Length: 1530mm Table Width: 450mm Table load: 350 Spindle speeds: 55 - 4000Rpm Feed rate X-Axis:6000mm/min. Feed rate Y-Axis:6000mm/min. Feed rate Z-Axis:3000mm/min. Length: 2300mm Nodpfsxtmqtox Amyjld Width: 2550mm Height: 2200mm Weight: 2850kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2021, max. travel distances (transverse x longitudinal) 280 x 600 mm distance spindle /table 500 mm Grinding surface of table 250 x 500 mm Grinding Wheel Dimension 355 x 25 x 127 mm grinding wheel turning speeds 1.500 / 1.800 mm Nljdpfx Amoxp R D Noysd power requirement 2,2 kW In our opinion, the machine is in good used condition and can be inspected under power by appointment. Accessories, tools, and clamping devices shown are only included in the scope of delivery if noted in the additional information. Subject to changes and errors in the technical data and information, as well as subject to prior sale!

Condition: new, pressure 25 t throat 200 mm stroke 4 - 80 mm table-size 520 x 400 mm no. of strokes 160 Hub/min work capacity during endurance run 1370 Nm force 2740 Einzelhub adjustment of stroke 4 - 80 mm ram adjustment 40 mm ram surface 160 x 160 mm Njdpfx Aeb U Hwnemyold hole in the table 200 x 150 mm clamping plate 500 x 380 x 60 mm hole in the table 80 mm weight of the machine ca. 1,9 t

Condition: like new (used), Year of construction: 2019, operating hours: 100 h, functionality: fully functional, machine/vehicle number: F9B192402, feed length X-axis: 450 mm, feed length Y-axis: 350 mm, feed length Z-axis: 400 mm, spindle speed (max.): 5,000 rpm, quill travel distance: 80 mm, rapid traverse X-axis: 5 m/min, rapid traverse Y-axis: 5 m/min, rapid traverse Z-axis: 5 m/min, total height: 1,990 mm, total width: 2,030 mm, total length: 1,980 mm, table width: 270 mm, table length: 400 mm, type of input current: three-phase, rotational speed (max.): 5,000 rpm, rotational speed (min.): 10 rpm, table load: 450 kg, overall weight: 2,270 kg, input voltage: 400 V, workpiece weight (max.): 450 kg, input current: 16 A, input frequency: 50 Hz, Equipment: CE marking, documentation/manual, rotational speed infinitely variable, EMCOMAT FB-450 MC with Sinumerik 828D Contouring control with “manual Machine” Universal Milling- and Drilling-Machine with Sinumerik 828D Contouring control and hydraulic tool clamping working area X450/Y350/Z400mm 7/10kW power Spindle speeds from 10-5000 U/min feeds from 10-5000 mm/min rapid traverse up to 5000 mm/min toolmaker accuracy DIN8615 tool clamping acc. DIN 69871 SK40 including:  linear guides  ball screws  vertical milling head +/-90° swivelling with 80mm sleeve stroke  swivel device for vertical milling head  hydraulic tool clamping  coolant equipment  LED-machine lamp  automatic central lubrication  rigid angle table 800x400mm Nljdpfx Amjxapdcsyod  chip box  operating tools  dokumentation  executing with open work area protection (mode3)  controlled and manual version in one mashine  Sinumerik 828D Contouring control incl. Control unit in 3-Axis with ballsrews and servodrives, Conversational cycles entry with grapfic support: Drilling cycles for drilling, pecking, reaming and tapping on linear and circular hole patterns, Milling of rectangular and circular pockets and studs, Slot milling cycle, Face milling cycle, ... USB Interface,

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Nlsdpfx Ask S Htxomyod Good condition

Condition: used, Pressure: 200 t Length of stroke: 40-180mm Strokes by minute: 32 Up table size: 630x500mm Down table size: 900x800mm Technical characteristics: AIR CLUTCH Power: 15 HP DIMENSIONS: Nlodpfx Ame Dvi Ueysd Height: 3000 mms Width: 1000 mms Length: 2750 mms Weight: 14000kgr New electric system

Condition: excellent (used), pressure 50 t throat 245 mm stroke 14 / 90 mm ram adjustment 75 mm table height adjustment 150 mm strokes per minute 42/85 table surface area 700 x 490 mm ram surface 400 x 230 mm tool hole in ram 40 mm hole in the table 240 x 140 mm daylight, max. stroke above - ram adjustment above 360 mm total power requirement 4 kW weight of the machine ca. 3,41 t dimensions of the machine ca. 0,8 x 1,75 x 2,1 m Machine was partially overhauled in our house as follows: - disassembly, cleaning and inspection - table milled over - new paintwork of the machine - shaft crack test carried out - disassemble Ortlinghaus clutch and additional brake, clean, check, replaceseals - additional air storage tanks - new control cabinet with safety control and touchscreen display - new wiring of the machine - new Vogel central lubrication system with piping - new Herion press safety valve + maintenance unit - new Balluff cam swith Nsdetrhf Aopfx Amyeld - new 2-hand control panel - new footswitch - Current UVV test with braking time measurement - Machine safe for hand inlay work

Condition: good (used), Year of construction: 2005, travel distance X-axis: 560 mm, travel distance Y-axis: 320 mm, travel distance Z-axis: 400 mm, feed rate X-axis: 2,400 m/min, feed rate Y-axis: 2,400 m/min, feed rate Z-axis: 2,400 m/min, table width: 450 mm, table length: 950 mm, Fixed table 950 x 450 mm Feeds all direction ISO-40 and 3kW 3 Axis Digital Read Out Systsem CE-Safety  Coolant system with semi closed lower base  X-Axis: 560mm Y-Axis: 320mm Z-Axis: 400mm Table Length: 950mm Table Width: 450mm Table load: 350 Spindle speeds: 2240Rpm Feed rate X-Axis:2400mm/min. Feed rate Y-Axis:2400mm/min. Feed rate Z-Axis:2400mm/min. Stroke pinole: 0 - 95mm Length: 1800mm Nedpexdltbofx Amyeld Width: 1600mm Height: 1900mm Weight: 1700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!