Used Kf 65 for sale (8,119)

Condition: used, functionality: unexamined, For sale is a Leybold RUTA vacuum pump unit in adapter configuration, consisting of a RUVAC WS 501 rotary lobe pump and a TRIVAC D 65 B rotary vane pre-pump. Technical data and markings: - Configuration: RUVAC WS 501 / TRIVAC D 65 B / Adapter - RUVAC catalog number: 11732 - RUVAC nominal pumping speed: 505 m³/h - TRIVAC D 65 B, catalog number 11296 Bledpfxszzr Nks Amren - TRIVAC serial number: 31000491088 - TRIVAC pumping speed: 65 m³/h - Pumping speed of the pump unit at 0.1 mbar: approx. 380 m³/h - Ultimate partial pressure: < 2 × 10⁻⁵ mbar - Installed motor power: approx. 4.4 kW - Connections: DN 63 ISO-K on the suction side, DN 40 ISO-KF on the discharge side - Druschke article number: SGWS501 - Druschke serial/ID number: 11732-ID15931 - RUVAC marking 2003/08; TRIVAC marking CW 31/2011 Visible scope of supply according to the images: - RUVAC WS 501 - TRIVAC D 65 B - Direct adapter - Side filter/separator housing - Connection line, cable, and plug - Base frame with drip tray Used condition with dirt, paint damage, and slight corrosion. The operational condition and achievable vacuum performance were not re-tested after disassembly; therefore, it is sold as untested. A control cabinet or frequency inverter is not shown and is not part of the described scope of supply. Scope of supply according to the images. Price net, EXW Kirkel. Loading and organization of transport are possible for an additional charge and by prior agreement. The transport costs depend on the destination and scope. Sale subject to prior sale.

Condition: excellent (used), Year of construction: 1991, functionality: fully functional, throat depth: 455 mm, total width: 860 mm, total length: 2,000 mm, total height: 2,050 mm, sheet thickness aluminum (max.): 8 mm, overall weight: 2,000 kg, sheet thickness steel (max.): 4 mm, Number of strokes 150 / 300 / 600 Min. Maximum sheet thickness 6 mm Horizontal troath 675 mm Vertical troath 455 mm Max. thickness Stainles 4 mm Max. thickness Aluminium 8 mm Motorised ram adjustment 0 - 80 Bsdpfxezxf Eye Amrsln Power 4.5 kW Dimensions (Estimate) Length 2000 mm Width 860 mm Height 2050 mm Weight 2000 kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Year of construction: 1963, condition: ready for operation (used), Max. forming force: 80t, connected load: 3.5kW, current type: 3 phases, frequency: 50Hz, operating voltage: 380V, control voltage: 24V, rated current of the machine: 10A, rated current of the supply fuse fast-blow: 25A, slow-blow: 15A, weight: 1.79t. With documentation, without accessories or spare parts. Regularly maintained, machine has a defect, the speed adjustment no longer functions fully. An on-site inspection is possible. Bedpjy A Smbjfx Amrjln

Condition: used, Year of construction: 2020, Format: 0x0 Equipment: Hugo Beck Flexo X Intermittent Film Packaging Machine Product Feed:Manual as a standalone machine / Automatic in-line (flexible configuration) Control System:Touchscreen with temperature memory and reproducible format settings Film Processing:PE, PO, bio-films, center-folded film, and flat film Sealing System:Side sealing + intermittent cross-sealing Operation:Intermittent Kallfass Compact 650 D Shrink Tunnel Type:High-performance energy-saving shrink tunnel Heating System:Patented ring nozzle heating system in double design Blower:Frequency-controlled, Zolltornado-style Zoll hot air flow for uniform shrinking Transport:Maintenance-free plastic modular belt, continuously adjustable speed Bodpfx Amszpgh Dsroln Film Compatibility:All polyolefin films Safety:Safety equipment according to EC directive EN 60204

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, Mafell Elektronik handheld router LO 65 Ec with Arunda 80N Maxi and LO-FA router adapter used, from business liquidation Woodworking machine with fine adjustment for routing depth for delicate work, as well as template applications in solid wood Bledpoz H Up Isfx Amron Technical data according to the manufacturer: Mafell handheld router Type: LO 65 Ec Year of manufacture: 2021 Routing depth: 0 - 65 mm Universal motor: 230 V Tool holder (mm): 1/2" / 6 - 12 mm Design: MidiMAX in T-MAX Weight: 6.9 kg Idle speed: 10000 - 22000 1/min Power: 2600 W additional accessories, as shown in the picture: Mafell Arunda 80 N router template, year of manufacture 2022 Mafell LO-FA router adapter Copy ring ø 27mm Dust extraction hood We recommend an inspection to avoid misunderstandings. Information provided without warranty Information, details, and technical data from the manufacturer To prevent any misunderstandings regarding the item's condition and the scope of the auction, we generally recommend an inspection BEFORE placing a bid! Further technical data can be requested from the manufacturer. Our business hours are from Monday to Friday between 8:30 am and 12:00 pm and 1:00 pm to 4:30 pm. During this time, inspections and collections are possible and desired, AFTER prior appointment. Subject to prior sale, changes, errors and printing errors.

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, spindle speed (max.): 6,000 rpm, bar passage: 65 mm, Equipment: bar feeder, chip conveyor, TECHNICAL DETAILS Tool turret Number of turrets: 3 Tool holder: VDI 25 W-gear Main and counter spindle Main and counter spindle speed: up to 6,000 rpm Bar diameter: 65 mm MACHINE DETAILS Coolant tank: 600 l Coolant pressure: 8 / 18 bar EQUIPMENT Gantry removal device Hainbuch HS Axzug / GS Axfix Chip conveyor Coolant tank with strainer basket Blodpfxoz Ibf Ej Amron Coolant pump Coolant cooling unit FMB Turbo 10-65, 3-meter bar feeder

Condition: ready for operation (used), functionality: fully functional, overall weight: 1,900 kg, Equipment: documentation/manual, ECKOLD KF 653 C / Power Former & Various Tools / Sets -Reach - Horizontal approx. 600mm -Reach - Vertical approx. 480mm -Working stroke 8mm -Formable sheet metal thicknesses: Steel (Steel N/mm2) max. 6mm Aluminum (250 N/mm2) 8mm Stainless steel (600 N/mm2) 4mm -Ram adjustment approx. 80mm -Foot switch -Tools (SEE PICTURES) -Sheet metal forming tool description & spare parts lists -Documentation Bedpfx Amoz Azrworoln Dimensions: L x W x H 1.6 x 0.7 x 1.9 meters / Weight 1900 kg Errors and omissions excepted.

Condition: used, Year of construction: 2017, functionality: fully functional, machine/vehicle number: 13341-T, total width: 1,420 mm, total length: 1,576 mm, total height: 1,100 mm, overall weight: 2,000 kg, cooling capacity: 20 kW (27.19 HP), input voltage: 400 V, input current: 32 A, type of input current: three-phase, input frequency: 50 Hz, operating pressure: 10 bar, space requirement length: 1,800 mm, space requirement height: 1,800 mm, space requirement width: 1,500 mm, coolant tank capacity: 800 l, Equipment: cooling unit, The system was taken out of service a year ago due to a switch to a centralized system. One year before decommissioning, all TCF elements were replaced. We can provide support for recommissioning. Bsdpjzxhcnefx Amrjln Technical data: - Total filter capacity approximately 210 l/min - Filter fineness approximately 3 μm nominal - Tank capacity approximately 800 l - Designed for two hoppers WU305L/325L/105L including interface Equipment: - 3 filter groups, individually automatically backwashable, each with 2 TCF filter columns - 1 filter pump - 1 pneumatic unit - 1 automatic sludge treatment system via a settling tank and scraper conveyor - In-line cooling via the return flow from the filter columns to the clean oil area via the plate heat exchanger, including flow control in the chilled water circuit - Color RAL 7035 - 1 control cabinet, wired according to VDE standards, PLC control, operation and parameterization via touch panel 2 pcs. machine supply pump for supplying the machine with filtered coolant as a submersible centrifugal pump Technical data: - Flow rate: approximately 100 l/min - Delivery pressure: approximately 10 bar - Drive: 400V, 50Hz 2 pcs. drive cooling pump as a submersible centrifugal pump Technical data: - Flow rate: approximately 30 l/min - Delivery pressure: approximately 6 bar - Drive: 400V, 50Hz 1 pcs. screwed plate heat exchanger with cooling control approximately 20kW Designed for cooling water 70 l/min, 13°C supply temperature.

Condition: used, Year of construction: 2007, machine/vehicle number: 4801250 / PH06 11 005, functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, overall weight: 55,000 kg, year of last overhaul: 2024, clamping force: 3,000 kN, mold height (min.): 1,000 mm, plate length: 2,800 mm, plate width: 2,200 mm, Equipment: CE marking, documentation/manual, For sale is a KraussMaffei LFI shuttle mould carrier for polyurethane processing and backfoaming of large-format components. Bljdpoz Dn Ixsfx Amron The system was designed for PU moulding and LFI applications and features a hydraulic clamping unit with a movable lower mould mounting platen. Technical data: Manufacturer: KraussMaffei Type: FT-R-H-25-20-3600.0°.65° Year of manufacture: 2007 KM order number: 39000233 Control system: Siemens S7 Clamping force: 3,000 kN Opening force: 800 kN Parallel stroke: 600 mm Mould mounting platens: 2,500 x 2,000 mm Minimum mould height: 1,000 mm Maximum mould height: 1,500 mm Maximum total mould weight: 10,000 kg Maximum upper mould weight: 5,000 kg Upper mould mounting platen pivotable up to 90° Machine weight: approx. 55,000 kg Operating voltage: 400 V Scope of supply: LFI shuttle mould carrier Hydraulic units Control unit Shuttle / traversing unit Production moulds and temperature control units are not included in the scope of supply. Extensive original KraussMaffei documentation is available, including operating manuals, technical drawings, electrical diagrams and spare parts documentation. The machine is fully functional. Inspection under power is possible by prior appointment. The machine is located in the Hamburg area, Northern Germany. The exact location will be provided to qualified prospective buyers. Dismantling, loading and transport are to be carried out by the buyer. Further technical documentation, drawings and photographs are available upon request. Subject to availability.

Condition: ready for operation (used), Year of construction: 2013, operating hours: 7,358 h, functionality: fully functional, machine/vehicle number: 6LUD00036, travel distance X-axis: 620 mm, travel distance Y-axis: 520 mm, travel distance Z-axis: 460 mm, feed length X-axis: 620 mm, feed length Y-axis: 620 mm, feed length Z-axis: 460 mm, feed rate X-axis: 36,000 m/min, feed rate Y-axis: 36,000 m/min, feed rate Z-axis: 36,000 m/min, torque: 108 Nm, controller manufacturer: Heidenhain, controller model: iTNC530, workpiece length (max.): 500 mm, workpiece width (max.): 400 mm, workpiece height (max.): 350 mm, workpiece diameter (max.): 680 mm, workpiece weight (max.): 300 kg, total height: 3,400 mm, total length: 4,600 mm, total width: 2,700 mm, table width: 600 mm, table height: 755 mm, table length: 600 mm, table load: 300 kg, rotary table diameter: 600 mm, rotational speed (min.): 20 rpm, rotational speed (max.): 12,000 rpm, overall weight: 8,500 kg, spindle speed (min.): 20 rpm, spindle speed (max.): 12,000 rpm, operating hours of spindle: 5,303 h, coolant supply: 18 bar, distance table center to spindle nose: 50 mm, spindle motor power: 17,000 W, spindle nose: SK40, number of spindles: 1, number of slots in tool magazine: 100, input voltage: 400 V, type of input current: three-phase, Equipment: chip conveyor, documentation/manual, Commissioned 4/2014 Table rotation, C-axis: 360° Table swivel, B-axis: -50° to +110° Distance from spindle nose to table: 150 mm Table clamping surface: Ø 650 Table load capacity, max.: 300 kg Table slots: 5 x 18H7 x 100 mm Centering bore: Ø 50 H7 x 30 mm Workpiece size, max.: Ø 520 x 330 mm Machine accuracy: VDI I DGQ 3441* Positioning accuracy: +/- 0.006 mm* Axis resolution: 0.001 mm* *determined at a constant ambient temperature of 20°C +/- 1°C Main spindle: Main drive, AC motor, direct drive Drive power (100% / 25% ED): 10.0 / 17.0 kW Speed range, stepless: 20 - 12000 rpm Spindle taper: SK 40 DIN 69871 Torque at (100% / ED): 63.7 / 108.6 Nm Axis drives: Axes X, Y, Z: AC motors Axes B, C: AC motors Travel speeds: Rapid traverse in axes X, Y, Z: 36 m/min Speed, max. B-axis: 25 rpm Speed, max. C-axis: 25 rpm Acceleration X, Y, Z: 6.5 m/s² Coolant system: External tool cooling via external nozzles Coolant tank: 280 l Operating pressure, external: 0.9 bar Coolant system, internal tool cooling DIN 69871 Form A Blsdpsz Diq Uefx Amron Operating pressure, internal coolant supply: 18.0 bar Manual rinsing of the work area via an additional gun Standard accessories: - CNC control: Heidenhain iTNC 530, full simultaneous 5-axis version - Handwheel 410 (Heidenhain) - Digital axis drives - Digital spindle drive - Swarf conveyor with discharge height 800 mm • Spindle cooling – radiators – plate cooling for spindle motor - Full protective enclosure with cabin roof Tool magazine VZG 65 5A by Indunorm: Number of tools: 100, with a tool length of up to 320 mm / can be converted to 125 tools, then a tool length of only 200 mm is possible. Tool diameter, max.: 80 mm Tool diameter, max.: 130 mm (with free adjacent positions) Tool change with double gripper - Linear path measuring system in axes X / Y / Z (glass scale) - Direct encoder in axes B / C - Temperature compensation - IR measuring probe – 3D Software - Option - iTNC 530 Kinematic-Opt • Calibration software Internal tool cooling 18 bar • Coolant tank • Internal tool cooling: 280 L DIN 69871 Form A • Double-circuit filter • Switchable filter cartridges • Filtration rate: 10 µm Band filter system PRODUCTION - LINE - RT 100 Automatic pallet changing system Loading and unloading via a linear axis system: Handling data: Handling weight, max.: 100 kg (35 kg) Pallet capacity: 6 pallet positions up to 400 x 400 mm: Control: PLC control with integrated control cabinet incl. switching and control components incl. software for the automatic sequence Zero point clamping system 320 x 320 x 60 mm - Clamping via 4 clamping bolts - Axis distance: 180 mm - Clamping force: 4 x 12500 N - Repeatability: 0.005 mm - Axial load, max.: 4000 kg • Zero point clamping plate 320 x 320 - Automatic door Interface for automation and clamping systems Universal interface for automatic pallet changing systems, force clamping devices and zero point clamping systems • for pneumatic clamping systems • 2-channel rotary feedthrough integrated in the table • Pneumatic lines led to the outside • Pneumatic maintenance unit • Control via M commands logical inputs and outputs prepared incl. 7 pallets 320x320 with 6 vices and one 3-jaw chuck !!without tool holders and without tools!! Machine ex works, without delivery and assembly, all information without guarantee, price plus statutory value-added tax.

Condition: excellent (used), Year of construction: 2019, 1.0 unit, two-component dispensing system with material feed and mixer. Bljdpfsz Hn Ecsx Amren Manufacturer: KOCH - Technik Type: GK-65 / 612D / GK65 / Year of manufacture: 2019

Condition: used, Year of construction: 1998, operating hours: 97,593 h, functionality: fully functional, turning diameter: 65 mm, spindle bore: 79 mm, spindle speed (max.): 4,500 rpm, spindle speed (min.): 25 rpm, For Sale: Gildemeister MF Sprint 65 CNC Sliding Headstock Lathe with 3-Meter Bar Feeder, as shown in the pictures. The machine was removed from our workshop in fully functional condition. A video of the machine in operation prior to disassembly is available upon request. Approximately five years ago, the linear guides of the X1 and Z1 slides (on the main spindle side) were replaced, including bearings and belts. A new HMI interface was installed recently. Detailed specifications and technical data can be found in the attached PDF. TECHNICAL DATA Control: Sinumerik 840C Bar Feeder: SIMAG 65.1-3200G, Year of Manufacture: 1998 Bar Length: 3 meters Bar Diameter / Spindle Bore: 65 mm Main Drive Bljdpfxewym Nfj Amrjn Power Output: 28 / 21 kW Speed Range: 25 – 4,500 rpm Torque: 320 / 240 Nm Maximum Feed Rate for Thread Cutting: 10 m/min C-Axis Speed: 120 rpm C-Axis Torque (Holding Torque): 180 Nm Tool Carrier Number of Tool Stations: 8 Shank Diameter (DIN 69880): 30 mm Number of Driven Tool Stations: 4 Power Output: 7.6 / 4.6 kW Torque: 24 / 14.7 Nm Maximum Speed of Tool Carrier 1: 4,000 rpm Maximum Speed of Tool Carrier 2: 4,000 rpm Slide 1 Cross Travel / Longitudinal Travel: 155 / 280 mm Rapid Traverse Speed X/Z: 22.5 / 22.5 m/min Feed Force X/Z: 900 / 900 daN Slide 2 Cross Travel / Longitudinal Travel: 82 / 120 mm Rapid Traverse Speed X/Z: 22.5 / 22.5 m/min Feed Force X/Z: 900 / 900 daN MACHINE DATA Dimensions with Bar Feeder and Chip Conveyor (L × W × H): approx. 6 × 2 × 2 meters Weight: approx. 6.5 tons Operating Voltage: 50 Hz, 400 V Accessories: Cooling System Chip Conveyor Documentation The offer is subject to change and non-binding, changes and errors in the technical data or the equipment, as well as prior sale reserved Used machines are purchased as seen, without warranty claims. Delivery ex works excluding packaging and insurance, unless otherwise agreed. The price does not include statutory value added tax. As is usual with used machines, payment is made before loading.

Condition: used, Year of construction: 1999, operating hours: 72,805 h, functionality: fully functional, spindle bore: 65 mm, total length: 3,074 mm, total width: 1,941 mm, type of input current: three-phase, overall weight: 4,000 kg, spindle nose: Kk6, Equipment: documentation/manual, We are offering this used EMCO EMCOTURN 365/65 CNC lathe, manufactured in 1999. Blodjzzrwhopfx Amren Model: EMCOTURN 365/65 Supply voltage: 400 V Phases: 3/PE Frequency: 50/60 Hz Maximum current Imax: 59 A Rated current Im: 27 A Short-circuit current Ik: 6 kA Duty cycle S6: 40% Year of manufacture: 1999 If you have any questions or require further information, please feel free to send us a message or call us.

Condition: ready for operation (used), Year of construction: 1984, Deckel Copy Milling Machine Model KF 3 S Bsdpfx Aez Hu Abomroln Year of manufacture: 1984 Table surfaces: 600 x 555 / 620 x 750 mm Y-axis travel: 150 mm Z-axis stroke: 380 mm X-axis stroke: 150 mm Drive: 3 kW Roughing spindle Finishing spindle Locking arm Control lever with cable Tracing stylus holder Collets Weight: 2400 kg Price: EUR 2,000—plus VAT, ex works

Condition: refurbished (used), Year of construction: 2027, functionality: fully functional, gear diameter: 250 mm, spindle speed (max.): 71 rpm, spindle speed (min.): 35 rpm, total height: 1,800 mm, total length: 2,200 mm, total width: 1,800 mm, controller manufacturer: Siemens Sinumerik ONE, drive type: Sinamics S120, control type: CNC control, Equipment: rotational speed infinitely variable, Economical production of straight-toothed bevel gears – both in single units and in series: The SW KF 250 is based on the proven cast iron bed of the Chemnitzer Modul ZFTK 250 and is completely rebuilt by Serwema Retrofit Solutions, with Siemens Sinumerik ONE, digital Sinamics S120 drives, and an electronic worm gear between the workpiece and weighing drive. The machine mills using the convoid process, a universal and highly economical process for straight-toothed bevel gears, as well as producing herringbone gears and spur couplings. Application areas: agricultural machinery, gearbox construction, drive technology, railways and mining – anywhere where straight-toothed bevel gears up to 250 mm are required and new machines are hardly offered. Delivery time is five to six months from order, with acceptance testing in Chemnitz together with you. The SerWeMa gear cutting software guides the operator through workpiece and tool data using masks, without the need for programming. Integrated technology cycles: plunging, rolling, plunging and rolling, and plunging with double rollers. Engagement angles from 14 to 28° can be freely selected, and the number of teeth can range from 6 to 100. The stiff, ribbed cast iron bed provides the static and dynamic rigidity for bevel gears up to module 7 with a tooth width of 40 mm; the hydraulic and coolant unit is integrated into the bed, with components from Rexroth, Parker and Hydac, and pulse lubrication from Bielomatik. All worm gears are newly manufactured in bronze. Blsdpfx Amjz E H Dberjn Technical data: max. bevel gear diameter 250 mm, max. module 7, number of teeth 6–100, max. tooth width 40 mm, engagement angle 14–28°, distance between workpiece spindle and bevel tip 40–280 mm, workpiece spindle mount 80 mm metric, cutter head diameter 355 mm with 22 cutters per side, cutter head speed 35–71 rpm, connection value 30 kVA. Installation dimensions approx. 2.5 × 2.1 × 1.9 m, weight approx. 6 t. Scope of supply: complete electrical equipment with Siemens Sinumerik ONE and Sinamics S120, climate-controlled control cabinet manufactured in-house, dialog software, all worm gears in bronze, magnetic chip conveyor, circulation and pulse lubrication, hydraulic unit, coolant system, new paint RAL 5015/7035, geometric acceptance test according to SerWeMa protocol based on DIN standards, documentation (operating manual, electrical diagrams with parts lists, hydraulic and lubrication diagram), CE marking. Optional: installation, commissioning and operator training at your site.

Condition: used, Year of construction: 2016, controller manufacturer: Mitsubishi, controller model: TX8i-s, _____ Description: Year of manuf. : 2016 Control : Mitsubishi TX8i-s Mainspindle: Technology:Motorspindle Speed:5.000 rpm Power (max.):35 kW Torque (max.):120 Nm Barcapacity:65 mm Workpiececlamping:Hainbuch Spanntop Kombi Axfix Gr. 65 Subspindle: Technology:Motor spindle, integrated in tool carrier II Speed:7.000 rpm :Power (max.):12 kW Torque (max.):22,5 Nm Chuck:Hainbuch Spanntop Kombi Axfix Gr. 42 Toolcarrier I (X/Y/Z): Technology:Turret with 10 stations Taper:Traub ø45 mm Tooldrive:12.000 rpm, 10 kW, 8 Nm Movement in X/Y/Z:140/100/300 mm Toolcarrier II (X/Y/Z): Technology:Turret with 9 stations Taper:Traub ø45 mm Tooldrive:12.000 rpm, 10 kW, 8 Nm Movement in X/Y/Z:140/100/300 mm Backworking attachment: Technology:Backworking attachment with 8 stations (2x synchron, 6x asynchron) Driven Tools:5 stations Tooldrive:12.000 U/min, 6,7 kW, 5,3 Nm Equipment/Accessory: Bsdpfxsz A Nz De Amreln Positionsensor:Direct Scales in X (up/down) Chipmanagement:Chip conveyor Coolingmanagement:Internal cooling unit with Paperbaletfilter and High-pressure, 80 bar Coolanttemperaturecontrol:Interface for external chiller prepared, Deltatherm Wasteheatmanagement:Interface for external chiller prepared Rawmaterialfeed:Barloader, FMB SL 80 V Finished part removal:Unloading device (NC-controlled) with coneyor belt Fireextinguishing unit:Kraft + Bauer Oilmistseparation:Electrostatic extraction LTA AC 3001 Further Accessory:Misc. used static and driven Toolholder

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, CNC machining center Hedelius Forte 65 Single 1320 Control system: Heidenhain TNC 640 Year of manufacture: 2019 Availability: in transit Internal machine number: 74 Travel distances: X-axis 1,320 mm Y-axis 650 mm Z-axis 600 mm Total clamping area: 1,500 x 650 mm Table load: approx. 1,200 kg Tool holder: HSK 63 Bljdpfx Ajzzmiremrjn Tool magazine: 65 positions Spindle speed: 18,000 rpm Drive power: 35 kW Equipment: - Inclined bed coolant system, 900 l - Internal cooling lubricant system, 25 bar - Chip conveyor - 1x flushing gun - Electronic handwheel

Condition: excellent (used), Year of construction: 2008, machine/vehicle number: 1780021272, functionality: fully functional, 3 spindle copy router elumatec KF 178/00 Top routing unit: Cutting range using stops or copy templates 340 x 100 mm Travel 110 mm Bottom routing unit: Cutting range using stops or copy templates 240 x 85 mm Travel at front 95 mm Bljdozy Staepfx Amren Travel at back 45 mm Spindle speed 12,000 rpm Clamping range for profiles 115 x 100 mm Power supply 230/400 V, 3~, 50 Hz Power output per motor 0.74 kW Cobtjzmn N Reiaf Smorg Compressed air supply 7 bar Air consumption per working cycle 12 l without spraying, 24 l with spraying Length 980 mm, depth 1,250 mm, height 1,610 mm, weight 360 kg We can ship the machine to your address.

Condition: used, Year of construction: 2003, Capacity: up to 25.000 l/h Blodpfez Iclmox Amrsn

Condition: good (used), Year of construction: 2019, Universal machining center Machine type: Hedelius Acura 65 Control: Heidenhain TNC 640 Year: 2019 Available after: Dezember 2026 SPECIFICATIONS 5-axis-simultaneous X-Axis: 700 mm Y-Axis: 650 / 465 mm Z-Axis: 600 mm Rapid motion: (X/Y/Z): 40/40/40 m/min. B-Axes: +30° / -115° Spindle speeds: 12.000 rpm Spindle power: 22 kW Torque: 117 Nm Tool: SK 40 Tool capacity: 65 Table size: D: 650 x 540 mm mm Max. Table Load: 500 kg Equipment Chip conveyor 3D-Touch probe: M&H Internal cooling: 25 bar Cooling tank: 500 l Bedsz D Aq Uepfx Amrsln Electronical handwheel: HR 510 Oil mist separator Chip rinsing pistol Kinematikset 3D-Formenbauabstimmung Documentation - German

Year of construction: 1974, condition: used, functionality: unexamined, For sale: - Circular saw mill, type OS65, from a carpentry/lumber mill in very good condition. - Low operating hours, only approx. 800-1000 m³/year. - Clamping carriage, self-propelled. - Auxiliary carriage. - Approx. 15m of guide rails for the clamping carriage/auxiliary carriage. Blsdpez Dn Ulefx Amren - Splitting wedge/outfeed rollers, not driven. - €20,000 net / plus VAT. The following are also available separately: - Log infeed system - Chain hoist with transverse conveyor Prior inspection is required.

Condition: used, Year of construction: 2015, Base machine T65C Automatic, 1 unit General technical features: • Weight: 1600-2,200 kg, Martin composite stand • Table size: 860 mm x 1370 mm in gray cast iron; table extension is standard, designed as a lockable tool tray, 335 mm x 625 mm • Table height: 900 mm • Scoring table: Standard length 3000 mm, table length corresponds to cutting length; position-independent locking; guides are hardened, wear-resistant, self-cleaning; table lip is replaceable; design in anodized aluminum • Saw blade spindle: Ø 30 mm for main saw blade, two drive pins 8 mm • Saw blade change: Quick-change system "ProLock" • Saw blade diameter: Ø 250 - 550 mm; can be recessed under the table up to 400 mm; saw blades up to Ø 400 mm can be used with inserted scoring saw blades • Cutting width: 1,100 mm • Saw blade swivel: 0° to +46° • Cutting height: max. 204 mm / saw blade 550 mm / 0°, max. 135 mm / saw blade 550 mm / +45° • Cutting width (main saw): Saw blades with max. 6 mm cutting width at swivel angle 0° to +46°; special tools with max. 20 mm cutting width at swivel angle 0° • Motor power: 5.5 kW (7.5 hp), 3 ~ / 400 V - 50 Hz • Speeds: 2800 / 4000 / 5000 rpm; easy and convenient speed change from the front via the chip guard • Length stop: Design in anodized aluminum with continuous support, fine adjustment for both fence elements; dimension display via a scale with a magnifying glass; length compensation for angled cuts with electronic assistance; cutting length 95 - 2000 mm, extendable up to 3220 mm • Cross table: Design in zinc-coated steel; angled cuts according to the scale without repositioning the stop; integrated fixing positions for 0°, 22.5°, 30° and 45° cuts, one-hand clamping on the scoring table; support dimensions 1340 x 650 mm • Parallel stop: Electromotive positioning of the parallel stop; stop bar in anodized aluminum, foldable; complete integration of the parallel stop into the control system; guided by four grooved ball bearings, floating above the machine table, removable in any position; movement of the stop in the safety area (0 - 200 mm) in hold mode, display resolution: 0.1 mm; repeat accuracy ± 0.05 mm • Extraction: Connection to protective hood Ø 100 mm, machine stand Ø 120 mm; minimum extraction air volume: 23 m³/min at 800 Pa at the main connection 120 mm • Protective hood: Protective hood with 2 blade sets (1x flat for 0° cuts, 1x with a one-sided belly for cuts 0° to 46°); passage dimension between saw blade axis and support column: approx. 900 mm, clearance when the hood is swiveled away between the saw blade and the protective hood arm: approx. 635 mm; releasing the locking from the working position • Standard accessories: 1 scoring shoe on the scoring table, 1 handle for pushing the wood, 1 ProLock combination wrench, 1 return handle, 4 shims (250/350, 350/450, 450/500, 500/550), 1 push stick • Control panel: Control panel at eye level, can be swiveled away • Electrical equipment (according to VDE/EN 60204): Electronic soft start/stop device for the main saw blade; contact for controlling the extraction; motor protection switch and winding protection, emergency stop button; required voltage supply: 3 ~ / 400 V - 50 Hz Bledpoz Alfuofx Amren • Emission values, workplace emission: Noise values according to DIN EN ISO 11202, dust values according to DIN 33893. Please refer to the operating manual for the technical values. Performance features of the T65 control system: Performance features of the 5.7" (145 mm) touch screen control system with color L

Condition: used, Year of construction: 2000, machine/vehicle number: 690-264, Machine: KRONES KGW-65-S-E Crate washer Blodpfx Ajz Icnzemron

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, 5-axis machining center Hedelius ACURA 65 Control system: TNC 640 Year of manufacture: 2017 Internal machine number: 72 Travel ranges: X-axis: 700 mm Y-axis H / V: 650 / 465 mm Z-axis: 600 mm Rotary tilting table: Ø 650 x 540 mm Tilting range: +30° to -115° Interference circle diameter: Ø 700 mm Table load: 500 kg Tool holder: DIN 69893-1 HSK-A63 Tool magazine: 65 stations Spindle speed: 50 - 18,000 rpm ZeroClamp, 4-fold 3D measuring probe M&H 25.50 5-axis simultaneous machining ACURA Handheld control unit HR 250 3D mold making alignment ACURA Bedpfxjzwuq Nj Amroln KinematicsOpt TNC640 Collision monitoring ACURA/TNC Compressed air at the spindle head Coolant system 1250l, 25 bar Chip conveyor Exhaust filter Laser light curtain for tools ACURA

Condition: good (used), Year of construction: 2010, total width: 680 mm, total length: 1,250 mm, total height: 1,740 mm, sheet thickness aluminum (max.): 2 mm, overall weight: 505 kg, sheet thickness steel (max.): 1 mm, Eckold Kraftformers Piccolo ECKOLD - KF 324 MACH-ID 9815 Make: ECKOLD Type: KF 324 YOP: 2010 Eckold Kraftformer; motorised machine for Shrinking, Stretching, Doming, Planishing, Reforming, Flattening, Straightening For Aircraft production and Maintenance. For Car body shop specialists For Artisans and Craftmen Equipped with tool storage shelf in side column Machine equipped for tooling: FWR 402S FWA 403S   Number of strokes: 400Min. Maximum sheet thickness: 2.0mm Horizontal troath: 340mm Vertical troath: 235mm Max. thickness Stainles: 1.5mm Blodpfxjz Ha Ips Amren Max. thickness Aluminium: 2.5mm Manuel / Hand ram adjustment:32 Power: 1.5kW Length: 1250mm Width: 680mm Height: 1740mm Weight: 505kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!