Used Scraper for sale (727)

Condition: used, These Scrape Surface Heat Exchangers can be used on various products for heating process such as Tomato pastes, custards, margarines, oils, mayonnaise, etc. We have fully refurbished these units by changing internal gaskets, rings, sand blasting , paint job, new stainless steel frame , new controls and motor test and service . Technical Details of VOTATOR - Make: A. Johnson & Co London - Year of Refurbishment: 2025 - Quantity: 5 units - Diameter: 6 inches - Metals: Grade 316 Stainless Steel - Usage: Horizontal Votators Specifications: - Chamber Dimensions:6" Diameter Stainless Steel Chamber - Length: 6' - 1 1/2" between end plates - Rotating Centre:4 3/4" Diameter Stainless Steel - Equipped with two PTFE scraper blades - Drive:11 kW Motor Drives - Speed: 1470 rpm (through a V-belt reduction) - Reducer:Giving a shaft speed of approximately 367 RPM. Availability: - Location: In stock - Available: Immediately General Capacity Estimation Formula: For a VOTATOR, the capacity can roughly be estimated using the following formula: [ \text{Capacity} = \text{Chamber Volume} \times \text{Turnover Rate} ] Step 1: Calculate the Chamber Volume The volume of a cylindrical chamber can be calculated as: [ V = \pi \times r^2 \times h ] Where: - ( r ) = radius (half of diameter in inches), - ( h ) = height (length of the chamber in inches). Given: - Diameter = 6 inches, so radius ( r = \frac{6}{2} = 3 ) inches. - Length ( h = 6 \text{ ft} = 72 \text{ inches} ). Calculating the volume: [ V = \pi \times (3)^2 \times 72 \approx \pi \times 9 \times 72 \approx 2036.75 \text{ cubic inches} ] To convert cubic inches to liters (since 1 cubic inch = 0.0163871 liters): [ V \approx 2036.75 \times 0.0163871 \approx 33.39 \text{ liters} ] Duedoygh Egspfx Ac Njn Step 2: Estimate Turnover Rate The turnover rate depends on the speed of the VOTATOR and how many times the contents of the chamber can be processed. Given the shaft speed is approximately 367 RPM, you might assume a turnover rate of about 1 turnover per minute for a basic estimate. Final Capacity Estimate Assuming 1 turnover per minute: [ \text{Capacity} \approx 33.39 \text{ liters/min} ] Conclusion The estimated capacity of each VOTATOR is approximately 33.39 liters per minute Capacity Calculation: - Estimated Capacity: 33.39 liters/minute Convert to Liters per Hour: [ \text{Capacity per hour} = 33.39 , \text{liters/min} \times 60 , \text{min/hour} ] [ \text{Capacity per hour} \approx 2003.4 , \text{liters/hour} ] Conclusion The estimated capacity of each VOTATOR is approximately 2003.4 liters per hour.

Condition: used, Year of construction: 2002, operating hours: 10,500 h, functionality: fully functional, travel distance X-axis: 762 mm, travel distance Y-axis: 460 mm, travel distance Z-axis: 460 mm, controller manufacturer: Okuma, controller model: U100, spindle speed (max.): 8,000 rpm, coolant supply: 12 bar, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Okuma MB46 from 2002 Low operating hours! Machine can be inspected under power. Dujdpfewt Dqaex Ac Non 32 tools BT40 Scraper belt conveyor Internal cooling 8 bar 8,000 rpm 4th axis included

Condition: good (used), Year of construction: 2015, functionality: fully functional, edge thickness (max.): 12 mm, ENGLISH: Heavy duty edgebander OLIMPIC (SCM Group) in rich configuration suitable for custom made and series production. Machine is equipped with aggregates with servomotors (ABS R1+R2mm + thin edge + solidwood). Model: Olimpic K800 TERL Manufacturer: SCM Group Production year: 2015 Duodpfswxt Tbox Ac Non State: good Edgebanded edges: 238.800 meters Main technical parameters: - feeding speed: 12/18 m/min. (including rounding) - panel thickness: 10-60 mm (including rounding) Equipment and configuration of the machine: - control panel with LCD touch screen STARTOUCH - internal lightning of working area - automatic lubrication of the feeding chain - electronic top pressure adjustment - glue pot with quick change of the glue color Working units: - antiadhesiv spray - pre-milling unit (2x DIA cutter) - glue pot with roller "VC/1000" (glue pot with quick-release system) - pressure rollers (4 pcs) with timed intervention - 2 motor end cutting unit "K/SEL" with pneumatic tilting of the blades - radius trimming unit "RI/800" R1mm + thin edges + solid wood (12mm) (3 position pneumatic kit) - 2 motor rounding unit "ROUND K MULTI EDGE" R2mm + thin edge (each motor has: 2 electronic axis with servomotor) - radius edge scrapers "RAS/S 2P" MULTI-EDGE R1+R2mm (each unit has: 2 electronic axis with servomotor) - cleaning spray - glue scrapers "RCA/2C" - brushes"SP/F"

Condition: excellent (used), Year of construction: 2020, functionality: fully functional, SOLD BY THE FIRST AND ONLY OWNER AVAILABLE FROM APRIL 2026!! MACHINE IN OPERATION, TOTAL METER AS OF 2.1.2026: 463,700.00M Element return conveyor included in price! E9001500 Gluing machine One-sided edge bander "STREAM A" CE standards compliant E9001560 One-sided edge closure MODEL STREAM A / 6.0 E8000091 DEVICE FOR INSERTING NARROW ELEMENTS E8000086 NC OS PACKAGE – DEVICE GROUP FOR AUTOMATION MACHINE CONFIGURATION Includes: - OS-2: 2 NC OSI on the entry fence and on the first pre-milling copy unit. - OS-1: 1 NC OSI on edge pressure rollers. E9901008 Pre-installation set for return system E8000094 Flat air table at machine inlet E8000041 POSITIONS FOR EDGEBAND TAPE Automatic edge change, NC-controlled standard NC axis for edge guide system. E8000048 Double gluing system for EVA adhesive and granular POLYURETHANE glue E8000101 QM-705 UNIT for EVA hot melt adhesive E8000051 Additional glue tank for machines with EVA glue PRE-MELT UNIT. For granular glue only E8000107 NITROGEN UNIT FOR PU GLUE E4000286 Glue head and glue pot CC10 preheating and maintenance station E8000038 Adjustable infrared lamp AdIRL-700 E8000314 PRE-MILLING UNIT FI-502, diamond cutter H = 45 mm, included Z = 2+2, 30° E8000032 ADZ-700 ANTI-ADHESION UNIT E4000232 Pair of diamond cutters H = 65 mm, Z = 3+3, 45° E8000225 IT90-S CUTTING UNIT E8000109 Antistatic fluid applicator for finishing rounding unit E8000405 RS-100 UPPER AND LOWER EDGE MILLING UNIT E8000415 PRO-NESTING KIT UPPER AND LOWER EDGE MILLING UNIT E0001597 Pair of flat milling cutters with sliding attachment for upper and lower edge milling unit E8000508 RF400 FINE MILLING UNIT E8000527 PRO-NESTING KIT for fine milling unit E0001639 Pair of multifunction milling blades for fine milling unit. Milling at 25 degrees – R = 1 / 1.5 / 2 Dusdpfxjxqb Rco Ac Nsn E8000706 EDGE ROUNDING UNIT AR30 NC – 2 MOTORS E8000744 DEVICE FOR APPLYING SLIDING FLUID before EDGE ROUNDING UNIT E8000718 Additional pair of motors for quick change of finishing milling motors E0001706 Pair of cutters with replaceable blades – R = 2 mm. For edge rounding unit. E0001708 Pair of cutters with replaceable blades – R = 1 mm. For edge rounding unit. E8000910 EDGE TURNING UNIT RB400 E8000914 PRO-NESTING KIT FOR EDGE TURNING UNIT E0001915 Pair of multi-profile milling bits for edge scraper, 25° incline – R = 1 / 1.5 / 2 E8001011 GLUE TURNING UNIT RCC-701 Kit for sensitive panels for glue scraper unit E4000150 - Independent pneumatic shutoff of upper/lower unit. - Pressure adjustment glue for scraper blades. E8001035 Cleaning Brush Unit SP-501 E8000034 LPT-700 LIQUID APPLICATOR FOR CLEANING BRUSH UNIT E8001000 HOT AIR BLOWER PH-700 NSN19000 Parallelogram Linear Support, Scissor Type

Condition: used, tank capacity: 1,000 l, GENERAL Design: upright Remarks: Container outlet protrudes beyond container feet, container must be shimmed accordingly for installation; 1 separate base frame made of standard steel is included in the delivery; Total height includes base frame; Speed: 4.5 - 34 rpm Internal diameter: 1,100 mm Total height: 3,400 mm Heating/Cooling: available Power: 2.2 kW Djdjxqbq Ajpfx Ac Noun Agitator: anchor agitator Location: Bremen Cylinder temperature control: double jacket Volume: 1,000 litres Double jacket material: V2A 1.4301 (AISI304) Product-contact material: V2A 1.4301 (AISI304) Condition: used Cylindrical height: 1,100 mm Previous application: food TANK Support type: feet AGITATOR Voltage: 220/380 Volts Bottom bearing: Agitator arrangement: central on the top cover Agitator equipment: anchor with plastic scrapers (see photos)

Condition: reconditioned (used), Year of construction: 2018, operating hours: 3,317 h, overall weight: 19,000 kg, power: 389.81 kW (529.99 HP), Mobile shredder DOPPSTADT AK 560 Eco Power Dusdpot Egddjfx Ac Nsn Diesel engine: 530 HP Fine shredding basket (hole size on agreement) Rear discharge conveyor with magnet roll Hydr. self propelled drive (for moving on site) Twin drive separate drives for scraper floor and infeed roller Radio remote control

Condition: reconditioned (used), Year of construction: 2015, functionality: fully functional, overall weight: 22,000 kg, power: 375.1 kW (509.99 HP), year of last overhaul: 2024, Diesel engine: 510 HP Fine shredding basket; hole-size can be agreed. Foldable discharge conveyor Overband magnet Central lubrication Twin-drive (separate drives for infeed roller and scraper floor) Hydraulically self propelled drive (for moving on site) Radio remote control Duedpfjrrg Ifsx Ac Njn We can also offer financing if required.

Condition: reconditioned (used), Year of construction: 2016, functionality: fully functional, power: 389.81 kW (529.99 HP), Mobile shredder DOPPSTADT AK 560 Eco Power Diesel engine: 530 HP Fine shredding basket (hole size can be agreed) Rear discharge conveyor with magnet roll (magnetic head pulley) Dsdpfx Aew Rz Rqjc Noun Twin drive (separate drives for scraper floor and infeed roller) Hydr. self propelled drive (for moving on site) Radio remote control

Condition: used, tank capacity: 1,540 l, GENERAL INFORMATION Equipment: Spray head Design: vertical Remarks: Homogenizer mounted on the bottom (see photos) is included in the scope of delivery Heating/cooling: available Insulation: available Max. permissible operating overpressure: 6.0 bar Max. overpressure: 3.0 bar Agitator: propeller Agitators: 2 agitators Agitator type: anchor agitator Location: external storage Cylinder temperature control: double jacketed Nameplate: Volume: 1,540 liters Double jacket volume: 100.0 liters Product-contact material: V2A 1.4301 (AISI 304) Condition: used Previous application: pharmaceutical TANK Max. permissible operating temperature: 200 °C Support style: height-adjustable legs Number of legs: 3 pieces INSULATION Insulation jacket: hermetically welded Insulation jacket material: stainless steel EQUIPMENT Manhole/dome: on the upper head Dsdpfjycirgsx Ac Noun AGITATOR Agitator mounting: on the tank Agitator equipment: Scrapers are mounted on the anchor agitator (see photos) AGITATOR 2 Agitator mounting: on the tank

Condition: reconditioned (used), Year of construction: 2010, Voltage 400V 3~ 50Hz 7.22kW Control panel with LCD display and keypad Jointing unit with 2 counter-rotating diamond cutters Corner rounding unit for edge faces Duedpfxeyf I T Uo Ac Njn Manual unit adjustment Edge thickness 0.4-5.0 mm (optionally 8 mm) Workpiece height 8-60mm Feed speed 11 m/min 3 free slots for finishing units Edge feed for coil and strip material Scraper knife

Condition: ready for operation (used), Year of construction: 2009, This HOMAG KAL 330/6/A3/S2 was manufactured in 2009. A used edgebander featuring a gluing unit for EVA hot melt adhesive, pressure zone, cutting unit, copy milling, scrapers, and a buffing unit. Includes a LIGMATECH workpiece returning system. Consider the opportunity to buy this HOMAG KAL 330/6/A3/S2 edgebander. Contact us for more information. • Configuration/Features: • Joining milling • Gluing unit for EVA hot melt adhesive • Pressure zone Dsdpoychdusfx Ac Neun • Cutting unit • Copy milling • Scrapers • Buffing unit Additional equipment • Workpiece returning system: LIGMATECH

Condition: used, Year of construction: 2015, functionality: fully functional, total length: 7,920 mm, workpiece height (max.): 60 mm, warranty duration: 3 months, HOLZ-HER Edge Banding Machine ACCURA 1556 premium with intelligent equipment package for edge thicknesses up to 15 mm. Easy program changes and tool adjustments via the 18.5" touch control panel. Short heating time of the GlueJet adhesive system, approximately 2 to 3 minutes depending on adhesive type and ambient temperature. Always fresh glue thanks to the GlueJet adhesive application system and glue cartridges. Changing PUR glue and cleaning the system is extremely simple and can be done in just a few minutes. Axis adjustment via high-precision, repeatable servo motors. Special features for materials with protective foil, such as high-gloss and supermatt surfaces! One of the absolute highlights of this machine is the multifunction package, which excels in operations with many different edge types. The DIA tools are multi-stage and can switch between radii and bevels as the situation demands – from the longitudinal milling unit to corner copying and profile scraper. The extendable workpiece support and extended infeed section help with large workpieces, and a guiding system assists in feeding small workpieces into the machine. Edge thickness (coil material): 0.4 – 3 mm (depending on material) Edge thickness (strip material): 0.4 – 15 mm Workpiece thickness: 8 – 60 mm Workpiece width: min. 65 mm Feed speed: 10 – 25 m/min Glue application via GlueJet, suitable for both EVA and PUR adhesives, with minimal effort. Handles all popular edge types, including high-gloss & supermatt, as well as solid wood edges up to 15 mm. iTronic – pressure and glue amount control Prepared for connection to a RETURN system Motorized pressure bridge with top belt drive Multifunction units for quick setup of radius, flush, bevel Vertical & horizontal spray units and much more. Delivery, installation, and machine commissioning can be arranged directly through us at an additional cost. The machine is currently located in our delivery warehouse in Gratwein, Austria. In the event of discrepancies between the German version and any foreign-language version, only the German version is binding. Our general terms and conditions can be found on our website at holzher.de/de/agb. Duedjx Emf Depfx Ac Nen

Condition: new, Year of construction: 2025, operating hours: 671 h, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 450 mm, rapid traverse X-axis: 35 m/min, rapid traverse Y-axis: 35 m/min, rapid traverse Z-axis: 35 m/min, controller manufacturer: Heidenhain, controller model: Heidenhain TNC7, workpiece weight (max.): 1,100 kg, table width: 800 mm, table length: 616 mm, rotational speed (min.): 20 rpm, Equipment: chip conveyor, documentation/manual, rotational speed infinitely variable, Heidenhain TNC7 Spindle HSK-A63 16,000 rpm 30 tool positions Rigid clamping table 800x616 Internal coolant supply 40 bar with paper band filter Scraper belt conveyor Dujdpfx Acsyf E Ate Nen Handwheel BLUM LC53-Digilog for tool breakage detection/measurement Touch probe BLUM TC Machine ON: 671 h Spindle ON: 61 h Machine is approx. 6 months old. Offered for sale on behalf of customer. Inspection possible by prior arrangement.

Condition: used, Year of construction: 1994, Edge thickness 0.3 - 20 mm, edgeband height: max. 66 mm, edgeband length: min. 200 mm, workpiece width min. 60 mm, workpiece length min. 140 mm, workpiece thickness: min. 6 mm, max. 60 mm, feed speed 8 or 16 m/min - Edgebanding with Ultra - Granupress - End trimming with 2 saws, 0 - 15° tiltable - Milling, radius / flush - Corner copying - Scraper - Pneumatic buffing Location: Nattheim Dedpevvkdtsfx Ac Nsun

Condition: used, Year of construction: 1996, Edge thickness: 0.4 - 12 mm Roll edge: 3 x 45 mm or 0.8 - 60 mm Minimum workpiece width: 65 mm Minimum workpiece length: 160 mm Workpiece thickness: 10 - 55 mm Feed rate: 13 m/min Pre-milling (joining) Glue pot Quickmelt Gluing unit Trimming Flush trimming Chamfering Radius trimming Corner rounding Flat scraper Buffing unit Machine dimensions: 7450 x 1220 x 2400 mm Weight: 3000 kg Duodovvkd Tspfx Ac Nsn Storage location: Nattheim

Condition: used, Year of construction: 2009, HOLZ-HER edge banding machine CONTRIGA 1366 Edge thickness: 0.4-30 mm (depending on equipment) Edge height: 51/66 mm (depending on equipment) Panel thickness: 6-45/60 mm (depending on equipment) Edge types: Rolls and strips Feed speeds: Continuous feed from 12-30 m/min (depending on equipment) With adjustable infeed level in the magazine area (max. adjustment range 30 mm) With height-adjustable magazine plate for changing the lower edge overhang With large magazine plate Ø 820 mm for edge rolls up to Ø 800 mm With transport chain including automatic central lubrication With motor-driven, position-controlled bridge height adjustment With pneumatic locking roller for the shortest workpiece sequence With extendable workpiece support (extension width 1600 mm) With space-saving, pneumatically controlled sliding hoods over the entire machine (Deviations for individual units are possible) with motorized infeed guide with injection oiler for lubricating all joints and bolts (including operating hours counter) with central connection for extraction (2x Ø 200 mm) with integrated chip collection box at the end of the machine (when radius scraper unit is installed) PPC 231 control system - Power PC for efficient setup and changeover - 15" SVGA screen with touchscreen - 128 MB CF memory card - USB connector on board - Ethernet network connection - Keyboard connector on board - Windows-like user interface - all information in plain text and/or graphics - Rotatable and pivoting control panel at eye level - Dust-proof membrane keyboard with softkeys (pushbuttons) - LED display for unit preselection - Program list with program names and numbers - Extensive program memory - Individual selection of the units with the functions as basic setting options for setpoints, route points and tool corrections as well as the fixed route points - Centralized and clear setup processes for units and their axis settings via fine adjustment (depending on the equipment) - Interval display for the shortest workpiece distance - Integrated path control - Path points are controlled generally or program-specifically - Clear and complete recording of all operating data - Service messages in plain text - Diagnostic system - including integrated synchronous bus system for high precision in unit control - Individual administration for up to ten users, including password protection - Online maintenance (optional), data exchange with HOLZ-HER Service - Barcode interface (optional) BASIC MACHINE CONTRIGA 1366 - Belt bridge Options and accessories for the basic machine Spraying device 1856 for the inlet and outlet area For the inlet area: Electronically controlled release agent sprayer with Riepe-LPZ/II release agent For the outlet area: Electronically controlled cleaning agent sprayer with Riepe-LP163/93 cleaning agent (only in conjunction with pre-milling unit 1961 and surface scraper 1964) Joint milling unit Joint milling station 1803 (2x 2.6 kW, 200 Hz, 12000 min-1) With two plunge-controlled milling units 1 unit in up-cutting direction 1 unit in down-cutting direction Plunge path 5 mm With static frequency converter 200 Hz Without milling tool With ProLock screw-in clamp for fast tool changes Tool for 1803 (workpiece height up to 60 mm) Diamond milling cutter PRO UT 2 pieces (front and rear) including protective covers Ø 100-63 - Ø 30 mm, Z = 3 + 3 + 3, 1x left-hand rotation, 1x right-hand rotation Noise-reduced milling cutter with integrated chip guide DFC technology (Leitz syst Dsdjvvkfdspfx Ac Neun

Condition: used, Year of construction: 2001, Edge thickness 0.2 - 6 mm Workpiece dimensions Width min. 70 mm Height min. / max. 8 / 42 mm Length min. 150 mm (strip edges) Feed speed: 12 m/min Glue application roller Machine dimensions L x W x H = 3500 x 900 - 1300 x 1250 mm Weight: approx. 1130 kg Power consumption: approx. 6.0 kW, 400 V, 50 Hz Equipment: - Double top pressure with manual height adjustment - Automatic magazine for roll edges up to 800 mm DM - Rapid heating tank with application roller in synchronous and counter-rotating direction - Pneumatic adjustment and resetting of all work units - Pneumatic cross-cutting shears for strip edges up to 3 mm - Manually adjustable infeed ruler - Double cross-cut saw 2 HF motors 0.2 kW, 12,000 n 2 automatic Positions = 0 + 3 degrees - Milling/flush trimming unit with two HF motors 0.43 kW, 12,000 n. Two-sided scanning with two HF indexable cutter heads. Radius scraper, automatically controlled. Flat scraper, automatically controlled. Dedovvkfqjpfx Ac Njun Storage location: Nattheim

Condition: used, Year of construction: 2011, Pneumatic milling adjustment (Straight/Radius) Combination milling station R=2 Corner rounding cutter R=2 to 40 mm Jointing cutter up to 40 mm Flat scraper Profile scraper R=2 Short workpieces PLC control with Pro Face touchscreen Nesting Cooling/antistatic spray - airtronic Protective spraying Kante Riepe incl. interchangeable tank Workpiece thickness 8 - 60 mm Mechanical edge clamping Extraction nozzle: 140 mm Dimensions: Length with extension: 4984 mm Depth with roller table: 1425 mm Max. height: 1618 mm Worktable height: 888 mm Weight: 1400 kg Storage location: Nattheim Dodpfexyiilsx Ac Njun

Condition: used, Year of construction: 2006, EVA glueing, 2 pressure rollers, cross-cutting station, pre-milling cutter and rounding cutter, surface scraper, transport device Storage location: Nattheim Dodpjvvkg Iofx Ac Njun

Condition: used, Year of construction: 2012, cutting diameter 410 mm saw band length 5800 x 41 x 1,3 mm table height 750 mm 430 mm 410 mm 700 x 410 mm 410 mm cutting speed 500 x 410 mm down speed 320 mm dimensions of saw-band 320 x 410 mm workpiece weight 15 - 150 m/min 5,5 kW work height max. 3200 kg connected load 4500 x 2800 x 2000 mm Equipment: - Automatic cutting pressure and feed rate monitoring - Frequency-controlled AC drive 15-150 m/min, 5.5 kW - Hydraulic full-stroke material clamping - Automatic movement of the clamping vices - Automatic saw frame height adjustment - Minimum speed and saw blade monitoring - Electric miter tilting via servo motor - Visualized program input with CNC control - Integrated MEBA gripper infeed system from 5-2300 mm per stroke with integrated roller conveyor roller conveyor *Special equipment: - Laser light for cutting line display/ scribing saws - Driven chip brush - Micro dosing system - Clamping pressure regulation - Material bundle clamping - Job menu - Material database - Zero stop Duodjyb S Emspfx Ac Njn - Scraper belt conveyor for optimum chip removal, 2000 mm length - Cutting process control

Condition: good (used), Year of construction: 2022, operating hours: 167 h, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, Further technical data 5,964 linear meters total 167 operating hours High-precision cross-cut saw unit with radius milling up to 2 mm edge materials Jointing unit incl. diamond cutters 5 mm package for bonding solid wood edges Dsdpsyfv Ugsfx Ac Nsun "Quick-Set System" for rapid adjustment to various materials Control panel with LCD display and keypad Exchangeable glue pot Ball-bearing turntable for roll edge material Minimum workpiece width: 70 mm Minimum workpiece length: 210 mm Turntable diameter: 740 mm Edge thickness: 0.4–5 mm Extendable workpiece support, extendable up to 450 mm Additional equipment 21 Surface scraper instead of polishing unit 42 Application of release agent by spraying

Condition: good (used), Year of construction: 2017, operating hours: 130 h, functionality: fully functional, input voltage: 400 V, power: 6.5 kW (8.84 HP), input frequency: 50 Hz, Further technical data Edge thickness: 0.4–3 mm Workpiece height: 10–45 mm Chain feed with 8 m/min Total running length: 5,864 linear meters Jointing unit with max. 2 mm material removal Strip edgebander in single-feed operation Guillotine for hard PVC/ABS up to 3 mm thickness Teflon-coated glue pot, 1.2 kg capacity, with glue roller End trimming unit, 0.18 kW Extraction connections: 2x 80 mm, 1x 120 mm 2x HW saw blades, D-80 mm, Z16 Multi-milling unit with 12,000 rpm and 0.22 kW, 'Quickset' system for radius, flush and chamfer milling Control panel with LCD display and keypad Extendable workpiece support, extendable up to 450 mm Manually adjustable workpiece height: 10–45 mm Rotary table for edge banding rolls Minimum workpiece width: 70 mm Minimum workpiece length: 210 mm Extendable workpiece support, extendable up to 450 mm Manually adjustable workpiece height: 10–45 mm Duedpfx Aeyfvhasc Njn Additional equipment: Surface scraper, mechanically engageable Radius scraper knife

Condition: excellent (used), Year of construction: 2012, functionality: fully functional, travel distance X-axis: 600 mm, travel distance Y-axis: 500 mm, travel distance Z-axis: 500 mm, rapid traverse X-axis: 80 m/min, rapid traverse Y-axis: 80 m/min, rapid traverse Z-axis: 50 m/min, controller manufacturer: Heidenhain, controller model: iTNC530, table load: 400 kg, spindle speed (max.): 24,000 rpm, operating hours of spindle: 17,917 h, number of slots in tool magazine: 60, Equipment: rotational speed infinitely variable, Machine Description: - Universal 5-axis milling machine with linear drives in the X and Y axes, achieving 80 m/min traverse speed - Spindle and machine geometry in excellent condition - Regularly serviced - Last spindle replacement: 08/2020 / New control panel installed: 09/2025 - Current machine hours: Power ON: 58,985 h / Spindle ON: 17,917 h - Machine location: Lower Austria (near Vienna) Travel paths: X-axis (longitudinal): 600 mm Y-axis (cross): 500 mm Z-axis (vertical): 500 mm Clamping Table / Work Area: Integrated NC rotary table: 600 x 500 mm Duodpoya U Ibofx Ac Nsn Table load capacity: 400 kg CNC Control: Heidenhain iTNC530 Spindle: Speed range: 24,000 rpm Tool interface: HSK63 Coolant System and Chip Disposal: External coolant with 3 nozzles: 4 bar Internal coolant: 40 bar Paper band filter Chip conveyor, scraper belt design Automatic Tool Changer: Tool interface: HSK63 Number of tool pockets: 60 Dimensions and Weight: Machine: Length 2,900 x Width 2,611 x Height 2,865 mm Weight: approx. 9,800 kg Additional Equipment and Accessories: › Heidenhain TS 649 probe › Heidenhain handwheel › Blum laser for tool measurement on the table › Chip flushing gun › 3D Quick Set › ATC cycle package › Operating mode 4 › Integrated oil mist extraction › Operating manual / documentation › Dynamics package for linear drive, 80 m/min, incl. active cooler

Condition: new, overall weight: 2,600 kg, loading space length: 3,800 mm, loading space width: 1,800 mm, loading space height: 2,380 mm, 2 horse trailer with front exit and tack room from Cheval Liberte model TOURING-XL. High entrance door, elegant design, aerodynamic, various poly colors, aluminum walls and aluminum floor. Djdpfsq Nf S Uox Ac Neun Horse transporter for two horses with outstanding driving comfort! The aluminum horse trailer is equipped with Pullman 2 running gear developed by ChevalLiberte. An entrance just 35 cm high, independent suspension, trailing arms, coil springs and shock absorbers provide these outstanding driving characteristics. A flat overrun flap, which can also be opened like a door, makes the horse transport trailer a universal trailer for easy loading of pallets, for example, or for better cleaning of the interior. For the horses it is less stressful and less likely to injure them as they cannot slip off the flap. The two-horse trailer also has a wide range of features such as front exit, tack room, polyester hood in various colors, aluminum walls, aluminum floor, high entrance door, folding door system, Pullman2 chassis, 100km/h, interior light, automatic support wheel, four sliding windows, stable frame, V-drawbar and so on. Inexpensive accessories such as a tethering bracket, feed bucket, drawbar protection cover, double-leaf door, trailer lock, aluminum rims and scraper mats are also available. The body is splash-proof.

Condition: new, empty load weight: 850 kg, maximum load weight: 1,750 kg, overall weight: 2,600 kg, loading space length: 3,150 mm, loading space width: 1,660 mm, loading space height: 2,300 mm, tire size: 185/65r14, 2 horse trailer with tack room from ChevalLiberte model TOURING-JUMPING. Spacious entrance door, elegant design, aerodynamic, various poly colors, aluminum walls and aluminum floor. Horse transporter for two horses with outstanding driving characteristics! The aluminum horse trailer is equipped with Pullman2 running gear, which was developed by Cheval Liberte itself. A 35 cm access height, independent suspension, trailing arms, coil springs and shock absorbers ensure unrivaled driving comfort. Dodpfx Acehuc R Us Njun A flat loading ramp makes loading and unloading very safe. The ramp-door combination of the horse transport trailer is outstanding. This means that pallets and horses can be loaded stress-free and without injury and the interior is easier to clean. This prevents the horses from slipping off the flap. The two-horse trailer is equipped with tack room, polyester hood available in various colors, aluminum walls, aluminum floor, high entrance door, folding door system, Pullman2 chassis, 100km/h, interior light, automatic support wheel, four sliding windows, stable frame, V-drawbar and so on. You will find the complete equipment below. Inexpensive horse trailer accessories such as a tethering bracket, feed bucket, weather protection hood, drawbar protection, trailer lock, aluminum rims and scraper mats are also available. The body is splash-proof. --- You can also find all our low-cost offers on our homepage Germany-wide delivery (except islands) possible! for the prices. --- PKW-Anhänger-Center Ahrens Moordeicher Landstraße 37 28816 Stuhr near Bremen Tel: 0 Fax: Pick-up times: Monday - Friday - o'clock Saturday is not possible!