Used multi spindle machines for sale (197)

Condition: ready for operation (used), Year of construction: 2002, operating hours: 63,040 h, functionality: fully functional, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Machine configuration Upper linear slides: 2 units Milling unit: 1 unit Transverse drilling units: 2 units Rigid front spindle: 1 unit Machining units Drum 6: Movable only in the X-axis Front position 1: Rotationally rigid spindle, movable only forwards and backwards Front positions 2 to 4: Rotationally fully controllable spindles Front position 5: Internal machining axis for processing internal contours and radii Front position 6: Driven indexing spindle with rear machining slide and two tools, movable towards the viewing side Full electronic equipment Electronically connectable auxiliary drives on the front positions and six drum slides Dwedpfozrgnpox Akvea MACHINE DETAILS Operating hours: 98,119 h Spindle hours: 63,040 h EQUIPMENT Chip conveyor High-pressure coolant unit Bar loader Milling unit Two transverse drilling units Collets Spare parts Electronic components for the control cabinet New rigid front spindle

Condition: good (used), Year of construction: 2014, TORNOS Delta 20/5 III multi-spindle turning machine with FANUC Oi-TD control, serial number 52100249, year of manufacture 2014, operating hours estimated at approximately 16,047 hours according to management, chip conveyor, bar feeder SFB 320e. Dwjdpfx Aksztdgfevsa

Condition: good (used), Year of construction: 2011, Turning center TORNOS Delta 20/5 III with FANUC Oi-TD control, serial number 52100222, year of manufacture 2011, operating hours estimated at approximately 19,061 hours according to management, chip conveyor, bar loader Robobar SFB-320. Dwsdpfx Akjztdf Iovea

Condition: good (used), Year of construction: 2014, See documents. Dwsdpfxezqtg Aj Akvja List of individual machines with operating hours, etc. – see documents.

Condition: ready for operation (used), Year of construction: 2011, spindle motor power: 25,000 W, spindle speed (max.): 6,000 rpm, bar diameter (max.): 65 mm, travel distance X-axis: 210 mm, travel distance Y-axis: 110 mm, swivel angle B-axis (max.): 820 °, number of axes: 12, This 12-axis MORI SEIKI NZ2000 ST3Y3 was manufactured in 2011. It features a maximum machining diameter of 200 mm and a maximum machining length of 260 mm. The machine is equipped with twin spindles and three turrets, providing efficient multi-spindle turning capabilities. If you are looking to get high-quality turning capabilities, consider the MORI SEIKI NZ2000 ST3Y3 multi-spindle turning machine we have for sale. Contact us for further details. • Working capacity: • Max machining diameter: 200 mm • Max machining length: 260 mm • Axis travel: Dsdpfezpxupox Akvowa • Z-axis: 300 / 810 mm • B-axis (two spindles): 920 mm • Spindles: • Spindle power: 22 / 25 kW • Counter spindle: Yes • Feed rates: • Rapid traverse X / Z: 30 / 50 m/min • Driven tools: • Driven-tool power: 5.5 / 7.5 kW Additional equipment • TOP AUTOMAZIONI bar feeder (2018) • Chip conveyor Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2008, spindle motor power: 26,000 W, spindle speed (max.): 3,500 rpm, bar diameter (max.): 76 mm, total width: 2,210 mm, total height: 2,480 mm, overall weight: 12,700 kg, controller manufacturer: FANUC, controller model: Series 31i-MODEL A, product length (max.): 4,050 mm, number of axes: 8, This 8-axis DOOSAN PUMA TT2500SY was manufactured in 2008. It features a maximum turning diameter of 390 mm on the upper turret and 300 mm on the lower turret, with a maximum turning length of 350 mm. The machine includes a robust tool turret with 24 stations and a rapid traverse speed of 20 m/min for X1 and X2 axes. If you are looking to get high-quality turning capabilities, consider the DOOSAN PUMA TT2500SY multi-spindle turning machine. Contact us for further details. • Number of axes: 8 (X1, X2, Z1, Z2, Y, B, C1, C2) • Swing over bed: 800 mm • Swing over saddle: 620 mm • Max. turning diameter: Upper turret 390 mm; Lower turret 300 mm • Recommended turning diameter: 255 mm • Max. turning length: 350 mm • Main/left spindle motor power (30 min / cont): 26 / 22 kW • Main/left spindle nose: ASA A2-8 • Right/sub spindle max. speed: 3500 rpm • Right/sub spindle motor power (30 min / cont): 26 / 22 kW • Right/sub spindle nose: ASA A2-8 • C-axis indexing (C1 & C2): 360° in 0.001° increments • Upper turret travel (X1/Z1/Y): 255 / 800 / 120 mm (±60 mm Y) • Lower turret travel (X2/Z2): 190 / 900 mm • Sub-spindle B-axis travel: 810 mm • Rapid traverse (X1/X2): 20 m/min • Rapid traverse (Z1/Z2/B): 24 m/min • Rapid traverse (Y): 7.5 m/min • Turret stations: 24 total (12 upper + 12 lower) • Tooling type/interface: BMT65P • Indexing time: 0.2 s • Rotary tool spindle speed: 4000 rpm • Rotary tool motor power (15 min / cont): 5.5 / 1.5 kW Dwjdpfx Aoznwf Dokvja • Machine electric power supply: 95.77 kVA Additional equipment • Chip conveyor • Various static tool holders • Rotary live tool holders • Chucks on both spindles Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: ready for operation (used), Year of construction: 1992, spindle speed (max.): 3,600 rpm, bar diameter (max.): 60 mm, total width: 2,000 mm, total height: 1,900 mm, travel distance X-axis: 180 mm, overall weight: 4,300 kg, controller manufacturer: MAZATROL, controller model: T32-2, product length (max.): 2,700 mm, number of axes: 2, Multi-spindle turning machine manufactured in 1992. This Mazak Quick Turn 18 NSP features a maximum turning diameter of 260 mm and a turning length of 500 mm. It includes a tool turret with 8-fold / 16 positions and a spindle speed range of 36 - 3,600 rpm. If you are looking to get high-quality turning capabilities, consider the Mazak Quick Turn 18 NSP machine we have for sale. Contact us for further details regarding this machine. - Control: MAZATROL T32-2- Max. Turning Diameter: 260 mm- Max. Turning Length: 500 mm- Speed Range Main Spindle: 36 - 3,600 rpm- Speed Range Sub-Spindle: 36 - 3,600 rpm- Travel Z-Axis: 510 mm- Travel X-Axis: 180 mm- Spindle Bore: Ø 70 mm- Bar Loader Length: 3,000 mm- Collet Chuck Holder: For 185 E collets- Collet Chuck Range (Main Spindle): Ø 4 - 60 mm- Sub-Spindle: 3-jaw chuck, Ø 125 mm to Ø 70 mm- Tool Turret: 8-fold / 16 positions- Tool Eye: Measuring probe for tool measurement in working area- Main Spindle Chuck: KITAGAWA 3-jaw chuck Ø 254 mm- Coolant System: Complete coolant equipment- Foot Switch: 2 double foot switches for opening/closing both chucks- Machine Weight: 4,300 kg- Machine Dimensions (L x W x H): 2.7 x 2.0 x 1.9 m Optional Dwedozarf Ropfx Akvoa - Drip pan (2500 x 2700 mm), IRCO 3000 mm bar loader Technical Specification Counter Spindle Yes

Condition: used, Year of construction: 2015, The machine will be delivered as shown in the photos, including the visible tool holders, etc. Dwsdpfjzlqavex Akvoa

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, We offer you: Manufacturer: INDEX Type: MS40-6 C Year of construction: 2019 Control: Index control C200-SL, MS40C Double-NCU Technical data: Working spindles: Number: 6 pcs. Spindle bore: max. 40 mm Max. speed: 7,000 rpm Power (100% / 25%): 13 / 24 kW Torque (100% / 25%): 31 / 57 Nm Synchronous spindle: Number: 1 pc. Spindle bore: 40 mm Dwedpfx Aezlutmekvoa Max. speed: 8,000 rpm Power (100% / 25%): 10 / 14 kW Torque (100% / 25%): 16 / 22 Nm Slide travel z: 150 mm Number of tools for back-end machining: 3 pcs. Swiveling range b: 144 ° Tool holder: Number: 12 pcs. Slide travel x: 73 mm Slide travel z: 120 mm Tool holder, cut-off and back-boring slide: Number: 1 pc. Slide travel x: 82 mm Number of tools for back-end machining: 3 pcs. Electrical connection data: Rated power: 85 kW Connection power: 101 kVA Rated current: 145 A Max. pre-fuse: 160 A Note: Mains voltage: 400V Note: Electrical frequency 50 Hz Technical features & accessories: - Double-NCU - Signal light 'Smartlight' with LED - Machine designed for connection to a TN network. - Coolant: Cutting oil - NC option Synchronous spindle / Multi-sided turning incl. electronic shaft - INDEX loading magazine MBL40-6/3300/Strip loader/50Hz: - Strip loader 50Hz - for bar diameter D13 - D40 - Bar length 3300 mm - with pilot drilling unit - Material storage with 700 mm support area - Profibus-DP-Master interface. - 1 set (6 pieces) reducing sleeves manufactured for bar or corner dimensions, diameter D = * mm, Inner diameter range D14 - D41 - 1 set (6 pieces) material sliders for material diameter D24mm - D32mm, consisting of: - 6 material sliders D23 - 6 rotating sleeves D23 - 1 set (6 pieces) internal clamping sleeves D23mm - for material diameter D24mm - D32mm - pilot drilling diameter D15mm - 1 set (6 pieces) external stops D23mm - for material diameter D24mm - D32mm - pre-machined - 1 set (12 pieces) reducing sleeves for material sliders. The outer diameter of the reducing sleeves corresponds to the material diameter (D13 - D40) - 1 set (6 pieces) adapter sleeves, inner diameter range D13.5 - D40.5. The inner diameter of the adapter sleeves should be bar diameter + 0.5mm. - 1 set (6 pieces) two-part guide intermediate tubes, diameter 29 mm - Assembly aid for the sleeves of the guide intermediate tubes - UNIMAG - Interface for connecting a bar loader - Part discharge via slide into spindle position 6 - Workpiece conveyor belt in spindle position 6, machine-integrated - Hainbuch TOPlus Axfix D40 for synchronous spindle - Multi-sided and thread milling device - Reduction ratio i=5:1 - Inductive encoder for reference query - Internal oil lubrication - INDEX short taper connection - without converter - Back-end machining device on slide position 6.2 for max. three boring positions for fixed tools FURTHER INFORMATION IN THE PICTURES Accessories, tools and clamping devices shown are only included in the scope of delivery if this is stated in the additional information. Changes and errors in the technical data and information, as well as prior sale, are reserved!

Condition: good (used), functionality: fully functional, 2 Index MS 25 E machines in very good condition and fully functional – also available individually – for sale. Dwodpezicxljfx Akvea Inspection while the machines are powered on is possible.

Condition: ready for operation (used), Year of construction: 2015, operating hours: 43,196 h, spindle motor power: 25,000 W, spindle speed (max.): 5,000 rpm, bar diameter (max.): 65 mm, total width: 1,990 mm, total height: 2,300 mm, overall weight: 9,500 kg, controller manufacturer: FANUC, controller model: 310, product length (max.): 4,500 mm, number of axes: 8, This 8-axis DMG MORI Sprint 65 linear was manufactured in 2015. It features a maximum main spindle speed of 5000 rpm and a maximum main spindle bar diameter of 65 mm. The machine includes two turrets, each with 12 driven tool positions, and a robust coolant tank capacity of 650 liters. If you are looking to get high-quality turning capabilities, consider the DMG MORI Sprint 65 linear multi-spindle turning machine we have for sale. Contact us for further details. • Total hours: 64274 h; Operating hours: 43196 h • Counter spindle: 17 kW; max speed 5000 rpm; max bar diameter 45 (65) mm • CNC controlled axes: • X1: stroke 165 mm; rapid 30 m/min; acceleration 5 m/s2 • Z1: stroke 678 mm; rapid 30 m/min; acceleration 5 m/s2 • Y1: stroke 80 (+50/-30) mm; rapid 30 m/min; acceleration 5 m/s2 • X2: stroke 165 mm; rapid 30 m/min; acceleration 5 m/s2 • Z2: stroke 640 mm; rapid 30 m/min; acceleration 5 m/s2 • W2: stroke 690 mm; rapid 30 m/min; acceleration 5 m/s2 Dwedpfx Ajzhkl Dskvoa • Turrets: 2; 12 driven positions per turret; Tool system VDI 30; Max driven tool speed 4000 rpm • Coolant system: tank approx. 650 l; pump capacity per turret 20 l/min; pressure 7 bar • Power supply: 91 kVA • Base machine configuration and functions: • Drive for slide 1 and 2 (all 12 positions) • C-axis for main and counter spindle • Y-axis for slide 1 • Counterspindle collet cleaning with coolant • Mechanical preparation for oil mist filter • Electrical and software interface for bar loader • Angular synchronism between main and counter spindle • Automatic machine shut down • 2 additional on/off outputs (4 M-functions) • Rigid tapping • Piece and time counter • Software for polygonal turning (slide 1 and 2) • Constant cutting speed • Helical interpolation (slide 1) • Spindle speed control • Quadruple warning light • Cooling device for electrical cabinet • Control options: • Tool wear monitoring system (FANUC monitor) • Sister tool selection system (FANUC monitor) Additional equipment • IEMCA MASTER 865 MP 43 L bar feeder • Swarf (chip) conveyor, belt type • Workpiece unloading device including belt • Main spindle collet chuck MPF 65/140 (no axial feed), max Ø 65 mm • Manual collet changer SACO MPT65/140 and MPF65/140 • Counter spindle chuck SMW 175-BBD, incl. adapter • 1 set of soft jaws for SMW 175-BBD • Differential clamping pressure for counter spindle (two selectable pressures) • External flushing of jaws/collets with coolant on main and counter spindle • Various new spare parts available Technical Specification Counter Spindle Yes

Condition: ready for operation (used), Year of construction: 2015, operating hours: 42,222 h, spindle speed (max.): 5,000 rpm, bar diameter (max.): 65 mm, total width: 1,990 mm, total height: 2,300 mm, travel distance X-axis: 165 mm, travel distance Y-axis: 80 mm, overall weight: 9,500 kg, controller manufacturer: FANUC, controller model: 310, product length (max.): 4,500 mm, number of axes: 8, This 8-axis DMG MORI Sprint 65 linear was manufactured in 2015. It features a maximum workpiece diameter of 175 mm and a maximum bar diameter of 65 mm. The machine is equipped with two turrets, each with 12 driven tool positions, and offers a maximum spindle speed of 5000 rpm. If you are looking to get high-quality turning capabilities, consider the DMG MORI Sprint 65 linear multi-spindle turning machine we have for sale. Contact us for further details. Control system: CNC 310 isTotal hours: 61295 hOperating hours: 42222 hMain spindle power 20/25 kWCounter spindle power 17 kWMax. main spindle speed: 5000 rpmMax. counter spindle speed: 5000 rpmMax. main spindle bar diameter: 65 mmMax. counter spindle bar diameter: 45 (65) mmCNC CONTROLLED AXESStroke X1 165 mmRapid speed X1 30 m/minAcceleration X1 5 m/s2Stroke Z1 678 mmRapid speed Z1 30 m/minAcceleration Z1 5 m/s2Stroke Y1 80 (+50/-30) mmRapid speed Y1 30 m/minAcceleration Y1 5 m/s2Stroke X2 165 mmRapid speed X2 30 m/minAcceleration X2 5 m/s2Stroke Z2 640 mmRapid speed Z2 30 m/minAcceleration Z2 5 m/s2Stroke W2 690 mmRapid speed W2 30 m/minAcceleration W2 5 m/s2Number of turrets 2Number of rotating tools each station 12 all driven positionsTool system VDI 30Max driven tool speed 4.000 rpmApprox. coolant tank capacity 650 lCoolant pump acity (per each turret) 20 l/minPump pressure 7 barPower supply 91 kVALxWxH of the machine 4.500x1.990x2.300 mmApprox. machine weight 9.500 kgIEMCA MASTER 865 MP 43 L (4m) bar feederBase machine configuration:- Drive for slide 1 and 2 (all 12 pos.)- C-axis for main and counter spindle- Y-axis for slide 1- Swarf conveyor belt type- Counterspindle collet cleaning with coolant- Workpiece unloading including belt- Mechanical preparation for oil mist filter- Electrical and software interface for bar loader- Angular synchronism between main and counter spindle- Automatic machine shut down- 2 additional on/off outputs (4 M-functions)- Rigid tapping- Piece and time counter- Software for polygonal turning for slide 1 and 2- Constant cutting speed- Helical interpolation for slide 1- Spindle speed control- Quadruple warning light- Cooling device for electrical cabinetAdded options:I-V50011 Collet chuck Type "MPF 65/140" without axial feed for main spindle max. diameter: mping elements and other equipment:I-V50025 Manual collet changer type "SACO MPT65/140 and MPF65/140"I-V50092 Differential pressure for counterspindle, possibility of setting two different clamping pressures.I-V50083 1 set of soft jaws for chuck type "SMW 175-BBD"I-V50080 Chuck type "SMW 175-BBD" For counter spindle, including adapter for adapting the spindleI-V60050 Tool holder for drilling tools with internal cooling and cylindrical shank Ø 32mm,with clamping shank according to DIN 69880 (VDI 30) - 4pcsI-V60010 Radial tool holder for external machining type C1 with clamping shank according to DIN 69880 (VDI 30) - 5pcsControl system options:I-V12060 Tool wear monitoring system Monitor for CNC FANUCI-V12070 Sister tool selection system for Tool Monitor for CNC FANUCHydraulic and filtration equipment:I-V40045 External flushing of jaws/collets with coolant on main spindle and counter spindleSpecial optionsSK001 Special clamping device with mandrel for counter spindle product HAINBUCH AXFIX 811 including 2 colletsVarious new spare parts are included. Technical Specification Dwjdpfx Akjzhklwsvsa Counter Spindle Yes Driven Tools Yes

Condition: excellent (used), Year of construction: 2000, Spindle block Cross-drilling unit Dedjyz Di Sepfx Akvewa Pick-up Threading Iemca PRA bar feeder Spindle bearings recently replaced

Condition: excellent (used), Year of construction: 2007, Schutte SG18 with automatic bar loader IEMCA PRA. Includes numerous books, cams, etc. It is in excellent condition. We never use it in our facility. It was purchased for a project, but the volumes are too low for this excellent machine. Djdpszal Swjfx Akvjwa

Year of construction: 2023, condition: new, MORI-SAY TM 620 CNC lathe with digital slides and its new Cucchi-BLT bar feeder Machining of medium and large series max Ø 20 mm (Ø 24 mm) Interchangeable MORI-SAY 6/20 AC equipment Dwodpokvl Eyefx Akvoa Double Fanuc control with touch screen Up to 34 numerically controlled axes

Year of construction: 2023, condition: new, Number of spindle: 6 Max bar diameter: 32/42 mm Max. length of feeding: 125 mm Spindle speed: max 4.250 rpm This machine is perfect for the fabrication of medium and mass component productions until 42 mm diameter and 47 mm with integrated bar loader. ther solution, it can be equiped in second operation machine by loading rough component to finish with a maximum of 130 mm capacity. Options : Machine can receive 7 CNC axis maximum, adding 840D Siemens control, station on demand Djdpfokvnu Hjx Akvewa

Condition: new, MANURHIN K'MX 620 is designed for the productive machining of workpieces consisting of bars with a maximum diameter of 20 mm. The machine is equipped as standard with two electro-spindles with a maximum speed of 12,000 rpm and a rotating guide bush synchronised with the main spindle by means of pulleys and belts. Main features: - Max. bar material diameter 20 mm - 12,000 rpm on both spindles - Main spindle power 3.7/5.5 kW Dsdpfx Aeuqngqskvswa - Spindle travel 210 mm - Number of tools in the cut at the same time: 2 - Power of rotating tools: 2kW - Number of stations: 22, 9 of which can be motorised

Condition: excellent (used), Year of construction: 1995, - Pneumatic pick-up - Pick-up brake - Axial control station 5 Djdpfjuq A Aysx Akvewa - Oscillating pick-up arm passage 25 - 1 tool breakage detector - Bar drop cylinder - Siemens OP5 panel - IEMCA PRA 40/42P bar loader

Condition: excellent (used), MORI-SAY 6/32 rebuilt in standard configuration with : Djdpfx Akjmhfxmovswa - 4 composite slides at stations 1-2-4-5 with independent movement - SIEMENS model S5 Simodrive motors for feed speed conditions Chip conveyor : Removable tank with chip conveyor Pick-up : Synchro pick-up Pick-up brake Hydraulic slide for rear machining Other accessories and special accessories on request

Condition: excellent (used), Year of construction: 1993, - Gildemeister original pneumatic pick-up - Oscillating arm of resumption passage 25 Dwedpfekwcx Ssx Akvoa - 1 detector for drill bit breakage - Bar drop exclusion cylinder - Balluff BMC 8 - Bar loader IEMCA PRA 52/31 P

Condition: excellent (used), - Chip conveyor with extractable tray - 4 cross slides pos 1,2,5,6 - AC motors for spindle speeds and feeds - New Siemens electrical cabinet Djdpsq Tq Imjfx Akvowa - Siemens PLC 7.300 control panel - Machine with hydraulic pick-up and hydraulic cross slide - Tool holders and equipment on request Jfghuc9 Cycle time studies and part set-up on request.

Year of construction: 2016, condition: excellent (used), MORI-SAY TMZ 8/67, year 2016, like new, only 1 year and half production. – Cucchi-BLT bar-loader Bundle for 5 m bar long with 52 mm bar capacity Machine with : – Hirth coupling – Collets Hainbuch BZISK80 – Siemens SINUMERIK SOLUTION LINE 840 SL for driving 8 spindle with C axis 8 CN frontal slides 8 CN cross slides : stations 1, 2, 3, 4, 7, XZ axis stations 5, 6, Y axis with 3 fixed stations 8, U axis part-off or driven toolholders stations 8, Y axis for back burring with 3 fixed 3 driven toolholders – Swarf conveyor with magnetic drum – Arm part catcher Dedpfxoir Ikds Akvjwa – Belt parts conveyor – Kraft and Bauer fire system – Losma HP Pump 70 bars, 100 L/min – Chiller green Box – UAS Fume extractor Machine in good condition like new, please ask for more informations.

Condition: new, Number of spindle: 6 Max bar diameter: 20 mm Max supply length: 100 mm Spindle speed: max 6.000 rpm Dodpfskvl Erox Akvowa Multispindle cam machine for small bar capacity with high rigidity, high accuracy and very fast. This rigid and highly accurate machine is very fast. This machine is used for medium and mass component productions from bar material or rough part not finish with special bar loading. Machine is equiped with thruth coupling, 6 longitudinal slides, 6 cross slides wtih station 1 ; 2 ; 4 ; 5 with long turning. AC speed and feed adjustable, machines can be equiped with automatic bar loader.

Condition: new, Year of construction: 2023, Number of spindle: 6 Max bar diameter: 32/42 mm Max. feeding length: 150 mm Spindle speed: max 5.000 rpm This machine combines the high productivity and robustness of the cam-operated multi-spindle with the advantages of numerical control, which has been made easy for the operators to use. The machine is equipped with a Siemens 840D Solution line dual NC for the control of 24 basic axes and 20 additional axes as an option. Dwsdpfxskvnvve Akvja The 6 independent spindles with AC motors have a power of 7 kW allowing the machining of difficult materials.

Condition: used, Year of construction: 2006, Used INDEX MS 32 C lathe Equipment: -2 NCU -SIR MS32P with shelves, length 3300 mm, screwed rails -Counter spindle -KNOLL complete with 1 HP pump -Bar stop control -Programmable inputs/outputs -4 tool breakage checks -1 NCU1 and 3 NCU2 rotary tool drives -1 WTO stroke doubler, 3 positions, motorized on station 1 -2 drilling units with 6044 motor sold with the machine. -Transmit Dwodpsxgh Elefx Akvsa Equipment listed below with : CNC axis: 1.1 XZ 1.2 Z 2.1 Z 2.2 XZ 3.1 XZ 3.2 XZ 4.1 XZ 4.2 XZ 5.1 XZ 5.2 XZ 6.1 XZ 6.2 XZ