Wide band grinding machines for sale
Your location was not identified (Edit)
|
3
working width: 1350 mm grinding belt width: 1370 mm grinding belt length: 1900 mm Weight of machine approx.: 6100 kg Electrical connected load: 63 kVA Ndjd2 Dimensions L x W x H: 2700 x 3100 x 2100 mm more
|
|
4
max. working width: 900mm Bfkw8qxjnz Grinding belt dimensions (W x L): 930x 1900mm Disc, diameter 1220mm Table opening: 0-150mm, Speed: grinding belt unit: 11 m/sec, disk unit: 22 m/sec, feed speed, frequency: 3-15 m/min., unit W grinding belt: 11kW, Aggrefat RD-disk: 4kW, feed motor, frequency: 2.6 kW, 400 volts, 50Hz, 110V, Dust extraction to 100 WS Grinding belt unit 1700 m3/h, discus unit: 1700 m3/h, vacuum table 1700 m3/h including used cartridge filter FKPF 48/6 V, built 2011 wit... more
|
|
2
Oberkochen, Germany
dealership location
17948 km
used
Working width 1360 mm Number of sanding units 2 St. sanding belt measurements 1380x2620 mm Motor roller 15 kW Motor pad 11 kW Control ja Wide Belt Sanding Machine Viet Model Challenge 223 1st unit: calibration and fine grinding roller Diameter: 320 mm 70 degrees Shore Motor power: 15 kW 2nd unit: Segmented fine sanding shoe electronically controlled 29 elements Nl829 Motor power: 11 kW, 2 running speeds Machine equipped with: - Band Cleaners [...] 2nd aggregate - Brush roller 150 m... more
|
|
9
Nuernberg, Germany
dealership location
17861 km
1992
used
working width 350 - 1300 mm workpiece height max. 150 mm bending speed 3-15 m/min grinding band dimension 1900x1330 mm workpiece length ab 350 mm workpiece width - max. 1250 mm plate thickness 0,3 - 1,00 mm grinding stand motor 16/19,00 kW transport motor 2,20 kW elevating motor Tischhöhe 0,37 kW control voltage 220 V voltage 380 V frequency 50 Hz total power requirement 56 kW weight of the machine ca. 2,50 t dimensions of the machine ca. 2,20x3,00xH2,20 m One point control, table movable and... more
|
|
8
Oberweis, Austria
17704 km
2007
ready for operation (used)
-with filter system -1st unit: Highly flexible ERNST grinding roller -2nd + 3rd unit: Loop flame boos -4th + 5th unit: Washing and dry station -max workpiece size (BxL): 1400 x 1540 mm Msajl9q7 -min. workpiece length: 350 mm -min. Workpiece length with magnetic or vacuum orbit: 80 mm -Workpiece thickness: 1-70 mm -Working height: 1000 mm -Feed speed: 2/4 m/min -Feed speed continuously: 1.5 -8 m/min -Volume tape filter unit: About 400 l -Compressed air connection: 3/8 " -Minimum p... more
|
|
7
Make: BÜTFERING Type: STEEL MASTER Built: 2001 Grinding width: 1350 mm Workpiece thickness: 0.5 - 120 mm Working height: 950 mm Grinding width: 1350 mm Grinding belt length: 1900 mm Total connection value: 65 kW Operating pressure: max. 8 bar Dimensions: approx. L 3.00 x W 3.00 x H 2.10 m Nn2u9 Weight: approx. 5.5 t All information without information. The machine is in very good condition. A pre-show is possible at any time in our exhibition hall. more
|
|
6
Material width: 1400 mm Thickness: 1 - 70 mm Weight of machine approx.: 4500 kg Dimensions L x W x H: 3200 x 3200 x 1800 mm Operating height: 1000 mm feeding speed: 4 / 8 m / min Bddh38pglx more
|
|
3
Dimensions: W x H x D: approx. 3200 x 2200 x 1000 mm, Working height: 850 mm, working width: 1500 mm, sheet length min.: 700 mm, sheet width min.: 500 mm, sheet thickness min.: 0.6 mm, sheet thickness max.: 4 mm, contact roller: 250 mm, counter-rolling roll hardness: approx. 50°shore, grinding belt: 2500 x 1600 mm , Belt drive motor: 16/23 kW, belt speed: 15/22.5 m/sec Feed speed with FU infinitely adjustable, from: approx. 4 - 16 m/min, suction: minimum suction volume: 50 cbm/min, suction noz... more
|
|
4
Oberkochen, Germany
dealership location
17948 km
used
Working width 1350 mm Number of sanding units 3 st. sanding belt measurements 1900x1360 mm Motor roller 15 kW Motor roller 11 kW Motor pad 11 kW Feed speed 3 - 15 m/min. weight 4000 kg Dimensions (L/W/H) 3000x2100x2000 mm Control Wide belt sander Bütfering AWS 3 K K-E / 1350 - grinding from above, 3 sanding belts - Sanding belt dimensions: 1360 mm wide / 1900 mm long - 1 contact roller unit, drive motor 15 kW, with calibration device and an automatic delivery roller D 200 mm, 85 ° Shore -... more
|
|
3
Wollerau, Switzerland
18098 km
reconditioned (used)
2 tape stations and a brush in the back to dust off. Vacuum gum conveyor belt electronic heights adjustment and electronically stepped segment shoe with 9 different programs. Cjb0cbwu Machine is in good condition. more
|
|
|
|
15
Lissmac metal grinding and deburring machine for deburring, edge lurking and finishing loops of aluminium, stainless steel and steel. Grinding in dry version with 2x wet suction from Ulmatec. Vsqibu The machine is ready for use immediately and has been serviced annually as part of the service contract. The machine only sanded aluminium and stainless steel. 4 aggregates (Aggr. can be switched on and off individually): 1.) Grinding unit -Finish loops, removal of slag, laser spl... more
|
|
3
Transverse width of the tape: 1330mm Tape length: 2620 mm working gap from 0.8 mm to 160 mm Table height 900mm Engine power of the first unit (tape) KW 10.5 / 14 Feed rate m / sec 10/20 Engine power of the second aggregate (tape) KW 10.5 / 14 Feed rate m / sec 10/20 Iyaga2hr Motor power of the third unit (brush) KW 11 Working feed m / sec 18 The motor power of the tape feed KW 2.2 Feed speed m / min 3-25 Motor power to adjust the table height KW 0.55 Motor brush oscillation power (... more
|
|
4
Cutting length max.: 1400 mm Bj2xde Thickness: 1-70 mm Weight of machine approx.: 4500 kg Dimensions L x W x H: 3200 x 3200 x 1800 mm more
|
|
5
Bad Schönborn, Germany
18035 km
1983
ready for operation (used)
Ernst wide belt sander with magnetic train One sanding drum, one replacement sanding belt, two counter-rotating VA wire brushes for edge rounding, leather strap very good condition / infinitely variable Bewbxo9ald Suitable extraction system with water filter Surcharge 1100.- + VAT more
|
|
3
Hohenbrunn, Germany
dealership location
17856 km
2010
as good as new (ex-display)
Low-cost entry machines for wet grinding with a working width of 600 mm for workpieces with max. 80mm height. 4 column table height adjustment motor synchronous setting the sheet thickness. The robust Qpzwrdzyo easy-to-use machine for the installer to achieve Oberflaechstenstrukturen. Standard equipment: -Digital display showing the set thickness, motorized, programmable setting of the sheet thickness about control -Emergency/off belt brake that stops within 3 sec. -Integrated drive un... more
|
|
6
Brush / wide-belt sander Fabr. ERNST Type EG3MW Machine number: 28111 Year of manufacture June 1985 Dry machine Technical data: Roller width 800 mm Effective working width 780 mm Clearance height 1-90 mm Speed 3-18 m / min Grinding roller diameter 420 mm Brush rollers diameter 250 mm Suction air volume without vacuum 0.8 m3/sec Operating pressure 5 bar My9l9 Sanding belt width 800 mm Power 13 / 15 kW Weight approx. 2100 kg Outer dimensions 2060 x 1750 x 2000mm more
|
|
8
Słupsk, Poland
17278 km
excellent (used)
The machine is used in the final machining of parts fired on a plasma cutter, laser, punched out on punching machines, cut on guillotines, etc. It is used for rounding sharp external and internal edges as well as polishing or satin finishing. Removes the grate, residue after cutting and all chips. The deburrer is equipped with 2 grinding units (abrasive roll and two brush rollers). Thanks to the magnetic tape, we can grind smaller parts. Standard equipment: new grinding paper, control panel, ... more
|
|
6
Elsterwerda, Germany
dealership location
17622 km
1998
good (used)
Working width: 1600 mm, workpiece height: 4-120 mm, Schleifbandmasse: je 1600x2400mm, contact roller, pillow dust brush. Drive 86Kw!. Automatic correction by upstream gauging station, including documentation, belts and a replacement roller. 2edydminm more
|
|
1
Wittenberg OT Bossdorf, Germany
17655 km
1990
good (used)
Wide belt grinding machine model OFZ-M1 900 Working width 900 mm Working height 850 mm Sanding belt size 950x2500mm Workpiece forward max. 150 mm minimum workpiece thickness 4 mm Length 2160 mm x height 1500 x width 1500 Weight 1800kg Power 25 kW, 220/380V, 50 Hz Nh3vx Compressed air supply 7 bar Sanding belts, are available, can be purchased with. Price negotiable more
|
|
1
Cylinder grinding machine Fabr. CARSTENS/RAIMANN type OKS 5 Fabr. # 1212/10465 built in 1975 Technical data: Working width 1300 mm Grinding unit grinding cylinder Tape speed approx. 30 m/s Drive 25 kW pneumat. Glider Uoqeozjq Drive 25 kW Brush rollers (with drive motor is powered by glide) Table speed infinitely variable regelb. 6-32 m / min Electr. Connection 380 V, 55 kW Space 2400 x 2750 x 2000 mm Weight approx. 4,5 t with -2 grinding units -compl. electrical device -comp... more
|
|
4
Breitbandschleif -, brush discharge Ridge and grinder Fabr. GRINDINGMASTER Type MCSB / B2 1300 Fabr. # 1431-04 TN year 1991 Technical data: Working width 1300 mm Brush size 1300 x 300 mm Sanding belt size 1900 x 330 mm Max material thickness 150 mm The contact roller 16 kW The stainless steel brushes with running oscillation 15 kW Performance of stainless steel brush co & opposite oscillation 15 kW Throughput speed continuously 3 - 18 m / min Air demand 70 l/min/6 bar T7sbdpvc... more
|
|
6
CNC-controlled belt sander Fabr. TAGLIABUE type TT-3-1300 Masch.# E6/36886 built in 1996 Technical data: maximum belt width 1300 mm Max passage 1300 mm maximum clearance height 350 mm variable feed speed 5.0-25 m / min. Sanding belt size 8500 x 150 mm Slat band size 6530 x 140 mm wide belt feed table 5000 x 1200 mm Band removal roller 4000 x 1400 mm Lrkjrrtxu 30 kW Weight approx. 6000 kg Machine width 5000 mm with CNC control Fabr. Syel -Vacuum extraction and filter unit serial... more
|
|
1
Broadband grinding machine Maxx 6 with 1100 mm working width (also available in other widths and equipment options) Bfapw3ezpy Variable feed Variable tape speed 1. Grinding unit 2. Planetary head unit 3. Grinding brush Table with constant height more information on demand more
|
|
2
Working width 1350 mm Number of sanding units 2 St. Workpiece thickness max. 3 - 160 mm Maec0nu7 sanding belt measurements 2200 x 1350 mm main drive 18,5 kW more
|
|
|
Didn't find what you were looking for? Please contact our partners for this category :
Dealer for Grinding machines
Dealer for Grinding machines
