Year of construction: 2026, condition: new, *Only the neodymium overbelt magnet is offered, not the conveyor belt underneath. *Neodymium magnets are among the strongest magnets in the world. They have an extreme pulling power and cannot be compared to ferrite magnets. Extremely high degree of separation, depending on the bulk height and the starting material. Probably the most compact overband magnet on the market. The competition often uses the less powerful ferrite magnets to save costs. dimensions approx. Length: 104cm Width: 22cm Height: 28 cm (at the motor) *Without controller Surcharge for simple manual start/stop control + 495 € A high-performance industrial neodymium magnet is installed. High-performance neodymium magnet approx. 600x68x36.5 mm * So nails are attracted to a length of 600 mm and thrown off to the side, in the area that is no longer magnetic. This overbelt magnet should be mounted approx. 5 - 9 cm above the material flow. *Assembly/suspension on site Ideal for separating nails from wood chips. Optionally also in a single-shaft shredder that is sucked off Requirements: Kodpfx Ajdubpuefgolt *Your belt width or useful width inside (of the existing conveyor belt) should ideally be narrower than 55 cm *Suitable for separating nails from material flows that are less than 12 mm high and with a chip length of less than 25 mm. ----- Optional at extra charge: Cross and ascending belt demonstrators from € 7,995 net

Condition: as good as new (ex-display), Year of construction: 2024, Special-purpose machine for plastics shredding Base machine from €24,990 net Ideally suited for shredding: - Paper, cardboard, pipes, profiles, boxes, canisters, buckets, cans, wooden pallet offcuts, etc. - Medium-hard thermoplastics such as PVC, PP, PE, PS, PU, PET Included: - Special rotor with embedded knives (reduced load uptake) - Minimal cutting gap between rotor and counter knives Motor: 18.5 kW; 400 V - 50 Hz - 3 ph Control: PLC Cutting chamber opening at the top: 600 x 800 mm Maximum recommended input material size: approx. 500 x 500 mm (*height less critical) Hydraulically actuated pusher Screen perforation options: 25 - 40 mm For plastics, coarser screens are recommended (30-40 mm) *For finer granulation, a two-stage shredding process with downstream granulator type MVZ (screens 5-15 mm) is recommended Exhaust port Ø 160 mm Weight: approx. 1,300 kg Dimensions (LxWxH): approx. 1737 x 1167 x 1650 mm Additional options available at extra charge: - Raise shredder by approx. 25 cm (preparation for conveyor discharge): + €1,980 net - Inclined conveyor belt (discharge height approx. 220 cm): + €8,770 net - Overbelt magnet: + €5,980 net - Conveyor and overbelt magnet control: + €2,750 net (synchronized start/stop with shredder) - Alternatively, manual start/stop function at conveyor: + €595 net Raw material requirements: - Moisture content (atro) must be below 25% - Metals and mineral contaminants such as sand, stones, etc. will result in increased wear We are happy to offer a free test using your material at our facility in Neckartailfingen. Alternatively, you may send your material to us via freight forwarder and we will document the test using photos and videos. --- * Only for brittle plastics of medium hardness. * Not suitable for elastic or extremely hard and heavy plastics – this will negatively impact the durability of the system. Klodpod H R Sxefx Afget --- Optional: Larger machine sizes available Base machine: Shredder MGZ 830 K-S – 18.5 kW Cutting chamber opening at the top: 800 x 1,000 mm Maximum recommended input material size: approx. 720 x 700 mm (*height less critical) From €39,995 net (*options subject to additional cost) Base machine: Shredder MGZ 1030 K-S – 22 kW Cutting chamber opening at the top: 1,000 x 1,000 mm Maximum recommended input material size: approx. 900 x 700 mm (*height less critical) From €49,975 net (*options subject to additional cost) Base machine: Shredder MGZ 1330 K-S – 37 kW Cutting chamber opening at the top: 1,300 x 1,200 mm Maximum recommended input material size: approx. 1,200 x 700 mm (*height less critical) From €79,975 net (*options subject to additional cost)

Condition: as good as new (ex-display), Year of construction: 2024, Primary crusher Basic machine starting from € 29,950 net *Options against surcharge Ideal for pre-crushing bulky materials such as pallets, boards, beams, fruit crates, polystyrene, plastics and much more. For the production of wood chips, the primary crusher can also be installed directly above a single-shaft shredder Machine in pre-production * Special options available at extra cost Your advantages: + Volume reduction of up to 70 + Significantly lower transportation costs Kodjfd Iciopfx Afgolt + Low disposal costs + Production of fuel material + Also ideal upstream of a single-shaft shredder for the production of wood chips Weight: 1,200 kg Dimensions 2050x850x1600 mm Cutting unit opening 1300x700 mm *Optionally also available in 1600x700 mm (motor then 11 kW) (surcharge + 4.995 € net) Throughput: up to 50 pallets/pieces per hour *depending on material Motor: 7.5 kW Options: Industrial top hopper (closed on 3 sides) + € 4,950 net Extra emergency / off button + 495 € net 200 mm extension + 497 € net Requirements for the raw material: - Moisture content less than 30 % ATRO - The machine must be installed in accordance with CE guidelines or secured on site against access from below (into the cutting unit) - Pallets up to a dimension of 1200x800 mm can be processed Longer parts also work on edge

Condition: new, Year of construction: 2026, Your advantages: + extremely large cutting unit opening with 1300x1200mm + special rotor suitable for hardwood and softwood + Energy-efficient and powerful with 37 kW at start-up Technical specifications: Colour: grey / blue Feed opening (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Power requirement (kW): 37 Kedpfegbkkrex Afgslt Screen perforation (mm): 30 - 50 mm - selectable Tools: 37/70 knives Extraction nozzle Ø (mm): 200 mm Dimensions: 2430x2410x1735 mm (lxwxh) Weight (approx. Kg): 3,920 Optional for a surcharge: * to shred veneer or paper (anything thinner than 3 mm) - we recommend a segment floor. The machine in preproduction has not yet installed this. Special option at an additional cost. - 2nd row of knives, for up to 30% more throughput - Fast hydraulics, for increased throughput - Preparation for conveyor belt removal - conveyor belt - HAWK-EYE overbelt magnet --- Optimal pallet size with the option slide extension = 1200x1400 (option slide extension, the cutting unit opening 1300x1700 surcharge + 12,975.00) * is associated with significantly longer production time. * larger machines on request --- Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: new, Year of construction: 2026, Briquetting press NEM 900: production time appr. 5 months for briquetting aluminum chips Throughput: up to maximum 320 kg / h * more details after a free test with heard material . Briquette diameter: Ø 70 mm Optimal briquette length: 70 mm Ksdpjgfm Ryefx Afgolt . Technical specifications: Total connection: approx. 31 kW In continuous operation approx. 22 kW 400 volts / 50 Hz / 3 phases Pump: 120 + 60 liters per minute Silo: 1 m³ Silo rollers: 1200 mm Including agitator Oil tank: 600 liters Dimensions: 2500 x 1700 x 1730 mm lxwxh Weight: 2250 kg. Hydraulic pre-compression via slide Main press cylinder Vertical cylinder Above for connecting a cooling unit . One and the source material - max.span: 18 mm - Excessive temperature: temperate room at at least + 5 ° C. - max.weight on agitator: 200kg. - The loading must be free of metals and mineral impurities such as sand, stones, etc. This on the pressing tools and / or responsible wear can result

Condition: as good as new (ex-display), Year of construction: 2022, Briquetting press for aluminium or steel chips Extremely high pressing force of 3,700 kg/cm² Large hopper: 600 x 1,500 mm Briquette size: 60 x 40 mm Throughput: Aluminium chips – up to 70 kg/h Kodpfxow Ig Sue Afgolt Steel chips – up to 180 kg/h Brass chips – up to 220 kg/h *depending on input material and settings Includes: - Emulsion tray - Emulsion pump - Oil cooler

Condition: like new (used), functionality: fully functional, Year of construction: 2025, operating hours: 55 h, Machine with special rotor Available immediately Benefits: + Special rotor with reduced knife protrusion, suitable for hard and soft materials + 22 kW motor + Efficient square knives *For pallets: up to a maximum of 10 pallets per hour *Rate depends on screen size and material. Significantly higher throughput with smaller wood residues. Motor: 22 kW; 400 V - 50 Hz - 3 phase Screen: 15/20 mm or according to agreement (10 to 40 mm possible) Hydraulically operated pusher Current screen perforation (15/20 mm) *can be changed Suction connection Ø 200 mm Kedpfx Afox Af Rdjgelt Feed opening: 1000x1000 mm Dimensions: 2000x1800x1645 mm Sample image above: plant color may differ Weight: 1920 kg Standard scope of delivery includes: - Control cabinet with PLC control - Automatic star-delta start - High-speed hydraulics - Auto shut-off when rotor is idle - Speed 70–90 rpm for high throughput - Cycle control to prevent idle times - Performance-enhancing step control for the hydraulic pusher - Pertinax guides for hydraulic pusher - Vibration-damping machine feet - CE compliant The following options are available at an additional cost: - Increase shredder height by 30 cm (preparation for conveyor belt) + €2,480 net - Angled conveyor belt (discharge height approx. 220 cm) + €12,980 net - Overband magnet + €5,980 net - Control system for conveyor belt and overband magnet + €2,750 net (start and stop synced with shredder) - Enlarged hopper attachment 1500x1500 mm + €3,480 net Raw material requirements: - Moisture content (atro) must be below 25% - Feed must be free from metals and mineral contaminants. Tool damage and/or increased wear may result otherwise.

Condition: new, Year of construction: 2026, Consisting of a bale shredder for large round bales, type MHB, and a straw shredder, type MHZ 1) Bale Shredder MHB: Special price starting from €22,975 net (manufacturing time approx. 15 weeks) Suitable for round or rectangular bales. Includes a frequency converter (FU) – this regulates the speed of the shredding floor. The bales are placed on the shredding floor, and the feed of the shredder is activated. The tines of the shredder tear the straw from the bale and fling it into the hopper. Ideally, the combination of bale shredder and straw shredder is recommended here. Technical data, bale shredder: Performance: 1-2 bales per hour up to a maximum of 600 kg per hour (depending on the screen size used in the straw mill, kW, number of straw mill). Without a straw mill, the bale shredder can even process up to a maximum of 900 kg/h of straw. Maximum size of rectangular bales: 2400x1200x800 mm (l x w x h) Shredder motor: 5.5 kW, 380 volts Shredding floor feed: 0.75 kW, 380 volts Dimensions: 3750x1730x2460 mm (l x w x h) Weight: 400 kg 2) Straw Shredder MHZ 600 - 11/15 kW; immediately available Special price starting from €6,995 net Surcharge for the even larger straw shredder (18.5 kW) + €2,750 net Technical data, MHZ with special hopper: Motor: 15 kW, 380-volt electric motor Diameter: 600 mm Hardened cutting knives Screen with interchangeable inserts Optional (10, 12, 15) 22, 30, 45 mm aperture With star-delta switch, overload protection, and 8 m power cable, ready for connection Discharge nozzle: 160 mm Discharge distance: approx. 12 m Dimensions: approx. 1600 x 1020 x 1360 mm (l x w x h) Weight: approx. 240 kg --- Options available at an additional cost: Infeed auger + €970 net Klodpfxsb Nulhs Afgot Cyclone (mounting on site by customer) *should be located a maximum of 10 m away + €2,970 net Simple filter: €1,750 net --- Further options: Industrial dust extraction system (demonstration model) + starting from €9,950 net Optional with rotary valve *makes the material pressure-free + €5,750 net Control system: starting from €1,620 net Special shredder extension, 3 m *other sizes will be calculated + €9,750 net Briquette press MPP 180 S; little used demonstration model 70 mm briquettes - up to a maximum of 100 kg/h Starting from €39,700 net * larger machines on request --- Description: The muetek bale shredder was developed for shredding round and rectangular bales of hay and straw. The shredder flanged onto the bale shredder shreds straw from all types of cereals, hay, corn, and miscanthus. The muetek machines in the MHZ/MHB series are characterized by their robust construction and solid design. muetek bale shredders in the MHB series are equipped with a chain conveyor, onto which the straw bale is placed using a front loader. The support is adjustable depending on the type of bale. The chain conveyor presses the bale against the shredding rotor; the feed speed is adjustable. The shredding rotor is equipped with several tines that tear open the straw bale. The straw separated from the bale is discharged. --- In principle, the machines work for dry raw materials: - Straw - Hay --- Shredding hemp only works with a special shredder Surcharge approx. €9,720 net *depending on the design. Shredding hemp does not work with the straw mill. Requirements for the raw material: Moisture content maximum 12%

Condition: reconditioned (used), Year of construction: 2023, All wear parts new only 704 operating hours Special price for a low-hour demonstration unit Base machine: €29,990 net Optional extras (for an additional charge): - Cooling unit: €3,995 net - Emulsion tray: €3,990 net The hydraulic briquetting presses of the MPP NEM series compact materials such as aluminum, copper, brass, bronze, graphite, and other non-ferrous metals into dimensionally stable cylindrical briquettes. These machines are distinguished by their robust construction, ensuring consistent briquette quality during continuous operation. The pressing process does not require any binding agents – compaction is achieved solely through hydraulic pressing force. Depending on material, the feedstock volume can be reduced by up to 90%. Throughput capacity: maximum 70 kg/h (depending on material) Briquette diameter: Ø 50 mm Motor: 5.5 kW 400 Volt / 50 Hz / 3-phase Pump: 40 liters Maximum briquette length: 50 mm Optimal briquette length: 40 mm Silo diameter: 1,000 mm Oil tank: 110 liters Dimensions: 1750 x 1130 x 1100 mm (L x W x H) Weight: 950 kg Hydraulic pre-compaction via slide Main press cylinder Vertical cylinder Kjdpfx Afod N Dnhogslt Fill level sensor: yes Feed material requirements: - Max. chip length: 15 mm - Installation room temperature: heated space, at least +5°C - Max. load on agitator: 150 kg - Feed material must be free from magnetic metals and mineral contaminants such as sand, stones, etc. Damage to pressing tools and/or increased wear may otherwise occur.

Condition: as good as new (ex-display), Year of construction: 2023, Ideal for shredding polystyrene or similar materials Throughput depends heavily on the sieve and source material: - up to 60 kg / h for EPS with a 15 mm sieve *the coarser the sieve, the higher the throughput Motor 9.2 / 11 KW - 400 volts, Kedpfx Afoh S H T Ujgolt stable steel construction, hardened cutting blades, sieve with interchangeable inserts, optionally (8), (10), 15, 22, 26, 30, 40, or 60 mm perforation with electric drive with star-delta switch Ue protection and 8 m supply line ready to plug in, blow-out nozzle 150 mm, optionally for plastic or grain pipes, blow width approx. 12 m, chassis with 2 running wheels Ø 380 mm, and a swiveling support wheel Ø 125 mm, all Wheels with solid rubber tires, Dimensions approx. 1200 x 900 x 1270/1400 mm lxwxh Weight approx. 240 KG, Spare parts prices and options: 24 blades, hardened €9.90 each net 6 bolts €14.90 each net 1 sieve €475 each net Lid €290 each net

Condition: good (used), Technical specifications: Kodpjwtdk Tofx Afgslt Briquetting press in good condition Year of manufacture: 2007 Technically inspected in 06 / 2025 Cylindrical briquette: 80 mm Throughput up to max. 150 kg/h *only approx. 3,949 operating hours - Hydraulic press: briquetting press with discharge chute - Hydraulic unit: 4 kW - Pressure: max. 300 bar - Transport dimensions: 1585/2140/H1940 mm - Weight: 1,370 kg Functional guarantee upon handover We are happy to arrange a free test run!

Condition: new, Year of construction: 2026, The ideal machine for shredding softwood. Kjdswzarcjpfx Afgelt Motor: 11/15 kW; 400 V - 50 Hz - 3 ph, Rotor diameter: 260 mm, Hydraulically actuated pusher Screen perforation to choice (12 - 40 mm) Extraction port Ø 160 mm Weight approx. 1,100 kg Dimensions (LxWxH) approx. 1805 x 1118 x 1650 mm Colour: blue / grey Requirements for raw material: - Moisture content (atro) must be below 30% - Metal and mineral contaminants such as sand, stones, etc. lead to increased wear. We are pleased to offer a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material by freight and we will document the test with photos and videos.

Condition: as good as new (ex-display), Year of construction: 2025, showroom machine machine available Advantages: + special rotor with reduced knife protrusion + Motor 22 kW + effective square knife * for pallets: up to 10 pallets per hour * depending on the sieve and material. With smaller residual wood, significantly more. Engine: 22 kW; 400 V - 50 Hz - 3 ph, Sieve: 15/20 mm hydraulically operated slide Current screen perforation (15/20 mm) * can be exchanged Extraction nozzle Ø 200 mm. Feed opening 1000x1000 mm Dimensions: 2000x1800x1645mm Example image above: The color of the system may vary Weight: 1920 kg. Included as standard: - Control cabinet with PLC control - automatic star / delta start - fast hydraulics - automobile. OFF when the rotor is idling - Speed ​​70-90 rpm for high throughput - cycle control to avoid idle times, - performance-increasing step control of the hydraulic slide, - Pertinax guides for hydraulic slides, - vibration-damping machine feet, - CE conform. The following options are available at an additional cost: - Additional row of knives + € 2,790 - segment bottom + € 6,890 (recommended for materials with a wall thickness thinner than 3 mm) Kedpfsdv Eu Hjx Afgslt - Special K-rotor storage + € 3,480 If necessary, consider shredding plastic with sieves smaller than 15 mm or with a lot of fines. If the bearings are lubricated with grease every approx. 4 weeks in operation, this is not necessary) - Raise the shredder by 30 cm (preparation for conveyor belt) + € 2.480 net - Angled conveyor belt (discharge height approx. 220 cm) + € 12.980 net - Overbelt magnet + € 5.980 net - Control conveyor belt and overbelt magnet + € 2.750 net (Start and stop synchronized with the hacker) - Exhibition hopper 1500x1500 mm + € 3.480 net Requirements for the raw material: - The moisture content (atro) must be below 30% - The loading must be free of metals and mineral impurities. This can result in damage to the tools and / or increased wear

Condition: new, Year of construction: 2026, Single-shaft shredder MRZ 530 Included: + Profile rotor for increased throughput Options: Double knife row + €895 net Veneer and paper stripper + €970 net * recommended for extremely thin materials with a thickness less than 3 mm Our mütek single-shaft shredder MRZ 530 processes a wide variety of materials such as all types of wood residues, softwood, chipboard and MDF, pallets, construction timber, demolition wood, carpets, cables, paper, cardboard, and plastics. The machine is characterized by its robust design, ensuring consistent quality in continuous operation. We are pleased to offer you a free test with your material. You are welcome to visit us in Neckartailfingen for this purpose. Alternatively, you can send us your material via freight and we will document the test with pictures and videos. Kedpfx Asd Db N Iefgolt Machine data: Motor: 15 kW; 400 V - 50 Hz - 3 phase Knives: multiple reversible Rotor diameter: 260 mm Control: Siemens S7-1200 PLC Hopper (mm): 510 x 810 mm Hopper volume approx. 0.4 m³ Throughput: 1 - 5 hopper fillings/hour Hydraulically operated pusher Screen perforation as desired (10 - 40 mm) Extraction nozzle Ø 160 mm Weight approx. 1,000 kg Dimensions approx. 1550 x 1100 x 1640 mm Moisture content of raw material: must be below 30% a.d. Standard features included: • Fast hydraulics • Profile rotor • Control cabinet with Siemens PLC control • Automatic star-delta start • Automatic shut-off in case of rotor idle • Removable extraction channel • Speed 70 - 100 rpm for higher throughput • Cycle control to prevent idle time • Performance-enhancing step control for hydraulic pusher • Stable guides for hydraulic pusher Additional shredder options: - Raise shredder by 30 cm (preparation for conveyor belt) + €1,980 net - Angled conveyor belt + €8,770 net Horizontal section: 1200 mm Inclined section: 2500 mm Angle: adjustable 0-60 degrees Discharge height: approx. 2000 mm ± 100 mm - Overband magnet + €5,980 net - Control for conveyor belt and overband magnet + €2,750 net (start and stop synchronized with the shredder) Requirements for input/raw material: - Moisture content (a.d.) must be below 30% - Metals and mineral impurities such as sand, stones, etc., lead to increased wear

Condition: new, Year of construction: 2026, Delivery time approx. 3-4 months MRZ 830 Shredder Custom tariff number: 84659600 Feed opening 800 x 1000 mm Motor: 18.5/22 kW; 400 V - 50 Hz - 3 ph Blades: multi-rotatable Hydraulically operated slider Screen perforation of your choice (10 - 40 mm) Suction nozzle Ø 200 mm Weight approx. 1,600 kg Klsdod Dgw Uopfx Afgjt Dimensions (L x W x H) approx. 2,290 x 1,420 x 1,750 mm Turbo clutch Included as standard: - Automatic star/delta start-up - Fast hydraulics - Auto. OFF when the rotor is idle - Speed 70-90 rpm for high throughput - Cycle control to avoid idle times - Performance-enhancing step control of the hydraulic slide - Pertinax guides for the hydraulic slide - Vibration-damping machine feet - CE compliant . The shredder is designed for shredding natural wood, particle board, and MDF, as well as other materials after testing and approval by the manufacturer. Additional shredder options: - Raise shredder by 30 cm (prepared for conveyor belt) + €2,140 net - Articulated conveyor belt + €8,770 net Horizontal section: 1,200 mm Rising section: 2,500 mm Angle: adjustable from 0-60 degrees Discharge height: approx. 2,000 mm + - 100 mm - Overbelt magnet + €5,980 net - Conveyor belt and overbelt magnet control + €2,750 net (Start and stop synchronized with the shredder) Raw material requirements: - Moisture content (dry) must be below 30% - Installation temperature: temperature-controlled room at least +5°C - Metals and mineral contaminants such as sand, stones, etc. lead to increased wear

Year of construction: 2025, condition: new, to sell the demonstration machine at a special price Our MVZ 7.5 granulator is suitable for shredding thin-walled parts and/or for post-shredding wood chips. More details after a test with your material. Larger systems are also available as an option The price is only for the shredder as shown in picture 1 - fan, cyclone and filter are options. Motor: 7.5 kW *larger systems on request (4 to 75 kW) Throughput up to 120 kg/h *depending on screen and material Much higher throughput rates can be achieved with the secondary shredding of wood chips. Details after the test with about 30 kg. Rotor diameter: 180 mm 6 rotary knives each 225 mm 4 stationary knives each 225 mm Dimensions: 930x730x1420mm Klsdpfxed N Dn Dj Afgst weight: 450 kg, suction nozzle: 100 mm, Screens: 6.8 and 15 mm - other screens available, Price per sieve: €390. Price set replacement knife: 579 € Suitable e.g. fur: - Plastic waste of all Art.-No Various materials - HDPE, LDPE, PP, PS. PC, PA - biomass -Wood - Herbs etc. Parts from injection molding, blow molding, injection molding scrap, small bottles, cables, small pipes, profiles, etc

Year of construction: 2024, condition: new, Overview - of the different variants *Not every position is required: Optional: -Bale shredder MHB from 24.990 € net -MHZ straw mill from € 7,980 net -Special hopper 970 € net -Cyclone from € 3,750 net -Sheet metal silo demonstrator with discharge (only sketched in the picture) *optional, if you want to load with the wheel loader Unit price net from € 14,750 - Demonstrator -Dedusting auger - length approx. 4 m 4 sieves are mounted on the underside, which are extracted. Unit price net from: 9.750 € - Extraction parts / hoses flat rate 945 € net - Complete control system Net unit price: € 2,750 -Demonstrator extraction unit MMJET 160 Demonstrator, with cleaning Connection 160, fan 2,2kw air capacity 1850m³ /400 V Automatic compressed air cleaning Unit price net from: 6.950 € -Baler B 400 Bales approx. 400x400x800 (height adjustable) Up to 30 bales per hour with + - 20 kg from 59.995 € net *A reference system (baler) is located in zip code: 64579 Gernsheim Technical data: Bale size (WxDxH): 400 x 400 x 800 (height can be adjusted on request) Bale weight +/- 20 KG (depending on material) Capacity: approx. 30 bales per hour Storage container approx. 0.7m³ capacity Filling level sensors for min./max. filling level in the container Hydraulic pre-compressor Hydraulic compression ram Hydraulic unit, valve block with oil tank Pump 18.5 KW / 50 liters Rollers in the bale chamber for easy bale push-off Dimensions (l x w x h) 3105x2830x2455 mm Ksdpfeff Sbiex Afgjlt Weight approx. 1500 KG mütek baling presses / wrapping machines are designed for the production of bales from a wide variety of materials such as shredded micanthus or elephant grass, wood chips, sawdust and shredded straw. straw. The machine is characterized by a robust design that guarantees consistent quality in continuous operation. quality in continuous operation. The baler compacts the material filled into the storage container without the addition of binding agents and packs the material into plastic bags. The volume of the material can be considerably with the baling press. The volume reduction rate depends on the material. The maximum material moisture content must not exceed 18 % Atro. The container of the mütek baler can be fed automatically or manually and has a volume of approx. 0.7 m³. volume of approx. 0.7 m³. Containers with a larger volume or with an attached suction and filter system as a complete disposal unit are also available. In addition to automatic filling via deduster, mütek also offers filling by means of screw conveyors. With both variants, automatic automatic dedusting is possible. mütek baling presses are equipped with a control cabinet for the control system. In the standard version, the dimensions of the bales (width x depth x height) are 400 x 400 x 800 mm. However, the height can be adapted to your requirements on request. The following advantages arise in the production of bales: - simple and safe storage - No loose dust - Minimization of the storage volume - Low transport volume *Requirements for source material: - dry (max. 30 % ATRO) - Maximum length 35 mm

Condition: as good as new (ex-display), Year of construction: 2023, The ideal machine for shredding cables including optimized cutting geometry approx. 9 operating hours Motor: 18.5 kW; 400 V - 50 Hz - 3 ph, Blades: 14 pieces, 40x40mm, multi-rotatable, Rotor diameter: 260 mm, Kodogmfa Ajpfx Afgslt Control: Omron SPS, Cutting unit opening 600 x 800 mm, hopper volume approx. 0.6 qbm, hydraulically operated pusher Screen perforation of your choice (15 - 40 mm) Suction nozzle Ø 160 mm Weight approx. 1,300 kg Dimensions (lxwxh) approx. 1737 x 1167 x 1650 mm The following options are available at extra cost: - Double row of knives + 995 € net (28 instead of 14) - Surcharge for 4-sided segment base + € 3,750 net (prevents blocking of the pusher. Recommended for shredding plastics, paper, veneer with a thickness of less than 3 mm). - Raise shredder by 30 cm (preparation for conveyor belt) +1,980 € net - Angled conveyor belt (discharge height approx. 220 cm) + €8,770 net - Overbelt magnet + € 5,980 net - Conveyor belt and overbelt magnet control + € 2,750 net (start and stop synchronized with the chipper) Bea9ia3l27 Requirements for the raw material: - Mineral impurities such as sand, stones, etc. lead to increased wear. We are happy to carry out a free test with your material and invite you to visit us in Neckartailfingen. It is also possible for you to send us your material by freight forwarder and we will document the test with pictures and videos.

Condition: new, Year of construction: 2026, Extremely powerful industrial magnet for iron separation Special price: €990 net (shipping €14.90 net) *Construction lengths can be found in image 2 The active side is equipped with a stainless steel end plate (material 1.4301). Threaded holes are provided on the rear side for mounting; *handle available on request The block magnet systems can be used at temperatures of up to max. +100°C operating temperature. The magnet surface should be cleaned regularly from captured iron parts. Pickup distances for all types, for example: For a steel nut M5: approx. 60 mm For an M5 x 30 screw: approx. 100 mm Mounting example 1: Mounted above a conveyor belt, 'iron parts jump onto the holding surface of the magnet.' Mounting example 2: Mounted within a pipeline system with direct contact to the material flow. For maximum separation safety, a cascade setup of multiple block magnets in series is possible. Assembly and safety instructions: When handling, already upon unpacking and later during installation, ensure that there are no loose iron parts, such as tools or screws, nearby. Klsdpfetqfhxjx Afgst The magnetic force is so strong that painful injuries may occur if fingers get caught between iron parts and the active surface. There should be no steel parts under the active surface within a minimum distance of 400 mm.

Condition: new, Year of construction: 2023, Length: approx. 2500 mm Width: approx. 400 mm Discharge height: approx. 1650 mm Weight: 290 kilograms Motor: 0.75 kW Ex works prices Shipping as per effort Ksdpfx Aev Srvvefgelt

Condition: used, Shredding Machine MGZ 1330, 37 kW Operating hours: 275 Included: - Second knife row - Fast hydraulics for increased throughput - Preparation for conveyor belt Optional: - Conveyor belt with automatic metal separator Your advantages: + Extremely large cutting chamber opening; top: 1300x1200mm + Special rotor suitable for both hardwood and softwood + Energy-efficient and powerful, 37 kW start-up power Technical data: Feed opening, top (mm): 1,300 x 1,200 Hopper capacity (cbm): 1.6 m³ Rotor diameter (mm): 368 Rotor speed (rpm): 65 - 125 Kodox Tfdhopfx Afgolt Power requirement (kW): 37 Screen hole size (mm): configurable Tools: 37/70 knives Extraction connection diameter (mm): 200 mm Dimensions: 2430x2410x1735 mm (LxWxH) Weight (approx. kg): 3,500 --- Feedstock requirements: - The moisture content (atro) must be below 20% - The feed material must be free of metals and mineral contamination. Damage to the tools and/or increased wear may result.

Condition: used, Waste compactor, baler, waste baler, chamber baler, Orwak Compactor 3110, used machine Manufacturer: ORWAK (Sävsjö, Sweden) Kedpey S Ui Dofx Afgslt Type: Compactor 3110 Serial No: 105441 Product No: 4903110-00 Overall dimension: 865 x 680 x 2050 mm -press force: 4t -production date: 2011-11 -voltage: 230 V -frequency: 50 Hz -power: 1.1 kW -current: 8.9 A -weight: 340 kg

Condition: good (used), functionality: fully functional, “Steinert NES 150 210 E 6119” for Sale Manufacturer: Steinert Type: NES 150 210 E 6119 Belt widthness: 1.500 mm (New belt) With control-unit. Overhauled, balanced, sandblasted and painted. Kledey S Tv Njpfx Afgst

Condition: used, Technical data feed hopper with hydraulic moving floor and bag opener for recyclables from yellow bags and residual waste: Manufacturer BRT HARTNER GmbH Type HP5-3035 Year of construction 2015 Hopper volume 30 m³ Drive line 17.5 kW Dimensions in current state 13,200 x 3,050 x 4,350 mm (l x w x h) Condition of the machine: The feed hopper with bag opener was used at a large recycling plant, where recyclable materials from yellow bags or commercial waste were tipped into the hopper using wheel loaders, the bags were opened using the bag opener, and the recyclable materials were transported to a sorting plant or the commercial waste was transported in measured quantities for further processing. The system functioned flawlessly until it was dismantled and replaced with a larger system with higher throughput capacity. The machine was dismantled into individual parts in our workshop, partially overhauled, reassembled, and tested during operation. The following overhaul work was carried out and the following spare parts were replaced: Dismantling of the feed hopper and bag opener into individual parts. Cleaning, partial sandblasting, priming and painting of the steel parts. Various wear and cover plates were newly manufactured and installed. Cutting off the worn ends (approx. 40cm) of the push floor pipes. Welding on the new pipes and smoothing the push floor pipes. Replacement of all plastic sliding plates for the hydraulic push floor. Removal of the hydraulic unit from the push floor, emptying of the hydraulic oil tank, replacement of the oil filters, refilling with new hydraulic oil. Replacement of the three hydraulic blocks, all valves, the oil sight glass and all hydraulic hoses from the hydraulic unit. The seal kit and hydraulic hoses were replaced on all three hydraulic cylinders of the push floor. All six limit switches (proximity sensors) on the push floor were replaced. Klsdpfx Afjy S Rw Djgjt The conveyor chains on the left and right of the scraper conveyor were replaced. Seven carrier bars on the scraper conveyor were replaced. The drive motor for the ripper blades was replaced. All nine pneumatic cylinders for the pressure pipes were replaced. All pneumatic lines and connections were replaced. All of the plastic sliding plates for the hydraulic operation of the bag opener were replaced. The bag opener can be moved vertically so that the system can also be used for commercial waste or residual waste without the bag opener. The side impact protection plates on both sides were replaced. Various wear parts of the bag opener have been replaced. The entire system has been rewired and reconnected. The system control in the control cabinet has been retrofitted by the manufacturer BRT Hartner to a self-sufficient individual control system and the standard programme has been reloaded into the control system. The system has been commissioned and tested by the manufacturer BRT Hartner, see the function video. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: refurbished (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, year of last overhaul: 2025, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Kledpfxoy S Rv To Afgst Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.