Used Cross Grace for sale (4,640)

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Pgodpou Tg I Dsfx Ah Heg Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: used, Type: 25 x 120 Straight Bed Lathe Distance between centers: 72″ Swing over bed: 26″ Swing over cross-slide: 16″ Spindle speeds: 7.4 to 600 (24) Spindle bore: 4 1/8 Full length screw cutting: yes Chuck mounting: D1-11 Tailstock taper: No.5 Morse Power compound Power traverse Slide along chuck guard and we have rear splash guarding Main motor: 15kw 3 phase Weight: approx 5 tons Condition: Slideways very good Pgsdpfx Ahowmlcko Heg Can also be repainted at extra cost Cleaned and serviced

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Podpfx Asfv Hphoh Hjgg Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Accuracy of vertical line at 3 m +-0.75 mm Psded Ecncspfx Ah Hsgg Number of laser lines: 2 Weight: 485 g

Condition: used, Roller conveyor with chain cross conveyor Can be used after resaw. - Electric motor: 1,1 kW - Electric motor: 0,75 kW Pedpfei Sdk Sjx Ah Hegg - Electric motor: 1,1 kW

Condition: ready for operation (used), Year of construction: 2002, functionality: fully functional, machine/vehicle number: 388, saw blade diameter: 550 mm, cutting width (max.): 300 mm, power: 6 kW (8.16 HP), total length: 1,800 mm, total width: 1,800 mm, TECHNICAL DETAILS Max. saw blade length: 9,500 mm Max. cutting width: 300 mm Max. saw blade diameter: 550 mm Shaft saw blade diameter: 30 mm Infeed table length: 9,000 mm Outfeed table length: 3,650 mm Pjdpfxoydvphs Ah Hogg MACHINE DETAILS Voltage: 400 V Main motor power: 6.0 kW Power: 6.0 kW Dimensions (L x W x H): 1,800 x 1,800 x 1,900 mm Transport packages: 4 pcs. EQUIPMENT CE marking

Condition: used, Year of construction: 2001, Wood dimensions to be processed: Input lengths min/max 500 - 6500 mm Full optimization up to max. 1500 mm Input widths min/max 40 - 300 mm Input thicknesses min/max 15 - 120 mm Wood cross-sections max. 300 x 40 mm max. 200 x 120 mm Fixed lengths after sawing min. 510 - 2800 mm Special application: Cutting blocks, length min/max. 100 - 200 mm (Caution: Multiple block lengths at the sorting line; blocks are transported to the end of the sorting line and fall into the customer's grid box). Cutting/cutting tolerance +/- 0.8 - 1.5 mm (for wood types with minimal resin content and an even surface. Tolerance up to 1 m fixed length, max. tolerance for longer pieces up to 2.5 m). Thickness tolerance +/- 3 mm. Curvature of the wood in all directions: max. 10 mm per meter in length. Wood types: soft or hardwood. System performance: Feed speed, continuously adjustable up to max. 230 m/cutting cycle 0.6 - 1. To obtain the practical output per day, an effectiveness factor dependent on the customer's production conditions must be calculated. Infeed and saw height: 900 mm (placed on customer's platform, saw requires concrete base). Sorting working height. 2000 mm Connection values: Total electrical connection value approx. 18 kW Operating voltage 380 Volt / 50 Hz Voltage fluctuations max. 5% Air consumption approx. 1200 NL/operating pressure approx. 8 bar Extraction speed approx. 30 m/nd Color pebble gray RAL 7032 and blue NCS 5030-R 80 B POSITION OVERVIEW: Item 1 Infeed and marking station with 1 side support table, adjustable 1 table as stop edge Item 2 Support roller without drive, front side in front of sheet metal table for easier feeding Item 3 Length measuring station with built-in fluorescence camera for detecting error markings Item 4 Automatic width measurement, contactless Item 5 OptiCut 304 optimizing cross-cut saw - right-hand version with built-in waste chute including equipment package for large wood cross-sections Graphic input terminal (16 x 40 characters, Numeric keypad) with software package for optimization and system control. Available for processing: - max. 16 product groups - max. 8 grades per product group - max. 200 fixed lengths per product group Item 6: Outfeed conveyor as sorting station with drive unit, length 7500 m Item 7: 2 ejectors mounted on the outfeed conveyor Podpjw Sy T Hofx Ah Hegg Storage location: Nattheim

Condition: good (used), Year of construction: 2009, with Heidenhain iTNC 530 control 18-speed milling gearbox Clamping area 560 x 1600 mm 7 clamping slots Top width of T-slots 18 mm Distance between T-slots 80 mm Infinitely variable feed longitudinal/transverse 10 - 5000 mm/min Vertical feed 10 - 2500 mm/min Adjustable via Overdrive from 0 to 150 % Rapid traverse longitudinal/transverse 10 m/min Rapid traverse vertical 4 m/min Podpfx Aoydlc Dsh Hegg Operating voltage 400 V / 50 Hz CE conformity declaration available!

Condition: used, Year of construction: 2001, Abrasive belt length 1st unit: 2,150 mm Max. working width: 1,300 mm Number of belts: 3 Belt 1st unit: cross belt Design 1st unit: cross belt Sanding pad 1st unit: electronic segmented pad Abrasive belt width 1st unit: 150 x 4,800 mm Drive 1st unit: kW 2nd unit: longitudinal roller Design 2nd unit: steel calibration roller Abrasive belt length 2nd unit: 2,150 mm Abrasive belt width 2nd unit: 1,350 mm Pgedjxzi S Nspfx Ah Hjg Abrasive belt speed 2nd unit: 18 m/sec 3rd unit: pad unit Design 3rd roller: electronic segmented pressure beam SDS system Sanding pad 3rd unit: electronic segmented, 32 mm width Abrasive belt length 3rd unit: 2,150 mm Abrasive belt width 3rd unit: 1,350 mm Suitable for lacquer sanding: yes Belt air blast: yes Vacuum conveyor: yes Feed speed, fixed: stepless 5 – 15 m/min Control: screen control Electrical/pneumatic belt oscillation: electrical Infeed height: variable (lower table moves) Table height adjustment: electric motor Table height display: digital Working height / feed table height: 880 mm Location: Supplier

Condition: excellent (used), Catalogue No.: 7858 ADVANTAGES – Polish production – for cross-cutting packages or round timber – unpainted – mobile, on wheels – used saw, in very good condition Pgsdpfx Ahsx I Edqo Hsg TECHNICAL DATA guide bar length: 2100 mm cutting length: 1900 mm automatic lubrication of the cutting system damping and tension system in the head manual guide bar feed electric motor: 7.5 kW transport dimensions (L/W/H): 1900x900x2710 mm total weight: 205 kg Net price: 28,900 PLN Net price: 6,880 EUR (based on exchange rate 4.2 EUR) (Prices may change in the event of significant fluctuations)

Condition: excellent (used), Double mitre saw OMS INVINCIBLE OK 330 Maximum cutting length: 3000 mm Maximum cutting width: 140 mm Units adjustable to an angle of 45/-45° Motor power: 2×2.2 kW Pgsdpfxeydc Tmo Ah Hsg Saw blades: 330 mm Pneumatic vertical material clamp

Condition: used, Year of construction: 2002, total height: 1,600 mm, total length: 9,000 mm, total width: 2,400 mm, Weight: 2.500 kg Price: On request - Year: 2002 Pgedpoyddkasfx Ah Heg - Documentation available: No - CE certificate present: No - Serial number: 1073.14 - Input table length [mm]: 8360 - Output table length [mm]: 2750 - Options: Automatic pusher system - Voltage [V]: 400 - Fuse [A]: 25 - Power [kW]: 11.0 - Transport dimensions: 9000mm x 2400mm x 1600mm (l x w x h) - Transport weight [kg]: 2500kg - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: like new (used), Year of construction: 2008, AGRICULTURAL MACHINERY BUCHER CROSS-FLOW-FILTER FM 20 Pgjdpfjgy T Dzex Ah Hog

Condition: excellent (used), functionality: fully functional, Cross-cut multi-blade saw for the production of squared timber and turning blanks Pgsdpfoych N Dsx Ah Hog

Condition: used, Year of construction: 2018, functionality: fully functional, machine/vehicle number: 351.09.006.18, Subscrisa, DDG INSOLVENCY I.P.U.R.L., cu sediul în Cluj-Napoca, str. Septimiu Albini, nr. 115, jud. Cluj, CIF RO27987796, nr. matricol: 2A0522, prin practician în insolvență Godorogea Daniel-Lucian în calitate de lichidator judiciar al societății ELEMENTO MOBILI S.R.L. - în faliment, in bankruptcy, en faillite, cu sediul social în mun. Dej, str. Dumbrava Roșie, nr. 6, et. parter, ap. 1, jud. Cluj, înregistrată la Registrul Comerțului de pe lângă Tribunalul Cluj, sub nr. J12/2389/2016, cod unic de înregistrare 36225390 desemnat în această calitate prin Încheierea Civilă nr. 1278 din data de 03.07.2025 pronunțată de Tribunalul Specializat Cluj în dosar nr. 442/1285/2025, organizează licitație publică cu strigare, cu preț în urcare, pentru vânzarea individuală a bunurilor identificate în prezentul anunț Prima licitație va avea loc la data de 11.02.2026 la ora 15:00, la sediul DDG Insolvency I.P.U.R.L. din Cluj-Napoca, str. Septimiu Albini, nr. 115, jud. Cluj. În caz de neadjudecare licitația se repetă în data de 18.02.2026, 25.02.2026, 04.03.2026, 11.03.2026, 18.03.2026, în aceleași condiții și la aceeași oră. În vederea vizionării bunurilor, lichidatorul judiciar va stabili o zi de vizionare în data de 04.02.2026 între orele 10:00-14:00. Cei interesați de vizionare sunt invitați să contacteze lichidatorul judiciar la și să își exprime intenția de participare, anterior datei stabilite. În caz de adjudecare, lichidatorul judiciar va emite factura fiscală pentru contravaloarea bunurilor adjudecate. Conversia prețului în lei se va realiza la data emiterii facturii fiscale, utilizând cursul de schimb stabilit de BNR pentru acea dată. Pasul de licitație este de 5% din prețul de pornire. Caietul de sarcini în vederea participării la licitație va fi întocmit de către lichidatorul judiciar în concordanță cu uzanțele în materie, va conține regulamentul de participare la licitație și se va valorifica de către practicianul în insolvență, la prețul de la prețul de 500 lei+TVA pentru bunurile de până la 5.000 euro și de 1.000 lei+TVA. pentru bunurile de peste 5.000 euro. Acesta poate fi achiziționat de la sediul lichidatorului judiciar, sau telefonic urmând a fi transmis participantului prin e-mail. Garanția de participare la licitație va fi în cuantum de 10% din prețul de pornire. Aceasta împreună cu documentația de înscriere la licitație vor trebui depuse cu cel puțin 24 de ore anterior datei licitației la sediul lichidatorului judiciar. Garanția de participare la licitație va fi dedusă din prețul bunurilor pentru care participantul a fost declarat adjudecatar și va fi restituită persoanelor care nu au fost declarate adjudecatari. Pjdpfx Aoyfg E Nsh Hsgg La preț egal, va fi declarat adjudecatar persoana care se va angaja să achite întregul preț în termenul cel mai scurt. Termenul de plată al prețului va fi de 5 zile lucrătoare de la momentul adjudecării. În cazul în care nu se va achita și restul de preț, adjudecatarul va pierde avansul achitat cu titlu de garanție și nu va mai putea participa la următoarele licitații care se vor organiza.

Condition: used, Format: 310 x 432mm Equipment: roller adjustment: fully automatic model: flat pile feeder with air-suction type of fold: single fold, parallel fold, short fold, letter fold, according fold, gate fold sheet size: max. 310x432mm; min. 125x130mm paper weight: 50-190g/sqm pile height: 50mm speed: max. 240 sheets/min. power: 230V/50Hz - 0,6kW dimensions: 1.060x553x670mm weight: 45kg Pedpjx N I Uhjfx Ah Hegg

Condition: used, Year of construction: 2005, total height: 1,750 mm, total length: 1,350 mm, total width: 1,350 mm, Optimization cross-cut saw Stromab TR 500 Matrix 4 4000 Year of construction 2005 Engine power 10 hp Auto push-up system Inkjet printer - Year: 2005 - Documentation available: No - CE certificate present: No - Serial number: 250143 - Main motor power [kW]: 7.5 - Max. saw width [mm]: 375 - Arbor saw blade diameter [mm]: 30 - Input table length [mm]: 4300 - Output table length [mm]: 2000 - Transport dimensions: 1350mm x 1350mm x 1750mm (l x w x h) - Transport packages [pcs.]: 3 Pgodpswq U Dxofx Ah Hog Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: refurbished (used), C11 MKL Cross-Cut Optimization Line, offered by Wood Expert Industry, is a state-of-the-art technological solution designed specifically for industrial wood processing and operational workflow optimization in woodworking facilities. All equipment comprising the processing line is manufactured by Paul Germany and was completely overhauled in July 2025 with zero operating hours. Paul C11 MKL Lumber Optimization Line Components - 9.0 m / 230 mm Inclined Conveyor Belt Ideal for the automatic and efficient handling of wood pieces towards the processing area, equipped with a guided belt and robust clamping parts for stable transport. - Measuring Station with Luminescent Scanner and Photocell Allows precise identification of the start and end of workpieces, featuring dedicated lower rollers for high-accuracy measurements. - Pressure Roller Unit Ensures correct alignment and pressing of pieces between 250 and 4200 mm, with manual adjustment available according to the material thickness. - Reinforced Marking Rails, Left and Right Automatically pre-marks cutting positions for increased efficiency and accuracy in subsequent processing. - C11 MKL Optimizer – CNC Cross-Cut Saw Station Includes a robust welded steel frame, 500 mm TCT blade, 5.5 kW servo-driven motor, variable speed, and an advanced feeding system with lower/upper rollers for precise piece guidance. Electric adjustment of the upper rollers allows automatic adaptation to wood thickness. The system features automatic waste extraction, extraction ports, CE safety compliance, and advanced cutting quality options (blade with 132 conical teeth). - Waste Extraction System Comprises an 11.5 m / 230 mm conveyor belt and ascending waste belt (3.0 m / 500 mm with collection hopper), optimizing material flow and disposal of residues. - Length Sorting System With pneumatic ejectors and basic sorting equipment, this facilitates automatic organization and discharge of pieces to two outfeed positions, increasing line productivity. - Maxi8 Premium Operator Terminal and Optimization Software 17” touchscreen terminal, dust-protected, remote diagnostics, Linux-based, with dedicated optimization software (up to 60 cutting lists, 9 grading options, 400 preset lengths/list), advanced statistics, network integration capability. Includes data import/export options via USB. Pgjdpfx Ahow Emf Rj Hog - Control and Automation Equipment Standardized electric cabinets, control panels, complete installation and wiring performed with high-quality components for intensive industrial use. Benefits of integrating this line: - Fully automated cross-cutting process, significantly reducing human error. - Increased efficiency and yield through cutting list optimization and automatic length sorting. - Adaptability to various thicknesses and sizes of workpieces. - Advanced digital control and remote diagnostics for quick interventions. - High reliability, reduced maintenance costs, and adherence to strict CE safety standards. This optimization line can be customized for different types of wood processing facilities, ensuring efficient operation tailored to every client’s requirements.

Year of construction: 1994, condition: used, machine/vehicle number: 41094/30, Technical data: - Manufacturer: Cefla with cross axle - Type: TN/L - Length: 1.750 mm - Belt width: 1.400 mm - Total width: 1.600 mm - Height: 950 mm - Year of manufacture: 1994 - Feed rate approx. 2 - 8 m/min. - FU control for feed rate 50 Hz - Frequency converter required on site - Location: in stock - Volts, Hz 400 / 50 - Motor power 0.75 kW - Voltage fluctuations max. +/- 5% Podpfxeya H Hij Ah Hsgg - Location: in stock

Condition: excellent (used), Catalogue number 7837 TECHNICAL DATA - Max. blade diameter: 450mm - Spindle diameter: 30mm - Top pneumatic hold-down - Blade guard - Blade guard also functions as a hold-down - Pneumatic blade stroke - Cutting height: 125x125mm, 100x250mm - Cutting capacity (thickness x width): 50x530mm, 100x480mm, 150x380mm, 200x200mm - Main motor: 5.6kW - Extraction port diameter: 100mm - Table dimensions (L/W): 660x480mm - Table height from base - 2 roller tables - Infeed roller table with guide: 1500mm - Outfeed roller table with guide and latch: 1500mm - Roller width: 300mm - Working pressure: 8bar - Overall machine dimensions (without roller tables) L/W/H: 940x780x1150mm Psdjx Arhcjpfx Ah Hogg - Weight approx. 450kg ADVANTAGES – German manufacture – DTR documentation – 2 roller tables – Pneumatic blade stroke – Saw used, in perfect condition Net price: 14,900 PLN Net price: 3,550 EUR (based on exchange rate 4.2 EUR) (Prices may change in case of significant exchange rate fluctuations)

Condition: not inspected (used), table width: 450 mm, table length: 630 mm, T-slots 18 mm. Podpfx Aoya Hu Hoh Hsgg

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, saw blade diameter: 500 mm, cutting height (max.): 89 mm, cutting width (max.): 200 mm, Optimizing cross-cut saw PAUL C11 MKL Year of manufacture: 2014 The machine is equipped with a measuring station and 5 ejectors. Technical specifications: Cutting height: 3 - 89 mm Pgjdox H Uaxopfx Ah Heg Width: 30 - 200 mm Minimum workpiece length: 300 mm Saw blade diameter: 500 mm Saw motor power: 5.5 kW

Condition: excellent (used), Year of construction: 1988, I sell the cross veneer guillotine Josting QFS 800. Year 1988 (2pcs. available on stock). Cutting length 800mm. Cutting height 60mm. Pgsdpfxeyc Nilj Ah Hog Very good condition. Available immediately.

Year of construction: 2013, condition: good (used), LINK LABEL ISH 330 Cross Cutter → Year of manufacture: 2013 This machine is designed for precise cross-cutting of both printed and unprinted materials and is particularly well-suited for short production runs, variable cut lengths, and processing transparent substrates. Technical Specifications Unwinding System → Integrated unwind unit → Loop control for stable web tension → Roll end sensor included Maximum Roll Diameter → 550 mm Maximum Web Width → 330 mm Cutting Length → Variable, programmable via touch screen → Skip function included → Intermediate cut programmable from 0.10 mm to 50.00 mm Maximum Speed → Up to 500 cuts per minute Drive and Control Podpfsycv Eysx Ah Hogg → Computer-controlled drive system → Touch screen operation Material Handling → Suitable for transparent materials → Suitable for printed and unprinted materials → Optical sensor for register control Delivery System → Delivery conveyor for shingled output → Pulse separation system for reliable product separation Infeed and Web Control → Pneumatic pressure rollers → Web tension control via integrated vacuum system → Vacuum pump included Electrical and Air Requirements Power Supply → 220 V → 10 A Compressed Air → Minimum 6 bar Dimensions and Weight Overall Dimensions (L x W x H) → 1,980 x 900 x 1,038 mm Machine Weight → Approx. 250 kg Why This Machine? The ISH 330 Cross Cutter stands out with its high cutting precision, flexible length programming, and superior web control. Its optical register system and vacuum-controlled web tension ensure reliable, consistent results even at high speeds and when working with challenging substrates such as transparent films. With its compact footprint and intuitive touch screen operation, it is the ideal choice for efficient finishing in modern label production environments.

Condition: new, Year of construction: 2026, Cross splitting wedge for 16-ton log splitters Podpfx Aheycu T Aj Hsgg Allows logs to be split into 4 parts. It features a universal mounting system compatible with most wood log splitters available on the market. Thanks to its universal mounting design, it fits the majority of commercially available log splitters. Manufacturer: Cormak