Used Gannomat Concept Easy for sale (5,783)

Condition: new, Year of construction: 2026, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Crsdpow Sgnkjfx Ailod Available: at short notice

Condition: new, Year of construction: 2025, The Concept Easy is the ideal assembly support for dowel construction at the case goods production as well as at drawer production. Short introduction: • Small footprint requirement, less than 1,8 m2 • Potentiometer for stepless adjustable pressing force • Pressing force min. 300 daN (kg) • Pressing force max. 2200 daN (kg) • 3 Pressing velocities and adjustment rates 5 /10 / 25 mm/sec. (with fine positioning / creep feed) • Adjustable clamping cycle time with automatic opening Crsdpfjdx Daaex Ailod

Condition: new, Year of construction: 2026, Gannomat Concept 70 Eco Lamella – Carcase Press with Rapid Traverse Technical specifications: Lamella carcase press from our showroom; Working range: width from 150 to 2,500 mm, height from 150 to 1,400 mm, depth 700 mm; - Upper lamella pressing beam with 6 elements, side lamella pressing beam with 5 elements - Lamella pressing beams with field-proven tolerance compensation for tightly pressed carcase joints - Counter-pressure surfaces are continuous, coated support plates, 40 mm thick - The pressing force of the pressing beams is infinitely variable via two potentiometers and set electronically via frequency converter, ensuring absolutely wear-free torque transmission. - Pressing force for horizontal pressing beams: min. 500 daN (kg) up to infinitely adjustable 2,200 daN (kg) max. - Pressing force for vertical pressing beams: min. 300 daN (kg) up to infinitely adjustable 2,200 daN (kg) max. Codpjy Egz Sjfx Ailerd - Including option: Rapid traverse speed for quick positioning of the pressing beams, controlled by automatic workpiece detection with sensors in the pressing beams; pressing speed 5/10/25 mm/sec and rapid traverse speed 50 mm/sec. Sensors can be deactivated for pressing special parts. - Jog mode for precise positioning of both pressing beams, e.g., for low pressing forces, drawers, and carcases at 45 degrees. Easy operation via six separate push buttons, freely adjustable pressing time preselection with automatic opening feature, loading height 300 mm. The machine is available from our showroom and can be delivered immediately. Location: ex-stock 54634 Bitburg - available immediately -

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Laminate – Body press with rapid traverse Technical data: Laminate body press from our showroom; Working area: width from 150 – 2,500 mm, height from 150 – 1,400 mm; depth 700 mm; - Laminate press beam at the top with 6 elements, laminate press beams on the side with 5 elements - Laminate press beams with proven tolerance compensation for tight body joints - Counterpressure surfaces are 40 mm thick, coated, continuous support plates - The pressing force of the press beams is continuously adjusted electronically via 2 potentiometers and set via a frequency converter, therefore, the torque transmission is absolutely wear-free. - Pressing force for horizontal press beams min. 500 daN (kg) to continuously max. 2200 daN (kg) - Pressing force for vertical press beams min. 300 daN (kg) to continuously max. 2200 daN (kg) - Including option: Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams, pressing speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Tapping mode for precise positioning of the two press beams, e.g. for low pressing forces, drawers and bodies at 45 degrees. Simple operation via 6 separate push buttons, freely adjustable preselection of pressing time with automatic opening, loading height 300 mm The machine is in our showroom and can be delivered immediately. Location: in stock at 54634 Bitburg Crodpfx Aoiidm Neilod - immediately available -

Condition: used, Year of construction: 2024, New display machine! List price: €32,665,- complete in standard configuration with: Sturdy, torsion-resistant steel frame constructed with welded and bolted assemblies. Louvered top press beam with 6 elements; louvered side press beam with 5 elements. Louvered press beams feature the proven Ganner system tolerance compensation for tightly pressed carcass joints. Counterpressure surfaces (side pressure wall and bottom) are 38 mm thick, coated, continuous support plates. Continuous pressing surface with a height of 95 mm at the lower vertical press beam. Electromotive adjustment of both press beams via precision trapezoidal threaded spindles (with increased pitch and running accuracy) and high-performance running nuts with grease reservoir. Pressing is performed electromechanically via two separate worm gear motors (2 x 0.75 kW). The pressing force of the press beams is continuously adjustable via 2 potentiometers and controlled electronically by frequency converters, ensuring absolutely wear-free force control. Pressing force for the horizontal press beam: min. 500 daN (kg), steplessly adjustable up to max. 2200 daN (kg). Pressing force for the vertical press beam: min. 300 daN (kg), steplessly adjustable up to max. 2200 daN (kg). Pressing and adjustment speed of the press beams with fine positioning, selectable via three-position rotary switch: 5 / 10 / 25 mm/second. Very simple operation using 6 separate push buttons; 8 movement sequences selectable via control system. Freely adjustable pressing time preselection with automatic opening from 0–30 min (switchable to seconds or hours). Working height/feed height: 300 mm. Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm. Weight: approx. 1800 kg net. Dimensions (Length x Width x Height): 3.45 m x 0.95 m x 2.30 m. Electrical connection: 400V, 3Ph, 50Hz (3.2 kVA, 16A). Additional equipment: Crsdpfouf Hx Hsx Ailed Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams. Pressing speeds of 5 / 10 / 25 mm/sec and rapid traverse speed of 50 mm/sec; sensors can be deactivated for pressing special components. 1 set of machine feet (working height 500 mm). Storage location:

Condition: new, Year of construction: 2025, functionality: fully functional, Gannomat Concept 70 Eco body press Year of manufacture 2025 including the following options: - Rapid traverse speed adjustment speed up to 50 mm/sec - Machine feet (working height 500mm) The Concept Eco and Concept Primus are ideal assembly aids for dowel connections when pressing bodies together, as well as when making drawers. Brief introduction: • With tried and tested tolerance compensation (GANNOMAT system) • 2 potentiometers for continuously adjustable pressing force • Pressing force min. 300/500 daN (kg) for Concept Eco or Pressing force min. 600/800 daN (kg) for Concept Primus • Pressing force max. 2200 daN (kg) for Concept Eco or Crsdpfx Aievxgrreled Pressing force max. 3500 daN (kg) for Concept Primus • 3 pressing and adjustment speeds 5/10/25 mm/sec. (with fine positioning / creep speed) • Freely adjustable pressing time pre-selection with automatic opening • Concept Eco: Simple operation via 6 separate push buttons for 8 movement sequences • Concept Primus: Simple operation via LCD display Universal application area: • Bodies e.g. for furniture and cabinets • Mitered bodies • Bodies with protruding lids • Drawers • Pressing several bodies / drawers Advantages: • Tried and tested tolerance compensation (GANNOMAT system) • Electromechanical body press with frequency-controlled gear motors • Independent vertical and horizontal press beam • Long service life thanks to tried and tested, high-quality components • Solid and robust construction • Space-saving design • Body pressing = Simple + Fast + Efficient + Flexible + Precise + Professional • Simple thanks to simple and practical control panel • Fast thanks to press beam positioning speed of up to 50 mm/sec (option) • Efficient thanks to precise pressing of a wide variety of body sizes • Flexible thanks to adjustable parameters such as e.g. Pressing force, pressing time, travel speeds • Precise through precise angle pressing of furniture bodies and drawers • Professional production of bodies and drawers using modern body presses

Condition: new, Year of construction: 2026, The Concept Eco and Concept Primus are the ideal assembly support for dowel construction at the case goods as well as drawer production. Crsdpfxjdx R Dms Ailjd Short introduction: • With workpiece tolerance compensation (System GANNOMAT) • 2 Potentiometer for stepless adjustable pressing force • Pressing force min. 300/500 daN (kg) at Concept Eco resp. Pressing force min. 600/800 daN (kg) at Concept Primus • Pressing force max. 2200 daN (kg) at Concept Eco resp. Pressing force max. 3500 daN (kg) at Concept Primus • 3 Pressing velocities and adjustment rates 5 /10 / 25 mm/sec. (with fine positioning / creep feed) • Adjustable clamping cycle time with automatic opening • Simple operation by 6 individual push buttons for 8 motion sequences

Condition: new, Year of construction: 2026, The composition of the cabinet handling systems to create a manual, semi- or fully-automatic cabinet assembly line is depending on individual production requirements. Credpjdx R D Djfx Ailed Cabinet assembly lines that will make work easier, reduce set-up time and increase precision, we will explain to you in a personal conversation.

Condition: new, Year of construction: 2026, The Concept Eco and Concept Primus are the ideal assembly support for dowel construction at the case goods as well as drawer production. Short introduction: • With workpiece tolerance compensation (System GANNOMAT) • 2 Potentiometer for stepless adjustable pressing force • Pressing force min. 300/500 daN (kg) at Concept Eco resp. Pressing force min. 600/800 daN (kg) at Concept Primus • Pressing force max. 2200 daN (kg) at Concept Eco resp. Cjdpfxsdx R Dto Ailerd Pressing force max. 3500 daN (kg) at Concept Primus • 3 Pressing velocities and adjustment rates 5 /10 / 25 mm/sec. (with fine positioning / creep feed) • Adjustable clamping cycle time with automatic opening • Simple operation by 6 individual push buttons for 8 motion sequences

Condition: good (used), Manufacturer: Easy-Link Overall dimensions: 2400 x 700 x 2300 mm Codpfxehyw N Sj Ailsrd Box size: 700 x 760 x 500 mm Belt size: 2700 x 190 mm

Condition: new, Year of construction: 2026, GANNOMAT "PROTEC 571" (Drilling, Grooving, Milling) Base machine complete in standard configuration for drilling and grooving including: - Additional safety device via louver curtain Codpfx Aszgfwljilerd - Requirement for horizontal Lamello P-system milling - Requirement for milling diameter > Ø 16 mm, as well as for the use of multi-part milling tools Detailed technical data can be found in the data sheet for ProTec Type 0571 Processing unit with: PowerBlock with 21 spindles and 1 grooving saw - 13 vertical drilling spindles - 6 horizontal drilling spindles in Y / 2 horizontal drilling spindles in X - 1 grooving unit in Y 4th drilling axis in Y Workpiece sizes and weights - Workpiece width (X): min. 60 mm / max. 1000 mm - Workpiece thickness (Z): min. 6 mm / max. 60 mm - Workpiece length (Y): min. 250 mm in continuous mode max. 5600 mm programmable workpiece length in software - Workpiece weight: max. 75 kg 1 Milling unit Profit HSK63F with 3-way magazine for automatic tool change, motor 5.5 kW (S1), 1000-18000 rpm with frequency inverter, right and left rotation, for tool holder HSK63F with collet 462E/OZ25, milling cutter length up to 130 mm including options 1 Roller table 765 mm (Y-axis) foldable, for the front of the machine, width 500 mm 1 Roller table 765 mm (Y-axis) foldable, for the back of the machine, width 500 mm 1 Auxiliary stop 600 mm with integrated rollers for roller tables 1 TOOLS: Drill set for ProTec 1 Carbide grooving cutter  125/30 mm, grooving cutter width (SB) 4 mm, Z=12, LI, from Leitz 1 Tools for milling unit Profit HSK63F and HSK63F with 3-way magazine with collet 462E up to shank diameter 25mm, HSK and milling cutter set 1 HSK mounting set 1 Mounting device HSK63F, simplest operation with the highest level of user comfort thanks to the roller clamping system, no clamping or tightening required, mounted on a stable base or on a workbench 1 Hook wrench for HSK63F collet 462E 1 Extraction distributor Ø 160 mm / Ø 80-80-80 mm, grid 196 mm 1 Counterpressure device from above 1 LED lighting in the machine's working area 1 Tool for vertical Lamello P-system milling Machine with very good equipment including many drills and tools New machine with full warranty. The machine can be viewed and demonstrated in our showroom. A special price can be offered for our showroom machine!!!!!

Condition: like new (used), Year of construction: 2018, machine/vehicle number: 390.829, functionality: fully functional, operating hours: 6,700 h, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, workpiece length (max.): 5,600 mm, workpiece width (max.): 1,000 mm, workpiece height (max.): 60 mm, workpiece weight (max.): 75 kg, number of axes: 1, number of slots in tool magazine: 1, actuation type: electric, total height: 1,409 mm, total length: 1,484 mm, total width: 2,325 mm, table width: 1,000 mm, Equipment: CE marking, For sale due to acquisition of a new machine: our Gannomat Protec 571 CNC machining center, purchased new in 2018. The Gannomat Protec CNC machining center is a high-precision woodworking machine designed for efficient drilling, milling, and grooving operations. Engineered for versatility and accuracy, it is ideal for producing furniture components and panels. Its advanced automation and robust construction ensure repeatable results and significant time savings in production. This machining center is especially suitable for workshops aiming to optimize productivity and achieve seamless machining processes. Technical specifications: - Workpiece width X: 60 - 1000 mm - Workpiece length Y: 250 - 5600 mm Cjdpfezhrdzsx Ailsrd - Workpiece height Z: 6 - 60 mm - Workpiece weight: 75 kg - Rapid machining: 21 drilling spindles - Stable grooving unit: 8.3 mm saw blade width - Powerful milling unit: 5.5 kW (S1), with reversible rotation - Compact footprint: Less than 3.3 m² Including with the machine: - Drilling tools and 1 pc. HSK63 chuck and tool for modern joinery applications. Optional software: - Gannomat Editor office software: €1,000 (installation and activation by Gannomat for an additional fee) - DXF postprocessor for efficient operation: €1,000 (installation and activation by Gannomat for an additional fee) ATTENTION: Low operating hours. The price of the machine does not include VAT.

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, sheet thickness steel (max.): 6 mm, sheet thickness aluminum (max.): 7 mm, total width: 1,700 mm, total length: 31,000 mm, total height: 2,000 mm, input voltage: 400 V, working width: 1,250 mm, coil weight: 5,000 kg, overall weight: 8,800 kg, T20 Trapezoidal Sheet Roll Forming Line for Sale * Model: T20 Trapezoidal Sheet Roll Forming Line * Year of Manufacture: 2018 * 5-ton hydraulic decoiler included * Automatic stacker at the end of the production line The machine has seen very little use and is in excellent working condition. It has been well maintained and is fully operational. The production line is currently dismantled, making it ready for transport. Csdpfx Aijzhip Ijljrd If you need any additional information, photos, or videos of the machine in operation, feel free to contact us.

Condition: new, Year of construction: 2025, Construction staircase, suitable for use on any construction site. 2 units available in stock. Can be assembled by one person in 15 minutes. Two staircases can be mounted on top of each other. Crodszhhl Ijpfx Ailed Half-turn staircase, left + right. A complete staircase can be stored on a Euro pallet.

Condition: excellent (used), Year of construction: 2022, Manufacturer: Ganner Gannomat Type: SELEKTA 253 220 V, 1 phase, 50 Hz Year of manufacture: 2022 - used Complete in standard version with: - Fully automatic electronic control system with program selector switch COILING-GLUING-DRIVING IN Credpfx Aiezbyu Aoled - Dowel feed via electronic vibrating conveyor with potentiometer for stepless adjustment of the dowel feed rate - Automatic dowel diameter and dowel length control with Auto-DL-Select system (automatic ejection of incorrect dowel lengths +/- 5 mm into the collection container) - Closed gluing system with 6 bar glue pressure via glue nozzle for glues with a viscosity of 150 to 350 mPas - Stepless electronic glue quantity adjustment with potentiometer via time preselection by electronic control - Selector switch GLUE/WATER for flushing/cleaning the gluing system with EasyClean function button (automatic cleaning program for glue hose and glue nozzle via spray funnel and dirty water collection container) - Control lamp for glue residue level indicator in the glue container - 1 stainless steel container for 5 kg of glue and 1 stainless steel container for 5 l of water for flushing/cleaning - 4 rollers for moving the machine including 1 pistol for dowels Ø 8 mm, dowel length 25 - 40 mm Drive-in overhang 7 - 20 mm Air connection: 6 bar Price ex warehouse 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, GANNOMAT "MASTER 325" FRAME DOWEL AND MORTISE BORING MACHINE Specifically designed for staircase construction Complete in standard configuration according to price list 01/19/D, featuring: - Precision collet chuck for ER40 collets Ø 3-26 mm, incl. collets Ø 10 / 13 / 16 / 20 - Pole-switchable motor 1400/2800 rpm, 1.5 kW - Line laser with bracket - Boring unit, continuously rotatable from the front (65°-0°-65°) - Position setting via digital counter - Position adjustment for 2 levels, pneumatic (0-100 mm) - Maximum boring depth 200 mm - Precision indexing rail with 12 mm pitch with central detent and lateral adjustment 320 mm - Complete stop system consisting of: 1 center stop and 1 stop for oversized frames 1 stop rod, approx. 850 mm long (can be reversed from left to right) 2 flip stops - Mortising unit lowerable, with 2 program cams (400V, 3Ph, 50Hz, 1.5 kW) Cjdpfexdttpsx Ailord Extraction funnel, dust-tested, Ø 80 mm Double miter stop adjustable from 0°-60° Pneumatic clamping of the X-axis with on/off switch at the indexing handle Pair of auxiliary workpiece supports, swiveling (left and right) Clamp column re-positionable to the front Chassis with 4 wheels for easy machine movement 1 piece Collet extension Ø 20 mm, incl. collet for drill shank Ø 9 mm 1 piece Baluster drill bit Ø 25 mm, chrome steel, with centering tip Available: at short notice

Condition: as good as new (ex-display), Year of construction: 2026, - NEW - Manufacturer: Ganner Gannomat Type: SELEKTA 253 220 V, 1 phase, 50 Hz complete in standard version with: - Fully automatic electronic control with program selector switch COILING-GLUING-INSERTING - Dowel feed via electronic vibratory feeder with potentiometer for stepless adjustment of the dowel feed rate - Automatic dowel diameter and dowel length control with Auto-DL-Select system (automatic ejection of incorrect dowel lengths +/- 5 mm into the collection container) - Closed gluing system with 6 bar glue pressure via glue nozzle for glues with a viscosity of 150 to 350 mPas - Stepless electronic glue quantity adjustment with potentiometer via time preselection through electronic control - Selector switch GLUE/WATER for flushing/cleaning the gluing system with EasyClean function button (automatic cleaning program for Crsdpjdwi Rkjfx Ailsd glue hose and glue nozzle via spray funnel and dirty water collection container) - Control light for glue residue level indicator in the glue container - 1 stainless steel container for 5 kg of glue and 1 stainless steel container for 5 l of water for flushing/cleaning - 4 rollers for moving the machine including 1 gun for dowels Ø 8 mm, dowel length 25 - 40 mm Insertion allowance 7 - 20 mm Air connection: 6 bar Price ex warehouse 54634 Bitburg - immediately available -

Condition: new, Year of construction: 2025, CNC-controlled drilling, gluing, and dowel insertion machine Complete in standard configuration with: - Support with linear guide consisting of: 1 pc. single-spindle horizontal drilling unit, motor 0.65 kW, stroke 70 mm Tool speed selectable via operator software (3000/5000/8000 rpm) 1 pc. blow-out, gluing, and dowel insertion station for dowels Ø 8 mm, dowel length 25–50 mm - Fully automatic, electronically controlled central lubrication - X-axis NC controlled, with working length 700 mm, max. traversing speed 95 m/min - Z-axis manually adjustable via mechanical digital counter, position on support table 5–40 mm - Dowel insertion projection adjustable from 7–20 mm via mechanical digital counter, drilling depth 0–35 mm (with drill length TL 70 mm), automatically set with insertion projection - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with viscosity from 150 to 350 mPas - Glue quantity steplessly adjustable via operator software - Selector switch GLUE/WATER to flush glue system, each with: 1 stainless steel container for 7.5 kg glue and 7.5 l water - Indicator lamp for residual glue level in glue container - 1 pc. left side stop, 1 pc. right side stop (all removable) - 2 pcs. start buttons for individual operation with 1–2 workpieces - 2 pcs. pneumatic angled clamping cylinders 10° for workpiece thickness up to max. 80 mm, workpiece length (Y) min. 70 mm - 1 pc. extraction funnel, connection Ø 80 mm - 1 pc. TCT controller with: Integrated industrial PC, incl. Beckhoff TwinCAT soft PLC, operating temperature range 0–50°C, 15" capacitive touchscreen TFT industrial display, operating system: WINDOWS 10 IoT LTSC (long term support channel) - Programming via menu-guided user software, drilling distances freely programmable with ABSOLUTE, RELATIVE, or GRID dimensioning, automatic workpiece mirroring and process optimization, 2 working fields assignable with different programs, graphical workpiece display, parametric programming, zero-point shift, programmable work lists, plain text error diagnosis - Integrated options: - Electronic optical glue monitoring system G.I.C. (Glue Insert Control) for 1 pc. glue nozzle, art. no. 0470-0810 - 1 EASY CLEAN system, for automatic test glue shots before starting the drilling/gluing/dowel insertion program. Cjdow Sgm Hjpfx Ailsrd E.C.S. for 1 pc. glue nozzle, art. no. 0471-Z010 - 1 single-spindle vertical drilling unit from ABOVE, 0.65 kW, (3000/5000/8000 rpm), position (Y) manually adjusted via mechanical digital counter Adjustable from 5–40 mm, drilling depth (Z) max. 30 mm (with drill length TL 57 mm) Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (incl. drilling depth compensation, e.g., for Häfele Minifix) Art. No. 0471-0830 - 4 vertical angled clamping cylinders 10° with mount, additional, Art. no. 0470-0850 Available: short notice

Condition: like new (used), Year of construction: 2025, GANNOMAT "JUNIOR 323" FRAME DOWEL AND SLOT MORTISING MACHINE Complete in standard configuration as per price list 01/22/D with: - Precision collet chuck for ER 40 collets Ø 3–26 mm, including collets Ø 10 / 13 / 16 / 20 - Motor 1.5 kW, 2800 rpm - Positioning via digital counter - Pneumatic 2-level positioning adjustment (0–100 mm) - Max. drilling depth: 150 mm - Precision indexing rail with 12 mm pitch, featuring: - Center detent and lateral adjustment 320 mm - 2 pneumatic safety clamping cylinders - Complete fence system consisting of: • 1 center stop and 1 stop for oversized frames Codpfxexdttij Ailord • 1 round stop bar approx. 850 mm long (can be mirrored from left to right) • 2 flip stops - Tiltable slot mortising device with 2 program cams (400V, 3Ph, 50Hz, 1.5kW) - Extraction hood Ø 80 mm, dust-tested - Central mitre stop 45° - Pair of auxiliary workpiece supports, pivotable (left and right) - Drill head holder - 3-spindle drilling head, 32 mm pitch (can be rotated 90°) - Chassis with 4 wheels for easy machine movement Availability: Short-term – immediately –

Condition: excellent (used), - Multifunction machine: PASTEURIZES - COOKS - COOLS Cjdpfx Ajwxu R Isilerd - MIXES - EMULSIFIES - Model: R400 A SH - Dimensions (LxWxH): 600x750x1335 mm - Tank capacity: 40 litres - Maximum water pressure: 0.6 MPa - Refrigerant: R404A - Voltage: 400V / 3PH / 50Hz - Power: 5300 W - Year of manufacture: 2015 -Iiedcuewxu R Is T Rxiei - Electronic controls - Semi-hermetic compressor - Air-cooled condenser - Refurbished machine: The machine is prepared upon order; delivery and return times are agreed at that moment (please request price after refurbishment).

Condition: excellent (used), -Multifunctional machine: -PASTEURIZES - COOKS - MIXES - EMULSIFIES - Model: R400 A SH - Dimensions (LxWxH): 600x750x1335 mm - Tank capacity: 40 litres - Maximum water pressure: 0.6 MPa - Refrigerant gas: R404A - Voltage: 400V / 3PH / 50Hz Credowxu Rzopfx Ailed - Serial number: 179342 - Year of manufacture: 2015 - Electronic controls - Semi-hermetic compressor - Air-cooled condenser - Refurbished equipment: The equipment is prepared when ordered; collection and return deadlines are agreed at the time (please request the price after refurbishment). The listing was translated automatically. Translation errors are possible

Condition: used, Year of construction: 2003, functionality: fully functional, total width: 2,670 mm, total length: 5,000 mm, type of input current: three-phase, overall weight: 2,750 kg, workpiece height (max.): 50 mm, Gannomat Matrix 250/70 We offer this used, CNC-controlled multi-spindle boring, gluing, and dowel inserting machine, manufactured in 2003. Manufacturer: Gannomat Model: Matrix 250/70 Year of manufacture: 2003 - Suitable for flat surfaces up to a diameter of 35 mm - Suitable for end surfaces: drilling 6, 8, 10, 12 mm, gluing and inserting with a diameter of 8 mm, - Dowel length from 25 to 60 mm - X-length: 2,500 mm - Y-length: 700 mm - Maximum workpiece thickness: 50 mm - Includes miter stop - A 4-zone layout is possible with a center stop Crodpfx Aijzcf Udsled - Includes 16 suction cups and 8 clamps, as shown in the pictures - Includes vacuum pump - Simple programming directly on the machine, drilling of left and right parts is easily possible without the need for extra programming; during operation, it only needs to be positioned against the respective stop The machine is currently still in use. However, we only use it as a pure drilling machine and do not use the dowel inserting and gluing functions. An inspection can be arranged upon request. If you have any questions or require more information, please feel free to send us a message.

Condition: used, Year of construction: 2017, Number of drilling spindles: 21 units Pitch: 32 mm Drill chuck: Clamping surface, drill shank: 10 mm Operation: Foot pedal Tools: Yes, in mm Drilling direction: from below and from the front Swiveling: Manually Swiveling angle: only 0° or 90° Max. pass-through height: 80 mm Max. pass-through width: 750 mm Number of material clamps: 3 units Type of material clamping: pneumatic Design: Stationary Stop system: only for this series Weight approx.: 400 kg Motor power: 1.5 kW Dust extraction diameter: 120 mm Location: Customer Crjdpfx Aisihghrelsd

Condition: used, Year of construction: 2023, New demonstration machine! List price: €86,567 net Base machine complete in standard configuration for drilling and grooving: For detailed technical data, please refer to the ProTec Type 0571 data sheet. Processing unit with: PowerBlock with 21 spindles and 1 grooving saw - 13 vertical drilling spindles - 6 horizontal drilling spindles in Y - 2 horizontal drilling spindles in X - 1 grooving unit in Y 4th drilling axis in Y Workpiece sizes and weights - Workpiece width (X): min. 60 mm / max. 1000 mm - Workpiece thickness (Z): min. 6 mm / max. 60 mm - Workpiece length (Y): min. 250 mm in through-feed modemax. 5600 mm programmable workpiece length in software - Workpiece weight: max. 75 kg Milling unit Profit HSK63F with 3-position magazine for automatic tool change, motor 5.5 kW (S1), 1000–20,000 rpm with frequency converter, clockwise and counterclockwise rotation, for tool holders HSK63F with collet chuck 462E/OZ25, cutter length up to 130 mm. Information: Machining unit MultiUnit with PowerBlock with 21/23 spindles, grooving saw and optional Profit milling unit. Connected load 12 kVA Rated current 17.5 A Fuse 32 A Voltage 400 V, 50 Hz, 3 Ph (without transformer) Network TN or TT Pneumatic connection 7 bar (102 psi). At the machine: coupling plug (quick coupling) ¼, DN7.2, brass, factory-supplied. For the machine: coupling socket (quick coupling) ¼, DN7.2, brass, customer side. Supply line, inner hose diameter 12 mm (min.). Compressed air consumption continuous operating air consumption approx. 230 L/min (approx. 3.8 L/sec) (compressed air). Extraction connection 3x extraction outlets dia. 80 mm. Extraction air velocity 30 m/sec - measured at the extraction outlet. Extraction requirement min. approx. 2500 m3/h. Machine weight approx. 1650 kg (with options!). Machine installation area: In general, a ProTec fix can be bolted to the floor. A concrete floor (or foundation) is required (at least at the four machine corners/feet). Equipment: Protec 571 Profit HSK63F with 3-position magazine. Roller table 765 mm (Y-axis), foldable, for machine front, width 500 mm. Roller table 765 mm (Y-axis), foldable, for machine rear, width 500 mm. Auxiliary stop 600 mm with integrated rollers for roller tables. Additional safety device with lamella curtain. Prerequisite for horizontal routing for Lamello P-System (without Lamello P-System tools). Drill bit set for Protec shank ø 10 mm with clamping surface (JSO) 1 HW-roof tip drill bit 5x70mm (NL 35mm), LH # 30566-5-05035-L 3 HW-dowel drill bits 5x70mm (NL 35mm), RH #30540-5-05035-R 4 HW-dowel drill bits 5x70mm (NL 35mm), LH #30540-5-05035-L 3 HW-dowel drill bits 8x70mm (NL 35mm), RH #30540-5-08035-R 5 HW-dowel drill bits 8x70mm (NL 35mm), LH #30540-5-08035-L 2 HW-dowel drill bits 10x70mm (NL 35mm), LH #30540-5-10035-L 1 HW-cup drill bit 15x70mm (NL 35mm), LH #30300-5-15070-L 1 HW-cup drill bit 20x70mm (NL 35mm), RH #30300-5-20070-R 1 HW-cup drill bit 35x70mm (NL 35mm), RH #30300-5-35070-R 1 HW-grooving cutter ø 125/30 mm groove width (SB) 4.0 mm, Z=12, LH, Leitz Only for chipboard and MDF, solid wood on request and subject to agreement Tool holder HSK63 F 3.00 pcs For collet 462E/OZ25 Collet 462E/OZ25 for shank 25 mm 3.00 pcs Indexable insert shank cutter Z1+1 1.00 pc HW with indexable insert drill tip ø20, S25, LH 120, L2/L3 58 mm Grooving cutter HW indexable inserts Z1 1.00 pc with indexable insert drill tip, D Ø 10 mm, d Ø 10 mm, L1 75 mm, L2 25 mm, L3 40 mm, RH (adapter 0571WAB10 to be ordered separat Crsdpfx Aisw Tfzfoled

Condition: used, Year of construction: 2019, Machine design: Throughfeed/Return feed Working area in X-direction: 1300 mm Working area in Y-direction: 5600 mm Working thickness (Z-dimension): 60 mm Number of main spindles: 1 Main spindle power: 5.5 kW Main spindle speed: 1000-20,000 rpm Clamping system: HSK-63 F Tool changer: Pick-up changer Tool change stations: 3 Back wall grooving units: fixed in Y-direction Vertical drilling spindles - in X-direction: 3 Vertical drilling spindles - in Y-direction: 10 Horizontal drilling spindle in X-direction: 2 Horizontal drilling spindle in Y-direction: 6 Control system: PC control Operating system: Windows Typewriter keyboard: Yes Mouse: Yes Programming system: Gannomat Editor DXF interface: Yes Online connection possible: Yes Table design: fixed, smooth table Central lubrication: automatic Tools: various tools Operating hours: 920 hours Weight approx.: 1800 kg Extraction diameter: 3x80 mm Crjdpfsymp N Tex Ailed Machine was modernized in the factory; pressure bar and control technology from model 0572! Storage location: Customer