Used Thread Gauge for sale (4,399)

Condition: excellent (used), workpiece diameter 10 - 250 mm threading length 900 mm thread pitch 0,3 - 100 mm Hjdpfew Rrhgex Ag Dofr spindle turning speed range 72 / 1700 - 2540 U/min relief of the tap 0,03 - 8 mm clamping length max. 1190 mm max. module 10 workpiece turning speeds 0,4 - 160 U/min total power requirement 13 kW weight of the machine ca. 7,4 t dimensions of the machine ca. 4,5 x 2,0 x 2,1 m Many accessories.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 00049781, workpiece diameter (max.): 50 mm, spindle diameter: 69 mm, spindle speed (max.): 5,000 rpm, stroke length: 130 mm, roll spacing: 255 mm, TECHNICAL DETAILS Contact surface: 180 mm Workpiece diameter: 4 - 50 mm Rolling pressure (infinitely variable): 0-200 kN Feed (infinitely variable): 0-50 mm/s Rolling cycles per minute: 0-86 Rolling spindles Rolling spindle diameter: 69.85 mm Distance between rolling spindles: 125 - 255 mm Spindle mounting length: 160 mm Traverse of the rolling spindle slide: 130 mm Rolling spindle speed: 3000-5000 rpm Rolling tool diameter: 130 - 200 mm Machine bed height: 800 mm Height of rolling spindle above machine bed: 160 mm MACHINE DETAILS Control system: SIEMENS SIMATIC C7 Voltage: 400 V, 50 Hz Dimensions & Weight Machine height: 1,600 mm Hfsdsxbfwzjpfx Ag Djr Weight: 2,400 kg

Condition: good (used), Year of construction: 2008, operating hours: 2,500 h, load capacity: 1,200 kg, lifting height: 1,400 mm, fuel type: electric, mast type: duplex, construction height: 2,100 mm, mileage: 2,500 km, The WIDE-TRACK stacker from the brand is from 2008 and in good condition; Capacity 1,200 kg; Lifts up to a height of 1,400 mm. Clearance height is 2,100 mm. Only 2,500 operating hours; Equipped with stainless steel forks! Outside fork width 88 cm, inside 69 cm; Gel battery is maintenance-free and comes with external charger. Watch the video on YouTube. Hedpfsw Nk Suex Ag Dofr

Condition: good (used), Year of construction: 2008, Precision air measuring mandrels/rings, air measuring device, measuring columns and measuring computers, pneumatic-electric measuring column, measuring device, manual measuring device -Manufacturer: Stotz, manual measuring device air measuring device -Probes/measuring accuracy: see photos -Individual components: see photos -Mains voltage: 3x400 VAC / 50 Hz -Compressed air: 3.0 bar Hfodpfeipapiex Ag Dor -Total dimensions: 2800/800/H2450 mm -Total weight: 702 kg

Condition: used, Thread rolling machine, cold rolling machine, thread rolling machine, profile rolling machine Manufacturer PEE-WEE Type P 24 Q serial no. LC2403099 year of construction 2004 Rolling force max. 24 ton. Tool diameter max. 200 mm Rolling spindle diameter 69,85 mm Tool bore diameter 70 mm (nominal diameter) Tool length, tool length max. 180 mm Workpiece diameter max. 50 mm Rolling spindle speed 22 - 44 - 95 - 190 rpm Motor power hydraulics approx. 3 kW Motor power roller drive 5.5 kW Mains connection 400 Volt, 50 Hz Hedpfx Aeh A S Hteg Dofr - Swivel roller spindle for threaded continuous rollers - Rolling spindle speed in 4 stages via gear changeover - Hydraulic system integrated in the machine bed Space requirement L x W x H 2000 x 1750 x 2550 mm Weight approx. 3 tons good condition Grooving rollers: The thread rolling tools with the same pitch as the workpiece form the thread by penetrating into the workpiece up to the nominal diameter. The thread length is maximum as long as the rolling tools are wide. Continuous rolling: When the thread length is greater than the rolling tool width. Through-feed tools have 3 sections - the infeed, the calibration section and the outfeed. Grooved rollers have no pitch and are swiveled with the pitch angle of the profile to be rolled. Pitch rollers differ from grooved rollers in that they have a pitch in the profile. The sum of the pitch angle and the swivel angle gives the pitch angle in the workpiece.

Condition: ready for operation (used), Five older thread milling machines Mikron are available, 3x Hydraulic Thread Milling Machine Mikron 132.02, 1x Mikron 132-01, 1x Mikron 104-01 and 1x Short Thread Milling Machine Mikron 106.01, an on-site inspection is possible. Hsdpfx Agew Sxyxo Defr

Condition: used, Year of construction: 2015, thread dia. 20 - 80 mm grinding length 3500 mm thread pitch . mm threading lenght min./max. 50/3500 mm centre height 400 mm workpiece length - max. 4000 mm control Siemens 840-Dsl Hsdpfow Ed S Usx Ag Dofr feed speed u-axis 0 - 2500 mm/min feed speed w-axis 0 - 2500 mm/min feed speed b-axis 100 1/min total power requirement 45 kW weight of the machine ca. 24 t dimensions of the machine ca. 10,7 x 4,6 x 2,9 m Thread Grinding Machine / Profile Grinding Machine, suitable for: - the thread grinding of single and multi-start ball screws with gothic profiles and special profiles - Ø 20 to 80 mm with a grinding wheel Ø of 350 to 500 mm - length between the centers up to max. 4000 mm Equipment / Accessories: - grinding spindle: - capacity 14 kW - with a grinding wheel diameter range of 350-500 mm, cutting speeds between 20 and 75 m/s can be set. - grinding wheels: - diameter new 500 mm - diameter worn 350 mm - bore diameter 203.2 mm - shaped diamond roll: - diameter 121.3 mm - radius 0.5 mm - driver flange for workpiece diameter 15-70 mm - driver: - for 10-32 mm drive diameter on the workpiece - for 31-60 mm drive diameter on the workpiece - for 60-105 mm drive diameter on the workpiece

Condition: excellent (used), Thread cutting unit with lead screw Currently, a lead screw with a pitch of 0.8 mm (M5) is installed. Hsdpow N E R Eefx Ag Defr Spindle speed 750 rpm max. stroke: 80 mm With UC-21U controller Very good condition

Condition: used, Year of construction: 2002, functionality: fully functional, machine/vehicle number: M24I/9053, Offer Number: M24I/9053 Machinetype: thread rolling machine - 2 rolls Hjdpfx Agjw Nxnwj Defr Make: BAD DÜBEN Type: PRX 32 E CNC Constr. year: 2002 diameter range: 10-24 mm Forging power: 7-20 to thread length plunge method: 195 mm daylight: 160 mm max. pitch: 3,5 mm roller bore: 80 mm roller width: 235 mm roller length: 195 mm rpm: 40 - 315 Location: Germany

Condition: good (used), Thread cutting machine, pipe thread cutter -for: pipe size max. 2 inches -Cutting jaws: 1" inch -Drive: via 3 gears -Dimensions: 550/360/H240 mm Hsdpfxjb A Iyae Ag Dofr -Weight: 55 kg

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Hfodeuz If Nspfx Ag Djr Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 280 0113 4023, THE MACHINE CAN BE VISITED AT OUR PLANT IN BOLOGNA. Hsdowd Shhopfx Ag Djfr

Condition: new, Year of construction: 2024, functionality: fully functional, type of input current: three-phase, total width: 1,800 mm, total length: 2,000 mm, total height: 1,500 mm, overall weight: 5,000 kg, warranty duration: 12 months, spindle diameter: 80 mm, roll diameter: 240 mm, roll width: 220 mm, thread length: 6,000 mm, workpiece diameter (max.): 120 mm, new machine for immediate delivery Hfsdpfsuafrujx Ag Djr

Condition: good (used), Maximum pressure 25tn • 69 and 85mm axles • Machine in very good condition, completely revised Hfedpfxogqumpo Ag Djr

Condition: used, Year of construction: 1991, workpiece diameter 30 mm threading length 110 mm thread pitch 0,5-2,75 mm/GG Hfsdpfx Aet Hwzcsg Djr total power requirement 4,5 kW weight of the machine ca. 1,7 t dimensions of the machine ca. m

Condition: good (used), thread cutting chuck, thread chuck, tapping chuck, milling tool, thread cutting apparatus -Manufacturer: Lenze ABW, tapping chuck MK3 -Type: GB3 Hfsdpfxovvub Ae Ag Dor -Bore: Ø 24 mm -Dimensions: Ø 80 x 265 mm -Weight: 3.7 kg

Condition: used, Year of construction: 1983, functionality: fully functional, machine/vehicle number: M14L/6106, Offer Number: M14L/6106 Machinetype: thread rolling machine - planetary die Make: SIMA Hfjdswi Tbyepfx Ag Djr Type: RAP11 Constr. year: 1983 diameter range: 6-12 mm shaft length under head: 8-75 mm max. thread length: 75 mm output pieces/min: 1000 Location: In our warehouse

Condition: used, Year of construction: 1986, workpiece diameter 460 mm Hfsdpfxot H Smto Ag Der threading length 900 mm thread pitch 100 mm total power requirement 10 kW weight of the machine ca. 8 t dimensions of the machine ca. m

Condition: good (used), Thread cutting machine, pipe thread cutter -Pipe deburrer: for thread cutting machine -Pipe size: up to inner Ø 58 mm -Dimensions: see photos -Dimensions: 270/250/H75 mm Hsdewyu Hfopfx Ag Dofr -Weight: 2.7 kg

Condition: used, Year of construction: 2011, workpiece diameter 320 mm threading length 570 mm thread pitch 315 mm Hodpjt Hxbdefx Ag Defr total power requirement 17 kW weight of the machine ca. 12 t dimensions of the machine ca. m

Year of construction: 1985, condition: used, workpiece diameter 50 mm threading length 100 mm thread pitch mm Hfjdet Hwn Nepfx Ag Der total power requirement 1 kW weight of the machine ca. 1500 kg dimensions of the machine ca. m

Year of construction: 1985, condition: used, workpiece diameter 25-90 mm threading length 3000 mm Hodjtzdyzjpfx Ag Djfr thread pitch 2-16 mm total power requirement 25 kW weight of the machine ca. 10,5 t dimensions of the machine ca. m

Condition: used, Year of construction: 2001, pressure 0,2-40 t max. workpiece diameter 70 mm threading length 120 mm Control total power requirement 29 kW Hodpfx Aot Hw N Teg Dsfr weight of the machine ca. 9,5 t dimensions of the machine ca. m

Condition: used, Year of construction: 1979, workpiece diameter 320 mm threading length 300 mm thread pitch mm total power requirement 90 kW weight of the machine ca. 12000 kg dimensions of the machine ca. m Thread and worm grinder for steering worms Hfsdpot Hwnpjfx Ag Djr

Condition: used, Year of construction: 1985, thread dia. 254 mm grinding length 350 mm thread pitch 51 mm Control SIEMENS S 8 total power requirement 12 kW weight of the machine ca. 5000 kg dimensions of the machine ca. m B A H M Ü L L E R Automatic Internal Thread Grinding Machine Model IPE 12 i.S. Year 1985 Serial No. 103174 _____ workpiece Ø, max. 300 mm Hodpfx Aet Hw U Asg Djfr workpiece length, approx. 350 mm height of centers (WP spindle/grinding spindle) 300 mm table stroke approx. 450 mm thread diameter ground max. approx. 254 mm thread diameter ground min. approx. 25,4 mm thread length ground in one setting max. 250 mm Lead range, max. 51 mm Lead angle max. 10 ° Total electrical load, approx. 12 kW - 380 V - 50 Hz Weight, approx. 5,000 kg Accessories / Special Features * This is a programme controlled (SIEMENS S 8) internal thread and internal worm grinding machine , suitable for the grinding of ball screw nuts. * All movements are controlled by the SIEMENS programme control * Automatic infeed for grinding depth. * Automatic diamond roll profile dressing device, motorized by hydraulic motor,and device can be swivelled and mechanically adjusted lengthwise. * FISCHER Internal grinding spindle up to 30.000 rpm with oil and air lubrication and with Infinitely variable grinding spindle speeds. • 4-jaws chuck approx.. Ø 250 mm * Separate switch cabinet, separate hydraulic unit, oil drip pan, etc. Condition : Good. Machine can soon be inspected under power. Delivery : Ex stock, as inspected. Payment : Net, after conclusion of contract.