Used Automatic Punching Press for sale (34,152)

Condition: used, Year of construction: 1974, Technical details: pressure: 30 t ram surface area: 450x250 mm ram adjustment: max. 50 (manual) mm strokes per minute: 20 - 120 stroke: ca./approx. 20 mm mm adjustment of stroke: nein/ no stroke adj. mm dayligth: Arbeitsraum: 220 - 280 mm Table surface area useable: 600 x 600 mm total power requirement: 7,5 kW weight of the machine ca.: 5,0 t dimensions L x W x H: Maschine: 1,8 x 1,2 x 2,7 m Dimensions (LxWxH): Schaltschrank: 0,92 x 0,46 x 1,4 m Automatic punching press 4 columns mechanical with feed unit with control panel Dodpou Icx Refx Albskt passage widths: Column opening front=350mm and side=258mm *

Condition: used, Die-cutting machine – Swivel frame die-cutting machine – Flatbed die-cutting machine – Toggle press – Eccentric press Die-cutting machine + feeder for use with strip-type die-cutting tools Flatbed die-cutting machine HELMERDING, type PSH 25 Item no. EP 97784, Machine no. 6073, Year of manufacture 1998 Pressing force 25 tons Distance between tie rods 700 mm Table area = installation space 800 x 670 mm Table area = installation frame, width 510 x depth 440 mm, plate thickness 20 mm Dodpfxsdzqmzs Albjkt Punch area 800 x 670 mm Through-hole in the table 490 x 420 mm Punch stroke 45 mm Punch adjustment distance 10 mm Installation height = tool height 100 mm Stroke rate up to 250 strokes/min Motor power 15 kW Mains connection 400 volts, 50 Hz - controlled drive for stepless stroke rate adjustment - pneumatic clutch-brake combination - punch equalizing cylinder - automatic central lubrication system VOGEL - massive base plate with 4 vibration damping elements under the machine Space requirement L x W x H approx. 3000 x 2000 x 3000 mm Weight 4.5 tons Good condition Previously, the machine was used for die-cutting cardboard sheets. Ideal for die-cutting non-woven fabrics or similar materials for respiratory masks.

Condition: used, Single-column eccentric press BERRENBERG Type EPtG 20-325 N-0 Mach. No. 15342, Year of manufacture 1974 Pressing force 20 tons Projection 320 mm Table surface 550 x 350 mm Through hole in table 190 x 120 mm Push surface 305 x 140 mm Table intermediate plate L x W x H 540 x 340 x 55 mm Through hole in table intermediate plate Ø 103 mm Clamping pin bore Ø 40 mm Stroke adjustment 8 - 70 mm Push adjustment 35 mm Installation height max. 345 mm (without table intermediate plate) Installation height max. 290 mm (with table intermediate plate) Table height above floor 700 - 750 mm (without table intermediate plate) Dksdpfx Aljv Tp D Hjbot Stroke rate 100 to 180 strokes/min. Drive power 1.5 kW Power supply 380 V, 50 Hz - Pneumatic clutch-brake combination, manufacturer: ORTLINGHAUS - Electric foot switch and two-hand operation - Stroke rate continuously adjustable via variator drive - Table height adjustment via threaded spindle approx. 150 mm - Manual central grease lubrication BEKA Schmiertechnik - Height-adjustable press table via threaded spindle - Electrical diagram Space requirement L x W x H 1600 x 850 x 1950 mm Weight 1250 kg Good condition

Condition: used, functionality: fully functional, Year of construction: 1989, machine/vehicle number: 4867, Pressta Eisele Stamping Machine HE 40 S Djdpfx Alsy Tizkjbjkt Price: 2,000 Euros

Condition: used, Year of construction: 1992, functionality: unexamined, Technical Specifications Make and model: Bruderer BSTA 25 EL Nominal capacity: 250 kN, 25 tons Year of manufacture: 1992 Year of control upgrade: 2020 Max. number of strokes: 100/1425 Adjustable stroke: 13, 16, 19, 25, 32, 38 mm Table dimensions: 640 x 530 mm Passage between the supports: Longitudinal 640 mm; Lateral 220 mm. Fitted with roll feeder BBV 190/85 on right hand side. Max width of strip: 160 mm Dodoyktftjpfx Albjkt Feed length: variable up to 85 mm max Optional: Sound insulating cabin Oil pump. Heat exchange oil cooler. Front and rear safety guards. Fitted on 4 spring feet. Slide/Ram adjustment: 51 mm Documentation included. Press weight cca. 5000 kg.

Condition: excellent (used), Year of construction: 2009, Punching machine Boschert EL500 Djdsid I Hhspfx Albskt Quick tool change system TRUMPF up to tool size III = diameter 105 mm Punching force: 280 kN (28 tons) Punching arm overhang 560 mm Side stop 1000 mm right/left Stroke 40 mm Total weight 2700 kg including tool cabinet with tools and accessories completely overhauled

Condition: used, Year of construction: 2001, functionality: fully functional, The Schaal SEP 80 is a 80-ton eccentric press designed for precision stamping and forming. Its Unidor electronic control system ensures repeatable stroke accuracy and fast setup, while the integrated tool safety device protects dies from damage caused by misfeeds or incorrect part positioning — reducing downtime and tooling costs. The machine features a rigid double-column O-frame in vibration-damping cast iron, 6-point play-free roller ram guidance, and a flywheel drive with pneumatic clutch/brake combination. It comes equipped with a gripper feeding device SZV 302 feed unit for automated strip feeding. Pressing force: 800 kN (80 tons) Strokes per minute: 60 – 320 min⁻¹ Ram stroke (adjustable): 8 – 80 mm Ram adjustment: 80 mm Ram surface: 700 × 500 mm Table size (clamping plate): 830 × 700 mm Clamping plate thickness: 80 mm Table opening: 500 × 200 mm Strip feed clearance: 120 ± 40 mm Feed unit: Schaal SZV 3 Strip width: 10 - 270 mm Thickness: 0 – 4 mm Dodpfezhw Husx Albskt Drive power: 21.5 kW Weight: 8,000 kg Footprint: 1,500 × 2,000 mm, height: 2,885 mm

Condition: used, Single-column – Eccentric press EBU, Type 75 SKU Machine No. P 4598462, Year of manufacture 1962 Pressing force 75 tons Dkedpfx Asdzqltslbjt Reach 300 mm Table area 800 x 620 mm Die opening 325 x 225 mm Slide area 470 x 180 mm Tool holder bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Slide adjustment 80 mm Maximum installation height approx. 420 mm Stroke rate 60 + 105 strokes/min Motor power 4 kW Power supply 380 Volts, 50 Hz - Pneumatic clutch-brake combination EBU - Overload protection with shear plate in the slide - Tool monitoring system UNIDOR, Type APS MINI - Mechanically driven strip feed with strip straightener OSTERKAMP, Type ZPN 200/350 - Strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds through 2 V-belt stages on the gear pre-stage - Two-hand operation - Simple work area guard that can be swung open - Table height adjustment in the lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and operator panel for tool monitoring located beside the machine - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons Good condition

Condition: used, Year of construction: 2003, Manufacturer: Haulick + Roos GmbH Type: RVD 3000-2500 Machine Type: High-performance stamping press Year of manufacture: 2003 Condition: used Rated pressing force: 3,000 kN Pressing force: 300 t Stroke frequency: 20–180 strokes/min Drive power: 80 kW Ram stroke: 20–160 mm Ram adjustment: 150 mm Tool installation height: max. 450 mm Maximum tool length: 2,500 mm Maximum tool width: 1,000 mm Table area: 2,450 × 1,000 mm Ram area: 2,500 × 950 mm Clamp plate opening: 2,250 × 350 mm Machine weight: approx. 46,000 kg Strip feed direction: right to left Power supply: 400 V Frequency: 50 Hz Maximum connected load: 80 kVA Maximum fuse rating: 250 A Draw cushion: not available Components of the system: Haulick + Roos high-performance stamping press RVD 3000-2500 DIMECO coil unwinder, type 23S1/D/VV Year of manufacture: 2003 Weight: 1,450 kg Maximum load capacity: 4,000 kg DIMECO roller feed, type 1681/17/BVV Year of manufacture: 2003 Weight: 540 kg ARKU straightening machine Technical data for roller feed: Strip width: 5–420 mm Djdpozrz Dxofx Albekt Strip thickness: 0.1–5 mm Maximum strip cross-section: 1,000 mm² Strip speed: up to 125 m/min Feed length: 0.1–999.9 mm Feed accuracy: ±0.1 mm Roller diameter: 100 mm Strip height adjustment: 100 mm, manual mechanical Note: The ram guide should be replaced. The system is currently still in operation and functional. A quote from the manufacturer for complete disassembly and installation of new guides is available for approximately €200,000. We will gladly provide videos of the system in operation upon request.

Condition: ready for operation (used), Schüco tools, pressing tools, stamping tools, Art. No. 293900, 290146-02, 299259, 290146, 293338, 293902, 296198, 299905, 296168, 293901, 280162, 296548, 293354, 287568, 290146-02, 296170, 296159, 297755, 293807, 296199, 299372, 293899, 282028-04, 283072-02, 280222-05 and 5 pieces without a number. Dksdpfxjd Sc D Se Albot

Year of construction: 2016, condition: ready for operation (used), Pressing force: 800kN, max. tool installation height: 380mm, max. upper tool weight: 300kg, stroke adjustment: 8mm-140mm, ram height adjustment: 100mm, stroke rate: 100/min, throat depth: 350mm, table dimensions X/Y: 850mm/670mm, ram area: 550mm/400mm. Machine dimensions X/Y/Z: approx. 2250mm/1550mm/2750mm, weight: approx. 9000kg. The machine was completely overhauled by the manufacturer in 2016 (retrofit). In 2024, the clutch, rotary union, press safety valve, and hydraulic oil cooler were replaced. In 2021, the drive motor and belt for the flywheel were converted to frequency-controlled speed. Documentation available. An on-site inspection is possible. Dedpfx Aoxq Exwolbekt

Condition: used, Single-column – Eccentric press RICHTER Type PEKRS 80 Year of manufacture 1970 – Overhauled in 2024 Clamping force 80 tons Reach 350 mm Table size 900 x 650 mm Through-hole in the mounting table Ø 200 mm Ram area 700 x 500 mm Stroke rate 70 strokes/min Stroke adjustment 6 – 100 mm Ram adjustment 85 mm Installation height max. 400 mm Arbor hole Ø 50 mm Table height above floor 810 mm Motor power 8 kW Power connection 400 volts, 50 Hz - Pneumatic clutch-brake combination ORTLINGHAUS - Press safety valve HERION XSz 32 - Pneumatic ram balancing cylinders - Overload protection with shear plate in the ram - Grease central lubrication with hand pump Space requirement L x W x H 1800 x 1250 x 2830 mm Weight 5.7 tons Very good condition Technically overhauled and converted to the latest safety standards with new electrical system Dsdpfxei Db Ibo Albjkt Control system rebuilt in 05/2024 – suitable for manual feeding operations – in accordance with DGUV Information 209-030 Press Inspection and Machinery Directive 2006/42/EC Low Voltage Directive 2014/35/EU EN ISO 16092-1: Safety of machinery - Presses - Part 1: General safety requirements EN ISO 16092-2: Machinery - Safety of presses - Part 2: Mechanical presses - Control system with plain text error messages and diagnostic screen for quick fault localization - New electrical cabinet, mounted on the side of the machine - Completely based on SIEMENS, with S7-1200 PROFIsafe PLC and 7" TFT touch display - Two-hand control panel with emergency stop and interlocking - Electric foot switch - Cam mechanism with run-on monitoring - Stroke release via press safety valve HERION XSz 32 with pneumatic pressure gauge - Rewiring of the machine - Updated operating manual The machine is equipped with 6 operating modes: 1 = Setup 2 = Single stroke, two-hand 3 = Single stroke, foot 4 = Continuous operation, foot 5 = Automatic continuous operation 6 = Reverse operation

Condition: ready for operation (used), Design: vertical press with four columns. Dsdpfx Alotty Nkjbjkt The vertical press platen is driven by an electric motor, the lower platen can be pulled out with the tool. -Dimensions: 2100x1600x3000mm -plate size: 950x1120mm -Electrical data: 380V; 43A; 22kW

Condition: used, Year of construction: 2017, Automatic cold press Manufacturer: CMB Type: PFR-CCL Year of manufacture: 2017 Technical data: Motorized loading table 3,500 x 1,600 mm for manual assembly of the plates and automatic loading into the press on the 1,600 mm side. Structure made of welded steel profiles. Devices for adjusting the working height to compensate for unevenness in the floor. Steel rollers. Foot switch. PRESS Plate size: 5,500 x 1,600 mm Loading side: 1,700 mm Stroke: from top to bottom Opening: 450 mm Cold press The plates are made of steel sheet and attached to a steel frame structure. Maximum pressing force: 160 tons. Specific pressure (on 100% of the area): 1.82 kg/cm2 Specific pressure (on 80% of the area): 2.27 kg/cm2 Pressure cylinder: 12 x 80 mm Auxiliary cylinders: 6 x 50/30 mm Power supply: 400 Volt EU/50 Hz/3 PH. + G AUTOMATIC LOADING and UNLOADING of the plates on the lower plate, on the 3,500 mm side. The transport is carried out via a motorized MYLAR belt. The belt is activated by 2 rollers, one of which is located at the entrance and one at the exit of the press. The rollers are driven by a motor with a chain that slides on special guides. The Mylar belt rotates around the lower plate, which rests on special side supports. The belt rotates on 2 rollers, which are located at the entrance and exit of the press. The ends of the MYLAR belt are attached to special rods with devices for tensioning the MYLAR. The upper plate is covered with a Mylar film. Dedpozuzw Dsfx Albekt The press plates consist of thick steel sheets that are welded to the frame structure. HYDRAULIC UNIT with pump, oil tank and valves for operating the pressure cylinders and auxiliary cylinders that move the upper plate. The hydraulic control unit is located in the upper part of the press to facilitate maintenance. CONTROL PANEL with buttons and switches. Pressure control manometer on the front of the press. UNLOADING MOTORIZED ROLLER TABLE 2,000 x 1,600 mm The unloading table is located at the exit of the press for manual unloading of the pressed plates. Exit side from the press: 1,600 mm. Note: The loading table of the press with the dimensions 3,500 x 1,600 and the unloading table with the dimensions 2,000 x 1,600 are shorter than the press table with the dimensions 5,500 x 1,600, as the press was installed in a line. Note: The technical data and descriptions are a transcript of the order confirmation at the time. The data is for informational purposes only and is not binding.

Year of construction: 2007, condition: ready for operation (used), Offered is a Kocher + Beck rotary die cutter/rotary die cutting system, sheet die cutting machine approx. year 2007. Sheet format X/Y approx. 500mm/720mm, material thickness up to max. 0.5mm, die cutting width max. 540mm, unwind max. 732mm, axial adjustment of the magnetic cylinder: +/-7.5mm, machine dimensions X/Y/Z: approx. 2100mm/1150mm/1500mm, weight: approx. 450kg. Inspection possible by arrangement. Dkedpfoxy R E Ujx Albet

Condition: excellent (used), Here, we offer you a TOX full-punch riveting system. TOX full-punch riveting system, type TZ-VSN. The full-punch rivet first severs all joining partners and then punches the rivet button out of the joining point. With its innovative technology for full-punch rivets, TOX PRESSOTECHNIK, the specialist for sheet metal joining, expands its range of products and services with a forward-looking process. Full-punch riveting provides an additional mechanical sheet metal connection, which is of great importance for lightweight constructions and the joining of hybrid parts and assemblies. Dksdpfx Aszdtffelbjt The rivet feeders, clamp and tool holders are also designed to be universal, so that full-punch rivets with diameters of 4.0 mm and lengths between 3.3 and 8.1 mm, as well as full-punch rivets with diameters of 5.0 mm and lengths between 3.9 and 9.0 mm, can be processed flexibly with both TOX hand clamps and TOX robot clamps. Type TZ-VSN Press force 55 kN Total stroke 140 mm Rivet type: diameter 5x4.6 Connection values Power: 3.4 kW Mains connection: 400/15/50-60 V/A/Hz Speed: 200 mm/s Mains type: 3P+N+PE Control voltage: 24 V DC Pre-fuse: 25 A Type: TZ-VSN Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data and information are subject to change!) We would be happy to answer any further questions you may have by telephone. Written orders can be placed by email or fax.

Condition: good (used), Hoza EMU punch This machine is ideal for punching out small molded parts from paper, rubber or textile goods. It has a high pressing force and fits on any stable table. The cut is initiated via a two-hand safety control. Djdpfxsuzhmte Albekt Forged blades or steel rule blades can be used in the machine. Knife stroke: 30 mm Max. punching format: 150 x 100 mm Weight: approx. 150 kg Color: hammer blow blue Dimensions: 450 x 360 x 600 mm Further items in other sizes - new and used - can be found in our store! International shipping costs on request!

Condition: excellent (used), A robust machine designed for punching holes in steel, aluminum, and other metals. Thanks to its foot control, it provides convenient and safe operation. Its compact design makes it suitable for both a locksmith's workshop and a production facility. Technical specifications: Manufacturer: Mubea (Muhr und Bender) Model: KL30 Year of manufacture: 1975 Machine number: 38601 Country of manufacture: Germany (West Germany) Power supply: 3× 220/380 V Frequency: 50 Hz Motor power: 1.5 kW Rated current: 5.8 / 3.4 A Protection rating: IP44 Control: foot pedal Punching capacity: Ø 30 mm in sheet metal with a thickness of 8 mm Ø 20 mm in sheet metal with a thickness of 12 mm (Parameters correspond to the manufacturer's nameplate for a material with a strength of approximately 45 kp/mm².) Condition: Used machine. Visual condition matches the photos. Djdezkmi Dspfx Albokt Robust, heavy-duty industrial design. Ideal for locksmith workshops, steel structure production, and workshops involved in metalworking.

Condition: good (used), Year of construction: 1998, Neat used punching machine from Euromac Type CX 1000 30 Dkedpfx Aezulx Eslbjt Capacity 30 ton Unloading 1000mm Overwrap up to 10000mm Including drawer cabinet with lots of tooling and multitool

Condition: used, functionality: fully functional, For sale is a MABI 8Z dished end punch which we used as a multi-hole punch. Dodpfx Alex Dbunjbjkt

Condition: used, Rotary transfer table, rotary indexing table with 16 stations Rotary transfer machine + hydraulic press TOX Rotary transfer machine, special-purpose machine with several assembly stations Manufacturing and assembly system using a rotary transfer process From the special-purpose machine manufacturer "AKE-technologies GmbH" Serial number: Order number: 11111 Year of manufacture: 2012 - large rotary indexing table WEISS, type TC500, with 16 stations Dkjdpfx Aogd D U Ejlbot - pressing station with TOX power unit - vibratory conveyor - conveyor belts - inspection stations - some stations are still visible in the pictures but have already been dismantled Space requirement L x W x H approx. 3500 x 2750 x 2300 mm Weight approx. 3000 kg All in like-new condition - The system has never been used in series production.

Condition: repair required (used), Year of construction: 1978, functionality: not functional, machine/vehicle number: 212 393, ram adjustment: 100 mm, pressing force: 160 t, stroke adjustment: 80 mm, overall weight: 18,000 kg, punching force: 160 t, We are offering this Haulick-Roos RVD160-1250 stamping press, manufactured in 1978, which requires repair. Pressing force during continuous operation: approx. 1600 kN Max. distance between table and ram: 350 mm Distance between the uprights along the length: 1250 mm Opening on the uprights, width x height: 640 x 460 mm Through hole in the table: 1000 x 250 mm Ram surface, width x depth: 1200 x 900 mm Dowel bore in the ram, diameter x depth: 50 mm Adjustable ram stroke: 20 – 100 mm Ram adjustment: 100 mm Stroke adjustable in infinitely variable steps: 50 – 300 mm Drive power: 22 kW Weight: approx. 18,000 kg incl. uncoiler and feed machine Uncoiler with feed machine: Manufacturer: Schleicher Type: 6-70 RM 76 Dkedpfxozdf Utj Albet Max. coil weight: Strip thickness: 0.5 – 4 mm Max. coil width: 650 mm Max. coil diameter: 1400 mm Power: 5.5 kW Year of manufacture: 1978 Feed and control: Including pre-piercing software ASTA All data are approximate. Technical specifications/equipment are non-binding and without guarantee. The machine is sold without any warranty or guarantee. Sale exclusively ex works, for dismantling or at additional cost. If you have any questions or require further information, please feel free to send us a message or call us.

Condition: used, Year of construction: 1994, Technical details: air pressure - required: 8 bar total power requirement: 14 kW machine weight ab.: 80-170/je Maschine kg MULTIFUNCTION PUNCH PRESS for alloy windows construction 3 pieces: - for Schüco alloy window frame, post and beam profiles S65 Dksdpju Icyhofx Albst - for Schüco alloy wing profiles for alloy window system ROYAL S 55, S 65 and S 70 - for Schüco alloy door profiles Royal S65 door base profiles - foot operation - pneumatic air gun AND - drilling automat for window construction application: - drill automat for door hinge - drill taper: for 8 pcs, usable tools 6 pcs, countersink drills with dia. 11/15mm approx. 80mm long - clamping operation via foot control and drilling via manual - accessories: diverse installation parts i.D. *

Condition: used, Single-column – Eccentric press PELS - RICHTER, type PEKR 125 Machine no. 20684, year of manufacture 1967 Pressing force: 125 tons Reach: 430 mm Table size: 1100 x 750 mm Ram surface: 890 x 650 mm Table opening: Ø 400 mm Stroke adjustment: 6 to 115 mm Dkjdefim Thopfx Albst Ram adjustment: 100 mm Installation height for maximum stroke at the top: max. 450 mm Arbor hole: Ø 50 mm Stroke rate: 60 strokes/min Table height above floor: 900 mm Motor power: 7.5 kW Power connection: 380 volts, 50 Hz - Overload protection by shear plate in the ram - Compressed air coupling-brake combination DESCH - Ram weight balancing cylinder - Manual ram adjustment - Two-hand operation - Cam indexing mechanism - Central grease lubrication system Vögele - Stroke counter Space requirement L x W x H: 2300 x 1450 x 3030 mm Weight: approx. 10 tons Good condition

Condition: ready for operation (used), Year of construction: 2003, functionality: fully functional, Fully automatic high-performance die cutter Renz Kugler 341-2R for calendars and ring binders 3 tools Conveniently operated by a single person, Kugler punching machines are suitable for use in even the tightest spaces. Equipped with a non-stop feeder and gentle top-fed material intake. Capable of trouble-free processing of mixed materials (e.g., cardboard and plastic). Precise alignment before the punching process ensures maximum accuracy. Ideal for perforating ring binder inserts, cardboard and plastic calendar/index sheets, paper for wire-bound products, and much more. Tool changes only require a few simple steps. After punching, a turning wheel maintains the correct sequence for printed and numbered products, transporting them to the delivery station. Precise and simple register adjustment. Performance features - Minimal maintenance required - Highly efficient Dedexduclspfx Albjkt - User-friendly operation - Fastest changeover between formats Technical data - Working width: 500 mm - Maximum punched page format: 500 mm - Maximum unpunched page format: 500 mm - Maximum punching thickness: 3 mm per layer - Punching speed: 110 cycles/min - Paper feeding: automatic, non-stop paternoster feeder - Paper delivery: automatic, box delivery with jogger - Paper grammage: min. 60 g/m², max. 2 mm (subject to gram/quality restrictions) - Register punching: yes (not included) - Interchangeable tooling - Tool changes require only a few manual operations - Quick format change, manual setting wheels - Adjustable edge distance - Punching unit can be selectively deactivated - Space required: 3.30 x 1.50 m - Net weight: 1,580 kg