Case Clamp

Gannomat Concept Easy

Condition: new, Year of construction: 2026, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Gisdpow Sgnkefx Ab Dot Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Year of construction: 2018, condition: excellent (used), functionality: fully functional, Wemhöner VARIOPRESS Vacuum Membrane Press Basic 1000 S Technical Specifications: Heating platen size (mm): 2850 x 1550 Giedpfx Aov Np H Hob Dst Electric heating platen design: Aluminum, top heating platen Total pressing force (kN): 2400 Max. chamber pressure (bar): 6 Max. operating temperature: 180 degrees Celsius Max. batch or workpiece size (mm): approx. 2460 x 1180 Thermoplastic film in roll form: Film width: approx. 1430 mm Film thickness (mm): approx. 0.25 - 1 Pressure chamber height (mm): max. up to 180 Connected loads: Installed power (kW): approx. 46 Required air pressure (bar): approx. 8

Condition: new, Technical data: Gisdpfx Abegtm U Ao Djt Working width: 1100 mm Sanding belt dimensions: 1120x2150 mm Max working height: 160 mm Calibrating steel roller with a diameter of 150 mm Rubber roller with a diameter of 150 mm Sanding pad width: 50 mm Common motor power of 2 grinding aggregates: 11 Kw Speed of sanding belts: 16/18 m / s. Feed motor power: 0.55 kW Infinitely adjustable feeding belt: 4-20 m / min Worktable motor power: 0.25 Kw Pneumatic shoe for jump / jump: YES

Condition: used, power: 18 kW (24.47 HP), fuel type: diesel, Year of construction: 2022, operating hours: 269 h, Drive: Wheel Gijdpfxjyvd Amo Ab Dot Empty weight: 1.140 kg Chassis type: articulated Rental currency: EUR Please contact KEY-TEC Sales for more information

Condition: good (used), Code: 0299 Brand: SCM Model: S 630/E - CE Standard Automatic thickness planer for carpentry workshops, custom furniture, wooden window frames, wooden carpentry, sawmills, plastics, composite materials, and various - CE Standard Technical data: Electronic table positioning Pneumatic roller pressure adjustment Drive system with 3 large-diameter motorized upper rollers - Easily interchangeable Electronic feed speed variator 4/20 mt/min Work table dimensions 630 x 1000 mm Max working width 630 mm Min/max working height 3/300 mm Min working length 260 mm N° 4 knives Motor Hp 7,5 Gijdpfoyi E T Tex Ab Det Feed motor Hp 2 Suction mouth diameter 150 mm Overall dimensions mm 1360 x 1080 x 1220 h Weight kg 1000

Year of construction: 2011, condition: ready for operation (used), A Gross Apparatebau GmbH shredder, which was used in the wood industry, is available. Feed opening X/Y: 600mm/800mm, hopper volume: 0.6m³, rotor diameter: 252mm, rotor length: 600mm, rotor speed: 90rpm, drive power: 18.5kW, number of knives: 14, screen perforation: 10mm-40mm, suction nozzle diameter: 160mm, machine dimensions X/Y/Z: approx. 1800mm/1200mm/1650mm, weight: approx. 1300kg, operating hours: 4578h. Documentation available. On-site inspection is possible. Gsdpfeu Nlkxsx Ab Djit

Condition: good (used), Year of construction: 2011, Internal flange dimensions 2340 x 1340 mm Maximum panel dimensions (20mm thickness) 2340 x 1240 mm Working chamber height 60 mm Total thrust 300 t Maximum specific working pressure 5 kg/cm2 Press cylinders No. 6 diam 140 mm stroke 250 mm Giedpfxstwba So Ab Dst Lower moving platen (closing movement from bottom to top) Opening between press platens 230 mm Side load 1400 mm Pvc roller uncoiler Double loading table

Condition: new, Year of construction: 2026, The composition of the cabinet handling systems to create a manual, semi- or fully-automatic cabinet assembly line is depending on individual production requirements. Gijdpfx Asdx R D Deb Dst Cabinet assembly lines that will make work easier, reduce set-up time and increase precision, we will explain to you in a personal conversation.

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Lamella - carcass press with rapid traverse Technical data: Lamella carcass press from our showroom; Working range: width from 150 - 2.500mm , height from 150 - 1.400mm; depth 700mm; - lamella press beam top with 6 elements, lamella press beam side with 5 elements - lamella press beam with practice-proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are 40 mm thick, coated continuous support plates - The pressing force of the pressing bars is infinitely variable electronically controlled by 2 potentiometers and adjusted via frequency converter, therefore the torque transmission is absolutely wear-free. - Pressing force for horizontal press bars min. 500 daN (kg) to infinitely variable max. 2200 daN (kg) - Pressing force for vertical press bars min. 300 daN (kg) to stepless max. 2200 daN (kg) - Including option: Rapid traverse speed for fast positioning of the press bars, controlled by automatic workpiece recognition with sensors in the press bars, press speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Jog mode for precise positioning of the two pressing beams e.g. for low pressing forces, drawers and carcasses 45 degrees. Simple operation via 6 separate pushbuttons, freely adjustable pressing time preselection with automatic opening, loading height 300 mm. Machine is in our showroom and can be delivered immediately. Giodpfsiidm Nsx Ab Det Location: ex stock 54634 Bitburg - immediately available -

Condition: new, Type SK-1000-P6 Working width 1000 mm Min.working length 500 mm Working thickness 2-150mm Polishing roller speed - Frequency control Feeding speed 3-12,5 m/min Total motor power 13.87 kW Gedpfodmi Nijx Ab Deit Disc motor 1.5 kW*1 Cross motor 1.5 kW *1 Screw roller motor 2.2 kW *2 Feeding power 2.2 kW Up and down motor 0.37kW*4 Swing motor 0.37kW *2 Working table up and down 0.55 kW Transport dimensions 3650x1850x2100mm Weight 4200 kg