Used Deburring for sale (391)

Condition: used, Year of construction: 2007, working width 1380 mm workpiece height 70 mm Iodpfxst Hw Iij Adnja total power requirement 45 kW weight of the machine ca. 5.500 kg

Condition: used, TECHNICAL DETAILS - Tank capacity : 4 x 8L * Speed : 23-132 [rpm] * Power : 0,25 [kW] - Drum diameter : 402.5 [mm] Ijdpfx Adew Hufuenea - Useful volume : 14 [l]

Condition: as good as new (ex-display), Year of construction: 2024, Boschert brush deburring machine model K3 for deburring straight sheet edges and on the lateral aggragate suitable for cut-outs and notches up to 70 mm deep as well as outer radii on sheet metal. 3 motors á 1,5 kW brush diameter : 300 mm Material: wire brushes VA/steel Material range: 0.8-8 mm thickness Machine dimensions: Width: 1400 mm Height: 580 mm Depth: 670 mm Underframe: 800 mm high (working height 920 mm) Table support: 200x1400 mm Hold-down device as sheet guide The sheet edge is deburred simultaneously from above and below as it passes by. If the burr is very thick, the motors can be synchronized so that both remove the thick burr from the top. The 3rd (lateral) unit is for deburring external contours and is switched on separately. A larger lateral table support serves as a shelf Ijdetr Avijpfx Adnja

Condition: reconditioned (used), Year of construction: 2017, operating hours: 3,862 h, functionality: fully functional, Used machine Year of manufacture: 2017 General Specifications: Max. working width sanding belt unit: 1350 mm Sanding belt dimensions (W x L): 1380 x 1900 mm Outside brush diameter: 350 mm Table opening: 0 – 100 mm Minimum workpiece size: 50 x 50 mm Feed speed, frequency-controlled: 0.5 – 8 m/min Electricity 1st Unit – W – sanding belt: 11 kW 2nd Unit – RB – rotary brush unit: 1.5 kW Brushes: 4 x 1.5 kW (6 kW) Iedpsw Dzytefx Adnsa Feed motor, frequency controlled: 2.6 kW Vacuum pump: 15 kW Electrical connections: 400 Volt Frequency: 50 Hz Compressed air only for sanding belt unit Required air pressure: 6 bar Consumption: 160 l/min Dust extraction at 100 mm WS Sanding belt unit: 2000 m³/h Vacuum pump: 1500 m³/h Weight: approx. 6000 kg Includes one set of brushes and starter set of sanding belts. New extraction system optionally available. Machine has been technically overhauled (conveyor belt and bearings are new, value approx. €20,000) Immediately available.

Condition: used, Year of construction: 2019, operating hours: 2,120 h, functionality: fully functional, machine/vehicle number: SN026032, The machine was used in our own production facility in Bad Wurzach, Equipment: mold | mold closing compensation | camera set. As a package with 2 conveyor belts and a WDE 3002 wet extraction unit. Further information on request. The SBM-XL S2B2 grinding and deburring machine is designed for edge rounding and oxide layer removal on both sides of steel parts and stainless steel in a single operation. The LISSMAC system is suitable for processing laser parts. Technical data SBM-XL S2B2: Passage width: max. 1500 mm Processable sheet thickness: 0.5 - 50 mm Load capacity: 300 kg/lfm Voltage: 400 V / 50 Hz Isdpfx Adjt Tx Dxsnea Mains form: 3~ PEN / 3~ PE+N Rated current: 74.3 A Rated power: 33 kW Protection class: IP 42 Infinitely variable feed: 0 - 4 m/min. Sheet thickness adjustment: electric Tool setting: electric Weight: approx. 4200 kg Dimensions (W/D/H ): approx. 3600/2100/2000 mm

Condition: used, Year of construction: 2015, Technical details: Iedpel Ha Ubjfx Adnea weight of the machine ca.: 4 t

Year of construction: 2002, condition: used, diameter 180 mm workpiece length 0 mm work piece width 1350 mm total power requirement 65 kW weight of the machine ca. 7.500 kg Iedpfxjt Hw Shj Adnea dimensions of the machine ca. m

Condition: used, Year of construction: 2008, working width / mm workpiece height / mm / Workpiece thickness: 1-70 mm Min. workpiece length: 350 mm Min. workpiece length with magnetic or vacuum track: 80 mm Band filter unit volume Ab=900 approx. 350 l Band filter unit volume Ab=1400 approx. 400 l Working height constant 1000 mm Feed speed 2/4 m/min Feed speed stepless 1.5-8 m/min Operating voltage 400 VAC Control voltage 24 V DC, 230 VAC Frequency 50Hz Compressed air connection R 3/8" Minimum compressed air pressure 5 bar Minimum compressed air volume EMSN II +2F 10 NI/min Minimum compressed air quantity EMSN II /L +2F 80 NI/min Overall electrical connection See installation plan Weight of the machine working width 900 mm approx. 4200 kg Weight of the machine working width 1400 mm approx. 5100 kg Weight of the machine working width 1540 mm approx. 5600 kg Sandpaper dimensions sanding roller AB=900 1540 mm long x 900 mm wide Sandpaper dimensions sanding roller AB=1400 1540 mm long x 1400 mm wide Sandpaper dimensions sanding roller AB=1540 1540 mm long x 1540 mm wide SERIOUS Automatic sheet metal deburring machine with wet grinding device Type EM 5 N/II/L + 2 F 1400 Year of construction 2008 Factory - No. 780063 Machine/Equipment: Sheet metal deburring machine using the wet ship process for stamping, laser and nipple parts of different materials with flexible grinding roller, as well as 2 flap brushes for particularly high edge rounding and 2 Spring steel brushes for oxide removal (worn out) The machine is equipped with a continuous conveyor belt for the Workpiece transport equipped. Effective working width: 1380mm Minimum workpiece length: 350mm Iodpfx Aeinwwzodnoa Special equipment: •Vacuum suction system 300mm wide, for non-magnetic small parts Minimum length of 80mm, with a minimum area of ??200cm² •Magnet track 300mm wide Minimum length of 80mm, with a minimum area of ??40cm² •Frequency converter for stepless feed & speed regulation •various Abrasives as accessories

Condition: ready for operation (used), Year of construction: 2017, operating hours: 7,464 h, functionality: fully functional, machine/vehicle number: 0041, feed length X-axis: 400 mm, feed length Y-axis: 400 mm, feed length Z-axis: 600 mm, workpiece weight (max.): 20 kg, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Work area Cubic travel area: 400 x 400 x 400 mm Electromechanical adjustments Adjustment in Z-axis: up to 600 mm manually Travel in X,Y axes: ±200 mm each Rotation around A or B axis: ±45 degrees each Adjustment speed: 1 m/s Load capacity: 20 kg Operation Control: BOSCH REXROTH Connection data Connected load: 21 kVA Operating voltage: 400 V Isdpfx Aswrr Tyjdnja

Condition: like new (used), Year of construction: 2021, functionality: fully functional, working width: 1,350 mm, Grinding and deburring machine COSTA MD5 CVC 1350 Grinding, deburring, edge rounding and finishing of serial components Year of manufacture: 2021 Control: Costa Operating hours: rarely used Iedpfx Adewq Dnmenoa Technical data: Free-standing machine Working height: variably adjustable from 0.5 mm to 150 mm Working width: 1350 mm Max. part weight: 400 kg Length of wide belt grinding belts: 2620 mm Constant table height, feed via grinding units Intuitive PLC control for creating, saving and retrieving programs Electromechanically positionable grinding units in 0.01 mm increments Accessories: - Extraction: Wet separator extraction unit W 4000

Condition: like new (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: SN040890, working width: 1,350 mm, sheet thickness (max.): 120 mm, total length: 3,300 mm, total width: 2,170 mm, total height: 2,260 mm, workpiece weight (max.): 500 kg, overall weight: 5,200 kg, input voltage: 400 V, warranty duration: 12 months, protection type (IP code): IP42, input frequency: 50 Hz, input current: 56 A, GRINDING AND DEBURRING MACHINE FOR HEAVY PLATE. SLAG REMOVAL, DEBURRING, EDGE ROUNDING | Equipment: Tool, magnetic track, conveyor belt cleaning brush, internal lighting, ME 5000, ID key switch, camera set, LiServ, energy measuring package. Available from October 2025. | SMD 335 DRE - P Edition Passage width 1350 mm Processable material thickness 1.0 – 120 mm Load capacity 500 kg/m Voltage 400 V / 50 Hz Ijdpfxjwza Udo Adnoa Power supply 3 + PE / 3 + PEN Rated current 56.0 A Rated power 25.5 kW Protection class IP 42 Feed rate stepless 0.3 – 8.0 m/min Weight approx. 5200 kg Dimensions (W/D/H) approx. 2170/3300/2260 mm

Condition: excellent (used), Product Information "POLY-PTX 800 satin finishing machine" From the inventor of the longitudinal sander. Our multifunctional longitudinal sander with 1750 watts of power, speed control, ergonomic design and versatility - including up to 150 mm working width. High torque and power reserves guarantee professional, continuous use and greater profitability. Features: Infinitely variable speed control from 1000 to 3800 min-1 with a tachogenerator to ensure constant speed even under load. Grinds from coarse to fine. Balanced, simple manual guidance without support rollers. This allows free movement (oscillation effect). Guarantees shadow-free, seamless, highly decorative surfaces in satin, matte and industrial finishes. It satin polishes to a mirror shine and refines the surfaces of stainless steel, steel, non-ferrous metals such as brass, bronze, copper, aluminum, as well as wood. Finest sanding on large surfaces, without shadows or edges. Removes welds, deep scratches, rust, dirt, layers of paint and oxides. Goes from coarse grinding to mirror shine on stainless steel and non-ferrous metals in just three steps. It's also ideal as a round tube grinder using a sanding belt roll. Grinds and polishes open and closed pipe structures. For pipe processing, the "hole system" allows safe and fast bonding of fleece and felt tapes to closed pipe structures. It does not require complex tape bonding. Ijdpfsu Su Tzsx Adnsa Huge range of grinding tools , which offers a solution for every task. With rubberized handle for optimal handling! Set contents: 1 POLY-PTX® 800 basic unit 1 robust, impact-resistant plastic carrying case 1 QUICK-LOCK cable 4 m 1 POLY-PTX® mounting screw 1 fleece disc 100 mm wide Machine type: Satin finishing machine Cable/battery: Cable Suitable tools: Brushes, bushings, polishing rings, wheels Plug type/power connection: EU (C+F) 220-240 V ~ 50-60 Hz Power consumption: 1750 watts Max tool size: Diameter 115 x width 100 mm Tool holder: 19mm spline shaft WEEE Reg. No.: DE 51395731 Speed in min-1: 1000 - 3800

Condition: like new (used), Year of construction: 2019, 2 sanding units with inverter predisposition for 3rd unit Suction table Isdpfxswqrtqj Adnea Working width 950 mm

Condition: good (used), Year of construction: 2005, working width: 1,000 mm, Deburring machine Ijdpfx Ajvgb Hgjdnea Fab. LISSMAC Typ. SBM-B 1000 Year 2005 Technical data Make: LISSMAC Type: SBM-B 1000 Year of construction: 2005 Passage width: 1000 mm Sheet thickness: max. 20 mm Sheet size min. length: 150 mm Sheet size min. width: 100 mm Speed: 1400 rpm Brush motor power: 4 x 7.5 kW Dimensions: approx. L 2.20 x W 1.50 x H 1.50 m Weight: approx. 1.5 t Equipment - Automatic material feed-through - Infinitely variable feed rate 0-10 m/min - Sheet thickness adjustment: Hand crank with worm gear and scale, infinitely variable - Brush depth adjustment: Hand crank with worm gear and scale, infinitely variable - Various accessories - Operating instructions All information without guarantee. A demonstration is possible at any time in our showroom.

Condition: used, Deburring machine, hole deburrer, hole deburrer, deburring device, brush deburring machine -Manufacturer: Wedge, deburring machine Keil-Single with base frame -Drive: 3.0/2.0 kW / 3000/1500 rpm -Brush: Ø 200 mm, Ø 200-250-300 mm possible -Brush width: 60 mm, 20-40-60-80-100 possible Isdpferw Daaex Adnoa -Total dimensions: 800/800/H1210 mm -Total weight: 110 kg

Condition: new, filling capacity 750 kg max. workpiece height 900 x 300 mm workpiece weight total 550 kg max. workpiece weight 30 kg / Stck. revolutions per minute 22 U/min filling amount 50-60 % Colour blau 5015 RAL 0 1775 x 440 mm total power requirement 3 kW weight of the machine ca. 1995 kg dimensions of the machine ca. 2,9 x 1,33 x 1,75 m Iedpfxsvv H Tdo Adnea New deburring machine for safe and to efficiently deburr workpieces. Suitable for heavy applications. The EVO model is available for light to medium workpieces. 6 - square drum lined with durable, vulcanized rubber thickness 36 mm, locking cover with gas pressure springs, roller shutters to protect againstthe rotating Container, stable design, easy operation. Control by timer on control surface, main and emergency stop switch. The maximum fillingquantity is 40% of the container volume and corresponds to 800 kg consisting of 500 kg workpieces + 300 kg deburring medium = hard manganese balls pic 6 or cast iron pentagons pic 7. These are over Sideros available. Stepless speed adjustment via frequency converter approx. 13-22 rpm (2850,-- €) Soundproof housing (65/70 Db) photo 7 and Sideros ECO B2 dust extraction against Available at extra cost. For complicated workpieces, the manufacturer recommends 100 kg sample parts of the material to be deburred to the factory for testing before ordering. VIDEO on our website. Machine dealer with own stock of 1600 m².

Year of construction: 2025, condition: new, working width 950 mm workpiece width - max. 1,0 - 50 mm sandingbelt width 970 mm sandingbelt length 1900 mm weight of the machine ca. 1,8 t The SMD 123 RE is a universal entry-level machine for all-round deburring Uniform edge rounding and surface grinding of sheet metal dry process. * Suitable for processing steel, stainless steel and aluminium. * The non-slip conveyor belt enables safe transport and the Machining even of small workpieces. * The two rotor heads ensure an all-round uniform Edge rounding and a directionless finish. * The intuitive operation via touch panel allows every employee Iedpfxevfhm Do Adnsa get to grips with the machine quickly. * The SMD 1 models are installed and ready for operation in a short time. * The compact design saves valuable production space. * Low acquisition and operating costs lead to short amortization periods and guarantee economical processing of your workpieces. consisting of: - Grinding machine SMD 123 RE (kit): - SMD 123 RE conveyor belt cleaning - SMx xx3 - sanding belt +120 Cubitron II, W=970, L=1900 - SMD 1x3 set grinding flap roller 3-piece. P120 - DDE 3002 dry suction - Standard piping DDE 3002 / WDE 3002 for SMD 123, SMD 133 Further detailed technical data on request. The machine is in stock Niederlangen available immediately.

Condition: good (used), Year of construction: 2011, Edging and contouring - deburring machine ROLEI Type: 00645-KKE2 Year: 2011. Isdpfswnpflex Adnsa

Year of construction: 1963, condition: used, max. wheel diameter 2000 mm Ijdped Ngrpjfx Adnea gear width 0 mm max. module 0 Weight ca 700 kg dimensions of the machine ca. 2x1,2x1,5 m uncomplete machine body with drive motor. drive unit fully functional. Without grinding unit.

Year of construction: 1997, condition: used, Brush deburring machine RSA RASAMAX MONO for brushes Ø 250 mm and approx. brush width 80 mm speed range 1500 / 3000 rpm Iedpfxsimbq Ds Adnoa operating voltage 380 volt total power requirement 2,0 / 3,0 kW Weight approx. 180 kg for deburring of sheet metal with contours for material thickness from approx. 1,0mm to 6,0mm. Brush speed 2-stage 1500 or 3000 rpm Machine is located in 71334 Waiblingen-Beinstein and can of course be inspected, please contact us.

Condition: used, Deburring machine, hole deburrer, bore deburrer, deburring device Iodpob U Izpsfx Adnoa -Drive: 0.30 kW -Countersink -Speed: 585 rpm -Dimensions: 500/300/H460 mm -Weight: 31 kg

Condition: new, filling capacity 300 kg Isdpeu Uu T Rsfx Adnoa max. workpiece height 500 x 200 x 20 mm workpiece weight total 200 kg max. workpiece weight 15 kg / Stck. revolutions per minute 22 U/min filling amount 40-50 % Colour blau 5015 RAL 0 625 x 270 mm total power requirement 1,5 kW weight of the machine ca. 650 kg range L-W-H 1 x 1,7 x 1,29 mm New deburring machine for safe and to efficiently deburr workpieces. 6 - angular drum lined with wear-resistant vulcanized rubber 36 mm, roller shutter to protect against the rotating container, stable design, simple service. Control panel with timer, hour counter, main and emergency stop switch and signal lamp. The maximum filling quantity is 40% of the containervolume and corresponds to 300 kg consisting of 175 kg workpieces + 125 kg deburring medium = Hard manganese balls pic 6 or cast iron pentagons pic 7 (50 kg is included in the price). This are available from Sideros. Sideros ECO dust extraction available at extra cost. The manufacturer recommends taking 100 kg samples of the material to be deburred to be sent to the factory in Italy for test purposes before ordering. Machine dealer with own stock of 1600 m².

Condition: new, GRATMAXX Bürstentgratmaschine The machine is suitable for the deburring of edges on: Round tubes, square tube, rectangular tube, full materials, profiles of all kinds. Materials: Steel non-ferrous metals, plastics, hard or soft. Isdpfxjd Hmnfe Adnja Work flow: After setting the workpiece support and dern side stops the Ridge-workpiece is easily kept on the brush rotating around its own axis, without rotating the workpiece, this movement is also the brush. The workpiece material, the Ridge strength, as well as the desired rounding of the edges determine the pressure and the duration of contact seconds, usually around 1-5. Technical data: Material: Steel, stainless steel and non-ferrous metals (engine speeds 700-1,900 rpm, infinitely variable) Min. workpiece-Ø: 5 mm Maximum work piece-Ø: 100 mm (150 mm) Brush dimensions: 2 piece Ø300 (250) x 50 or 3 piece Ø 300 (250) x 35 Power: 3,0 KW Power: 3.5 KW Operating voltage: 3 ~, 400Volt, 50 Hz Rated current: 8A Back-up fuse: max 16A Control voltage: 24V/DC Width: approx. 500 mm + Handwheel 74 mm, + dust spout 130 mm Altitude: 1.382 mm Working height: approx. 1.080 mm Depth: 1,209 mm Weight: 310 kg Sound pressure level: At speed 700 rpm 64 dB(A) at a speed 1500 rpm 74 dB(A), when machining a workpiece with maximum speed of 82 dB(A) Scope of delivery: Rotary head Bürstentgratmaschine GratMaxx with power socket without cable Workpiece support table with adjustable angle stop and

Condition: used, Year of construction: 2016, Working hours machine: 5320 h max. working width: 300 mm workable material thickness: 1-15 mm Tension: 400V / 50 Hz Total power: 13,5 A Total current consumption: 7,5 kW Insulation class: IP42 Infinitely variable feed speed: 0-2 m / min Length: 2600 mm Width: 2300 mm Height: 1300 mm Isdpfxsv N I Hlj Adnja Machine weight: 1900 kg Standard configuration - With a magnetic table designed for part dimensions of 25 x 25 x 1 mm up to maximum 200 x 200 x15 mm (geometry-dependent)- With vacuum table for part dimensions of 45 x 45 x 1 mm up to maximum 200 x 200 x15 mm (geometry-dependent)- Time consuming turn-over of parts with a second pass is not necessary- Swinging away of the innovative turning station makes it possible to deburr parts longer than 200 mm- A higher level of automation ensures an economic and reliable deburring process, also for large quantities of parts- A high and sustainable deburring quality.- Dry deburring process (no chemical additives as used in tumblers)- Small parts are returned to the front of the machine and gathered in a box. No extra walking back and forth for the operator.- Energy-efficient- The deburring process ensures an even wear of the belt and brushes across the entire width of the machine- Fast and simple tool Change- Simple and intuitive operation of the machine- Modern, compact machine design Extended machine accessories

Condition: used, Brush deburring machine, sheet metal deburring machine, deburring machine, -Deburring machine for: punching, laser and nibbling parts Isdpfx Adsd Nq A Ujnoa -Deburring system for: sheet metal edges with notches -Drive power: 0.71 kW Speed: 4500 rpm -Dimensions: 400/180/H130 mm -Weight: 3.5 kg