Used Cross Carriage for sale (5,874)

Condition: used, Year of construction: 2009, conveyor belt, belt conveyor, transport belt, belt conveyor -Manufacturer: Grenzebach, conveyor belt 2 levels type EZT with guide rollers Dkodpfx Acstrhm Ao Nji -Speed: frequency controlled -Drive: 2x SEW Eurodrive -Conveyor belt length: 1400 mm -Belt spacing: 410 mm -Cross carriage: roller spacing 1000 mm -Number: 2x conveyor belt available -Price per piece -Dimensions: 1450/1550/H920 mm -Weight: 358 kg/pc.

Year of construction: 2013, condition: used, Technical data of the bale opener line for RDF. MSW, paper, cardboard: Manufacturer Cross Wrap Oy Ltd, Siilinjärvi, Finland Type BO 4000 Year of manufacture 2015 Quantity of opened bales 674 pieces Operating time only 3 days, exclusively by running in the entire line during new installation Opening time approx. 45 seconds per bale Bale dimensions (W x H x L) 1100 x 1100 x 1400 - 1900 mm Max. Bale weight 2,000 kg Conveying height of the system 1,400 mm Max. Conveying width of the system 1,200 mm Material to be opened RDF/MSW Availability of the line 98% Noise level of the bale opener line 85 dB(A) Total connected load 37 kW Rated current 125 A Operating display SIEMENS SIMATIC HMI Touch Control SIEMENS S7 ET200S Installation dimensions 8,463 x 2,890 x 3,960 mm (l x w x h) Scope of delivery: Feed conveyor 3,500 x 1,200 x 1,400 mm Feed conveyor to opener 1,500 x 1,200 x 1,400 mm Bale opener (gripper with knife) Special equipment: Oil heating in hydraulic oil tank Heating in control cabinet Oil cooler in Hydraulic unit Explanation of the short period of use: The entire line of Cross Wrap bale openers type BO 4000 was installed at a municipal waste incineration plant in 2015. The background to the installation was that in the case of a malfunction or maintenance of the incinerator, the municipal waste could continue to be received, baled, wrapped and stored until the malfunction was cleared. Then the bales should all be opened again and the waste fed into the normal incineration process. This worst-case scenario never came to pass. The plant was set up, run in and then never used in regular operation. Only during the commissioning and running-in of the entire plant in 2015 were 674 bales opened on three days. The plant is in very good condition and ready for operation immediately. Due to reconstruction measures in the incineration plant, the installation area of the bale opener was needed. As a result, the entire line is for sale. Short description of the wrapping process: The pressed bales are placed on the infeed conveyor belt from the side or from behind by means of a forklift truck. For opening, the bales must run horizontally to the conveyor belt with the wire or twine binding, otherwise the bales must be turned 90° beforehand. The opening conveyor brings one bale at a time in front of the cutting unit. The grippers hold the wires or twine strapping. The front and rear rotating knives slit the bale lengthwise. Afterwards, the gripper returns to the starting position. The opened bale is now conveyed via the conveyor belt to the discharge chute and then falls onto the following conveyor system. Comments: Djdpfx Aju Tg I Djc Nski New price of the completely plant 296.000,- €. The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) is complete. The unit has been dismantled into freight-manageable units, stored and is available for inspection and loading at short notice. We do not accept any liability for the technical details or any errors.

Condition: excellent (used), Year of construction: 1997, Rip and cross saw REMA DMLK 30 Producer of REMA Machine model / type DMLK 30 Year of production 1997 Machine category Longitudinal and transverse saw Location Gorzów Wlkp. Conditions of delivery PERSONAL COLLECTION Cost of delivery Customer cover Startup type to be agreed Description Comments - after the technical review - very good condition - year of production 1997 TECHNICAL PARAMETERS: main engine 3.9 kW trolley length 1370 mm blade diameter 300 mm angle adjustment 0 - 45 " height adjustment cutting height max. 90 mm cutting width on the right side 885 mm Dodpfx Acsfv Hphj Neki ruler length 1350 mm ratchet extended receiving table two kinds of blade rotation speed 3700 and 5000 RPM The protractor visible in the photos is an additional option for PLN 400 net dimensions: length / width / height 135 x 85 x 135 cm weight ~ 320 kg

Condition: like new (used), Range (in depending on the lighting conditions) until: 15 m Range with laser receiver: 30 m, & more 5 m: leveling accuracy +/-1 mm Self leveling range: 4° +-0,5 ° Accuracy of the horizontal line at 5 m: +-1.5 mm Accuracy of vertical line at 3 m +-0.75 mm Number of laser lines: 2 Weight: 485 g Dedpfx Aod Ecncoc Nski

Condition: used, Roller conveyor with chain cross conveyor Dksdpfx Acoi Sdk Se Nei Can be used after resaw. - Electric motor: 1,1 kW - Electric motor: 0,75 kW - Electric motor: 1,1 kW

Condition: ready for operation (used), Year of construction: 2003, This DIMTER S50 Opticut was manufactured in 2003. A robust optimizing cross-cut saw, it features a processing length of 5 m and a saw blade diameter of 500 mm. A new Movidrive converter was installed in 2018, enhancing its performance. If you are looking to get high-quality cutting capabilities, consider the DIMTER S50 Opticut machine we have for sale. Contact us for more information about this machine. Dkjdpfxjx D Hxrj Ac Nji Application Types Sawing (Wood)

Condition: new, Number of milling spindles 2 St. fence 1 ja workpiece ja Cross rung milling machine STEGHERR TYPE KSF-mini including standard stop with 2 sliding stops, without tools With the KSF-mini, all of those that occur in practice can be used Crossbar connections can be made quickly and precisely. The Precise execution is achieved by having the workpiece in one Clamping is machined on three sides. The tool is driven by two three-phase motors; the tension of the Workpieces pneumatically. The profile cutter is designed for the web width. The saw blades that... If you carry out flattening, spacer rings are used to match the dimensions of Dsdpfeyrtzqox Ac Noki the Profile milling cutter adjustable. The swivel device is free of play. The machine is designed for a maximum workpiece cross section of 56 x 46mm. Voltage Europe: 400V(+/-10%)/3Ph/50Hz, USA: 440V(+/-10%)/3Ph/60Hz Other voltages on request. Operating instructions in German or English. Table base € 1.030.00 Foot switch € 870.00 Adjustment optics € 130.00 Profile milling cutter in HM-Wepla version, available for selection: Ø 5,7,9,11,13 mm. Price per piece € 630.00 1 set of replacement insert knives for profile milling cutters (=10 pieces) € 180.00 HM saw blade, price € 160.00 per piece (For a web of e.g. 10 mm, 3 saw blades are required) Setting the machine to the tools provided by the customer, price € 680.00 per individual tool Packaging in a crate (suitable for land transport) € 650.00 Packaging shrink-wrapped on a pallet (only within Europe, not for air freight) € 340.00 Pricing ex works, unpacked, uninsured, for delivery within Germany plus the VAT valid at the time of delivery. (all technical information according to the manufacturer, without guarantee!)

Condition: used, Year of construction: 2003, total height: 1,500 mm, total length: 11,250 mm, total width: 900 mm, Price: On request - Year: 2003 - Documentation available: No Dedpfsyrggtjx Ac Noki - CE certificate present: No - Serial number: 1344.14 - Main motor power [kW]: 5.5 - Max. saw length [mm]: 6100 - Max. saw width [mm]: 350 - Max. saw height [mm]: 110 - Max. saw blade diameter [mm]: 500 - Input table length [mm]: 7850 - Output table length [mm]: 2400 - Options: Automatic pusher system - Voltage [V]: 400 - Fuse [A]: 25 - Power [kW]: 7.0 - Transport dimensions: 11250mm x 900mm x 1500mm (l x w x h) - Transport packages [pcs.]: 3 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: excellent (used), Catalogue number 7837 TECHNICAL DATA - Max. blade diameter: 450mm - Spindle diameter: 30mm - Top pneumatic hold-down - Blade guard Dkjdpfx Ajx Arhcoc Nei - Blade guard also functions as a hold-down - Pneumatic blade stroke - Cutting height: 125x125mm, 100x250mm - Cutting capacity (thickness x width): 50x530mm, 100x480mm, 150x380mm, 200x200mm - Main motor: 5.6kW - Extraction port diameter: 100mm - Table dimensions (L/W): 660x480mm - Table height from base - 2 roller tables - Infeed roller table with guide: 1500mm - Outfeed roller table with guide and latch: 1500mm - Roller width: 300mm - Working pressure: 8bar - Overall machine dimensions (without roller tables) L/W/H: 940x780x1150mm - Weight approx. 450kg ADVANTAGES – German manufacture – DTR documentation – 2 roller tables – Pneumatic blade stroke – Saw used, in perfect condition Net price: 14,900 PLN Net price: 3,550 EUR (based on exchange rate 4.2 EUR) (Prices may change in case of significant exchange rate fluctuations)

Condition: excellent (used), Year of construction: 2009, HOLZMA cross-cutting machine for dividing panel remnants, such as those produced in angular panel saw lines – part of the automatic waste disposal system at panel dividing plants. TYPE HRZ 540 Year: 2009 Machine No.: 0249083537 For trimming off-cuts and remnant cuts at an angular system. The off-cuts and remnant strips are conveyed directly from the shaker chute of the longitudinal saw into the cross-cutting machine, where they are cut down to approx. 200 – 400 mm. Trimming is performed by a hydraulically operated cutting blade. Dksdpfxoyay Igj Ac Nji Head and edge trimmings drop down through the waste flap into a shaker chute below. This chute conveys the remnants to a shredder (cross-cutting machine). From there, the shredded waste is transported, e.g. via a waste conveyor belt, into a scrap container.

Condition: used, Year of construction: 2003, The Mueller Martini CB 16 stacker, manufactured in 2003, is a robust and efficient solution for stacking and organizing printed materials. With a format of 500 x 340 mm, this stacker is currently in production and located in the United States. The delivery terms are FCA (Free Carrier), meaning the seller delivers the goods, cleared for export, to the carrier appointed by the buyer. The machine is in good condition, ensuring reliable performance for various stacking tasks in printing and finishing applications. Format: 500 x 340 mm Equipment: Good condition without any damage Dkedpfx Acjvmnfps Nsi

Condition: used, Year of construction: 2001, Wood dimensions to be processed: Input lengths min/max 500 - 6500 mm Full optimization up to max. 1500 mm Input widths min/max 40 - 300 mm Input thicknesses min/max 15 - 120 mm Wood cross-sections max. 300 x 40 mm max. 200 x 120 mm Fixed lengths after sawing min. 510 - 2800 mm Special application: Cutting blocks, length min/max. 100 - 200 mm (Caution: Multiple block lengths at the sorting line; blocks are transported to the end of the sorting line and fall into the customer's grid box). Cutting/cutting tolerance +/- 0.8 - 1.5 mm (for wood types with minimal resin content and an even surface. Tolerance up to 1 m fixed length, max. tolerance for longer pieces up to 2.5 m). Thickness tolerance +/- 3 mm. Curvature of the wood in all directions: max. 10 mm per meter in length. Wood types: soft or hardwood. System performance: Feed speed, continuously adjustable up to max. 230 m/cutting cycle 0.6 - 1. To obtain the practical output per day, an effectiveness factor dependent on the customer's production conditions must be calculated. Infeed and saw height: 900 mm (placed on customer's platform, saw requires concrete base). Sorting working height. 2000 mm Connection values: Total electrical connection value approx. 18 kW Operating voltage 380 Volt / 50 Hz Voltage fluctuations max. 5% Air consumption approx. 1200 NL/operating pressure approx. 8 bar Extraction speed approx. 30 m/nd Color pebble gray RAL 7032 and blue NCS 5030-R 80 B POSITION OVERVIEW: Item 1 Infeed and marking station with 1 side support table, adjustable 1 table as stop edge Item 2 Support roller without drive, front side in front of sheet metal table for easier feeding Item 3 Length measuring station with built-in fluorescence camera for detecting error markings Item 4 Automatic width measurement, contactless Item 5 OptiCut 304 optimizing cross-cut saw - right-hand version with built-in waste chute including equipment package for large wood cross-sections Graphic input terminal (16 x 40 characters, Numeric keypad) with software package for optimization and system control. Available for processing: - max. 16 product groups - max. 8 grades per product group - max. 200 fixed lengths per product group Item 6: Outfeed conveyor as sorting station with drive unit, length 7500 m Item 7: 2 ejectors mounted on the outfeed conveyor Storage location: Nattheim Dodpfx Aow Sy T Hsc Njki

Year of construction: 2023, condition: new, Round wooden cross conveyors heavy duty 4 line length ca. 9m Dedodzx I Ropfx Ac Nski Strand distance 1500 mm 1800 mm 2300 mm height 1500 mm

Condition: used, Year of construction: 2001, Abrasive belt length 1st unit: 2,150 mm Max. working width: 1,300 mm Number of belts: 3 Belt 1st unit: cross belt Design 1st unit: cross belt Sanding pad 1st unit: electronic segmented pad Abrasive belt width 1st unit: 150 x 4,800 mm Drive 1st unit: kW 2nd unit: longitudinal roller Design 2nd unit: steel calibration roller Abrasive belt length 2nd unit: 2,150 mm Abrasive belt width 2nd unit: 1,350 mm Abrasive belt speed 2nd unit: 18 m/sec 3rd unit: pad unit Design 3rd roller: electronic segmented pressure beam SDS system Sanding pad 3rd unit: electronic segmented, 32 mm width Abrasive belt length 3rd unit: 2,150 mm Abrasive belt width 3rd unit: 1,350 mm Suitable for lacquer sanding: yes Belt air blast: yes Vacuum conveyor: yes Feed speed, fixed: stepless 5 – 15 m/min Control: screen control Electrical/pneumatic belt oscillation: electrical Infeed height: variable (lower table moves) Table height adjustment: electric motor Table height display: digital Working height / feed table height: 880 mm Djdpfexzi S Njx Ac Neki Location: Supplier

Condition: excellent (used), Year of construction: 2007, functionality: fully functional, DIMTER OPTICUT 200 ELITE Wood dimensions to be processed: Dedpfsyrga Tsx Ac Neki Input lengths min./max. 400 - 6300 mm Input widths min./max. 30 - 260 mm Input thicknesses min./max. 12 - 80 mm Timber cross-sections max. 260 x 12MM 200 x 60mm 160 x 80mm Performance of the system: Feed speed max. 180 m/min, infinitely variable Time per cross-cutting process incl. brakes 0.7 - 1.2 s

Condition: used, Year of construction: 2012, operating hours: 926 h, total height: 1,800 mm, total length: 11,250 mm, total width: 900 mm, Weight: 1.500 kg Price: On request - Year: 2012 - Documentation available: No - CE marking present: Yes - CE certificate present: No Dsdeyna Ezopfx Ac Njki - Serial number: 546324 - Operating hours: 926 - Main motor power [kW]: 7.5 - Max. saw length [mm]: 7209 - Max. saw width [mm]: 300 - Max. saw blade diameter [mm]: 500 - Arbor saw blade diameter [mm]: 85 - Input table length [mm]: 7850 - Output table length [mm]: 2400 - Options: Automatic pusher system - Voltage [V]: 400 - Current consumption [A]: 22 - Fuse [A]: 25 - Power [kW]: 11.0 - Transport dimensions: 11250mm x 900mm x 1800mm (l x w x h) - Transport weight [kg]: 1500kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2022, total height: 1,700 mm, total length: 10,000 mm, total width: 1,800 mm, Weight: 1.100 kg Price: On request - Year: 2022 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 8737 - Max. saw length [mm]: 6000 - Max. saw width [mm]: 300 - Min. saw blade diameter[mm]: 490 - Max. saw blade diameter [mm]: 500 - Arbor saw blade diameter [mm]: 30 - Input table length [mm]: 7000 - Output table length [mm]: 2000 - Options: Automatic pusher system - Voltage [V]: 400 - Current consumption [A]: 20 - Fuse [A]: 32 - Transport dimensions: 10000mm x 1800mm x 1700mm (l x w x h) - Transport weight [kg]: 1100kg - Transport packages [pcs.]: 3 Dodpfeyna Enox Ac Noki Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: excellent (used), Year of construction: 2005, Connection values: Dodpfx Aexmhhyoc Nski Single phase, AC 50 ... 60 cycles Voltage switchable 200/220/240 V ± 10 % Power consumption: 110 W Heat emission: 95 kcal/h Application: Form depth 3…12 1/2" // Form width 148…470 mm Paper weight: Single webs 45…170 g/m2 // Multiple sets 125 ... 300 g/m2 Stack height up to ca. 300 mm The machine worked together in production with MICRO-FORMS LABELLER 18S (Sticks labels on sheets) // Ref. No.: 40016.25

Condition: new, table width: 730 mm, travel distance X-axis: 500 mm, travel distance Y-axis: 200 mm, - Table size: 730 × 210 mm Dksdpjyqwnrjfx Ac Nei - Travel (X/Y): 500 × 200 mm

Condition: excellent (used), Catalogue number 7833 TECHNICAL DATA - Max blade diameter: 400mm - Blade bore diameter: 30mm - Max cutting height: 110mm - Main blade adjustable up/down and at an angle - Blade guard included - With side carriage - Angle guide - Cutting length on carriage: 870mm - Cutting width at the fence: 600mm - Main motor approx.: 4kW - Table dimensions: 900x1020mm - Extraction port diameter: 110mm - Overall dimensions (L/W/H): 2500x1400x1000mm - Weight: 530kg ADVANTAGES – Polish manufacture – Includes side carriage – DTR technical documentation – Used saw, very good condition Dkjdpfxjx Arime Ac Nei Net price: 7500 PLN Net price: 1790 EUR based on 4.2 EUR exchange rate (Prices may change with significant fluctuations)

Condition: used, Year of construction: 2010, functionality: fully functional, machine/vehicle number: 467334, Manufacture year 2010 Machine specifications: - Push infeed, max. length 6300 mm - Automatic length measuring and chalk reader - Cutting width 40 – 420 mm - Cutting height 15 – 170 mm - Min. cross section 20 x 10 mm - Max. cross section 270 x 170 / 410 x 30 mm - Motor 13.5 kW - Total electrical load approx. 22 kW Dkedpfx Acjypvdij Nsi -Operating pressure approx. 8 bar - Saw blade diameter 630 mm / bore 30 mm Consisting of: 1. Cross chain infeed system 8 pc. chain transport with 3 latch rows 2. Push infeed system with liftable pusher Infeed length 6300 mm, length detecting and chalk reader 3. OptiCom Direct controller 4. Opticut cross cut saw unit S90 XL With side pusher and waste gate 5. Outfeed transport belt

Condition: used, Year of construction: 2000, functionality: unexamined, input voltage: 400 V, type of input current: three-phase, saw blade diameter: 500 mm, rotational speed (max.): 2,850 rpm, rotational speed (min.): 2,850 rpm, air pressure: 6 bar, pressure: 6 bar, saw blade speed: 2,850 rpm, We are offering this used Haffner DGS 187 double mitre saw, year 2000, including 2 new saw blades. Type: DGS 187 Serial number: 0103 Voltage: 400 V Frequency: 50 Hz Current: 20 A Operating pressure: 6 bar Air consumption per cycle: 8.0 l Dkjdpfoyn U Azex Ac Noi Max. saw blade Ø: 500 mm Speed: 2850 rpm If you have any questions or require more information, please feel free to send us a message or give us a call.

Year of construction: 1991, condition: used, The Filtrox Cross Flow microfilter works with a permissible transmembrane pressure of 6 bar (0 °C - 95 °C) and a filtrate volume of 4.5 - 7 hl/h with a filter surface area of 26.4 m². Two pumps (20 kW) in the unfiltrate circuit transport the medium to be filtered. With 16 hl agitator tank as cleaning tank. Additional title: yeast-beer recovery Capacity: 7 hl/h Tol. operating pressure: 10 bar Tol. operating temperature: 85 °C Max. filter area: 26 m^2 Current: 4,85/2,8 A Voltage: 220/380 V Frequency: 50 Hz Operation / Control: Simatic S5 Features: 8 ceramic membrane modules (total filtration area 26.4 m2); high-pressure pump; 16 hl cleaning tank with agitator; various pipes, valves, measurement and control technology Dsdovcq Daopfx Ac Noki

Condition: like new (used), Year of construction: 2023, functionality: fully functional, operating hours: 5 h, power: 5 kW (6.80 HP), input voltage: 400 V, pivoting range: 45 °, rotational speed (max.): 10,000 rpm, rotational speed (min.): 3,500 rpm, table width: 530 mm, table length: 1,200 mm, overall weight: 510 kg, tool diameter: 240 mm, Equipment: CE marking, Professional woodworking machine with tilting milling spindle and cantilever arm. Exhibition machine like new - used only for demonstration purposes Milling unit made from cast iron, tiltable up to -45° backwards Four milling speeds from 3500 to 10000 rpm Forward and reverse rotation Height and tilt display accurate to 0.1 mm Quick speed change via eccentric clamping Powerful 5.0 kW industrial motor Curved milling hood included Made in Italy Milling spindle tilt 0 – -45° Usable spindle length 125 mm Spindle speeds 3500/6000/8000/10000 rpm Speed indication via LED display on the front panel Spindle shaft diameter 30 mm Max. tool diameter 240 mm Max. retractable tool diameter 230 mm Dksdeyn Ny Uspfx Ac Nei Max. tenoning tool diameter 320 mm Accessories included: Mitre fence with two flip stops Eccentric clamp Curved milling safety guard Additionally, adjustable system fence jaws The machine can be inspected and tested at any time at the Chemnitz location.

Condition: good (used), Year of construction: 1994, Automatic defect cross-cut system Wood width max. 260 mm Wood height max. 100 mm Dkjdpfx Acokv Unte Noi Saw 7.5 kW Feed 6 kW worked 1995 - 2012 approx. 4 hours/day