Screw making machine

INGRAMATIC RP1/V

Condition: new, Year of construction: 2024, functionality: fully functional, pressure: 16 bar, input frequency: 50 Hz, type of input current: three-phase, temperature: 400 °C, input voltage: 6,000 V, rotational speed (min.): 1,500 rpm, rotational speed (max.): 1,500 rpm, type of cooling: air, Industrial Steam Turbogenerator Howden – Model KK&K TWIN CA46, NEW, never installed or commissioned, still under manufacturer’s warranty. Following a revision of our long-term industrial strategy, a Howden KK&K TWIN CA46 steam turbogenerator is available for sale, supplied complete as per the original OEM scope. The unit is BRAND NEW, fully manufactured and tested by the OEM, but it has never been installed or put into service. It remains under the manufacturer’s warranty and has been stored in a closed, controlled environment. Kedpfxsyidvdj Abzonb Immediate availability eliminates typical production lead times, which for this type of equipment are generally 24–36 months. Main supply includes: - Steam turbine on skid with integrated gearbox - Synchronous generator supplied separately Turbine technical configuration: - Model: KK&K TWIN CA46 - Dual-casing turbine (Steam Part A + Steam Part B) - Integrated three-shaft gearbox (2 pinions + central wheel) - Controlled steam extraction between HP and LP sections (included) Main design conditions: - Inlet steam pressure (HP): 16 bar(a) - Inlet steam temperature: 400 °C - Electrical output at terminals: up to 1,595 kW - Nominal speed: 1,500 rpm Electric generator: - Three-phase synchronous generator - Rated output: 1,994 kVA - Voltage: 6 kV – Frequency: 50 Hz - Cooling: IC31, air - Brushless construction, parallel grid operation ready Included systems: - Integrated baseplate oil system - Main mechanical oil pump and auxiliary electric oil pump - Local panel on skid - Control and protection panel with Siemens SIPROTEC 5 system - Electronic speed and pressure governor - Independent overspeed protection device - ENC-RfG turbogenerator simulation model Typical applications: - Industrial cogeneration plants - Energy recovery from process steam - Biomass and waste-to-energy plants - Combined production of electricity and process steam Status and conditions: - Condition: NEW - Year of manufacture: late 2024 - Never installed – never commissioned - Still under manufacturer’s warranty - Complete OEM technical documentation available - Installation and commissioning support from the manufacturer available Potential application fields: - Biomass and waste-to-energy plants, for electricity and process steam production, with immediate unit availability, avoiding multi-year production lead times - Industrial cogeneration (CHP) for facilities with continuous process steam use (paper, food, chemical, manufacturing industries) - Revamping / repowering of existing plants, as a fast-track alternative to new OEM supply with 24–36 month delivery lead times Price: on request. Further technical information and documentation available upon request.

Condition: good (used), Flat-jaw thread rolling machine, thread rolling machine, segment thread rolling machine, cold forming machine, knurling machine, thread rolling machine -Manufacturer: EWM, flat jaw thread rolling machine knurling machine -Type: unfortunately without type designation -Drive: 4.6/5.8 kW 1435/2890 rpm -Belt drive: 3-way adjustable -Knurling plate: RAA 1.0 -Central lubrication: -Dimensions: 1680/920/H1440 mm Kodpfxei Eg Nke Abzonb -Weight: 1308 kg

Condition: ready for operation (used), Year of construction: 1970, functionality: fully functional, shaft length under head: 30 mm, section length (max.): 52 mm, Hilgeland CH1 KHA double-acting press Ksdpsur N Dajfx Abzsnb Year of construction 1970 The machine is ready for immediate use!

Condition: used, Year of construction: 2024, Rear section Primera DMC 4200 l 1-fold conveyor section Single-shoot distributor heads / f. 16 rows Long loading board for rear section Drawbar with folding support foot / lower linkage attachment Cat. 3 braked axle with parking brake / dual-circuit air brake system Knodpfouhnwvex Abzob

Year of construction: 2014, condition: repair required (used), functionality: fully functional, The machine has been idle unused for a few years now, so it needs maintenance before commissioning, which should be the responsibility of the buyer. Knjdpfotu U Ebex Abzsb

Year of construction: 1988, condition: good (used), Carlo Salvi 1 die 2 blow Ksdshrdmxspfx Abzonb Model 780/SV Maximum Cutoff dia.mm: 6,35 Max. Cutoff length mm: 97 Max. K.O. length (die side) mm: 80 Max. Speed, pcs, per minute: 360

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Kjdpfxjuz If Ns Abzenb Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: good (used), Year of construction: 2005, Used cutting machine Lectra Vector 5000 Fashion V3 - year 2005 - Useful cutting width 180 cm. - translating - new inverter device - in good condition. Knodortnccopfx Abzeb

Condition: new, Year of construction: 2026, functionality: fully functional, power: 80 kW (108.77 HP), number of axes: 2, overall weight: 172 kg, table length: 900 mm, table width: 600 mm, Equipment: documentation/manual, A mid-sized CNC laser machine designed to work continuously for small, medium, or large production. This model features a lifting table, giving you additional product options. A Wattsan laser cutter will be an essential assistant for your business. Effective and fast. Wattsan 6090 LT can cut up to 10–13 mm and engrave wood, cardboard, acrylic, glass, rubber, stone, wool, etc. The lifting table function allows lowering the working area up to 16 mm, so the rotary device may be installed to diversify your production. It also has a waste collection container that will make the work much more pleasing. You can give our managers a call for additional details! Wattsan 6090 LT characteristics Working area: 600x900 mm Laser power: 90-100 W Working table lowering depth: 160 mm Positioning precision: 0,03 mm Machine size: 1030 x 1490 x 670 mm + if it is on wheels 315 mm Packing size: 1110 x 1580 x 755 mm Weight: 230 kg Kodpeiim Unjfx Abzjnb Virmer provides not only prime machines but also service and delivery. Our engineers and managers are ready to answer all of your questions and provide video assistance if required. Also, owners of Wattsan equipment get lifetime online support. Virmer is located in the Netherlands and works all over Europe. Virmer is Wattsan's official supplier. We provide not only laser engravers, but also metal cutters, welders, markers and cleaning machines. Wattsan is a Chinese manufacturer, which has been creating laser equipment for almost 15 years and keeps evolving with the help of its clients. Thanks to feedback Wattsan made over 50 modernizations, which made machines more reliable, precise and powerful so you could upgrade your business up to the new level. YOU CAN WRITE OR CALL US! WE WILL SELECT THE RIGHT MACHINE FOR YOUR TASK On our company you can find a wide range of machines and components: Laser Metal Cutting Machine; Laser Metal Machine, Fiber Metal Laser, Fiber Metal Laser Engraver; CNC laser machine for metal; Laser machine for wood; CNC laser machine; Laser engraving machine; Laser engraver; Laser cutting machine for plywood; Laser engraver; Laser cutting machine for metal; CNC milling machine; laser marker. Lenses; Chillers; Cooling system for machine; Chiller S&A ; IPG laser, MAX photonics, Raycus; Compressor; Rotary device; Mirror for laser machine.

Condition: used, machine/vehicle number: 1 284 066, Feed diameter: 200 mm Kedpfocm Tgkjx Abzsnb Through-hole: 50 mm Mounting, short taper according to DIN 55027: Size 6 Outer diameter of the clamping cylinder: 290 mm Overall height (clamping cylinder to the front of the chuck, without jaws): 150 mm pneumatically actuated