Used Turn Cross for sale (11,839)

Year of construction: 2015, condition: excellent (used), functionality: fully functional, Technical specifications for the bale opening line for RDF, MSW, paper, and cardboard: Manufacturer: Cross Wrap Oy Ltd., Siilinjärvi, Finland Type: BO 4000 Year of construction: 2015 Number of bales opened: 674 Operating time: only 3 days, exclusively during the initial commissioning of the entire system upon new installation Opening time: approximately 45 seconds per bale Bale dimensions (W x H x L): 1100 x 1100 x 1400 – 1900 mm Max. bale weight: 2,000 kg System conveying height: 1,400 mm Max. system conveying width: 1,200 mm Material to be opened: RDF/MSW System availability: 98% Noise level of the bale opening line: 85 dB(A) Total connected load: 37 kW Rated current: 125 A Control panel: SIEMENS SIMATIC HMI Touch Controller: SIEMENS S7 ET200S Installation dimensions: 8,463 x 2,890 x 3,960 mm (L x W x H) Scope of supply: Fjdszp H R Eopfx Albegg Infeed conveyor: 3,500 x 1,200 x 1,400 mm Feed conveyor to the opener: 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in the hydraulic oil tank Control cabinet heating Oil cooler for hydraulic unit Explanation for the short operating time: The entire Cross Wrap bale opening line, type BO 4000, was installed in 2015 at a municipal waste incineration plant. The reason for installing the system was to ensure that municipal waste could continue to be accepted, compressed, wrapped, and stored even during an operational disruption or maintenance of the incineration plant until the disruption was resolved. Subsequently, all the bales were to be opened again, and the waste fed into the normal incineration process. This worst-case scenario never occurred. The system was installed, commissioned, and then never used in normal operation. Only during the commissioning and initial operation of the entire system in 2015 were 674 bales opened over three days. The system is in very good condition and is immediately ready for operation. Due to restructuring measures in the incineration plant, the installation space of the bale opener was needed. This means that the complete line is now available for sale. Brief description of the bale opening process: The compressed bales are placed on the infeed conveyor from the side or from the rear using a forklift. To open the bales, they must be positioned horizontally to the conveyor with the wire or twine binding; otherwise, the bales must be rotated by 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or the twine binding. The rotating knife cuts the bale lengthwise. After that, the gripper returns to its starting position. The opened bale is now conveyed via the conveyor to the discharge chute and then falls onto the subsequent conveyor system. Remarks: New price of the complete system: €296,000. The documentation (operating manual, CE declaration, electrical/hydraulic circuit diagram) is complete. The system has been dismantled into transportable units, stored, and is available for inspection and loading in the short term. We assume no liability for the technical data or any potential errors.

Condition: good (used), Year of construction: 2006, Machine used only for plastic. Technical details shown in attached pdf document. Parts shown by hand not come. Fsdpfx Aleu Ibihsbjgg

Condition: good (used), Year of construction: 2016, FOR SALE CNC Lathe TOP TURN S20C – Year 2016 Brand: TOP TURN (Distributed by major machine tool networks) Model: S20C Year: 2016 CNC Control: FAGOR (User-friendly interface for teaching cycles and ISO programming) Technical Description This 2016 CNC lathe is a versatile machine, ideal for precision work in small to medium production batches. Its modern design offers excellent rigidity and very quick set-up, thanks to the Fagor control system. Capacity: - Swing over bed: 400 mm - Swing over carriage: 210 mm - Distance between centers: 1,000 mm - Bed width: 300 mm Spindle: - Spindle bore: 52 mm (Comfortable bar capacity) - Spindle speed: Up to 2,500 rpm - Spindle nose: Camlock D1-6 Included Equipment - FAGOR CNC: Color screen, cycle-assisted programming (ideal for operators used to conventional machines) - Turret: Automatic turret (electric/hydraulic) for fast and programmable tool changes - Chuck: Precision 3-jaw chuck (approx. 200 mm diameter) - Tailstock: CM4, robust - Safety: Fully enclosed machine with interlocked sliding doors, compliant with CE standards Fgjdjy Slttepfx Albjg - Coolant system: Centralized with integrated chip tray Highlights - Recent (2016): Modern electronic and mechanical components, easy to source spare parts - Precision: High-precision ball screws on both axes - Compact: Small footprint relative to its machining capacity Weight and Dimensions - Dimensions: Approx. 2,400 x 1,400 x 1,700 mm - Weight: Approx. 1,800 kg

Condition: like new (used), Range (depending on lighting conditions): up to 15 m Range with laser receiver: 30 m and more Leveling accuracy at 5 m: +/- 1 mm Self-leveling range: 4° +- 0.5° Accuracy of the horizontal line at 5 m: +- 1.5 mm Accuracy of the vertical line at 3 m: +- 0.75 mm Number of laser lines: 2 Weight: 485 g Fgedpod Ecncsfx Albog

Year of construction: 1981, condition: good (used), Spindle motor for CNC lathe MAZAK SLAT TURN 30, year of manufacture 1981. Fgsdpfx Alexr Dhyebog

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Fsdpfx Asfv Hphelbegg Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: used, Year of construction: 2016, machine/vehicle number: 179057920, type of input current: three-phase, input voltage: 400 V, input frequency: 50 Hz, input current: 65 A, No minimum price – guaranteed sale to the highest bidder! The machines are still assembled, but disconnected from the power supply. An 11-ton forklift is available on site for loading. For sale is a vertical turning lathe manufactured by WEISSER, model: Vector C-1R. TECHNICAL DETAILS Fsdszy Ukzepfx Albjgg Year of manufacture: 2016 Three-phase operating voltage: 400 V AC Frequency: 50 Hz Control voltage: 24 V DC Magnet voltage: 24 V DC Rated current of the machine: 65 A Main connection fuse: 100 A, time-delay

Condition: used, Year of construction: 2005, turning length: 705 mm, turning diameter: 356 mm, travel distance X-axis: 260 mm, travel distance Z-axis: 795 mm, controller model: MORI SEIKI MSX-850, TECHNICAL DETAILS Turning diameter: max. 356 mm Standard turning diameter: 275 mm Turning length: max. 705 mm Travel in X-axis: 260 mm Travel in Y-axis: ±50 mm Total travel in Y-axis: approx. 100 mm Fgedpfxozwgwzs Albeg Travel in Z-axis: approx. 795 mm Rapid traverse rate X/Y/Z: 30 m/min Tool stations: 12 MACHINE DETAILS Design: SY with Y-axis Control system: MORI SEIKI MSX-850 Bar feed magazine: LNS Quick Load Servo 2 Bar length: max. approx. 1,500–1,600 mm / 63″ EQUIPMENT Tailstock Driven tools Y-axis LNS Quick Load Servo 2 bar feed magazine

Condition: used, Year of construction: 2006, turning length: 1,298 mm, turning diameter: 356 mm, spindle speed (max.): 4,000 rpm, controller model: MORI SEIKI MSX 850III / MAPPS III, center width: 1,250 mm, TECHNICAL DETAILS Maximum turning diameter: 1,250 mm Maximum turning length: 1,298 mm Maximum turning diameter: 356 mm Standard turning diameter: 275 mm Swinging diameter over bed: 923 mm X-axis travel: 260 mm Z-axis travel: 1,345 mm Maximum spindle speed: 4,000 rpm Spindle bore: approx. 80 mm Number of turrets: 1 Number of tool positions: 12 Fedpfx Aezwgquelbjgg MACHINE DETAILS Control system: MORI SEIKI MSX 850III / MAPPS III Dimensions & Weight Dimensions (L x W x H): 5,000 × 2,300 × 2,400 mm Machine weight: 7,600 kg EQUIPMENT IRCO SIMAG loader magazine Chip conveyor Powered tools C-axis Y-axis

Condition: ready for operation (used), Year of construction: 2012, operating hours: 926 h, functionality: fully functional, machine/vehicle number: 546324, saw blade diameter: 500 mm, cutting width (max.): 300 mm, overall weight: 1,500 kg, saw blade length: 7,209 mm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Max. saw blade length: 7,209 mm Max. saw width: 300 mm Max. saw blade diameter: 500 mm Arbor saw blade diameter: 85 mm Infeed table length: 7,850 mm Outfeed table length: 2,400 mm MACHINE DETAILS Voltage: 400 V Current consumption: 22 A Fuse: 25 A Main motor power: 7.5 kW Connected power: 11 kW Dimensions & Weight Dimensions (L x W x H): 11,250 x 900 x 1,800 mm Weight: 1,500 kg Operating hours: 926 h Fsdpfx Ajzzbfbslbsgg EQUIPMENT CE marking

Condition: ready for operation (used), Year of construction: 2020, operating hours: 7,597 h, functionality: fully functional, machine/vehicle number: NL257200651, turning diameter: 366 mm, spindle speed (max.): 4,000 rpm, controller model: Mitsubishi 730UM CELOS, working length: 700 mm, number of slots in tool magazine: 12, TECHNICAL DETAILS Maximum machining length: approx. 700 mm Maximum turning diameter: 366 mm Workpiece length with tailstock: max. 728 mm Spindle speed: max. 4,000 rpm Tool turret: 12-position BMT60 star turret Tool drive: 40 / 14 Nm Speed of driven tools: max. 10,000 rpm Overhang length of driven tools: 100 mm Chuck: 10" hollow chuck, Ø 254 mm Chuck cylinder: hollow chuck cylinder BB210A821 Tailstock: NC tailstock Tailstock taper: MK 5 MACHINE DETAILS Coolant type: water-miscible coolant / emulsion Coolant pressure: 5 bar Extraction connection: Ø 150 mm Mains voltage: 380 V Frequency: 50 Hz Transformer power: 45 kVA Phases: 3 phases Isolation transformer: 400 V ± 5 % Current: 65 A Control system: Mitsubishi 730UM CELOS User interface: CELOS with ERGOline touch panel Machine operating time: 7,597 h Program runtime: 2,138 h Last maintenance: April 2024 Weight: 5,800 kg Fgodpfxozy Hx Dj Albog EQUIPMENT DMG MORI M730UM control system with CELOS ERGOline touch panel 12-position BMT60 star turret with driven tools 10" hollow chuck, Ø 254 mm Hollow chuck cylinder BB210A821 Double foot switch with protective cover NC tailstock with MK-5 mount Oil-air cooler for circulating spindle coolant Hinged belt chip conveyor High-pressure coolant system, 5 bar Oil mist separator AFS 1100 including interface Manual, swiveling tool pre-setter SCHNEIDER transformer 45 kVA Technology cycle "Alternating Speed" Further technical data can be found in the document attached!

Condition: good (used), Year of construction: 2009, JOHNFORD CNC lathe Type GT-80D-2S Year 2009 CNC Control Fanuc Series 18i-TB Country of origin Taiwan Turret amount of positions 12 Bar passage 165 mm Serial no. TDF9007 Turning Length 2000 mm Turning Diameter Over Bed 1550 mm Spindle Speeds 1000 RPM Swing Diameter Over Bed Slide 1270 mm Longitudinal Travel (Z-Axis) 2000 mm Spindle Diameter In Front Bearing 240 mm Spindle Bore 185 mm Spindle power 37/30 kW Cross Travel 685 mm Fedpfx Aljt E Nauebegg Rapid Travel Speed X-Axis 10 m / min Rapid Travel Speed Z-Axis 12 m / min Turret head 12 positions Machine length 9800 mm Machine width 3695 mm Machine Height 5292 mm Weight of the Machine Ca. 40 t

Condition: excellent (used), Year of construction: 2005, Schaublin 102N-VM-CF high precision Swiss lathe Year: 2005 Fjdpfx Aow N Rh Aslbogg max. admitted diameter over the bed 200 mm max. admitted diameter over the slides 120 mm Height of centers 102 mm Distance between centers 450 mm Bed length 1000 mm Bed height 168 mm Power 4.2 KW Spindle speed 100 - 3000 RPM Spindle W25 Transverse stroke, X axis 100 mm Resolution, X axis (radius) 0,01 mm Longitudinal stroke, Z axis 90 mm Resolution, X axis (radius) 0,01 mm Lead screw - 8 longitudinal feeds - Larger feeds possible when using the thread control for turning Max. cross section of tool shank (Multifix system) 10x10 mm Bar holder (MULTIFIX system) diameter 20 mm Height and side-adjustable tailstock: Internal taper of the sleeve Mk2 Spindle OD 30 mm Spindle stroke 80 mm Coolant tank capacity 23 L Electrical power supply voltage 400 V Overall dimensions: length x depth x height: 1500 x 510 x 1550 mm Accessories / options: - ACU-RITE digital readout unit, 3 axis X-Z-Z1 X resolution 0.001[mm] Z resolution 0.005[mm] Z1 resolution 0.005[mm] - Coolant system - Rear sheetmetal guard - Double Start/Stop pedal and spindle rotation direction inversion - Schaublin W25 collet set - Cast iron chuck W25 Ø110[mm] with jaws - Quick-change toolholder turret MULTIFIX-A with holders - Driving system for auxiliary equipment with BELT adjustable and swivelling belt-tensioning attachment drive device complete with motor belt Ø6x2’500[mm] - Tailstock - etc... Under power in our warehouse.

Condition: excellent (used), Year of construction: 2006, functionality: fully functional, CNC Control MSX-850 Maximum turning diameter: Ø 420 × 720 mm X/Z axis travels: 280 / 820 mm Swing over bed: Ø 995 / Ø 825 mm Fgedpszz Ak Ejfx Albog Maximum bar diameter: Ø 90 mm Rapid traverse X/Z: 30 / 30 m/min Main spindle diameter: Ø 300 mm Main spindle speed: 3,000 rpm Main spindle power: 22 / 18.5 kW Main spindle nose: A2-8 Number of motorized turret positions: 12 Tool speed / power: 6,000 rpm / 5.5 kW

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, CNC control MORI SEIKI MSG-805 MAPPS Maximum turning diameter: Ø 430 mm Maximum turning length: 519 mm X-axis travel: 230 mm Z-axis travel: 520 mm Main spindle speed: 50–6,000 rpm Main spindle power: 15 / 11 kW Main spindle bore diameter: Ø 56 mm Maximum bar diameter: Ø 45 mm Sub-spindle speed: 5,000 rpm Turret positions: 12 Powered tool speed: 3,000 rpm Fgedpfjzz Agyjx Albog

Condition: used, Year of construction: 2004, Technical details turning diameter 210 mm turning length 700 mm control Okuma OSP-E 100 L total power requirement 35,7 kVA weight of the machine ca. 7,1 t dimensions of the machine ca. 2660 x 2000 x 2330* mm Additional information CNC turning and milling center with C-axis and Y-axis, 2 turrets, and subspindle. The machine is being sold partially overhauled. CNC control: Okuma OSP-E 100 L Maximum turning diameter: 210 mm Swing over bed: 400 mm Distance between spindle noses: 960 mm Main spindle: Spindle bore: 53 mm Speed range: 50 to 6000 rpm Motor power: 11/7.5 kW Subspindle: Spindle nose: JIS A2-6 Speed range: 38 to 5000 rpm Motor power: 11/7.5 kW Z-axis: Travel: 700 / 700 mm (ZA + ZB) Rapid traverse: 40000 mm/min W-axis: Travel: 940 mm Rapid traverse: 40000 mm/min X-axis: Travel: 167 / 192 mm (XA + XB) Rapid traverse: 30000 mm/min Y-axis: Travel: 92 mm (+50/-42 mm) Rapid traverse: 15000 mm/min C-axis: Indexing: 360 x 0.001 deg. Rapid traverse: 400 rpm Disc turret: 2 x 12 stations Tool holder mount: VDI 30 mm Power of driven tools: 4 kW Total connected load: 35.7 kVA Machine weight: 7100 kg Fedpfx Aozzwmujlbjgg Machine dimensions: 2660 x 2000 x 2330 mm* Plus swarf conveyor and bar loader Accessories FMB Turbo 5-42/6200/A bar loader, year of manufacture 2005 Chip conveyor Coolant system Collet chuck for main and subspindle Both turrets equipped with tool holders Machine documentation.

Condition: used, Year of construction: 2007, Technical details: swing diameter: 400 mm turning height: 950-1500 mm Turning length: 210 mm Fjdpfszzvx Aex Albsgg x-travel: 310 mm z-travel: 350 mm spindle turning speed range: 20-3500 U/min weight of the machine ca.: 11 t dimensions of the machine ca.: 4,5 x 3,5 x 2,7 m

Condition: used, Year of construction: 2007, Technical details: Fgsdpfx Alszzvxvjbjg swing diameter: 400 mm turning height: 950-1500 mm Turning length: 210 mm x-travel: 310 mm z-travel: 350 mm spindle turning speed range: 20-3500 U/min weight of the machine ca.: 11 t dimensions of the machine ca.: 4,5 x 3,5 x 2,7 m

Condition: used, table length 605 mm table width 250 mm weight ca. 40.0 kg Current list price: approx. 3.000 euros Special price available upon request Features - Sturdy / solid cross table - From an ALZMETALL column drill press - Machined clamping surface: 605 x 250 mm - Maximum travel: 600 mm Fsdpfx Aezzrf Eolbegg - Adjustment range: 0.05 mm

Condition: used, Year of construction: 2019, bar material dia. 32/38 mm spindle passage 44 mm turning length 320 mm turning speeds 200-8000 U/min c-axis 0,001 Grad gripping station 32/38 mm turning length 120 mm turning speeds 200-8000 U/min c-axis 0,001 0 number of tools 13 fix number of milling stations 4+5 driven control Mitsubishi Meldas M70 Number of axles 5+2 St. total power requirement 7,5 kW weight of the machine ca. 2850 kg dimensions of the machine ca. 2,5 x 1,4 x 1,75 + FMB m CNC sliding headstock machine Citizen L32-1M8, built 01/2019 with barloader FMB turbo 3-36 equipped with swarf & coolant tank, fire distiguisher. ON/OFF 29.564h (status 24.03.2026) Running hours 26.607h (status 24.03.2026) Fjdjy Hl Hiepfx Albsgg GBL function (standard) LFV function: no

Condition: good (used), Year of construction: 2015, Parts shown by hand not come. Fjdpfxszzqnxo Albsgg Upper turret have problems. Dont work.

Condition: used, Year of construction: 2009, Welding rotator, welding turning device Manufacturer: Stierli Type: Rotator 1000 Year of manufacture: 2009 Maximum turning diameter: Insertion width: 1,000 mm Fgsdpfxezkvfue Albjg Load capacity (per pair of rotators): 12 tons Weight: 3,200 kg Stand distance: Standard: 15 meters (connected via a connecting cable), however, the distance can be freely selected, as the stands are mobile. ä9926

Condition: used, mesh wire belt left hand turn all stainless steel belt width 900 mm Fgjdpfx Aozzlrfolbeg adjustable speed

Condition: used, 180° stainless steel wire belt belt width ± 1.000 mm left hand turn all stainless steel mobile 0,18 kW dimensions : ± 3.750 x 2.100 x 1.300 mm Fodjzzk U Ejpfx Albegg

Condition: used, mesh wire belt Fgodpfszzk D Hjx Albsg left hand turn all stainless steel belt width 600 mm adjustable speed dimensions: (l x w x h) : ± 2.000 x 1.000 x 1.100 mm mobile