Thread roller

INGRAMATIC RP1

Condition: refurbished (used), Currently undergoing rebuilt, it is possible to customize it. Ingramatic RP1 Fixed die length: 85 mm. Moving die length: 95 mm. Die thickness: 25 mm. Fsdjzcd Hfjpfx Albjgg Die height: 65 mm. Thread diameter: M2 ÷ M6 Shank length: 100 mm. Thread length: 62.5 mm. Speed Range up to: 600 pcs./min.

Condition: used, Year of construction: 1961, max. workpiece diameter 100 mm min. workpiece diameter 10 mm workpiece length 1000 mm total power requirement 16 kW weight of the machine ca. 3 t dimensions of the machine ca. 0 m The guides have been outdated 10 years ago Fsdpfx Aewwl I Ielbjgg

Condition: used, Year of construction: 1984, functionality: fully functional, thread length: 48 mm, total length: 75 mm, metric thread diameter (min.): 2 mm, metric thread diameter (max.): 6 mm, Ingramatic RP 1 # 451 1984 230-600 pieces 2.5–6 mm Blank length: 4–75 mm Thread length: 48 mm Tool dimensions: 95/85x25x48 Power: 12 kW Fjdpjy D Nghsfx Albjgg

Condition: good (used), Max Diameter: M6 Max thread length: 42mm Fedshtal Rjpfx Albsgg Max length of rods: 75mm Year: 80's

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Fodouz If Nspfx Albegg Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: refurbished (used), Year of construction: 1988, Ingramatic RP1V: M6x75/40 mm. 230-600 ppm. Also available with a tabletting machine. Completely overhauled to like-new condition. Fgjdpfeh Riuujx Albjg Machine can be viewed in Calolziocorte (LC). OVERHAUL ACCORDING TO CE STANDARDS. The overhaul includes: - DISASSEMBLY AND CLEANING OF EVERY COMPONENT - REPLACEMENT OF ALL BEARINGS - GRINDING OF GUIDES OR REPLACEMENT IF NOT SUITABLE - OVERHAUL OF FEEDING UNIT - OVERHAUL OF SLIDE UNIT WITH REPLACEMENT OF BRONZE BUSHINGS - NEW LUBRICATION SYSTEM WITH COMPLETE HYDRAULIC UNIT, INCLUDING PUMP, OIL LEVEL INDICATOR, PRESSURE SWITCH, AND DISTRIBUTORS - NEW WATER PUMP FOR FEEDING TRAY - NEW VIBRATORY FEEDER, Ø670, COMPLETE WITH VIBRATION CONTROL PANEL AND PHOTOELECTRIC SENSOR FOR OVERFILL PROTECTION - OVERHAUL OF ROLLER DISCHARGE UNIT - PROTECTIVE GUARD COMPLETE WITH LAMP AND MICROPHONE - INSTALLATION OF SOLENOID VALVE WITH NEW AIR SYSTEM FOR VIBRATORY FEEDER AND GUIDES - NEW ELECTRICAL SYSTEM ACCORDING TO CE STANDARDS, COMPLETE WITH INVERTER - NEW MOTOR - REPLACEMENT OF BELTS - RAL PAINTING IN THE COLOR YOU SPECIFY

Year of construction: 1988, condition: new, Ingramatic RP1/R for washer assembly M6x75/40mm. Fixed die length: 85 mm. Moving die length: 95 mm. Die height: 65 mm. Fgjdpfx Alelcbkgobeg 230-600ppm. Completely overhauled like new. Machinery visible in Calolziocorte (LC) REVISION ACCORDING TO CE STANDARDS. The review includes: - Disassembly and cleaning of each piece - Replacement of all bearings - Correction of guides or possible replacement - Introducer group revision - New washer assembly group - Slide unit overhauled with bronze gibs replaced - New lubrication system with hydraulic unit complete with pump, level switch, pressure switch and distributors - New die water pump - New cup vibrator diam. 670 mm. complete with vibrator control panel and overflow photocell - Revision of the roller evacuation group - Protective casing complete with lamp and micro - Solenoid valve installation with new air system for vibrator and guides - New electrical system in accordance with CE standards complete with inverter - New engine - Belt replacement - RAL painting indicated by you

Condition: new, metric thread diameter (min.): 3 mm, metric thread diameter (max.): 16 mm, overall weight: 500 kg, feed length X-axis: 3,000 mm, feed length Y-axis: 1,500 mm, feed length Z-axis: 200 mm, torque: 24 Nm, spindle speed (max.): 3,000 rpm, spindle speed (min.): 50 rpm, power: 0.005 kW (0.01 HP), The CMA 3-axis controlled tapping center is designed for the post-processing of laser-cut sheet metal parts and complete processing of small parts and tubes, for example. The machine offers the following processing options: - Thread cutting - Drilling (standard / with chip breaking / hollow profile cycle) - countersinking - Flow drilling (with optimum feed curve) - reaming - Simple graphical programming - Import of 2D DXF or DWG files - Machine table according to System 28 (similar to Demmeler and Siegmund welding tables, among others) - Radial compensation of the tool by means of patented tool holder (accessory) - Tool probe for length measurement and as a breakage detector Fodpfsrbz T Nsx Albegg - Intuitive safety system using light barriers Standard version: Automatic tool changer with 10 positions, mounted on the machine portal

Condition: good (used), Ingramatic RP1 Max diameter: M6 Max. thread length: 42mm Max. shank length: 75mm Year: 80's Fsdpfx Ashrdnkjlbjgg

Condition: used, Year of construction: 1988, Technical details: pressure: 10 t workpiece diameter - max.: 40 mm threading length: 70-80 mm workpiece diameter min/max: 3 / 40 mm revolution per minute: 47-94 U/min feed speed: 0,5 - 6 mm/s work stroke: max. 7 mm total power requirement: 4,68 kW Weight approx.: 1,4 t dimensions of machine: 1,4 x 1,4 x 1,7 B T H m dimensions of hydaulic: 0,8 x 1,2 m Hydraulic drive manual and automatic cycle adjustable roller speed max. thread diameter 40mm min. thread diameter 3mm up to 3.5 mm pitch max. pitch 1.75mm roller width min. 80 mm max. 120mm shaft speed 47-94 roller shaft diameter 40 various rollers as accessories Fjdpow D Aq Tofx Albsgg *